Search Documents

By Robert A. Stansbury

The No. 14 Mine of United States Steel Corp- oration is located at Munson, West Virginia, in &Dowell County. The mine was originally assigned 7,530 acres of Pocahontas 3, 4 and 5 Seams. Production began in 1948 with a listed reserve of 64,500,000 in place tons. It was originally intended to superimpose the 4 Seam workings with the 3 Seam and mine the two simultaneously to minimize the effects of one seam on the other. Roof control problems and economic conditions led to the discontinuance of 4 Seam workings in 1958 and again in 1980, after reopening in 1972. With room and pillar mining continuing in the 3 Seam, the majority of the 4 Seam reserves have been undermined. The mine began operation using track mounted conventional equipment. Off-track conventional equipment was next used, and in 1957 continuous miners were introduced. Since this tie, continuous miners on room and pillar work have been exclusively used with the exception of a brief shortwall trial in the 4 Seam in 1975. By mid 1982, 3 Seam mining will have been completed, leaving an estimated 42 million in place tons of 4 and 5 Seam coal as the focus of mining efforts. Plans for the subsequent reopening of the 4 and 5 Seam workings have been scheduled for June of 1981. With the resumption of mining, management is faced with solving the roof support problems caused by both the inherent physical conditions and undermining.

Jan 1, 1981

By Keith Heasley

In this paper, a state-of-the-art, three-dimensional, full waveform, microseismic system was used to analyze the rock failure around a deep (> 750 in (2500 ft) of cover) bump-prone longwall panel. The microseismic system consisted of both underground and surface geophones coupled through radio telemetry and a fiber-optic network to produce pseudo real-time detection and location of seismic events surrounding the coal seam. This was the first microseismic installation of this scope at a U.S. coal mine, and the system was intended to help determine the exact strata mechanics associated with the redistribution of stress and the associated gob formation at one of the U.S.'s deepest longwall mines. Overall, 5,000 calibrated seismic events were recorded during the mining of one panel, including a Richter magnitude 4.2 event which occurred inside of the array. Analysts of these events provides a number of notable insights into the rock mass behavior. For instance, the longwall panel was widened during the retreat process, and the mining-induced seismicity shows a distinctly different behavior between the start of the panel, the mining of the narrow part of the panel and the mining of the wider part of the panel. Also, in itself, the acquisition of the ML 4.2 event was a major milestone in geomechanical and bump research. This is the first time that such an event has been recorded with this detail and accuracy at a bump-prone coal mine in the U.S. `The analysis of this single event has set distinct new limits on the relationship between mining seismicity and coal bumps.

Jan 1, 2001

By Martin Bolesta

The use of strata injection as a means of stabilizing brittle and heavily stressed ground as well as faulted zones is now state-of-the art technology. Users are obliged to select the right combination from a wide range of injection products and equipment in order to ensure that the operation will be a success. Laboratory tests and a fundamental understanding of the technical aspects of injection products not only help in drawing up the correct injection procedure but have in fact become indispensable for planning the most reliable and cost-effective solution.

Jan 1, 2001

By Paul A. Lu

This paper proposes an unconventional, simple, and practical method of measuring mining-induced around stresses with hydraulic borehole pressure cells. The method is a direct ground stress measuring technique. It does not require the value of deformation modulus for back-calculation of stresses; instead, it directly measures the ground stress in situ. The applicability and practicality of the technique are shown by two case studies. The technique may be applied to monitoring a stress build-up that may lead to mine roof failure or to rock and coal outbursts.

Jan 1, 1984

By Clare Offner

In 1998, the Australian Coal Association Research Program (ACARP) awarded funding to the School of Mining Engineering at the University of New South Wales to establish a rockbolt testing facility to research anchorage mechanisms associated with fully encapsulated rock bolts and to develop standardised testing procedures for rockbolts. This facility is still under development but has already been used to evaluate the effect of bolt profile and confinement on the load transfer characteristics of a resin encapsulated rock bolt. This paper describes the test facility and presents some of the results of development testing to date.

