Search Documents

By Jerry D. St. Clair

A multidisciplinary team of scientists and engineers at Wont has been working to understand heavy metal contamination of DuPont process waste streams and technologies for abatement of these metals. As part of this effort, an extensive study was made of a specific waste stream of importance in DuPont's environmental commitment. This 200 gpm stream contains 5-5000 ppm of nickel plus a variety of inorganic and organic constituents. The chemical complexity of the waste rendered conventional. alkaline precipitation ineffective, and only through the simultaneous application of analytical characterization, fundamental chemical understanding, and process engineering did effective technical approaches emerge. In this instance, ion exchange, sulfide precipitation, and caustic digestion ultimately proved successful in reducing the nickel to below the 1 ppm target. The results of this study will be presented, along with key learnings about the process of solving heavy metal contamination problems.

Jan 1, 1994

By Shilai Yuan, Huimin Lu, Liyuan Zhao, Zhijiang Gao

"A purification process was developed to removal impurity element boron from metallurgical grade silicon by electromagnetic induction slag melting. Vacuum melting furnace was used to purify boron in both Al2O3-MgO-CaO-SiO2 slag system and Al2O3-CaO-SiO2 slag system. The relationship between different slag chemistry and the removal of boron in silicon were studied using Back Propagation (BP) Neural Network model. The best slag chemistry for the removal of boron was predicted by Genetic Algorithm (GA) contributed by the use of Matlab. The results show that the mass fraction of Boron in silicon is reduced from 11.7496×10-6 to 2.3259×10-6 after slag melting in 28.96%Al2O3-3.43%MgO-36.24%CaO-31.37%SiO2 slag system. The relative error obtained with GA-BP Neural Network model was below 0.35%.IntroductionSolar energy, due to its low green house gas emissions, has been paid great attention. Accordingly, the demand for solar grade silicon (SoG-Si) has been growing rapidly. The quest for developing a low-cost method of producing SoG-Si has been moving forward in the last decade. Refining of metallurgical-grade silicon (MG-Si) attracts research interest due to its low material and energy costs, and more environmentally friendly technology in comparison to the traditional Simens process. As such, impurity elements in MG-Si must be removed to low levels for the photovoltaics (PV) cell to operate at optimum efficiency. Most impurities in metallurgical-grade silicon (MG-Si), especially metal elements, can be separated by directional solidification and the zone refining plasma-arc method [1, 2]. The main focus in refining MG-Si to SoG-Si is on the impurities which are the most difficult to remove. Boron has relatively high segregation coefficients (KB=0.8, concentration of Boron in solid silicon divided by its concentration in liquid silicon) [3] and higher vapor tension (the saturated vapor pressure of boron and silicon are 6.78×10-7 Pa and 0.4 Pa, respectively). The vacuum melting and directional solidification methods hence have no effects on boron removal.Slag refining involves melting MG-Si in the presence of a flux to produce a slag phase that can take up the impurity elements. The mechanism of slag refining is considered to include two main steps: the oxidation of boron and the absorption of boron oxide by slag materials. The oxidation of boron, described by the oxygen potential (PO2), resulting from the equilibrium Si and SiO2. The absorption of boron oxide, described as the slag basicity, is interpreted as expected to facilitate their extraction to alkali and alkali-earth oxides in the slag phase. Thus, effective removal may be obtained for a certain slag composition. Researchers [4-5] examined the effect of boron removal in CaO-SiO2 based ternary systems and showed that the addition of excess CaO can decrease the activity of SiO2. Researchers [6-8] studied the boron behaviors in CaO-SiO2-Al2O3, CaO-SiO2-Na2O, Al2O3-BaO-SiO2, CaO-SiO2-Li2O and Al2O3-CaO-MgO-SiO2 slag systems by adding boron in the silicon to a degree. Li2O, Na2O, MgO and BaO are thought to be associated with B2O3."

