Search Documents

By David H. Tang

Similar massive pillar failures were observed in two underground coal mines with different configurations of mine workings and overburden depths. Finite element models were used to analyze the causes and mechanisms of the pillar failure. The results of the analyses confirms the underground observation. For Case No. 1 the failure of coal pillar is mainly caused by a combined effect of smaller coal pillars under a large overburden and the interaction of multiple seam mining. For Case No. 2, the pillar failure was initiated by the weak roof rock but the ultimate pillar failure was caused by the splitting of pillars into very small size.

Jan 1, 1984

By Deren Zhu

Based on the results of field observation and physical model analyses, a computer simulation method, FEAEBP, has been developed for simulating the breakage of the main roof by considering it as a Kirchhoff plate on Winkler elastic foundation. By this method various parameters of rock property, different boundary conditions of the working face and the initiation, development and results of the breaking process of the main roof with different geometric dimensions can be effectively simulated. Since the main and immediate roofs, and the coal seams are treated as an integrated mechanical system, the interaction among them can be studied in detail.

Jan 1, 1988

By Laxminarayan Holla

There exist many formulae for designing coal pillars. However, when applied to a given set of mining parameters, they lead to different pillar sizes and factors of safety. From the subsidence point of view, the pillars designed as protection pillars not only have to be stable, but also have to limit subsidence over them to a level acceptable to the structure being protected. The subsidence over a pillar of given width to height ratio depends upon the mining depth. A pillar may be stable, but the subsidence over it may be quite large and unacceptable for the structure. In many cases even though pillars may yield, they support the undermined strata and reduce surface subsidence. In addition, the yielding pillars eliminate peaks and troughs in the surface subsidence profile and reduce ground strains. In a given situation, whether a pillar yields or not depends primarily upon its width in relation to mining depth.

Jan 1, 1992

By W. G. Pariseau

A new approach to the direct inclusion of the effects of joints and geologic structure in rock mechanics analyses is applied to an elastic analysis of stability of a Lucky Friday undercut and 4111 longwall stope (WL) using the finite element method (FW). The approach is base+ on the concept of equivalent properties of a heterogeneous test volume, but does not depend on the assumption that a test volume is a representative volume element. Comparison with conventional FW results show greater variability in fields of stress, strain, displacement, safety factor and energy densities. Stability requires a knowledge of rock mass strengths as well as elastic moduli.

Jan 1, 1989

Case study data were analyzed to develop and quantify empirical stress transfer relationships between seams for both longwall and room and pillar mines. Layering in the innerburden and the distance between seams were determined to be the controlling factors. To evaluate the effect of bedding planes on stress transfer, laboratory studies were conducted using layered, low modulus gravity loaded photoelastic models. Parameters investigated were thickness, number of discrete layers, modulus and friction between layers. Results showed that there was significant distortion of the pressure bulb in highly laminated conditions which correlated with the results of empirical analysis. Relationships developed were used to modify the results obtained from numerical modelling between multi-seam longwall operations. Research conclusions were demonstrated using case studies.

Jan 1, 1995

By D. M. Shu

A two-dimensional finite element modelling technique is applied to predict the subsidence movements on a sloping ground surface above a completely mined panel. The modelling is carried out for the surface both directly and using a combination of an equivalent horizontal surface and a rays projection method and the result compared. The rays projection method provides the subsidence components on a sloping surface from the corresponding ones on an assumed equivalent horizontal surface through the point of mean elevation of the relevant part of the sloping surface. This method is used next to compare the subsidences, horizontal displacements and horizontal strains from the mining of a given panel at the surface for different inclinations. The results show that the magnitudes of the subsidence components are greater on the dip side of the slope from the point of the mean elevation, than the corresponding ones on the rise side and the asymmetry increases with the inclination of the surface. The findings are also compared with those of other research workers.

Jan 1, 1992

By Revendra Awasthi

The application of a horizontal inclinometer and a tiltmeter to measure tilt, curvature, and deformations of shallow footings during mine subsidence is described. The measurements were taken during mining of a longwall panel in Southern Illinois and were supplemented with precision level survey data. Monitoring was conducted under a cooperative agreement between the Institute for Geotechnology at The University of Tennessee, Knoxville, the U.S. Bureau of Mines, the National Science Foundation, the Illinois Mine Subsidence Insurance Fund, and Old Ben Coal Company. Six different footings were constructed and instrumented at two sites; one above the panel centerline, and the second inside the edge of the panel in the anticipated zone of maximum tension. A brief description of the inclinometer casing and tiltplate installation is described, and the results obtained from the two instruments on a plain concrete footing compared. Observations of footing deformations and curvatures calculated from the inclinometer and tiltmeter data are also presented, and the results compared with observed structural damage.

