Search Documents

By Richard J. Hartman

This presentation identifies some of the more common problems associated with cofferdam construction. After the various problems are identified, they are briefly explained and possible solutions and preventive measures are noted. Photographic slides used during the seminar illustrate the conditions. This discussion is limited to cofferdams which are braced structures excavated inside to allow access for construction. The common procedure is to drive sheet piling and then alternatively install bracing and excavate. They can be located either on land or in water. Loads are applied by soil, water, surcharge pres-sure, eccentricities, and impact loads. The loads are resisted by the sheet piling, the bracing, and the soil below the bottom of the excavation; each of these three components must be capable of resisting the applied loads.

Jan 1, 1987

By Norm Kirk, Robert Bittner

"The addition of a new powerhouse at the existing Tulloch Hydroelectric site on the Stanislaus River in the western foothills of the Sierras Nevada Mountains of central California required a deep excavation in rock on the downstream face of the dam. A cofferdam (water exclusion device) was necessary to isolate the powerhouse construction site excavation from the existing Goodwin Reservoir and the turbulent discharge from the existing powerhouse. The cofferdam was positioned on a steeply sloping fractured rock surface exceeding 50 degrees.This paper describes the challenges encountered during design and construction of the cofferdam and describes the unique design features used to address these challenges including:•,The use of flat-sheet-piles to form cellular walls on the steeply sloping rock surface.•,The use of 5-ft deep tremie concrete plugs in the bottom of the sheet pocket cells to create the bottom seal of the cellular cofferdam walls against the sloping rock surface.•,The use of vertical post-tensioned rock anchors to provide shear resistance at the contact point between the base of the cellular-wall and the sloping rocksurface.INTRODUCTIONModification or expansion of existing hydroelectric power plants often require downstream cofferdams or water exclusion devices to temporarily separate new construction from turbulent downstream discharge of the existing dam. Most dams are positioned on solid rock in the narrowest and therefore the steepest section of the river. This combination of steeply slopingrock and the need for an exclusion barrier creates a challenge for the design engineer trying to maintain a safe dewatered construction site. Typical cofferdam solutions for hydroelectric dams usually use large granular filled circular sheet pile cells that perform as gravity structures. However, this type of structures is not well suited to steeply-sloping highly irregular rock surfaces in a confined area."

Jan 1, 2017

By J G. Shellnutt, Y Iizuka, T W-Y Hsia, T-C Liu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of magmatic oxide ore deposits hosted in chemically-evolved layered gabbroic intrusions is attributed to a variety of petrological processes, but there is little to no consensus on the general applicability of each model. Complicating the matter further is that many layered gabbroic intrusions are spatially and temporally associated with alkaline A-type granites, suggesting that there is a petrogenetic relationship between the two types of chemically different rocks. Our experimental results show that petrological modelling using a starting composition of high-Ti basalt from the Emeishan large igneous province can produce evolved silicic liquids that resemble the compositions of microgranular enclaves from the syenitic unit of the bimodal, oxide ore-bearing Baima igneous complex. The experimental results confirm that bimodal gabbro-granitoid complexes can form from a common parental magma and that early crystallisation of Ti-rich magnetite can explain the formation of the oxide ore deposits in the lower parts of the layered gabbroic intrusions. We conclude that crystallisation of a typical high-Ti basaltic parental magma can produce world-class giant magmatic oxide ore deposits and that the occurrence of some alkaline granites may be an indicator of their presence.CITATION:Shellnutt, J G, Hsia, T W-Y, Liu, T-C and Iizuka, Y, 2015. Cogenetic formation of the peralkaline syenite and oxide ore-bearing layered gabbroic intrusion of the Baima igneous complex, Emeishan large igneous province, south-west China , in Proceedings PACRIM 2015 Congress, pp 317–324 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Pravin Mathur

"Praxair's CoJet® technology was introduced in 1997 to effectively inject chemical energy in electric arc furnaces. Coherent jets were invented as a revolutionary means of injecting oxygen and other gases into the EAF and into converters. Today, steel makers have widely accepted this concept in over 70 EAFs worldwide. Indeed, the whole industry has shifted to this new standard for chemical energy input in EAFs. CoJet® technology has also been implemented successfully in BOF converters.This paper will review the principles of coherent jets as applied to steelmaking. The key learnings garnered from several furnaces are also reviewed. In addition, while the CoJet® program has been widely accepted worldwide, based on steady feedback received from customers and the market place, several programs are underway in development and commercialization. These enhancements and new applications of CoJet® technology are also overviewed in the paper."