Jan 1, 2014

By Hong Yong Sohn

A novel flash ironmaking technology is under development at the University of Utah under the support of U.S. Department of Energy (DOE) and American Iron and Steel Institute (AISI). The history of the development from the conception of the idea to the current status will be discussed. The flash ironmaking process produces iron directly from fine iron ore concentrates without requiring cokemaking and pelletization/sintering, which will enable the technology to significantly reduce energy consumption and carbon dioxide emissions compared with blast furnace ironmaking. Unlike other gas-based ironmaking processes, this technology will not suffer from the problems of solid sticking and fusion. Current work is focused on the method of supplying the energy required to maintain the necessary temperature, as an intermediate step to determine the scalability for larger, industrial-scale pilot trials.

Jan 1, 2014

By Sang-Beom Lee

For thermodynamic prediction, the deoxidation equilibrium of aluminum in Fe-36%Ni alloy was studied with a cold crucible under Ar gas atmosphere at 1773K. For the deoxidation reaction in liquid Fe-36%Ni base, i.e.: A12O3(s) = 2A1 + 3O The interaction parameters and the equilibrium constant between aluminum and oxygen in liquid Fe-36%Ni alloy are given in the following: eo Al = -3.8, roA1=0.9, eAl° = -6.4, rAl° = 700, rAIAIo = 3.1, roA1o = 833 within the composition range of [Al] < 1 mass%. The temperature dependence of the equilibrium constant was obtained in the range of 1773K < T < 1973K by using reported data and present results as follows: log KAo= 0.58-24463.7 / T The deoxidation equilibrium with aluminum in Fe-36%Ni could be thermodynamically well described in the range up [Al] < 1 mass% with first and second order interaction parameters as well as the equilibrium constant determined in this study.

Jan 1, 2002

By M. Misra

The finely dispersed kerogen particulates present in the dilute suspension can be coagulated with the aid of a hydrophobic organism, Mycobacterium Dhlei. The initial coagulation and aggregation are strongly dependent on pH and organism concentration, the isoelectric points of oil shale kerogen and Mycobacterium phlei are at pH 3 and 1.8 respectively. As a result the aggregation is rapid around pH 3. Preliminary results show that it is quite possible to use microorganisms for enhanced dewatering of kerogen concentrate produced by froth. flotation.

Jan 1, 1991

By Aiyuan Ma, Tu Hu, Chenyu Sun, Yonggang Zuo, Hongying Xia, Jinhui Peng, Libo Zhang, Yongguang Luo

"In this study, the adsorption characteristics of tannin acid in aqueous solution were investigated using regenerated activated carbon (AC), with the aim to remove the tannin acid organic matter from the solution after zinc hydrometallurgy and Ge precipitation. Results showed the temperature has little effect on the adsorption ability (q.) of the regenerated activated carbon. The experimental equilibrium data were tested for the Langmuir and Freundlich isotherms. The adsorption equilibrium was better described by the Langmuir isotherm (R2 > 0.99). Pseudo first- and second-order kinetic models were used for describing kinetic data. It was determined that the kinetics of tannin acid removal was well fitted by second-order reaction.IntroductionGermanium recovery is a complex processes [1]. Hydrometallurgical processes are favoured and these are based on the precipitation of germanium as hydroxide or sulphide or alternately with tannic acid [2]. However, in the germanium recovery process, too much tannin is consumed by the germanium-tannins complexation process, and results in a high content of tannic acid remaining in solution, which is harmful to the valuable metal recovery [3]."

Jan 1, 2014

By R. Leiby

Prior to March 1992, the only component of the lead acid battery that was not recycled by East Penn Manufacturing Company was the sulfuric acid electrolyte. This acid was unusable in new batteries because the iron level was found to exceed new product specifications. The development of a liquid ion exchange process to remove the iron from the acid allows East Penn to currently recover over three million gallons of sulfuric acid annually. The process is based upon the use of an iron selective liquid ion exchange material or solvent to extract iron from the sulfuric acid electrolyte followed by regeneration of the solvent. Equilibrium and kinetic data for the extraction and regeneration steps were collected in order to scale up the process to commercial scale. An electrochemical process for the treatment of the acid used in the regeneration step was, also developed which significantly reduces the volume of strip acid required in the process.

