Search Documents

By Sylvain Gouttebroze, Mohammed M'Hamdi

In a previous work, a small scale Bridgman furnace has been used to study silicon bi-grain crystallization at different cooling rate. This work expands the analysis by studying the mechanical interaction between the crucible and ingot during the solidification and cooling. The thermal model is based on a 2D-axisymetric heat-transfer model. The flux histories are then transferred to the ingot-crucible 3D-model. Anisotropic Elastic and Crystal Plasticity model are used to model the silicon deformation. Four different assumptions are applied to model the mechanical contact crucible-ingot and three grain misorientations are considered. The results show the strong impact of the alumina crucible contraction on the stresses and deformations in the silicon ingot.

Jan 1, 2015

By John D. Kinton

A patent is a right granted by the government to exclude others from making, using, selling, offering to sell, or importing a claimed invention. Once the right is granted, the patentee may use the U.S. Federal Courts to enforce that right. Reading a patent from a litigation perspective is quite different than reading it from a technical perspective. The Judge's interpretation of the claims will affect their scope, and likely the ultimate outcome of a patent case. Additionally, the patent right can be challenged. If done successfully, the patent can be rendered invalid or unenforceable. The likelihood of success, and well as the achievement of other litigation goals is often influenced by the forum where the litigation is initiated. Finally, patent litigation costs are significant, and will weigh heavily in the decision to file (or fight) a patent lawsuit.

Jan 1, 2006

By P. H. Scaife

The pyrometallurgy industry faces a series of environmental challenges, based on local, national and global issues. While local impacts continue to be important, national and global concerns with Sustainable Development, Greenhouse emissions, Acid Rain and water resources are key strategic drivers for the industry. The environmental problems of the industry are well known: emissions of sulphur dioxides and carbon dioxide, disposal of arsenic wastes, consumption of fresh water, fate and impact of minor components/trace elements in raw materials (whether conventional or complex, or wastes). Solutions to these problems require the application of Cleaner Production principles (waste minimisation, energy conservation, product design to enable ease of post consumer recycling), new technology and scientific studies to assess impacts of discharges. A number of opportunities, driven by environmental concerns, have also been identified

Jan 1, 1994

By Jae-Chun Lee

Di-2-ethylhexyl phosphoric acid (D2EHPA) is widely used for separating rare-earth elements. In commercial plants, rare-earths are usually stripped from loaded extractant streams using mineral acid, then precipitated as oxalates. Many rare-earth uses demand specific powder characteristics, which are obtained by secondary processing. This paper demonstrates the feasibility of combining the stripping, precipitation and powder processing stages, thereby achieving considerable savings. MEHPA solutions were loaded with yttrium, then emulsified with oxalic acid-HC1 solutions to precipitate yttrium oxalate, which was readily calcined to yttrium oxide. The precipitation kinetics and yield were sensitive to process conditions. The morphology and size of the yttrium oxalate powders varied with the concentrations of D2EHPA and oxalic acid, and the presence of SPAN 60, which affected nucleation, growth, and the emulsion characteristics.

Jan 1, 1992

By L. B. Tsymbulov

Sulphide melts formed in the course of smelting of nickel and copper-nickel feed (matte) actually are sulphide-metallic melts since sulphur contained in the melts is in deficiency with respect to metals. The level of metallization is rather relevant feature of sulphide melts and is widely used in calculating material and heat balances for pyrometallurgical processes. Despite of the above parameter? importance, the investigators have no single opinion on what should be understood under metallization level and the method of its determination. In the present study we present the results of our own experimental and theoretical researches that have allowed determination of some mechanisms of sulphide melts? crystallization. Based on the mechanisms revealed new scientifically justified approach has been offered for determining level of metallization of the components present in sulphide melts. It has been demonstrated that sulphur distribution between the melts is substantially different from generally accepted concept.

Jan 1, 2006

By Li Zhang

A novel green technology to recovery Titanium compounds from Ti-bearing blast furnace slag under the dynamic oxidation condition was developed and tested. Air was blown into the molten slag as oxygen resource through a lance during the dynamic oxidation process, in which six important results were found: (1) The TiC, (Ti2O3), Fe and (FeO) in the slag were oxidized; (2) The temperature of slag temperature rapidly increased; (3) The viscosity of slag decreased; (4) The coalescence, growth and drop of the metallic Fe droplets in the molten slag were carried out under an air agitation condition; (5) The dispersed Ti components were selectively enriched into the perovslite phase, and the perovskite phase could be selectively precipitate and grow. And also, the perovskite phase can be separated by the dressing method. The oxidation of molten slag gives off a large amount of heat, which helps chemical reactions proceed, improve the rate of chemical reactions, and promote the precipitation and growth of the perovskite phase. The features of the technique are clean, low cost and a great capacity to deal with a large quantity of slag. It was confirmed by experiments that the precipitation of the perovskite (CaTiO3) in molten slag is obviously affected by operation factors such as temperature, chemical composition, heat-treatment, additives and so on. The precipitating kinetics and mechanism of the perovskite phase from molten slag during the dynamic oxidation processes were also investigated.

