Search Documents

By Fangqing Yin, Qingyu Deng, Zhengfeng Qu, Mengjun Hu, Meilong Hu

Titanium bearing blast furnace slag, which contains 20%-30% TiO2, is a valuable secondary titanium resource. Based on the thermodynamics calculation effect of the temperature on the reduction of the slag in vacuum were studied at certain vacuum degrees. The results show that magnesium vapor and silicon monoxide vapor can be obtained at the condition of high temperature and low pressure. The purity of TiC increases with temperature increasing. When the temperature arrives at 1623K TiC can be obtained besides the reductant carbon. XRD result of the powder collected from the furnace cover show that magnesium and silicon in the titanium bearing BF slag leave the slag system during carbothermal reduction in vacuum. From the above it can be concluded that TiC can be obtained from the titanium bearing BF slag and silicon and titanium in the slag can be separated by carbothermal reduction in vacuum and acid leaching.

Jan 1, 2016

By Arpad E. Tonna

Recycling of materials from lithium-oxyhalide batteries is a complex task, since the dismantling of batteries is associated with many hazards. The electrolyte and the lithium anode metal are extremely reactive in the presence of water or water vapor. Therefore, the dismantling process is a complex task. In this process, the lithium battery is electrically discharged, then frozen in liquid argon, and cut into small size pieces. These are fed into an incinerator, where the unreacted portion of lithium metal, thionyl chloride, plastic separators and carbon paste are decomposed and burned to gaseous products. The aluminum, iron (steel) and nickel pieces are recovered as saleable scrap metals. The off-gases are scrubbed with an alkaline sodium carbonate containing solution. The clean gases are released to the environment. The particulate mater recovered from the scrub-suspension would be available as additive to the cement industry . The recycling of battery decomposition products improves the economic viability of the disposal processes. Work is in progress to develop safe handling, processing and recycling large size lithium batteries.

Jan 1, 1995

By Yongbin Yang, Meixia Cai, Yufeng Guo, Guanzhou Qiu, Tao Jiang, Jianjun Fan

"A series of sintering and metallurgical experiments were carried out to optimize the blast furnace burden structure in this study. The results indicated that the sinter disintegrated seriously with basicity around 1.4, and after this “turning point”, the sintering properties were improved gradually with the increase of basicity of sinter. Based on the results, an idea was put forward which focused on producing two different kinds of sinter with different basicity. Different with the original burden structure of 85% sinter with basicity 1.4-1.5 + 15% pellets, an alternative new BF burden structure was proposed by the following structure?44% sinter with basicity 1.05 + 44% sinter with basicity 1.87 + 12% pellets. This new alternative BF burden structure has been adopted by some steel plants.IntroductionIn recent years, conventional blast furnace (BF) process was put into operation to produce hot metal in “A” steel plant. “A” steel plant owns two sets of sinter strands at present. Because the sinter production capacity exceeds the actual requirements of BF, a burden structure with 85-90% self-made sinter + 10-15% purchased pellets is adopted to take advantage of the low–cost sinter. But the serious problems encountered with the BF operators are that the sinter disintegrated easily during transportation and storage process. Therefore, the rate of return fines is very high after sinter being screened."

Jan 1, 2012

By Tianzu Yang, Weifeng Liu, Lin Chen, Wei Chen, DUCHAO ZHANG, HUI XIAO

Carbonaceous refractory materials are widely accepted in many reducing smelting processes such as iron and ferroalloys. Oxidizing processes such as copper concentrate smelting traditionally use magnesia and/or alumina/silica refractory materials. The main objection to the use of carbon-based refractories as the exposed working lining in oxidizing applications is the potential for free oxygen to react with the carbon at high temperature, which could rapidly degrade the refractory lining. In 2013, Outotec and GrafTech conducted joint trials of a thermally conductive, carbonaceous lining for smelting copper concentrates in the Outotec® pilot-scale top-submerged-lance (TSL) furnace in Dandenong, Australia. This testwork had two equally important goals; to demonstrate the ability of carbon refractories to withstand oxidizing process conditions, while ensuring that neither furnace operating conditions nor process stability were negatively affected by the refractory material. The paper discusses the input parameters of the trials, key observations during the testwork program, and the results and conclusions from both process and refractory design standpoints.

Jan 1, 2016

By Mikula Adolf

Lead-tin solders are commonly used in electronic packaging due to their unique combination of electrical, chemical, physical, thermal and mechanical properties. Since it is known that lead and lead containing alloys cause great environmental concern and health hazards it is necessary to replace lead in solder materials. Besides the environmental concerns new technologies in electronic packaging require new and improved solders. In most cases the new solders will consist of temary or quarternary alloy systems, the main component will be tin or indium and the second element could be bismuth. silver, copper and gold and to improve certain properties a third element will be added. For a third element zinc, nickel, antimony and aluminum can be considered. This report will concentrate on solders containing zinc as an environmental safe. element.