Jan 1, 1995

By Kotaro Ogura

"The electrolysis process in which CO2 is selectively reduced to C2H4 at a three-phase(gas/solution/metal) interface on a copper-mesh electrode has been developed in a concentrated solution of potassium halide. At open-circuit potential, CO2 is captured on the electrode by being inserted into the double-layer consisting of halide anions specifically adsorbed and potassium cations which are located in the Helmholtz inner and outer layers, respectively. CO2 thus activated is subjected to the electrochemical reduction. In the early stage of reduction, CO2 is converted to formate radicals that are adsorbed on the electrode by taking the place of halide anions. The reductive coupling of these radicals results in the formation of intermediates such as -CH2C(O)- and CH2=CH-, and C2H4 is finally produced. The catalytic activity of the electrode process involving the insertion of CO2 into the double layer is not deteriorated at all during the electrolysis, and the continuous reduction of CO2 to C2H4 is possible with the addition of inorganic acid under the assistance of natural energy.Carbon dioxide is a serious pollutant released from fossil fuel power station, internal combustion and many industrial operations. The easy release of CO2 to the air has caused the global warming, and the technique which intends to curtail CO2 by pushing it back into the ground has been suggested. However, this problem should be greatly mitigated if CO2 can be converted to innocuous substances. Especially, the reuse of CO2 as fuels and chemicals is extremely effective not only for the mitigation of the global warming but also against the depletion of the fossil fuel reserves. Several processes for converting CO2 to valuable compounds have been proposed including hydrogenation over heterogeneous catalyst at high temperature and electrochemical and photochemical reduction. In the conversion and cutback processes of CO2, however, it is of importance that the process is feasible under mild conditions, because the secondary generation of CO2 is feared if high energy is required and supplied with a fossil fuel. In this meaning, the electrochemical reduction of CO2 taking place at room temperature, which is similar to photosynthesis, is promising. From the practical point of view, it is further necessary that the conversion rate is high enough and the product is satisfactorily valuable."

Jan 1, 2008

By Zhiqiang Han, Anil K. Sachdev, Baicheng Liu, Guomin Han, Alan A. Luo

The growth of precipitate phase ,B-Mg11Al12 in Mg-Al alloy is closely related to interface anisotropy and elastic interaction. The aim of this work is to investigate the effects of the interface anisotropy and elastic interaction on the morphology evolution and growth kinetics of the precipitate. In the work, the precipitation of ,B was studied using phase field modeling. In the model, the chemical free energy of the precipitate and the matrix were obtained via thermodynamic calculation. It is demonstrated that the interface anisotropy results in lath-shaped precipitate and the elastic interaction affects the shape of the end of the precipitate. The interface anisotropy causes uneven growth in different directions and the elastic interaction influences its preferential growth orientation. By combining the interface anisotropy and elastic interaction in the phase field modeling, the results showed that the precipitate phase has a lath-shape with lozenge ends, which is in agreement with experimental observations.

Jan 1, 2013

By Volker Uhlenwinkel

The design of a free fall atomizer as well as the process parameters affect the particle mass flux distribution in the spray cone. The mass flux distribution is important in spray forming because of its influence on the deposit shape and enthalpy input into the deposit. In this article the effect of different process parameters on the mass flux distribution is shown. Furthermore, different melts were atomized with the same atomizer. An empirical correlation will be introduced to predict the mass flux in the spray cone. This correlation will be compared with experimental results.