Jan 1, 2006

By K. V. Sreenivas Rao

Solidification experiments have been conducted to study the effect of interface heat flux and air gap formation on cooling rate of the casting during solidification of Al-4.5wt%Cu alloy. The thermal history of the casting and mold during solidification is recorded using thermocouples connected to computer interfaced data logger. The measured temperatures in the mold are used as input to the IHCP (inverse heat conduction problem) algorithm for simulating multiple heat flux components at the boundary. It is observed that the filling effects induce spatial variation in the thermal field in the mold and casting regions and greatly influence the cooling rate of the casting. The study demonstrates the use of IHCP and in-situ measured thermal profile in analyzing the cooling rate and microstructure.

Jan 1, 2008

By A. K. Riihimäki

The description deals with duplex stainless cast steels and austenitic high molybdenum steels used in pumps for severe condition service. The main modem nitrogen alloyed duplex cast steels are presented in the ASTM standard A-890. Two grades of high molybdenum austenitic stainless steels there are presented in ASTM A-744 (-96) standard i.e. CN-3MN and CK-3MCuN. The latest and most corrosion- resistant stainless steel grade is AVESTA 654 SMO?. Avesta Sheffield the trademark owner has granted Ahlstrom Pumps license to produce the material. This new stainless steel as pump material for severe service has improved properties in the hydrometallurgy and electrorefining processes of metal and especially in the copper industry compared to duplex stainless steels. The paper deals briefly with the foundry process to manufacture high alloy stainless steel pump castings. The AOD-method (AOD= Argon Oxygen Decarburization) is an important prerequisite for the melting of low carbon, high chromium and molybdenum alloyed nitrogen steels. The properties of these steels are included. The main topic is the corrosion resistance of the above-mentioned pump materials in severe service. Results of short-time erosion and corrosion tests are discussed and compared with the results of plant tests. Practical results of pump materials performance in severe service for the copper industry are given. The new high alloyed cast stainless steel (main elements; Cr-24%, Ni-22%, Mo-7,3% and N-0,5%) has shown improved corrosion and erosion properties as process pump material in several severe service applications e.g. in the metal industry.

Jan 1, 1999

By A. V. Tarasov, V. M. Paretsky

"A mathematical model of the low-temperature (soft) nickel oxide reduction (SNOR) in a tubular kiln has been developed including an equation describing changes in the nickel oxide content of the solid material along the length of the kiln; an equation describing the changes in the content of reagents ensuring nickel reduction (i.e., hydrogen and carbon monoxide) in the gas phase along the kiln length; as well as the temperature along the kiln length. The kinetic relationships used for the development of the model had been determined based on experiments conducted specially for this purpose. Model investigations were conducted to determine the distribution of such parameters along the length of the kiln as the contents of metals oxides in the solids, partial pressure of hydrogen and carbon monoxide, variations of the temperature depending on the SNOR process conditions, including the kiln rotation speed. Based on the data obtained, a simplified regression model of the reducing roasting process was developed.IntroductionAt the SeveroNickel complex (Russia) a technology has been developed and is being introduced on a commercial scale for low-temperature (soft) nickel oxide reduction (SNOR) in tubular kilns.The SNOR process has a number of advantages, the main of which are the higher degree of metallization and higher chemical activity of reduced nickel oxide attributable to the lower fusion of the surface of the grains of reduced material due to lower process temperature (800-1000°C) and improved reducing ability of the gaseous phase. However, the fact that the process is conducted in a gaseous phase sets higher requirements to the consistency of its composition necessitating careful continuous monitoring and control of the main process parameters."

