Search Documents

By O. P. Pandey, Rama Arora, Gurmel Singh, Suresh Kumar

The tribological behavior of Dual Particles Size (DPS) rutile reinforced LM13 alloy composite was investigated under varying applied pressure from 125 kPa to 625 kPa at a constant sliding speed of 1.6 m/s. In the present studies, 15 wt.% of rutile particles of different sizes (50-75 μm and 106-125 μm) are reinforced in the Al-12Si alloy (LM13) by liquid metallurgy route. Microhardness of the prepared samples was measured in different phases. Microstructure, wear mechanism and surface morphology of the wear surfaces and debris was observed under optical and scanning electron microscope. The change in wear behavior has been explained with reference to the observed EDS analysis of the wear track and debris. However, an interesting change in wear feature, mild to severe wear transition at critical pressure was noticed in wear behavior of the composite. The Al-DPS composite has immense potential to be used as a component material for tribological applications.

Jan 1, 2015

By Steven Wright

The reduction of a slag produced 6om the recycling of lead batteries was studied in a kilogram scale laboratory investigation by reacting with graphite at temperatures of 1180 and 1200°C. Simultaneous reduction of PbO, Fe203, Sb203 and As203 occurred with the Sb and As reporting to the metal while the lead content in the slag was above 2 wt%. The Sb and As distributions between metal and slag were strongly affected by temperature and slag oxidation state. The rates of reduction of PbO and Sb203 increased with increasing slag basicity and temperature and decreased as the PbO content in the slag decreased. The reduction rate of PbO from these slags was similar to other industrial lead slags at the same CaO/SiO2 ratio and temperature. The implications of the behavioural similarities of the antimonous slags during reduction with carbonaceous reductants and other lead slags are briefly discussed.

Jan 1, 1994

By Tobias Dubberstein, Hans-Peter Heller

The viscosity of Fe-Cr-Mn-Ni TRIP/TWIP (Transformation Induced Plasticity, Twinning Induced Plasticity) steel with varied nickel content is investigated using a vibrating finger viscometer. The viscosity of the melt is calculated from the change in power input in the field coil by an immersed finger into the liquid steel to maintain a constant peak-to-peak amplitude of the sine wave of oscillator compared to the idle state. Nickel content in steel is varied from 3 wt% to 9 wt%. The dynamic viscosity (η) at 1600 °C for 3 wt% Ni is 3.73±0.14 mPas, for 6 wt% Ni 3.50±0.03 mPas, and for 9 wt% Ni 3.93±0.09 mPas. There is a kink from low to high nickel content in viscosity values of Fe-Cr-Mn-Ni alloys. This phenomenon can be explained by a change in coordination number in the melt, as reported for Fe-Ni binary system in literature. The availability of viscosity data delivers relevant input to model free fall atomization processes of FeCrMnNi alloys.

Jan 1, 2015

By Zhigeng Xu

Pressure leach of a Yunnan marmatite concentrates with adding coal as the elemental sulfur disperser was investigated. The experimental results show that the coal with carbon content higher than 70% is incapable of dispersing elemental sulfur from minerals and cannot improve the leaching of zinc. The coal with low carbon content (lignite coal) can act as excellent sulfur-disperser in the pressure leaching at 423K. The mechanism of lignite coal as sulfur disperser was further discussed by ultraviolet, infra-red spectrum and mass spectrum.

Jan 1, 2008

By Ralph H. Nafziger

The feasibility of smelting a Ni-Co-Cr-bearing laterite ore from southern Oregon was evaluated by the Bureau of Mines. The objective was to prepare a master alloy for subsequent stainless steel production. A mixture of the ore with suitable reductants and fluxes was smelted in a 50-lb-capacity single-phase ac electric furnace under sub- merged arc conditions. The smelting tests produced a metal in which most of the nickel was concentrated. High-chromium recoveries required an excess of carbon. The resulting metal alloys contain sufficient nickel for some stainless steels. Ferrochromium additions would be required to attain suitable chromium levels. This research was conducted under the Oregon Metals Initiative in cooperation with Walter B. Freeman.