Jan 1, 2004

By Qiang Zhong, Bin Xu, Qian Li, Yong-bin Yang, Tao Jiang, Yan Zhang

The occurrence of different ringing behaviors in oxidized pellet kiln for two kinds of coal (A and B) with similar properties, is difficult to explain based on the relationship between kiln ringing and coal properties. In this paper, the interaction of coal ash with pellet scrap powder was considered by studying the cohering behavior of powders consisting of them. The results showed that the cohering briquette strength of pellet scrap powder increased considerably when mixed with a small amount of coal ash; a maximum could be reached when the mass percent ratio of coal ash was 1.5%; the strength of powder mixed with coal B ash was always higher in same firing system. This obviously illustrated that coal B caused a more serious ringing problem. The relevant mechanism was that the stronger reactivity of coal B ash made cohering briquette have a more perfect crystallization and a more compact structure.

Jan 1, 2015

By Bin Xu, Qian Li, Xiaoliang Liu, Yongbin Yang, Tao Jiang, Yan Zhang

The cohering behavior of iron ore pellet powder in kiln cannot be reflected entirely through the conventional briquetting method, so a novel natural stacking method was proposed in this paper. The results showed that in the two methods the cohering strength of powders from different iron ore pellets (numbered A, B and C) rose with the increase of roasting time and temperature andpresented the same result, i.e., C > B > A. Comparatively, the natural stacking powders obtained much lower cohering strengths under the same roasting condition. The structure analyses of ring from the kiln tail and cohering briquette by the natural stacking method indicated that the occurrence of crystallized particles of them were extremely similar. Therefore, the initial information of pellet powder’s cohering behavior could be provided by the natural stacking method, improving the methods to study the actual ringing process and mechanism of pellet powders in kiln.

Mar 1, 2017

By Diana Diaz, Rakshith Shetty, Vitaly Proschenko, Mike Mooney

Cohesive clay soil poses a significant risk to earth pressure balance tunnel boring machines (EPBM) due to unstable face pressure, clogging potential, high cutterhead torque, poor muck flow, low advance rate, etc. This paper details the performance measures desired when EPBM tunneling in clay soil, and the scientifically-supported conditioning methods to transform in-situ clay to a muck with such characteristics, giving particular attention to ground conditions. The paper then examines TBM data from multiple clay soil projects in the context of these performance measures to demonstrate the influence of cohesive soil conditioning on EPBM performance.

Jun 13, 2023

The Report on the Manufacture of Coke for the year 1880 by J. D. Weeks1 includes an historical account of the early days of coke-making that is very complete and accurate, and but little can be added to it to fully cover the period prior to 1885. The few additional references that have been found follow. The earliest suggestion found about making coke in this country is in a letter from D. M. Randolph to Harry Heth, dated August 22, 1808. Heth was then operating the mines in the Richmond, Virginia coal field and had sent Randolph to England to investigate steam engines for hoisting and pumping and other conditions in the coal industry there. The letter was written in London and said: "I shall explain to you, how, by turning Deep Run fine coal in Coak, to make great profit from what has heretofore been useless. You will do well to ascertain the price and amount of demand for this article throughout the U. States among brewers and manufacturers. I know how also to make every bushel of such fine slaty coal, fetch as much as any of the best grate coal, by turning it into Coak: and that too, after paying all expenses of the process."2 His interest was to use the slack more for domestic purposes than otherwise, probably, although what the interest of brewers would be in coke as fuel does not appear. Nothing ever came of this suggestion, and so far as known, no coal from this field was coked excepting in gas-making. The Plumpsock Iron Works, mentioned by Weeks as having used coke, was advertised for sale in June 1818.3 It was stated that stone coal was the only fuel used at the works, the pit being within 100 yards of the forge. "Three men with a horse and cart are sufficient to raise coke, and haul to the forge all the coal necessary for keeping the works in full operation." The coke, of course, was made in ricks, or heaps, and not in ovens. The first real coke oven in this country was probably built in Connellsville, the coal coming from a mine nearby on Mounts Creek. L. L. Norton operated an iron foundry and was persuaded by his foreman, one Nichols, who came from Durham, England to build a coke oven. The oven was 12 feet square, and the first coke was produced in 1833. Later