Jan 1, 2001

By David Tisdale, Phillip Mackey, Nagendra Tripathi, Matthew Kreuh, Pascal Coursol

Xstrata Nickel’s Sudbury smelter operation is based on fluid bed roasting of Ni-Cu sulphide concentrate, followed by electric furnace reductive smelting and Peirce-Smith converting to produce a Bessemer matte for electro refining, along with sulphuric acid produced from smelter gas. While the site dates back to the 1930s, the present smelter configuration has been operational since 1978, and currently has a nominal capacity of about 67,000 tpy of contained nickel and is investigating options to expand in future up to 85,000 tpy. As part of a review of plant capacity options, a new metallurgical model of the plant was developed in order to examine a number of processing alternatives. Based on the METSIM™ platform, the present model includes the ability to examine the impact of a number of plant parameters on potential plant performance including; for example, the following: percent of sulphur elimination in roasting, matte grade, degree of matte metallization, temperature, coke requirements, sulphuric acid production, CO2 emissions and overall energy requirements. The process model also includes a number of special features adopted; for example, approaches to effectively model the complex Ni-Cu-Co-Fe-S-O matte system. This paper provides a description of the model and gives an overview of the results. As well as presenting the results of the present study, the applicability of this modeling approach to pyrometallurgical systems in general is also briefly discussed in the paper.

Jan 1, 2009

By Ko-ichiro Ohno

It is recently recognized that the iron reduction and melting as well as the slag separation of a composite of granular iron ore and coal are completed in a very short period of about IO minutes when the composite is rapidly heated up to approximately 1673K. These phenomena are expected to be applied to a new iron-making process. The mechanism of iron ore reduction and iron-slag separation during rapid heating has not yet been revealed and the fundamental research has just started. Carburization of the reduced iron is regarded as one of the most important steps in this process. In the present work, the composite was prepared from four kinds of coal or graphite as a carbon source and electrolytic iron powder as a completely reduced iron ore. The temperature at which the liquid formation and iron carburization occurred was monitored. Direct observation of smelting reduction behavior was made by a confocal laser-scanning microscope combined with the infrared image-heating furnace to clarify the effect of molten ash on iron carburization. It was found that the meltdown temperature of composite became lower as the melting temperature of coal ash decreased. From the observed result, it was presumed that the liquid slag would act as an important media for the carbon transfer from coal to iron. The carburization mechanism during the smelting reduction was estimated as follows. When slag containing iron oxide melted down and contacted carbon, iron oxide in the slag was reduced and the formation of the metallic iron particle as well as the its carburization occurred simultaneously at the slag-carbon interface. Carburized iron particle was carried from slag- carbon to slag-iron interfaces due to the slag convection flow caused by the difference of the interfacial tension between the carbon-slag and iron-slag interfaces. Carburization of reduced iron could proceed with a repeat of the above-mentioned process.

Jan 1, 2003

By Michael J. Nicol

This paper summarizes some of the results of a study of the reactions involved in the Caron leaching process and identifies the roles of the major dissolved species in the kinetics of dissolution of iron alloy particles formed during reductive roasting. Using rotating disk electrodes and synthetic leach solutions, the reduction of water with the evolution of hydrogen was found not to occur on a dissolving iron surface under typical leach conditions. It has been established that the oxidative dissolution is governed primarily by a reaction involving reduction of Co(III) to Co(II) ions. The reduction of oxygen was also found to make a significant but largely indirect contribution to the kinetics of the dissolution process. The dissolution rates of various iron-nickel-cobalt-copper alloys which simulate the dissolving alloy particles in a Caron plant were measured in synthetic leach solutions under aerobic and anaerobic conditions. The initial dissolution rates of iron, nickel and the iron alloys were found to increase in the presence of thiosulphate, whereas the thiosulphate had a negative effect on the dissolution rates of cobalt and copper. It is shown that the eventual passivation of the iron occurs sooner in solutions rich in Co(II) ions. Whilst these conditions are present in the quench slurry, on-site measurements have shown that due to the very high concentration of reduced dissolved species, passivation does not occur until the slurry is strongly aerated. In the light of these fundamental findings, options for optimizing the rate of dissolution and minimizing the extent of passivation of the iron and iron alloys are discussed. Keywords: Ammonia, leaching, alloy, kinetics, passivation.

Jan 1, 2004

By R. S. Krarner

Fly ash, a by-product of coal burning power plants, poses a major problem for the utility industry since most fly ash must be landfilled. These quantities may represent as much as 20% of the total material going into landfills. A major problem with fly ash utilization is that although the ash consists of useable components, ash composition can vary depending on the types of coal burned and plant operating conditions. Ash is first characterized using SEM, image analysis, and chemical methods. Processing techniques were developed to separate ash into various components including cenospheres, magnetic spheres, carbon, and clean ash. These products are again evaluated for various utilizations before being used to produce valuable products such as mullite, activated carbon, fillers in plastics, and concrete.