Jan 1, 1990

By George J. Karabin

Since the inception of a qualitative pressure arch theory by Haak4 in 1911, much work has been done in an effort to apply this concept to underground mining. It has been used in both longwall and room and pillar mining to determine roadway and pillar stability (with varying degrees of success). This paper presents a summary of a case study where the pressure arch concept was extended in a totally qualitative manner to define the source of roof control problems in the mains of a Pennsylvania mine. It was concluded that, due to the method of mining employed, a pressure arch formed over a portion of the entries, and the high abutment stresses accompanying it resulted in extreme roof deterioration. The following discussion will include a general presentation of the arching mechanism, the physical response of the roof strata under mining-induced abutment stresses (both from the case study and in general), a computer simulation of ground stability under both "normal" and "abutment" stress conditions, and finally, potential means of alleviating such conditions.

Jan 1, 1982

3-D finite element modeling was performed to study the effect of bedding plane sliding and separation and tensioned bolt in layered root It was found that the major influence zones of a tensioned bolt are restricted to the neighborhood of the anchor points; that bedding plane sliding and separation releases the vertical stress in the roof above entry but greatly increases the horizontal stress within the first layer of the roof, and that there is a triangular zone between the two adjacent bolts at and near the roofline level that is beyond the influence zone of the bolts which is liable to fail if conditions exist. Based on the results, three possible modes of roof failure are proposed for the design of tensioned bolting.

Jan 1, 2001

By Keith A. Heasley

Pillar recovery in deep coal mines with competent roof and floor can concentrate stresses and generate hazardous bumps. Actual calculation of the geologic strain energy released in association with these coal bumps has been rare, although energy release values have been utilized successfully for indicating burst potential in numerous hard- rock mines. This paper advances the current knowledge of energy release calculations as applied to coal bumps through an extensive analysis of an actual bump occurrence. The U.S.B.M, displacement- discontinuity code, MULSIM/NL, is used to produce a numerical model which generates stress, displacements and energy values associated with a pillar retreat section. This model is calibrated with actual field data, and then dissipated energy values from the model are examined as to their suit- ability for indicating bump potential. Ultimately, it is determined that prudent application of dissipated energy calculations can be used as a tool to investigate the coal bump potential of a mining plan or cut sequence.

Jan 1, 1990

By Liang Yin-Huai

In Fuxin Coal Mines, there are more than 20 million tons of coal buried under seasonal streams. The coal seams are mostly shallow. We have mined more then 50 mining blocks distributed in 5 coal mines. Their natural conditions are different, and the consequences are also more or less different. However, no stream-water-inrush accidents under regular mining conditions are the same. There were 3 exceptions. They were caused by unexpected roof caving which made valleys or alluvia subside as funnel-like cavities and let in inrush of stream flow. The key to our success in mining shallow under-stream coal seams, according to our analysis, is that valleys or alluvia subside gently and basically evenly with contractible tension fissures and that fissures both in valleys or alluvia and in rock seams are blocked up or sealed by cohesive deposits either from alluvia or rock. This paper treats: (1) some typical illustrations of mining shallow coal seams of different occurrences under streams of different sizes, flowing capacities and valley structures, (2) observations of the height of caved and fissured zones and subsidence of valleys or alluvia, (3) observations of underground water flow before, during, and after mining and the fluctuation with respect to stream flow, (4) observations and analyses of blocking up of fissures caused by mining, and (5) feasibility of mining shallow under-river coal seams.

Jan 1, 1990

By Lewis A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control systems to monitor rock mass loads at Tg Soda Ash's trona mine, Granger, WY. Axial and shear loads were determined to levels of strain gauge accuracy of ±5 N or ±5 microstrain. These gauges were embedded in a remanufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. These data provide necessary input for an operator to design a safer working environment for miners.

Jan 1, 2001

By M. Bouteldja

A finite element modelling approach is developed for the evaluation of the mechanical performance of cable bolts supports in underground mine structures. The modelling approach permits the simulation of any arbitrary number or pattern of cable bolts, that can be either partially or fully grouted, with or without end plates. The modelling technique used treats each cable bolt as a set of bar elements representing the steel cable. The bond stiffness characteristics of the grout bolt interface are represented by shear springs uniformly distributed along the cable length. Coupled with a simple linear elastic analysis, this technique can serve as a dedicated numerical model for cable bolted excavations. The application of the model is illustrated with two case studies: one for a hard rock mine and another for a coal mine.

Jan 1, 1999

By John C. Stankus

From research started six years ago, a new design criteria has been developed for mine roof bolt systems This design criteria precisely and quantitatively determines parameters such as bolt length, installed tension, and spacing that will produce the Optimum Beaming Effect (OBE) OBE, a new roof control term, is defined as the roof beam that has no separation above and within the bolted range with the shortest bolt passible Utilization of this design criteria has shown that in many cases shorter roof bolts with higher installed tension can produce a much stronger beaming effect (Stankus, 1995) This paper will first present a brief deception of how the design criteria was formulated From there, actual case studies where the design criteria was utilized will be discussed In conclusion, current and future research efforts will be presented

Jan 1, 1997

By Rao Pothini

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support. This paper describes in detail the testing methods, data analysis results obtained, and recommended changes.