Jan 1, 1993

By Yanhui Liu, Xuewei Lv, Chenguang Bai

A thermodynamic model for determining the surface tension of molten slag by considering the surface tension and molar volume of the pure oxide component, and their ionic radii was extended to the slag bearing high TiO2 (varying from 80 to 67%) at 1973 K. The iso-surface tension curves for the FeO-TiO2-Ti2O3 ternary system at 1973 K are almost parallel to the FeOTi2O3 line. TiO2 plays a role of surface-active solute, and its surface-active effect is attenuating with increasing the TiO2 content. The iso-surface tension curve shifts away from the TiO2 corner, indicating that the surface tension of the ternary slag decreases along with the addition of SiO2. The reasons include the addition of SiO2 with lower surface tension and the decrease of the total ion moment at the surface. Both CaO and MgO can bring about that the iso-surface tension curve shifts towards the TiO2 corner, indicating that the surface tension of the ternary slag increases along with the addition of CaO or MgO. CaO has a more pronounced effect on increasing the surface tension of the ternary slag than MgO at an equimolar amount addition. The increase of the surface tension results from both the compositional change and the variation of the slag structure.

Jan 1, 2015

By C. A. Young, J. D. Miller

Adsorption isotherms previously determined by in-situ Fourier transform infrared/internal reflection spectroscopy (FT-IR/IRS) for oleate adsorption at calcite and fluorite surfaces near pH 9 and at various temperatures are compared. Results indicate that, at both mineral surfaces, chemisorption occurs at equilibrium concentrations below approximately l x l0-5 M oleate while calcium dioleate surface precipitation occurs at higher equilibrium oleate concentrations. The extent of chemisorption at the calcite surface is 3 to 5 times less than that at the fluorite surface while the extent of calcium dioleate surface precipitation on calcite is nearly a magnitude larger than that on fluorite. However, for both minerals, surface precipitation decreases with increasing chemisorption. Contact angle measurements and flotation recoveries show the hydrophobicity of fluorite to be greater than that of calcite at each of the temperatures and oleate concentrations studied. Significant differences are noted only in the chemisorption region. Unlike calcite, the hydrophobicity of fluorite was sensitive to the presence of oxygen in the system. Multichannel Laser Raman Spectroscopy (MLRS) showed this behavior was caused by the double-bond reactivity of adjacent chemisorbed oleate molecules and subsequent formation of an epoxide/polyether complex at the fluorite surface. Such a reaction product could not be detected at the calcite surface. These differences in adsorption density, hydrophobicity, and polymerization behavior are discussed in terms of the intrinsic surface properties of the minerals.

Jan 1, 1999

By May Nyman

Due to the vast diversity of chemical media in which metal separations are executed, a wide range of ion separation materials are employed, This ,results in an ongoing effort to discover new phases with novel ion exchange properties. We present here the synthesis of a novel class at, thermally and chemically stable microporous, niobate-based materials. Ion exchange studies show these new phases are highly selective for Sr2+ and other bivalent metals.

Jan 1, 1999

By Michael Altepeter

Big River Zinc Corporation, located in Sauget, Illinois, operates a neutral leach residue circuit. The residue produced in the circuit is sold to lead smelters for subsequent recovery of valuable metals. A research program was initiated several years ago to find a means of treating the residue at Big River Zinc to recover the valuable metals. The Ausmelt submerged lance reactor was selected as the best alternative for the first step of the process. Pilot scale tests were conducted at Ausmelt's facilities in Melbourne, Australia. Separations were excellent. 99%+ of the Zn, Pb, Cd, and Ag contained in the residue reported to the oxide fume. 99%+ of the SiO2,, Fe, Mg, and Ca in the residue reported to the slag which passed the EPA TCLP test. Subsequent leaching of the oxide fumes and purification of the leach solutions using conventional procedures produced solUtions suitable for zinc electrowinning and an upgraded lead sulfate cake for sale.