Jan 1, 2003

By J. A. Brierley

A biooxidation-heap pretreatment process was field tested to evaluate enhancing gold recovery from a preg-robbing sulfidic carbonaceous ore. Newmont Gold Company&apos;s Gold Quarry sulfidic carbonaceous ore was inoculated with an iron-grown culture of Thiobacillus ferrooxidans to form a 495 ton test heap. Biooxidation was conducted for a period of 100 days. The most active period of biooxidation occurred during the first 40 days of pretreatment? About 35 to 40% of the sulfide was oxidized. The extent of biooxidation was considered good as the ore particle size was relatively large 58% >1?9 cm (&apos;/< inch). The larger particle size ore limited the extent of bacterial activity. The field test demonstrated the ability to conduct biooxidation in a small pilot test heap. Thiourea was evaluated for extraction of gold from the biooxidized preg-robbing ore.

Jan 1, 1995

By Åke Saudström

An EAF dust sample generated in a scrap based steel mill was treated by a combination of hydro- and pyrometallurgial techniques. The EAF dust contained mainly ferritic spinels forming solid solution phases according to the general chemical formula (MnxZnyFe1-x-y)Fe2O4 and other oxide phases such as ZuO. CaO and Ca2Fe2O5. The EAF dust was first treated by hydrochloric acid leaching at p8=3 which dissolved 63% of the zinc. The pyrometallurgical treatment of the leaching residue was studied using an induction heating system to simulate some important operations of EAF smelting of the residue in combination with steelmaking. The leaching residue was mixed with carbon powder to obtain a mixture with 52.1% ZnFe2O4 and 175% carbon. The mixture, scrap, and slag former were charged together in a crucible and heated to attain a melt temperature around 1650°C. The effects of different amounts of mixture on the zinc balance and iron recovery were examined. Based on the test results, suggestions are made for the EAF recycling procedure of the leaching residue.

Jan 1, 2003

By Jerold L. Johnson

Remediation of small-arms firing ranges is being investigated by the Naval Civil Engineering Laboratory and the U.S. Bureau of Mines. Scheduled closures of military installations, as well as the management of active ranges, require the development of methodologies for heavy metals removal to prevent their entering the surrounding environment. The impact berms contain high concentrations of metals, and the soil and vegetation surrounding the berms were found to have slightly elevated levels. The heavy metals characterized are in the form of whole bullets, a wide size distribution of free fragments, smeared lead on the surface of the soil grains, and very finely attached particles. Gravity beneficiation can remove liberated metal contamination effectively. Weak acetic acid leaching shows promise in lowering the final metal contamination to allow the ,soil to pass the Environmental Protection Agency&apos;s (EPA) Toxicity Characteristic Leaching Procedure (TCLP) criteria.

Jan 1, 1993

By A. Kar

A mathematical model is presented for pure titaqium deposition from titanium tetrabromide on a stainless-steel (SS 304) substrate. Five three-dimensional, transient, and nonlinear partial differential equations are used to account for the diffusion of various species inside the deposition chamber and the thermal decomposition of titanium tetrabromide, titanium dibromide, and titanium monobromide at the surface of the substrate in order to determine the thickness of the titanium film deposited on the substrate. The effects of various process parameters on the deposition and shape of titanium films are examined, and under certain conditions, the deposited titanium films are found to have volcanic profiles.

Jan 1, 1992

By Z. M. Zheng

Cyclic voltammetry, potential step, and ac impedance techniques were applied to study the electrochemical reaction of arsenopyrite in chloride solutions. The relationship between anodic current density and time in potential step measurements indicates that the oxidation of arsenopyrite is irreversible. The results of the constant potential coulometry show that the stoichiometric factor of the total electron involved in the overall reaction is 14. It is proposed that the dissolution of arsenopyrite is retarded by coverage of sulfur produced in the reaction as an intermediate product. The measured results of ac impedance strongly support the proposition. The proposed reaction mechanism also explains satisfactorily the charging current density and Tafel slopes measured in potential step measurements.

Jan 1, 1995

By Dimitrios Fillippou

Magnesium hydroxide is used in a number of industrial applications, from the neutralisation of acid effluents to the production of pharmaceuticals. High-quality magnesium hydroxide powders can be produced by hydrating slow-reacting magnesia in dilute magnesium acetate solutions. The process of magnesia hydration shows many similarities with a typical hydrometallurgical leaching operation; however, its kinetics are crucial not only for process design and control, but also for the production of powders with a desirable particle morphology. This article shows the results of an experimental work whereby industrial heavily-burned magnesia powders were hydrated in 0.01 to 0.1 mol/L magnesium acetate solutions at temperatures ranging between 333 and 363 K. Examination of the magnesium hydroxide produced and the analysis of the kinetic data suggest that the hydration of heavily-burned magnesia in magnesium acetate solutions is a dissolution-precipitation process controlled by the dissolution of magnesia particles. The activation energy was estimated to be 60 kJ/mol, while the reaction order with respect to magnesium acetate concentration was found to be about one.