Jan 1, 1999

By Jenq-Gong Duh, Jyh-Wei Lee

"Hard chromizing process is a method for developing a surface modified coating providing wear, corrosion resistance and high temperature surface protection. Two carbon steels with 0.45 wt% and 0.95 wt% carbon contents, respectively, were chromized with pack cementation process at 950'C for 4 and 9 hours, respectively. The phase transformation and microstructure phenomena of chromized coating layer and matrix of two steels were studied with X-ray diffractometer and electron probe microanalyzer. (Cr,Fe)23C6 and (Cr,Fe)7C3 carbides and (Cr,Fe)2N1-x nitride phases were observed on the chromized surfaces. The thickness of chromized layers obeyed the parabolic rate law. The mechanism and diffusional kinetics of the chromizing process were proposed. The diffusivity of chromium in the (Cr,Fe)7C3 carbide phase was calculated using the moving boundary method.IntroductionChromizing process is one of the surface treatment technologies that can produce a chromium contained surface layer with sufficient corrosion and wear resistance on the steel matrix [1-7]. The relatively low cost and no ""line-of-sight"" restrictions are main advantages of chromizing. Adequate bonding strength of these coatings to the substrate was reported [7]. Chromizing process can be classified into soft chromizing and hard chromizing [2]. Soft chromizing is applied to steels containing less than 0.1wt% carbon through which chromium will be diffused. High temperature oxidation resistance improvement is the main purpose of soft chromizing process. On the contrary, the hard chromizing can be applied to steel containing more than 0.3wt% carbon, and very hard chromium nitride and carbide layers will be formed on the surface, which are very resistant to wear, corrosion and temperature [5-7]. In the previous studies on the Fe-Mn-Al-Cr alloy [5,7] and carbon steels [6], the thickness (X) of chromizing layers was analyzed and found the parabolic rate Jaw prevailed:"

Jan 1, 2004

By F. J. Tavera

A study on the electro kinetics of lead carbonate, silica, and alumina, in aqueous media was carried out at different pH values. The behavior of potential was determined for these species in the pH range between 3 and 12. Homocoagulation of lead carbonate in aqueous media is analyzed at its isoelectrical point. Lead carbonate heterocoagulation is analyzed with silica, alumina, and silica ? alumina mixtures at low pH values. The experimental results are considered for their possible application to treat residual water polluted with lead.

Jan 1, 2006

By E. M. Weenink

A proposed alternative to the conventional zinc extraction processes is the flash reduction of zinc calcines. As part of an overall study of this process, the kinetics of single zinc oxide pellets were investigated. Pellets, compacted from Outokumpu zinc calcine (60.9% zinc, 9.6% iron), were suspended in a flow of CO/CO, mixtures and reduced at temperatures between 1000 and 1200°C and atmospheric pressure. The pellet weight loss with time was recorded and analyzed. It was found that the reduction of calcine pellets (0.9 cm height and 1.36 cm diameter) was controlled by chemical reaction. This paper includes an analysis of the experimental results of two previous investigations of ZnO reduction.

Jan 1, 1992

By Noel A. Warner

Modern steelmaking is based on direct use of oxygen in high intensity batch reactors. A totally new approach is proposed in this paper, based on the view that pursuit of high intensity is unlikely to lead to successful coal-based continuous steelmaking. By substituting carbon dioxide and water vapor as the oxidants rather than using oxygen directly, the intensity is greatly reduced. Accordingly, subsurface formation of carbon monoxide bubbles can be avoided by careful manipulation of the three participating rate processes, gaseous diffusion, interfacial chemical kinetics and liquid phase mass transfer. Steelmaking can then be carried out without explosive ejection of molten droplets and the generation of micro-spray but rather in a controlled and fume less fashion. The vital component is the introduction of generic melt circulation technology. Three melt circulation loops in series are envisaged. Starting with a composite feed of iron ore fines, pulverized coal and lime flux, a metallized solid raft floating on molten iron is propelled out of the ironmaking loop onto the first of two downstream steelmaking loops. In the first, a liquid slag is formed, primary decarburization is undertaken not with oxygen but rather with CO2 and H2O and the melt is desulfurized. The semi-product stream enters the third melt circulation loop, where open-channel decarburization is effected along with dephosphorization to yield a low carbon steel product. Alternatively, the melt leaves the last loop to irrigate a packed tower countercurrent to argon at around 100 mbar to continuously produce ultra-low carbon (ULC) steel.