Jan 1, 2000

By A. Bortolussi

The paper discusses the state of the progress reached in the development of the diamond wire tool for cutting hard rocks. To the advances of this relatively new technology a substantial contribution has been provided by the research being carried out at the University of Cagliari on samples of granite rocks from different Sardinian stone quarries. On the basis of field experiments and laboratory test data, the mechanism of diamond wire cutting has been assessed. In particular the influence of the rock features and operational variables an tool performance (cutting rate and bead wear) has been elucidated.

Jan 1, 1992

By Linda K. Killoran

The U.S. Bureau of Mines has developed a prototype cross well acoustic logging system and complementary tomographic image reconstruction software for the detection and delineation of abandoned underground mines and associated subsidence failure in relatively shallow environments. The logging system uses a piezoelectric, cylindrical bender as an acoustic source. A triaxial accelerometer assembly, designed to be rigidly locked in the borehole, is the receiver portion of the logging system. Both the source and receiver probes operate at high frequencies, thus providing short wavelengths capable of resolving small features in most rock types. A modified van with a dual-drum wireline winch, 4-channel data acquisition system, power amplifiers, and waveform generator supports field operation of the logging system. A field study was conducted at a test site in San Antonio, Texas, to demonstrate the cross well acoustic logging system. The underlying rock at the test site is similar to stratified sediments in coal measures. First¬arrival travel times were interpreted by tomographic reconstruction of the velocity field in the two-dimensional cross section between the source and receiver boreholes. The resulting image correlates well with geological borehole logging data for the test site.

Jan 1, 1992

By N. C. Saxena

Subsidence investigations in Indian coalfields have led to development of relationships between subsidence movement parameters and defining of safe limits of subsidence movements for surface properties. The maximum subsidence over caved workings was generally not more than 60% of extraction thickness underground while in case of hydraulically sand stowed workings it was generally not more than 5%. The relationships have been useful in extraction of more than 7-million tonne of coal from underneath and in the vicinity of surface properties.

Jan 1, 1988

By K. Itakura

Information about geostructure for effective rock bolting must be obtained before setting the bolt into rock in a coal mine roadway. Especially, rock type variation and distribution of discontinuities such as layer boundaries, and separation of strata and cracks all represent indispensable knowledge. To achieve in-situ evaluation of roof rock, we developed an MWD (measurement while drilling) system using mechanical data from a drilling machine for rockbolt. System hardware detects torque, thrust, revolution, and stroke of the machine, and software analyzes the mechanical data log and displays locations of discontinuities using Neural Network techniques. Also, this system is able to estimate roof rock 3-D geostructure for varied rock types and discontinuity distribution in cases of a drill hole array arrangement in roof rock. We conducted a feasibility study for it using hydraulic drilling at roadways of the Taiheiyo Coal Mine, Japan. Simultaneously, some core drillings were also performed to confirm system analysis data. For core samples, distribution of cracks was observed and the borehole wall was investigated by OFS (optical fiber scope). Must discontinuity locations estimated from roof logging were conformed with data obtained from core inspection. However, the core sample contained a number of cracks which were not found in the mechanical data log. This indicates that additional cracks were generated during and/or after core drilling by the influence of rotational force of the machine and water supply. Furthermore, in comparison with the OFS image, resolution of the discontinuity's log estimated by this system was clarified; that is, it is difficult to detect small size cracks (hairline cracks) from a mechanical data log and the core inspection by OFS. This paper outlines the new hardware system for hydraulic drilling machine and compares the discontinuity map obtained from the software system with drilling core inspection.