Jan 1, 1994

By Roderick 1. L. Guthrie, Mei Li

"A mathematical model was developed to study the role of orifice shape in the detection of inclusions in LiMCA (Liquid Metal .cleanliness Analyzer) system. The fluid flow field within the ESZ was obtained by solving the Navier-Stokes equations. The trajectories of entrained particles were calculated using the equations for motion of particles. A numerical study of the effect of orifice shape on signal shape generated by inclusions passing through orifice showed that the signals in a parabolic orifice are gaussian in shape, while those in a cylindrical orifice are trapezoidal in shape. This signal shape difference needs to be taken into account when performing particle discrimination. Orifice shape influences also pass-through fraction of inclusions. Finally, a study of the orifice shape on critical conditioning currents suggested that as the polynominal coefficient of the parabolic orifice increases, the critical conditioning current, which is also the maximum operating current, decreases dramatically. These critical conditioning currents also increase as the fluid flow velocity within the ESZ increases. IntroductionThe presence of non-metallic inclusions in metals often leads to impaired mechanical properties such as a reduction in fatigue strength, and to processing problems such as tear-offs in deep drawing and increased breakage rates in wire drawing operations. Similarly, inclusions cause a variety of surface defects in rolled or extruded products.Prior to the development of the LiMCA system (1) at McGill University in the early 1980's, it was not possible to measure inclusions, in situ, in liquid metals. Compared with other techniques, such as sedimentation, filtration and metallography, which require considerable amounts of labor and time, the LiMCA method has the advantage of providing not only information on the volume concentration of inclusions, but also on the size distribution of inclusions immediately and quantitatively."

Jan 1, 2001

By P. V. Ananthapadmanabhan

Feedstock powders of metals, alloys and ceramics for thermal spray applications have to meet several specifications. Particle shape, size and distribution, powder flow characteristics and density are the important factors that need to be controlled, in order to ensure high spray efficiency and better coating properties. Thermal plasma technology can be effectively utilized to produce metal, alloy and ceramic powders for spray applications. The present paper describes plasma spheroidisation of commercially available aluminium powder and nickel-aluminium powder blend in a plasma reactor. Results show that the processed powder particles bear spherical morphology with excellent flow characteristics, which make them ideal for thermal spray applications.

Jan 1, 1997

By Masayasu Kawahara, Toshiyuki Kozuka

"Lorentz force, which has the functions of wave suppression and mixing control, is very useful for many metallurgical processes. In this paper, it is found that vertical Lorentz force which can change 'the gravitational force is able to modify the dispersion relation of the surface wave generated by gravity and also modify the instability phenomena on the interface so that the lower layer can be scattered into upper layers to realize the strongly mixed region.IntroductionIn metallurgical industries, recently, a new direction of process developments is required backed not only by severer operating conditions, e.g. small amount production, rapid refining, etc. but also by environment and energy problem. Because almost technologies in conventional processes have saturated, an innovative process, which can break the limits in the conventional processes, is now strongly required. Especially, controlling of mixing phenomena between two liquid phases is considered to be one of the most important technologies for the promotion of slagrnetal reaction, wave suppression, etc. On the other hand, electromagnetic forces which have various functions have been applied to many processes. And Lorentz force is able not only to suppress the wave motion of molten _metal surface but also to promote the mixing or separation of two liquids. In this paper, new controlling methods of mixing phenomena between two liquids are proposed, where a direct electric current and a stationary magnetic field are utilized. Vertical Lorentz force due to the interaction between the electric current and the magnetic field can modify the gravity force so that the dispersion relation of surface wave and the instability on the interface can be change to improve or develop the innovative processes(l,2).In case that a direct electric current is imposed on two liquid layers with a stationary magnetic field, Lorentz force of each layer becomes different due to the difference of electrical conductivity. If Lorentz force acting on the lower layer is stronger than that on the upper layer, resonance frequency of the wave motion on the interface due to the gravity can be shifted from the frequency of a outer disturbance to suppress the wave motion. And also, the lower layer can be scattered into the upper layer as liquid particles by an instability phenomenon."