Jan 1, 1992

By Yuan She, Qihang Liu, Keng Wu, Hailiang Ren

By observing different coal char’s microstructures and microscopic morphologies during the coking process, the characteristics of COREX coal char’s microstructure and properties were analyzed. MCRI and MCSR were used to respectively describe the reactivity and the strength after reaction of coal char, with those of BF’s coke for reference, and then the physical meaning of MCRI and MCSR were given. MCRI and MCSR were determined by the composition of coal char. For the two kinds of COREX coal, the formula to forecast the hot performance of coal char was set up by making a multiple linear regression between the hot performance and microstructure of the coal char at 1100℃, and the predictive values of coal char’s hot performance at 600℃, 800℃ and 1000℃ coincided well with the measured values.

Jan 1, 2015

The Kaldo furnace smelting technique was developed for oxygen steel production by the late Prof. Bo Kalling, Domnarvet, Sweden. Development started in 1948, and production in 1956. Five million tons of steel were produced in TBRC's in 1973. Mainly due to high TBRC maintenance costs, the steel industry now prefers non-rotating converters. In non-ferrous metallurgy, however, qualified new applications of the TBRC technique have been realized or are being considered. Inco, Canada, succeeded to convert nickel matte to metal in the Domnarvet pilot plant in 1959, and have now installed a commercial plant in Copper Cliff. La Metallo-Chimique, Belgium, has pioneered secondary copper smelting and refining in the TBRC, operating plants in Beerse, since 1968, and Alton, U.S.A. Peko-Wallsend Ltd., Tennant Creek, Australia, was faced with the problem of producing saleable blister from concentrates containing 1.5-2.0% Bi. The flash smelting matte, containing 0.2% Bi, could not be refined to an acceptable limit of 0.03% Bi in the blister copper in a Peirce-Smith converter. Tests at Domnarvet indicated that a TBRC would achieve satisfactory bismuth elimina- tion. Two TBRC's were installed in Tennant Creek and operated for 14 months during 1974-75. The problems encountered and how they were over- come are described. Further TBRC applications have been studied in Sweden.

Jan 1, 1976

By Zachery Zanetell

Flotation circuit performance has become increasingly more challenging due to the complexity of available ore sources. To optimize value mineral recovery, the mineralogical composition of the ore should be evaluated and understood. Utilizing a variety of mineralogical and analytical tools, flotation processing challenges can be overcome and potential limitations understood. In this paper, several case studies will be discussed in terms of the value that has been provided through the use of mineralogical analysis to optimize flotation performance.

By Bo Liang, Hongmin Zhu, Kai Huang, Shafiq Alam

A new approach of recovering platinum and palladium from electronic wastes by hydrochloric acid leaching followed by selective adsorption on low-cost and environmentally benign biomass sorbent prepared from easily available agriculture waste is suggested. The obtained adsorbents were prepared by a combination of chemical modification and hydrothermal carbonization process with (NH4)2C2O4. It was found that the maximum adsorption capacity of hydrothermal carbonized garlic peel for Pt( ) and Pd( ) was 1.64 and 0.42 mol/kg respectively. The Langmuir adsorption isotherm was applied to describe the adsorption process. Kinetics of the Pt( ) and Pd( ) ions adsorption was found to follow pseudo-second-order rate equation. The adsorbents were examined by scanning electron microscope (SEM), and Fourier transform infrared spectroscopy (FT-IR). Based on the characterization results, a possible mechanism of Pt( ) and Pd( ) ions adsorption with the hydrothermal carbonized garlic peel was proposed. This study provides a promising adsorbent with efficient adsorption property for platinum and palladium recovery from the leach solution of electronic wastes.