Jan 1, 2001

By Dennis Dolinar

In general, the direction of the maximum horizontal stress in the eastern United States is fairly well defined. However, the variation of the magnitudes of the horizontal stresses is not very well understood. Because the horizontal stresses cause severe ground control problems in underground coal and limestone mines throughout the eastern United States a more complete understanding of how the magnitudes vary would be useful for developing mine design strategies to combat horizontal stress related ground control problems. Therefore, in this National Institute for Occupational Safety and Health (NIOSH) study, the variation of the magnitude of the horizon stresses in sedimentary deposits in the eastern and Midwestern United States are examined with respect to two factors, the elastic modulus of the rock and the site depth. Stress measurements from thirty-seven sites are used in the evaluation. Examining the applied excess strains indicates that the eastern United States can be, separated into high and low strain zones. For most of the eastern United States the maximum applied excess or tectonic strain ranges from only 300 to 550 micro strains. However, there is one area, a portion of the Beckley seam in the central Appalachian region where the strains are significantly higher than the other regions. In this higher strain zone, the maximum applied tectonic strains range from 700 to 1,000 micro strains. Regression models for each zone based on the elastic modulus can explain between 83 to 85% of the variation of the maximum horizontal stress. Because one region, the northern Appalachian district, has strains that are about 20% higher than the other regions in the low strain zone, multiple strain models based on geographic regions were developed for the low strain zone that can explain 87 to 91% of the maximum horizontal stress variation with the elastic modulus. Depth was found not to be a significant causal factor in any increase in the horizontal stress even though the site depths ranged from 275 to 2,500 ft. Beyond a theoretical increase, based on Poisson's effect and gravity, no other increase in the horizontal stress with depth can be justified with this data. The most significant factor controlling the variation of the maximum horizontal stress is the elastic modulus of the rock, not the overburden depth.

Jan 1, 2003

By Anthony Iannacchione

As the amount of new fractured surfaces or "damaged rock layers" within roof rock increases, the stability of the rock mass decreases. While direct measurements of this phenomenon are not easily made, there is good circumstantial evidence to support this hypothesis. For example, it is common to observe increased cracks or fractures in the immediate mine roof rock before a roof fall. Likewise, roof drill holes placed in areas that later fail often reveal increased numbers and/or separations of fractures within the rock column through time. And finally, the frequency of microseismic activity, representative of rock fracturing, increases before a roof fall. For this study, more than 700 microseismic emissions were collected from two underground limestone mine roof fall areas in southwestern Pennsylvania. Microseismic events were located and magnitudes determined using the moment magnitude technique. Moment magnitude is based on the event seismic moment, which is a measure of the seismic deformation. The amount of new fracture surface length was calculated based on the stored strain energy within the rock prior to fracture. In the two case studies presented, a significant amount of microseismic activity was observed as much as two days before the first signs of failure in the roof fall areas. Additionally, results from this analysis reveal much about the behavior of strata prone to failure and allows for the construction of hazard maps based on microseismic emissions. The potential use of this technique as a means of anticipating roof falls is analyzed and discussed.

Jan 1, 2004

By P. E. Christensen

Due to ever-increasing stripping ratios associated with the No. 8 Seam at the San Juan Mine surface operation, BHP Minerals decided to implement longwall mining for the extraction of the substantial future reserve base. In preparation for longwall developments, BHP opted to first develop a small-scale pilot operation within the No.8 Seam on an adjacent lease to address geotechnical/geological concerns related to ground control, subsidence, caving, panel and entry design, and operational issues related to entry development and proper face equipment selection. Room-and-pillar mining methods are currently being utilized to develop a full extraction panel for a wide range of geological, geotechnical, and geomechanical evaluations aimed at characterizing and assessing the mineability of the No.8 Seam. Variable roof and floor conditions, coupled with a multi-bench coal seam, require that a number of mining horizons, opening geometries, and roof and rib support fixtures be evaluated relative to expediting gate and panel developments. Issues related to development of timely caves in areas subject to overlying sand channel deposits will also be addressed through underground in-seam stress and deformation measurements, and interburden and surface subsidence monitoring. This information will ultimately be used to evaluate face support and gate and panel pillar/entry development requirements. The current depositional model for the property, developed from an aggressive drilling, highwall mapping, and lineament evaluation program, will also be refined during the Pilot Mine study through extensive in-trine mapping, additional roof and floor drilling and physical property testing, and determination of the in situ principal horizontal stress field.