Jan 1, 1942

By F. W. Jr. Sperr

THE byproduct coke oven is the most important artificial source of fuels for metals melting. Its products are solid, liquid, and gaseous in form. The amount of coke and primary byproducts obtained per ton of coal varies with the nature of the coal. The following represents the results obtained in many plants: Metallurgical coke (over 3/4 in.) 69 per cent. of coal Domestic coke (1/2 to 3/4 in.) 2 per cent. of coal Breeze (under 1/2 in.) 4 per cent. of coal Surplus gas, cubic feet per net ton 6600 Gas for heating ovens, cubic feet per net ton 4400 Tar, gallons per net ton 9 Ammonium sulfate, pounds per net ton 25 Benzols, gallons per net ton 4 All of these products, except ammonium sulfate, have important fuel value. Part or all of the metallurgical coke may be crushed or screened to furnish additional domestic coke. If producer gas is used, there will be a surplus of 11,000 cu. ft. of coke-oven gas per net ton of coal. The use of coke in the metallurgical industries has been retarded by the mental attitude of writers who disregard the dependence of coke quality on the conditions of its manufacture. Terms like "byproduct coke,"' "beehive coke," "48-hour coke," and "72-hour coke" are only generally descriptive and tell nothing of the coke quality. For example, one writer1 stated that in brass-foundry practice, Connellsville coke is considered much superior to byproduct coke on account of the high sulfur content of the latter. Another2 says, "At equal prices for hard Connellsville coke and for byproduct coke at the foundry door, the hard coke is unquestionably cheaper. It will melt more metal per ton than the byproduct coke and requires less labor, as the byproduct coke is less dense and burns faster, thus requiring more frequent firing." A little study of the conditions under which coke is manufactured will show the error in mak-

Jan 10, 1920

By Hyslop W

It is shown that coke has a major influence on the pattern of operation and on the aerodynamics of the blast furnace and that the physical and chemical characteristics of coke, at each stage in the furnace, determine its ability to satisfy requirements for iron production and coke economy. Analysis of coke sampled from operating furnaces is compared with furnace behaviour. The available data suggests the importance of segregation, strength, size change and chemical degradation of coke on furnace performance. Correlations are presented for coke breakdown ratio as a function of coke rate and hearth diameter which shows that breakdown increases with hearth diameter and with decreasing coke rate. It is also shown that the Micum tests do not reflect the coke strength in a predictable way and that solution reactions appear to play an important role in giving rise to a pitting effect on the cell walls of the coke with the resultant deterioration in coke properties. The catalytic effect of activating substances, such as alkalis, is noted and results are presented which show the effect of carbon solution on the coke strength. The importance of coke in the stack and in the bosh is discussed and flooding results are presented for BSC furnaces which show the probable driving limits for the furnaces considered. It is also shown that coke sampled from different tuyeres in a furnace gives quite different flooding limits. Other applications of the coke test work at BSC are also noted and the relevant objectives listed.

Jan 1, 1975

By Konishi Y, Morioka Y, Okabe K

A part of the results of dissection survey of Chiba No.1 blast furnace, Kawasaki Steel Corporat- ion, is presented. Distributions of coke size and of slag and metal holdup are shown in the region of the dropping zone. A similar relation to the irri- gated packed bed is obtained. The distribution of coke size, coke temperature and liquid holdup are measured in and around the raceway. The shape of raceway in the horizontal and vertical sections indicates that each raceway worked individually. Liquid flow in the dropping zone and around the raceway on the basis of holdup measurements is Discussed.