Jan 1, 2000

By John ?gren, Martin Schwind, Henrik Larsson

"A new model for internal oxidation, as well as similar processes, has been implemented on computer. It is based upon a combination of random walk and cellular automata and is capable of treating 3-dimensional cases. To model diffusion, it utilises quantised units of matter. All steps of the process are included: nucleation, growth and coarsening. The effect of grain boundaries on diffusion as well as nucleation is taken into account. Further possible development is briefly discussed; especially the treatment of nucleation needs further consideration. IntroductionComplex diffusion-controlled processes may now be simulated on a routine basis when concentration varies along one co-ordinate only. One-dimensional simulations capture much of the information of interest but not all. For the case at hand, especially the spatial and the size distribution of precipitates, as well as the impact of grain boundaries, would be interesting information not accessible from 1-D simulationsSolving the full Fick-Onsager law in three dimensions does not seem feasible with the computers of today. In the model described in this article, random walk by quantised units of matter are considered. The model should be useful for a number of cases involving dispersed systems. With further development, it would indeed seem possible to simulate most types of phase transformations.Previous workWe have previously published two articles [1,2] on the new approach discussed in this work. In those articles we described the basic idea and showed, among other things, that very good agreement with an experimental concentration profile can be obtained, in a single-phase system, using independently assessed thermodynamic and kinetic data. Also, Schwind used the same random walk based concept to model coarsening [3]."

Jan 1, 2001

By Roger L. Williams

The Zinc Corporation of America Monaca smelter continues to use the St. Joe-developed electrothermic process for producing zinc metal and zinc oxide. As we enter the 1990s, the electrothermic process flexibility permits treatment of larger quantities? and lower-grade zinc-bearing recycle materials. A new sinter plant having one large sinter machine will increase sinter feed production required to meet our capacity target of 150,000 tons per year.

Jan 1, 1990

By James D. O, DeLa&apos

Multicomponent materials are common in nearly all areas of materials science and technology, yet the use of phase diagrams to represent these complex systems is hampered by the requirement of three or more dimensions for explicit graphical representation. In the present work, the "solid-modeling" capabilities of a computer aided design (CAD) system have been applied to the representation of three-dimensional phase diagrams. Relevant phase diagrams for a hypothetical quaternary eutectic system were constructed and used to demonstrate the capabilities of the technique. These capabilities lead to relative ease of phase diagram construction and improved access to qualitative and quantitative information. Results of this work are contrasted and compared to previous efforts toward computer ,representation of phase diagrams. It is concluded that solid-modeling of three-dimensional phase diagrams can be used to advantage in both education and research.

Jan 1, 1991

By T. Kamata, S. Takemoto, H. Takeuchi, M. Takayanagi, Y. Akahori, I. Jimbo

"A cooperative research work on the silver recycling process is underway between Matsuda Sangyo Co., Ltd. and Tokai University in Japan. Silver wastes treated here are mainly from photograph industries where the concentration of minor element is steadily increasing in the recent years. The waste materials are concentrated and the impurities are removed by evaporation and slagging. In this paper, the industrial practice of wastes treatment is introduced and the result of the laboratory studies on the removal of antimony and tin from the binary and ternary alloys will be discussed. Characteristics in the behavior of antimony and tin during the process are also discussed with the observation of practical operation.1. IntroductionPrecious metals such as gold and silver primarily come from mining practice and the byproduct in copper smelting. However, the recycled amount of these precious metals have been increased 1 along with the environmental restriction and the widely accepted idea of saving resources on the earth in the recent years.· Though the recycle process of precious metals are comparatively simple from other metals refining, the process has been getting more complicated as wastes treatment has to deal with more impurity elements which are intentionally added to the products. Among these additives, antimony is used in the film materials in the photography industries to suppress its inflammability. Tin is another concern ,that is also coming from photography wastes; These minor elements have become problematic during the recycle.The removal of these minor elements has been in operation at Matsuda through a traditional oxidation refinement process using a reverberatory furnace. However, the complexity of the charge makes the recycle process more tedious and troublesome. In order to investigate the minor element behavior in the complicated materials system during the silver recycling processes, a cooperative research work is undertaken between Matsuda Sangyo Co., Ltd. and Takai University in Japan. Silver wastes treated here are mainly discharged from photograph industries where the minor element contents such as antimony, tin and bismuth in those wastes are steadily increasing in the recent years. The liquid wastes containing silver are concentrated and then treated pyrometallurgically with solid wastes from other sources, where the impurities are removed ·by evaporation and slagging. The purpose of this study is to investigate detailed behavior of impurity elements in the silver. containing systems."

Jan 1, 2000