Jan 1, 2016

By J. T. I. Poijärvi

The smelter off-gas cleaning and the weak acid treatment at Outokumpu Harjavalta Metals Oy are presented and described in this paper. The smelter consists of the copper and nickel smelters and the acid plant of three separate acid plants two of which are double contact and one single plant and of one liquid sulphur dioxide plant. The preliminary cooling and flue dust separation of the smelter off....,gases from the copper ?and nickel flash smelting furnaces and converters? in the waste heat boilers and in the hot electrostatic precipitators are described. The final cooling and cleaning of the gases in the scrubbers at the sulphuric acid plant and the treatment of the weak acid in the vacuum and in the submerged combustion evaporators for the removal of impurities are presented as well as the treatment of the condensates from the evaporators. The attention is paid to the generation of sulphur trioxide in the smelter off-gas.and to the treatment of that in the weak acid bleed-off and to the utilization of the treated acid.

Jan 1, 1992

By I. Gaballah

Spent hydrorefining catalysts may contain 4 to 6 % of COO and/or NiO, 8 to 16 % of Moo3 and up to 10 % V205 generally supported by alumina. Raw samples are roasted in order to eliminate carbon, sulfur and hydrocarbons contained in the spent catalysts. The roasting optimum temperature and time are 500 "C and 7 hours. Selective chlorination of roasted samples with Cl2 + air, Cl2 + N2 and Cl2 + CO is investigated in order to recover the valuable metals. Depending on the chlorination it is possible to recover more than 80 % of the Ni and Co about 95 % of the Mo and up to 80 % of vanadium compounds. Cobalt and nickel chlorides are obtained by leaching the chlorination residues' by acidified water. Molybdenum and vanadium chlorides and/or oxychlorides are obtained by selective condensation from the vapor phase. The chlorination of the catalyst support, Al2O3, can be limited to less than about 5 %. Besides the reaction temperature and time, the oxygen partial pressure of the chlorinating gas mixture appears to be the key factor for the reactions' selectivity.

Jan 1, 1993

By J. Szekely, S. Rhee

"A mathematical formulation has been presented to describe heat and fluid flow phenomena in CVD operations. In the statement of the problem, which included consideration of plasma enhanced CVD systems, emphasis was placed on identifying the parameters which play a key role in determining the rate and the spatial uniformity of the deposition process. This was done both through the appropriate dimensionless groups and by presenting an extensive set of computed results. The main conclusions that may be drawn from this work are that the deposition rate will be inherently non-uniform for atmospheric CVD systems; this may be somewhat ameliorated by inclining the susceptor or changing the vessel contours. Operation at greatly redeced pressures and for PECVD systems will give a much more spatially uniform deposition rate.1. INTRODUCTIONIn recent years, there has been a growing interest in chemical vapor deposition techniques for the preparation of thin films for semiconductor, photovoltaic applications and for coatings in general, as evidenced by numerous journal articles and symposium proceedings devoted to this topic (1-6). An interesting variant of this technique is to perform the deposition in a plasma or glow discharge at low pressures because this technology obviates the need for the thermal decomposition of the precursor at the substrate surface and permits operation at greatly reduced temperatures (7-10).By far, the largest portion of the reported work dealing with both these aspects of the technology has been concerned with the characterization of the deposit, quite properly so. However, in more recent times it has been realized that the transport aspects of these processes are also deserving of attention because the understanding of heat flow, fluid flow and diffusional phenomena may provide the key to the solution of problems associated with obtaining uniform deposits and the proper scaling of laboratory measurements in order to design industrial CVD systems."