Jan 1, 2003

By B. Madelin

Over the last ten years, Minemet Recherche and Metaleurop have used an approach in order to investigate and improve the operation of its Smelting furnace and its lead blast furnaces. This approach gives importance- to three complementary means of investigation : - Probing campains in the industrial furnace (temperature and gas analysis profiles), - Chemical and physical modeling (coke combustion, sinter reduction modes, flows patterns, ?.) , - Staged mass and heat balances or kinetic model. This allows to define the limits of operation of each blast furnace and to predict the influence of operating parameters on the furnace performances. For the zinc Imperial smelting furnace, the probing results show the existence- of both an Isothermal reserve zone at 1015ºc and a chemical equilibrium between ZnO and gas which makes possible the use of a practical model for heat and material balances. In particular, very good prediction on the influences of operating parameters can be made. On the contrary, for lead blast furnaces, the probing results show that the thermal and chemical equilibria are not reached. Consequently, classical models for staged heat and mass balances are not sufficient. The use of the other means allows then to characterize the specific influences of operating parameters on the thermal instabilities of these furnaces and their allowed limits.

Jan 1, 1990

Numerical simulation of the fluid flow and heat transfer has been carried out for a waste-heat boiler in an Outokumpu type copper flash smelter. In this boiler, SO2-containing off-gas flows into the waste-heat boiler radiation section at about 1350°C. A fraction of cooler off-gas from the electrostatic precipitator at about 200°C was recirculated into the radiation section, and a small amount of ambient air was leaked into the boiler from the bottom. The computational results show that the flow is strongly recirculating and distinctly three dimensional in most of the boiler, particularly in the radiation section. The hot off-gas cooled down rapidly after entering the radiation section due to radiation. The predicted flow pattern and temperature distribution were in a good agreement with laboratory models and industrial measurements.

Jan 1, 1995

By R. G. Henley

Mount Isa copper concentrate was combusted in a laminar-flow furnace. The conditions simulated those likely to be encountered in flames in flash smelters of the Outokumpu (air as oxidant) and INCO (oxygen as oxidant) types. The range of conditions studied was as follows: T 400-1400°C, 02 0-100%, SO2 0-95% for residence times up to 0.23 s. The distribution of sulfur, arsenic and lead between the particles and the gas phase was studied. Combustion was very rapid provided the concentrate was adequately dispersed, i.e., no agglomerates. The importance of the latter is discussed. It was possible to oxidize 80% of the sulfur present in the con¬centrate after only 0.1 s reaction time at 1000°C in an atmosphere contain¬ing 8.5% 02 and 12.5% SO2. Best volatilizations (90% of the As, 52% of the Pb) were obtained under localized conditions attained in an air-type flame. Average volatilizations were: air-type flame, As 50%, Pb 32%; oxygen-type flame, As 40%, Pb 30%. The substitution of oxygen for air reduced the arsenic volatilization. The products of combustion were mainly cuprospinel and cuprite; small inclusions of elemental copper were found in some of the particles. At high temperatures, there was a loss of copper due to vaporization of CU( g) CuO kg) (g)