Jan 1, 1981

By C. Desmeules

"Carbon addition in the oxide pelletizing process is a big concern at the Sidbec-Normines pelletizing plant since 1976.Laboratory pot-grate testing carried out before the initial start-up of the Port-Cartier plant indicated that the nominal pelletizing grate capacity could be increased by fifteen per cent with a suitable carbon addition. Also an improved induration cycle offered the possibility of a significant energy reduction within the process with no adverse effect on pellet quality. A one-month plant scale program duplicated the lab test results and confirmed the anticipated cost saving by using these techniques. Since March 1980, Sidbec-Normines used coke addition as a current operation.This paper reviews briefly earlier laboratory and in-plant test work carried out to investigate the effects of adding carbon materials to the Fire Lake hematite concentrate, and presents operation techniques and plant results of carbon addition in the Port -Cattier pellet plant.IntroductionThe Sidbec-Normines pelletizing plant at Port-Cartier, Quebec, is designed to produce six million ton s per year of oxide pellet s. It is a Dravo-built two-line plant; one line to produce three million s tons per year of blast furnace grade pellets averaging 5.5 per cent silica, and another line of three million ton s to produce direct reduction grade pellets of about 2.0 percent silica.The laboratory pot-grate test program was conducted in 1977 at the British Steel Corporation Research Laboratories in England, with the assistance of J .E. Appleby, consultant to British Steel Corporation (overseas services) Limited.The purpose of that test program was to determine the optimum energy saving cycle and to study the physical and metallurgical effects on blast furnace and direct reduction pellets."

Jan 1, 1983

By John D. Price

In the constant search for ways and means of improving the quality of coke and thus making its use at the blast-fornace more satisfactory and economical, it has become increasingly evident that the present laboratory tests do not show the full picture of a coke's value as a blast-furnace fuel. This fact was recognized by Dr. A. C. Pieldner thirty-five years ago: (Ref. 1) here is perhaps no phase of fuel technicology which has aroused more discussion or regarding which there is more difference of opinion than the properties of coke which make it most suitable for blast-furnaces and other uses." Dr. Fieldner followed this assertion with a statement to the effect that men who write on this subject today (1923) have, because of conflicting experimental evidence brought forth in recent years, far less positive opinions on the matter than did writers of some years past. One is led to wonder if these statements are not just as true now as they were when first made.

Jan 1, 1959

By A. Eilers

I PRESENT herewith, for the inspection of the members of the Institute, a specimen of coke, made in gas-retorts from the lignite of Trinidad, Colorado.

Jan 1, 1874

"Only the coal of the Sunnyside district in Carbon County is coked. Two companies, the Utah Fuel Company and the Columbia Steel Corporation, operating adjoining mines at Sunnyside and Columbia, produce coke.The Utah Fuel Company has 819 beehive coke ovens at Sunnyside. Only 350 ovens are being operated at the present time, largely because the smelters which had been using Sunnyside coke changed their equipment from blast furnaces to reverberatory furnaces.The Columbia Steel Corporation operates a plant of 33 Koppers type by-product coke ovens at Ironton, near Provo. About 800 tons of coal are used per day to produce coke for the company's iron blast furnace plant pie ovens produce about 400 tons of coke, 12,000,000 cubic feet of gas, 9,000 gallons of coal tar, 3,000 gallons of benzol and several tons of ammonia sulphate per day.The total coke production for the State from the earliest output of record in 1880 until June 30, 1924, is 5,947,714 tons."

Jan 1, 1925

By R. W. Shoenberger, J. A. Grina, R. J. VanPelt

The many alternatives open to coke plant operators for improving overall coke quality and strength are discussed in this paper. Programs undertaken by US Steel research and coal operations during the previous ten years to improve coke strength are described. New techniques in use, or being considered for future use, are also discussed.