Jan 1, 1986

By Hitoshi Iijima, Fumitaka Tsukihashi

"Fine powder of tantalum is used as materials of electric condenser. It is important to control the distribution of particle diameter of tantalum fine powders for the commercial use. In this study, fine powders of tantalum were produced by reducing tantalum chloride vapor with hydrogen gas at 1673 and 1773K. The tantalum chloride vapor was reduced with hydrogen and the produced fine particles of tantalum were collected to observe the distribution of particle diameter. The effects of reaction temperature, partial pressure of hydrogen gas and vaporization temperature of tantalum chloride on the distribution of particle diameter and reaction efficiency of reduction were determined. The mechanism of reduction reaction of tantalum was discussed.IntroductionThe ultra fine powder shows various different physical properties from that of bulk materials. Therefore, the application of ultra fine powder to various fields such as magnetic material, electric material, catalyst, etc is anticipated. The control of shape of powder, size distribution, property of agglomeration, purity is required for the practical use of ultra fine powder. Although the ultra fine powders of ceramics are produced by various methods, the ultra fine powder of metals are produced by the evaporation in gas atmosphere, plasma evaporation process, chemical vapor deposition process, and reduction and precipitation in liquid phase depending on the metal and productivity. The chemical vapor deposition process has features that pure metal powder can be obtained and the control of the distribution of powder size is easy. [1,2,3,4,5]"

Jan 1, 2000

By Sheng-li Wu, Guo-liang Zhang, Bo Su

One of the major challenges for the Canadian Gen IV Super-Critical Water-cooled Reactor (SCWR) concept is the selection of fuel cladding materials. The Canadian SCWR concept will operate at a core outlet temperature of 625 oC and 25 MPa of pressure with peak cladding temperature reaching as high as 800 oC. Corrosion resistance is an important factor for material selection. Austenitic stainless steels that contain Cr contents greater than 18 wt.% are generally considered to provide adequate corrosion resistance. In this work, the pressure dependence of the corrosion of austenitic stainless steel 310 containing 24 wt% Cr is assessed at 625 C for exposures of 1000 hours to evaluate the suitability of superheated steam as a surrogate for supercritical water at 25 MPa. Transmission Electron Microscopy (TEM) revealed that 310 exposed to different pressure conditions at 625 oC. (i.e., 0.1, 8 and 29 MPa) had generally the same type of the oxide structure, i.e., a Cr-rich oxide with the spinel structure on outer surface adjacent to the water phase. The material exposed at 8 and 29 MPa had a double layer oxide structure, with the outer oxide layer having a much larger grain size, while the samples exposed at 0.1 MPa showed only a single spinel-phase oxide layer. Cr-depleted recrystallized austenite grains were found underneath the spinel phase oxide. The adjacent large-grained austenite substrate had M23C6 carbides in the grain interior. The implications of these results are discussed.

Jan 1, 2015

By N. Y. Ma

Solid wastes produced in ironmaking and steelmaking off-gas cleaning systems often contain zinc. The zinc level in these solid wastes is generally too high to recycle the wastes for iron through blast furnaces, but too low to economically treat the wastes for zinc through zincrecovery facilities. The behavior, status, and distribution of zinc in the ironmaking and steelmaking off-gas cleaning systems have been analyzed from three aspects: thermodynamics of zinc condensation, oxidation and deposition, correlation of zinc concentration with particle size and density, and aerodynamics of dust particles in the off-gas cleaning systems. Theory and supporting data show that spontaneous separation of zinc from iron-bearing dust occurs in the ironmaking and steelmaking off-gas cleaning systems. Dry off-gas cleaning systems provide the most favorable conditions and environments for zinc to separate from the dust. If highefficiency dry separators were applied and appropriately arranged in the off-gas cleaning systems, zinc would be concentrated, and the majority of the solid wastes could be recycled for iron recovery through blast furnaces.

Jan 1, 2008

By Junzo Hino

Most of the waste that contains a small portion of copper is landfilled. The recycling process of copper from the waste, such as shredder residue, should be developed in order to save mineral resources and prevent environmental pollution. Shredder residue, generated from disposed automobiles and electric appliances, consists of many types of plastics, glasses and metals. The combustion heat of plastics is efficiently used for smelting in the recycling process that consists of melting and reduction. Because the waste contains numerous components the knowledge of the distribution behaviors of the main components is necessary to develop the recycling process. The distribution behaviors in the recycling process are evaluated by using the thermodynamic calculation program, HSC Chemistry. The calculation results are compared with the practical operation data of the recycling process and discussed.

Jan 1, 2003