Jan 1, 1998

By Yi You

A research has been conducted to study the long-term subsidence and its possible effects on surface structures In this research, the surface movements in areas when potential for developing long-term subsidence is high have been monitored over an extended period of time Long-term subsidence data have also been collected from other sources The avail- able data from this on-going research have been analyzed and the results is presented in this paper.

Jan 1, 1997

By Wei Wu

A new bench blast design method and its realization with the assistance of the computer is introduced. The basic design principle is to define a rhomb cell, called fully-fractured zone, through a series of full scale bench crater tests and apply this geometric pattern in multi-hole, multi-row blast design. To illustrate the design method, the optimization process and assessment of blast performance are presented in the context of a case study.

Jan 1, 1992

By James J. Scott

Over the past two years research, development ad field tests have been conducted on a new product called the "Scott Cable Sling". This work resulted in the awarding of U.S. Patent No. 4265571 on May 5, 1981, to the inventor. Work on this' project was done by the staff of Scott Mine Technical Services, Inc., and is in keeping with its philosophy of advancing mine grad control technology. Recent acceptance by industry has resulted in volume purchases of the product and indications are that it will gain wide acceptance by the mining industry. The system features flexibility in its application and is useful in both roof and rib control. This paper describes the product, discusses its range of applications and cites specific field examples of its use.

Jan 1, 1981

By Francis Kendorski

A longwall coal mine in Appalachia about 1,500 ft deep encountered a fault while developing a new longwall panel. The fault extended from mining depth to the surface near a secondary road and drainage. The fault was located inside the anticipated angle of draw within the mined panel and gob. The fault extended vertically out and up, away from the panel, caved zone, and gob at nearly the angle of draw: the fault very nearly following the angle of draw. It was initially thought that "fault reactivation" could possibly occur. Fault reactivation is the phenomenon of having mining subsidence localized along a fault leading to a "reactivation" of the fault and shearing and displacement along the fault. Such fault reactivation would disrupt and deform the fault plane beyond the normal angle of influence of the subsidence trough, and may provide a conduit for any ground and surface waters to reach the mine. We contacted all operators of longwall mines in Appalachia to determine if any Appalachian longwall mines had ever experienced fault reactivation, and teamed that none had experienced the phenomenon. After studies of possible water intrusion quantities and rates based upon in-fault pump tests, which indicated that water intrusion rates should be manageable, and the prior experience that faults in this particular area were usually barriers to water flow, mining proceeded with caution and monitoring. Mining was successful with no noticeable increase in water inflow rates, and no measurable off-setting of the fault exposure on the surface. It can be concluded that the fault did not reactivate due to its relationship to the mining sequence.

Jan 1, 2003

By B. (Mamas) Das

A project to evaluate the suitability of point Load strength tests for testing and classifying coal measure rocks for coal mining application was initiated by Canada Centre for Mineral and Energy Technology (CANMET). A summary of this study with emphasis on the important findings is presented in this paper. The instrument as used in this study is a Robertson Research Rock Strength Index Log. Because of the variation in the correlation ratio between uniaxial compressive strength and point Load strength index for hard rocks and soft rocks it was decided to establish this corre¬lation initially on cement concrete specimens specially prepared for this purpose following ASTM specifications. These specimens are expected to represent soft rocks and at the same time would be of uniform quality. Once a general trend of this correlation was established tests were performed on coal and rock samples from the sub-bituminous and bituminous coalfields in Canada. The most important results may be stated as follows: (i) Generally, the common value of the ratio between the uniaxial compressive strength and the point load strength index ranges between 8 to L4. (ii) The Robertson Research Rock Strength Index Log proves to be quite suitable for testing sandstone, siltstone and some coals from the bituminous coalfields but problems have been experienced when testing weathered samples or samples from the sub-bituminous coalfields. (iii) In some cases tests were successful if Larger samples from weathered zones or from sub-bituminous coalfields were used. However, a magnified load gauge for 0-3KN or 0-5KN is expected to be the best solution for soft and weathered rocks in most of the cases. Some mudstones and some rocks from weathered zone do not appear to be suitable for these tests. This aspect of the study is still under investigation. (iv) Deterioration of rock properties due to weathering has been determined through tests on samples collected from weathered and unweathered samples.