Jan 1, 1992

By Thomas E. Marshall

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) examined and characterized conditions at a majority of the underground stone mines in the United States. Observations at these mines revealed a limited degree of roof monitoring beyond visual inspection and sounding. When monitors are used, they typically require the miner to measure movement at the roof. If conditions are unstable, the miner may be in a hazardous situation while recording data. Based on this scenario, researchers surmised that a simple, inexpensive monitor with the capability of recording data at a distance from the mine roof would be a safer way to gain the information. Additionally, more widespread use of monitors could potentially lead to better understanding of roof movement in general. A monitor to meet this need was designed, tested, and subsequently improved as experience was gained in its' use at a number of underground stone mines. The Roof Monitoring Safety System (RMSS) can provide an initial indication of movement in roof beams. By understanding and measuring roof movement in underground mines, the potential for injuries and fatalities to mine workers From falls of ground can be reduced. Also, officials at a mine with a history of data are better prepared to make a decision on remedial actions in the event of ground falls. This paper will outline the evolution of the RMSS and how it can be used in a comprehensive pro-active ground control safety program. Also included is a cast history describing how the RMSS was used in an evaluation of the effectiveness of a mechanical impact scaling machine at an operating limestone mine.

Jan 1, 2000

By Anthony T. Iannacchione

Longwall mining produces surface subsidence basins that affect streams by water diminution and contamination. These effects can ultimately impair the biological character of the plants and animal communities living in the streams. The combination of flow, water quality, and ecological effects threaten the environmental sustainability of longwall mining and, ultimately its social acceptability. Pennsylvania has developed new standards, released in 2005 and implemented in 2007, to help protect the commonwealth?s valuable streams from the detrimental effects of subsidence. These standards are aimed at eliminating environmental problems and will therefore help to make underground bituminous coal mining more sustainable. The engineering solutions necessary to comply with these standards are fundamentally affected by the geologic nature of coal-bearing strata, the existing in-situ stress conditions, and the ability of selected species to survive and adapt to changes in their environment caused by longwall coal mining subsidence. Needless to say, geologists, biologists, and engineers are all playing a pivotal role in developing prevention controls and recovery measures necessary to protect streams and sustain underground coal mining. The challenges facing scientists and engineers in sustaining the development of underground coal mining in Pennsylvania are examined through case studies. These challenges all arise from the subsidence effects of longwall mining. The key effects of subsidence, discussed through case studies, are: a) tension cracks, b) springs in headwater stream areas, c) stream gradients and subsidence basins, and d) stream compression ruptures and horizontal stress. All of these potential threats demonstrate the need for high-level scientific knowledge and innovative engineering solutions. One could argue that Pennsylvania?s stringent stream protection standards put the coal mining industry at a competitive disadvantage compared to other coal producing states. It is equally likely that compliance with these standards help to mitigate the effect of subsidence, thereby helping the coal industry achieve a sustainable future.

Jan 1, 2011

By Keith Heasley

An eastern longwall mine was required to mine through a set of three entries located midway down the length of a panel. Of course, the mine desired to design a successful support system for the mine-through area at the least cost. To further complicate the design process, the mine-through entries were located directly under the end of a previously mined, overlying longwall panel and the entries were close enough to be subject to stress interactions from the overlying seam. In order to accurately evaluate the multiple-seam stresses and modify the mine-through support system appropriately, the boundary element program LaModel was used to model the stress and displacements in the two mines. Using the results of the model's stress analysis, the support density was systematically varied throughout the mine- through entries for optimum sup@ efficiency and economics. During the actual mining of the cross panel entries, the longwall experienced few, if any, additional delays, and overall, the support and mine through of the cross-panel en- tries at Harris #1 was very successful, saving the mine confineable time and money.

Jan 1, 2003

By James G. Schotsch

Unmapped abandoned mines are hazards for under¬ground mines, surface mines and surface structures. The Radio Imaging Method (RIM) provides a cross borehole technique to remotely detect abandoned mine works. RIM was used at the Buck Creek Mine, an underground coal mine, to determine the extent of unmapped mine works. The information provided by the RIM survey assisted the mine planners in developing their mine.

Jan 1, 1990

By Eric Zahl

Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, Spokane, WA, have collaborated with three Western longwall coal mines in an ongoing effort to develop technologies that will aid in providing safe and stable working areas. The goal of the research described here is to develop a stress monitoring system that will provide immediate information to mine managers for making daily safety decisions as areas of poor ground are mined through. Initial work has focused on answering preliminary questions regarding the reliability and use of stress change patterns. Research is concentrated on monitoring horizontal stress because horizontal stress is transmitted over long distances through stiff strata, thus allowing an extended length of entry to be monitored. This paper presents an explanation of the concept, key results from field tests at two mine sites, and a proposed process for imple¬menting a monitoring system. System design layouts, instrument use, data collection and interpretation methods, and processes to present findings to mine staff are described. Additional validation and correlation with actual failure mechanisms are required before this approach can be recommended at ongoing operations. How¬ever, initial results indicate that this approach shows promise in mines prone to bumps and roof falls associated with large stress changes. In particular, analyses of measured changes in horizontal stresses appear useful.

Jan 1, 2002