Jan 1, 1999

By Marcelo B. Mourao

Interactions of carbonaceous materials with liquid Fe-C melts have been investigated experimentally by determining the volatile yield due to rapid devolatilization (Flash Pyrolysis) and rates of dissolution at temperatures ranging from 1623 to 1873 K. The volatile yield increased with increasing the temperature. The comparison of results of different types of carbonaceous materials was possible by expressing the volatile yield in terms of Enhancement Factor, fE. The rates of dissolution of spectroscopic graphite and an industrial coke seemed to obey the correlation for natural convection under turbulent conditions. The experimental data for the graphite suggested that the rate of dissolution was controlled by the mass-transfer in the liquid boundary layer adjacent to the solid sample. The value for the empirical parameter correlating the dissolution coefficient and the operating variables was found to be 0.19 which was close to that reported in the literature. The comparison of the results obtained for the coke samples with those for the graphite revealed that the impurities and the porosity of the samples can effect the dissolution rates.

Jan 1, 1992

By S. J. Buckler

Many chemical and metallurgical processes use submerged gas injection to increase contact area between gas and liquid phases in order to promote faster overall reaction or refining rates. The total interfacial area produced by gas injection through lances, nozzles or tuyeres is both an important design parameter for new vessels and a measurement for estimating the maximum processing capacity of existing equipment. Estimating total interfacial area from submerged injection into industrial pyrometallurgical vessels from existing knowledge is a problem with two aspects. The first difficulty is the difference in behaviour of cold (aqueous) and hot (molten metal) systems, implying that existing models and correlations of gas-liquid behaviour developed in low temperature systems are not necessarily appropriate for estimation of high temperature behaviour. The second difficulty is the issue of scale-up of correlations from laboratory to industrial sized vessels. The work presented in this paper is part of an ongoing experimental investigation, at the GK Williams CRC for Extractive Metallurgy, to quantify the total gas-liquid interfacial area available in pyrometallurgical vessels using chemical measurement methods. The effects of three operating variables, injected gas flow rate, nozzle diameter and nozzle submergence, on total interfacial area are quantified in a IOOL aqueous system - the first stage of a three stage process in examining the implications for scale-up of high temperature, medium-scale results are discussed. The results of work at high, injected gas flow rates (up to 500/min) show that the submerged Froude number is not sufficient for use as the sole variable in a predictive model of total interfacial area. Further work is being undertaken to identify other dimensionless variables that will better represent the gas-liquid characteristics in submerged injection that influence the formation of total interfacial area. The second and third stages of the experimental investigation involve measuring the total interfacial area in a large-scale (1000L) aqueous sodium sulphite and small-medium scale molten metal baths.

Jan 1, 2002

By S. Mondon

Hibi Smelter which is a Copper Smelter lining a blast furnace, produces 2,700 metric tons of anode copper per month. Generally, in a copper refinery, arsenic and antimony are considerably troublesome impurities. With regard to the elimination of antimony, Hibi Smelter has two handicaps described as follows. (1) Smelting under the slightly oxidizing atmosphere in the blast furnace. (2) Recycling the converter slag to the blast furnace after cooling. Therefore antimony and arsenic, mainly antimony, elimination tests, in which the alkaline flux was injected through the two tuyeres in the blowing stage, were carried out in the rotary anode furnace. Antimony and arsenic were respectively removed more than 90 96 from the molten copper, and their high eliminations are discussed by application of the transitory and permanent reaction model with the flux injection, which was presented by T. Lehner.

Jan 1, 1983

By I. M. Ritchie

Cyanide owes its great success as a lixivant for gold to the great strength of the Au-CN bond. A replacement for cyanide must similarly be a strong complexant for gold (I) or gold (III). The various alternatives are briefly considered and it is concluded that only thiosulfate has a reasonable chance of replacing cyanide as a relatively non-toxic lixivant at the present time. However, there are considerable technical problems to be overcome before thiosulfate can be considered to be a realistic alternative to cyanide. Firstly, the leaching of gold using aerated ammoniacal thiosulfate with copper as a catalyst is a complex process which needs to be understood and controlled carefully in order to achieve maximum recoveries with minimum reagent losses. Secondly, there needs to be an option similar to the CIP process for recovering and concentrating the dissolved gold thiosulfate complex from pulps produced in the processing of low grade gold ores. The prospects for overcoming these technical&apos; challenges are evaluated and discussed.