Jan 1, 1982

By T. H. Wilson

In 1901, the Crow's Nest Pass Coal Company, Limited, began producing industrial coke in 212 beehive ovens at Michel colliery. By 1908, 486 ovens had been installed and in that year 147,623 tons of coke were produced. Coke manufacture has been continuous from 1901 until the present time (1946), with total production of 2,795,402 tons. At present writing, only 100 beehive ovens are operating and production is reduced to 1,800 tons per month, due to the shortage of suitable labour. These ovens are drawn by hand, on contract, and the workmen are exposed to considerable heat. A man draws three ovens in eight hours, thereby producing approximately 1072 tons of coke per day. In addition to the inefficient and costly method of drawing coke in beehive ovens, tremendous losses are experienced in the wastage of gas and tar, which are driven off into the atmosphere. Also, the yield of coke per ton of coal fed to the ovens is low as part 9f the carbon is utilized in producing heat to carbonize the remainder of the coal. A recovery of only 55 per cent of the carbon, as coke, is obtained. The coking process takes place from the top of the charge, which is 21/2 feet deep, downward to the floor. Six and a half tons of coal are charged and 3.6 tons of coke are drawn from the oven after 72 hours' carbonization. The beehive ovens using Michel coal produce a very hard and tough coke, large in size and of silvery appearance, which has served the requirements of both foundry and smelter for many years. In 1938, the Company made a careful study of coking processes with a view to introducing a more economical method than beehive ovens and one that would be less dependent on skilled labour, the supply of which was rapidly diminishing at that time. Various methods of by-product coking were investigated, and it was decided that the Curran-Knowles process offered the greatest possibilities because of the low capital investment in relation to output and also because the horizontal oven design was suitable for an expanding coal. Consequently, a test on Michel B seam coal, supervised by Mr. E. Burrough, of the Fuel Research Department, Ottawa, was run in the Curran-Knowles plant at West Frankfurt, III. The results of this test led to the construction of a ten-oven battery of 32 ft. 6 in. by 8 ft. 3 in. Curran-Knowles ovens at Michel, which were completed in November, 1939. This battery was built as an experimental unit, with provision for an additional ten ovens if the coke proved satisfactory for the market. In 1942, an expanding coke market led to the construction of a second battery of ten ovens, which were completed in April, 1943.

Jan 1, 1947

By Huanyu Zhang, Quanqiang Ma, Huiqing Tang

Improvement of the coke quality for blast furnace (BF) iron making by hydrothermal oxidation treatment on coke quality was investigated. Results show that, under subcritical condition, sulfur removal rate is 15% and the weight loss is 3%; under supercritical condition, both sulfur removal rate and mass loss rate increase with the increase of H2O2 concentration. In the experimental conditions, sulfur removal rate and mass loss rates were 45% and 17%, respectively. Hydrothermal oxidation treatment could reduce the CO2 reactivity of the coke and the treatment under supercritical condition is more effective. Hydrothermal oxidation treatment could improve the graphitization of the coke and smoothness of pore boundary in the coke and the treatment under supercritical condition is more effective.

Jan 1, 2016

By Mariano de Córdova

In this paper, the coke oven life prolongation technology is reviewed from different points of view: blend design; battery heating; operational control; refractory maintenance. A summary of major inspections in critical areas, for the evaluation of the battery conservation situation is presented. A discussion on tools for the diagnostics of the degree of damage is carried out.

Aug 16, 2017

By Coin CDA

From a study of coke samples obtained from the tuyere level of four Australian Blast Furnaces, the nature of in-furnace coke degradation has been investigated. At the periphery of the raceway is a concentration of fines and the lump coke appears dull and rounded. However coke from the deadman is angular and relatively undegraded. Cokes made from higher rank coal appear to suffer preferential attack of the reactive maceral derived component (binder). The coke from lower rank coal appears to be attacked non-preferentially by the solution-loss reaction. Initial attempts to simulate these phenomena have given results consistent with these findings. From chemical analysis of the tuyere probe samples there appears to be a relative increase in carbon and decrease in-.sulphur and phosphorous between stockline and tuyere level. An overall decrease in coke mineral matter derived material was noted and associated with this was a significant gasification of silicon. Consequent formation of silicon carbide was noted.

Jan 1, 1981