Jan 1, 1983

By Jilai Xue, Jun Zhu, Baisong Li

"TiB2-C/C Function Gradient Materials (FGM) is used in cathode materials to improve aluminum wettability and melt penetration in aluminum electrolysis. In this investigation, FGM was tested for use as part of the cathode materials, where a 10 mm thick TiB2-rich layer was on the top as an Al-wettable surface, the TiB2-C layers in the middle as a gradient layer and the carbon on the bottom as a base. Electrical resistances ofFGM were determined in the temperature range of25- 9600C in argon atmosphere. The results show that the present of TiB2-C gradient layer can reduce the open porosity and the electrical resistance of the cathodes materials at elevated temperatures. The cathode samples after aluminum electrolysis usually demonstrates an increase in electrical resistance, but the application of FGM layer can compensate such an increase for certain extend due to less variation in porosity and lower the level of melts penetration.IntroductionCarbon is still used for aluminum reduction cathodes dominantly, but it has a poor wetting properties by liquid aluminum and the anode-cathode distance has to be kept about 4-5cm with an additional 1.3-2.0 V voltage drop [l]. TiB2 has better wettability by liquid aluminum with higher electrical conductivity and stronger chemical resistance to the electrolyte attack. And the wettability ofTiB2-C composites cathode on liquid aluminum can be also improved, while liquid aluminum can completely wet the cathode surface ifTiB2 content exceeds 27% [2-4]. However, during the process of TiB2-C composites cathodes preparation and aluminum electrolysis, the deformation by temperature variation or sodium penetration are great disparity between TiB2 and carbon due to their physical properties difference. This will accelerate the cathodes cracking and deterioration."

Jan 1, 2013

By J. D. Zhu, T. Ohmichi, H. Yasuda, S. Kashiwai, I. Ohnaka

"Since the casting process affects the properties of castings, its computer simulation has been greatly developed in the last decades. This paper presents our recent works, especially on mold filling simulation, because most casting defects such as porosities and inclusions that greatly affect the properties originate during mold filling. The first topic is the mold filling simulation with consideration of cavity pressure change during mold filling, including direct observation of flow phenomena with X-ray and pressure measurement. The second .one is the mold filling simulation in the lost foam process, in which gasification of polystyrene pattern and gas outflow through the coating and mold have been considered. The simulation can predict not only the mold filling sequences but also periodical vibration of the gas layer between the melt and pattern. The third one is the comparison of simulation of Al melt flow in a metallic runner and direct observation through a transparent mold, showing that the entrapped gas or inclusions is expelled ahead through the melt and its simulation needs very fine meshes. These examples show that the comparison of simulation and observation is very important to develop the numerical simulation further.IntroductionThe mechanical properties of castings are greatly affected by casting defects such as porosities and inclusions, and solidification structure. Although recently the structure simulation has greatly progressed [1-4 ], the application in plants is very limited, because the structure is mostly determined by chemical compositions and cooling rate, enabling us to estimate it from the structure of past similar castings without simulation.On the other hand, the casting defects often vary with each casting or time. Among the defects, porosities and inclusions are main causes to deteriorate the properties and mostly originate during mold filling. Therefore, a lot of efforts to simulate the mold filling and estimate those defects have been made in the last decades [l,5,6]. These efforts have been mostly to develop numerical techniques to solve the Navier-Stokes equation. However, the flow phenomena in molds have not been well understood, because the direct observation of the flow phenomena in mold is not easy. This means the accuracy of the simulation is still not clear."

Jan 1, 2000

By M. J. Adam

The Bureau of Mines is investigating the feasibility of partitioning complex sulfide minerals to simpler sulfide phases by sulfidation reactions. Such partitioning can afford opportunity to improve selective extraction of mineral constituents of value. This report describes research involving sulfidation partitioning of byproduct chalcopyrite concentrates from Missouri lead ore processing, and a Utah chalcopyrite concentrate from Cu ore processing. Small chalcopyrite samples were sulfidized with elemental S in glass capsules sealed after evacuating and backfilling with He, by heating for 1 to 24 h at specific temperatures in the range of 250? to 500? C, extending from below to above the boiling point of S (-4450 C).

Jan 1, 1987