Jan 1, 1998

By Denise Corrêa de Oliveira

Common dry batteries use zinc as the negative electrode. Producers commonly use additives such as mercury to prevent corrosion and to increase the mechanical resistance of the zinc anode. Alkaline batteries also contain it, as an anti-corrosive agent. When mixed with the common municipal solid waste, heavy metals as zinc and mercury pollute soil and ground water supplies, moving to the food-chain and affecting human health. Due to these possible damages, this kind of waste must be properly disposed, or recycled. Thus, even in low amounts (ppm) in batteries, mercury has to be eliminated or, at least, its content should be reduced. This work presents the use of pyromettalurgical processes, to reduce mercury content and recover zinc. The tests involved batteries treatment at temperatures from 300° to 1000°C. Mercury is eliminated up to 650°C, and zinc is evaporated at higher temperature treatment. C

Jan 1, 2001

By V. D. Tathavadkar

Chromite ore is of immense importance for the extraction of metallic chromium and chromium chemicals. The mineralogy and crystal structure of chromite phase are therefore important part of our investigation on the extraction chemistry of chromium species. In this investigation, we have studied the effect of the processing parameters, i.e., the temperature and the oxygen potential on the microstructure and composition of mineral phases formed in the Cr2O3 ?Al2O3 -FexOy -MgO system. In particular the importance of the spinodal decomposition reaction is emphasized in the extraction of chromium as sodium chromite and sodium chromate. Experiments were carried out in order to study the differences in the crystallography of different chromite minerals. Phase equilibria in natural chromite minerals were investigated by calcining chromite mineral in air, argon, and 5% hydrogen + argon atmospheres over a temperature range from 200 to 1200 °C. The effect of the oxygen partial pressure and temperature on the phase constituents of the calcined product has been discussed. The microstructural changes were examined using scanning electron microscope (SEM) and the changes in elemental composition in different phases were analysed by electron probe micro analyser (EPMA). The results obtained from EPMA studies were used to calculate lattice parameter of the spinel lattice, and these values were compared with the values obtained from X-Ray powder diffraction data. On the basis of the experimental data, the mechanism of the spinodal decomposition of complex spinel phases is described under the influence of oxygen partial pressure and temperature.

Jan 1, 2000

By J. V. Atwood

The U.S. Bureau of Mines has developed a novel Double Membrane Electrolytic Cell (DMEC) that exhibits unique features for recycling contaminated metals and metal alloys. The DMEC incorporates two anionic ion exchange membranes, separating anodic and cathodic regions of the cell. The ion exchange membranes prevent significant transport of unwanted cationic impurities to the catholyte from the impure anolyte while the anion/cation balance in cell compartments is maintained through the free movement of anions between compartments. The membrane barrier makes it possible to electro refine highly contaminated materials or to electrowin from solution while utilizing alternate anode reactions. Sinceanolyte and catholyte cross contamination has been eliminated, premium cathode products are produced. The DMEC has been tested at bench, pilot, and commercial scales. Configuration of the DMEC, cell operation, scale, up efforts, and significant design factors are discussed. Two separate recycling investigations utilizing DMEC technology are presented. The first investigation examines recovery of high purity cobalt and nickel from severely contaminated super aIloy scrap. The second involves? upgrading contaminated cobalt in the U.S. Government&apos;s National Defense Stockpile. Capital and operating costs for both potential applications are presented.

Jan 1, 1995

By Robert E. Moore

Synthetic spinel is proving to be a highly effective refractory for specific applications, but its cost limits applications. Formation of spinel from a raw material such as diaspore or bauxite could provide a suitable and less costly starting material. In the study reported here, finely ground (-325 mesh) diaspore from Missouri and bauxite from Guyana and China are combined with hardburned MgO (-325 mesh) in appropriate proportions to yield spinel and spinel with secondary phases. A classical sintering and creep study was completed, accompanied by a microstructure study to determine completeness of the reactions and morphologies of the reaction products.

Jan 1, 1991

By W. K. Collins

Engineered Scavenger Compounds (ESCs), developed by the U.S. Bureau of Mines, are a novel class of compounds that can selectively recover a desired element from a solid or molten alloy. Lithium titanate (Li2Ti3O7 or L&apos;20-3T&apos;02) is being used as an ESC to recover lithium (Li) from Aluminum-Lithium (Al-Li) alloys. X-ray diffraction measurements have shown that lithium titanate undergoes a phase change from an orthorhombic structure to a hexagonal structure. This change is due to the incorporation of Li in the matrix of the material and the effect of temperature. Although both are metastable, the hexagonal phase that forms during the scavenging of Li from Al-Li alloys appears to be the more stable phase. Recovering Li from the ESC by electrodeposition does not cause the structure to revert to the orthorhombic phase. Both the orthorhombic and the hexagonal structures of Li2Ti3O7 have similar scavenging capacities for Li. This paper proposes a new mechanism for the phase transformation.

Jan 1, 1993