Jan 1, 1984

By Kevin Beauchamp

In many cases traditional support designs cover the many variations in ground conditions and bolt performance by a conservative factor of safety. The result is that most bolts are ineffectual most of the time and yet the response to occasional roof collapses is an even more conservative design. The probabilistic analysis presented in this paper takes several important parameters of a support design into account such as span, bolt strength, bolt length, water pressure, seismic accelerations, joint orientation, bed thickness and joint strength and allows the effect of variations in these parameters to be evaluated simultaneously. The analysis demonstrates the application of the probabilistic approach to both blocky, wedge-dominated conditions and bedded deposits dominated by laminations. All mine excavations have a designed stand-up time. By taking into account of the possible variations in the design parameters explicitly, it is possible to produce a support system designed to ensure stability over a given period of time. Rather than use a factor of safety criterion, the approach uses a percentage reliability or probability of failure. By understanding the probability of failure of the support system, it is possible to improve the performance of ground support without any increase in cost or conversely to decrease the cost while maintaining the performance of ground support. This approach reduces reliance on empirical experience and leads to a better understanding of the key factors that influence stability and can provide a much more accurate and optimized assessment of support design and performance. The result is a more cost-effective support system and we hope that a broader application of this approach to ground support in underground mines will lead to a greater acceptance in the industry of probabilistic analyses and of terms such as Probability of Failure and Reliability of Support.

Jan 1, 2003

By Bob Thomas

The roof drill operator productivity can be enhanced by the introduction of control technology The operators control station can be improved by considering human factors such as handle forces and control location. The smaller electrical controls can be located much easier than the traditional hands on valves. The operators control can he improved by using processors with programmable subroutines that assist the operator in the decision making process. For example to increase feed rate - to slow rotation - to avoid clogged steels - etc. The overall affect is to improve drilling and bolting consistency. The control system uses a dedicated processor packaged as an intrinsically safe control station. The roof drill operator is assisted in the drilling; arid bolting by a closed loop feedback system. The processor monitors the drilling parameters such as feed force, feed rate, rotation torque, RPM, drill position, and vacuum condition Based on the drilling parameters the processor executes pre-determined condition statements intended to enhance drilling The drill operator has an active display to alert him to the real time machine status. For example if the feed were to slow or delay due to a high vacuum level the display would show "high vacuum". The dedicated processor is available on the arm feed style machines, The prototype machines used programmable logic controllers to develop the feedback relations. The ability to record drilling parameters was extremely helpful in this development project. The extended use of the recording feature will aid operators in mapping the mine roofs Interpreting the recorded drilling parameters can reveal a void in the top or hard competent drilling The prototype machines also showed the importance of vacuum monitoring This feature is extremely valuable in softer materials, The benefits of the control system range from efficient use of the consumable bolting materials to uniform operator performance.

Jan 1, 1999

By J. A. Nemcik

Although floor failure at longwall faces has been traditionally associated with a soft floor, in many csses floor buckling has been observed just ahead of the longwall supports, despite the floor being a competent rock The floor failure is associated with the presence of weak bedding planes in the floor and the movement of strata towards the goaf opening. This paper presents the principles of the floor failure based on numerical modelling and field observations and outlines the practical approach to estimate the risks involved with floor failure.

Jan 1, 1995