Search Documents

By R. J. Sweigard, G. T. Lineberry, B. K. Slone, F. A. James III, D. S. Maggard

The depth at which it becomes more economical to use slope access instead of box-cut access for nearsurface coal reserves is termed the "transition depth." The transition depth can be established for a given coal property by considering cost estimates for those parameters that determine respective access methods. Fourteen parameters that influence access cost were identified, and ranges for these parameters were determined. A transitiondepth formula was developed to permit the determination of which is the better method of accessing a reserve, given information such as high wall slope, road width, total bench width, pit dimensions, road grade, belt component costs, pumping costs and the cost of overburden removal and reclamation. In most cases in Appalachia, especially in eastern Kentucky, the observed transition depth ranges from 20 to 30 m (66 to l00 ft). This indicates that actual practice is consistent with the analytical approach used.

Jan 1, 2002

By K. Cothern, S. Novack, D. A. Johnson, R. Borden, S. Pavlou

A procedure is presented for ranking hazardous waste sites for remedial decisions, and an example with application to mining waste sites is discussed. Typical contaminant concentrations are calculated from field data. Exposure indices that compare these measured concentrations with allowable limits are then computed. The limits are selected to protect both the health of humans (for both carcinogen and noncarcinogen effects) and the health of key organisms in the ecological food web. The additive exposure index for a site, defined as the sum of all contaminant-specific exposure indices, is then used in ranking the sites and assigning each a priority for remedial action. One key source of uncertainty in the process is the estimation of a typical site concentration from data that include values reported as "below certified reporting limit" (BCRL). This uncertainty is compounded in the additive exposure index and therefore may have a substantial effect on the assignment of remediation priority. A general approach is presented for incorporating consideration of BCRL data into uncertainty evaluation when assigning remediation priority designators to hazardous waste sites.

Jan 1, 1992

By P Moser

Within the EU-research project "Blasting Control", jointly operated with partners from France, Italy and Greece, between 1992 and 1995, the Department of Mining Engineering of the Montanuniversity Leoben, Austria took over the task to develop a diagnosis system applicable in underground drifting, in order to identify possible reasons for blast failures or poor blast performance. For that purpose 120 m of 12 m2 test galleries were excavated at two different mine sites. For every blast performed the collar and bottom position of every hole drilled, the charged hole length and the drift and face profile of the round blasted were monitored. These 'geometrical" data were put directly from the measuring devices into SURPAC, the mine planning software chosen for data analysis. Based on the data computed, 3D plots comparing actual and planned data were made visible on the screen or as hard copies. Experience from the introduction of this system into a mining operation showed, that the system developed contributes to an improved understanding of the reasons for blast failures and forms the basis for an improved blast design. The soft- ware package SURPAC was also used to train the miners directly at the mine site in order to improve the quality of their work.

Jan 1, 1996

By D. R. Buist

The Taharoa plant of New Zealand Steel Mining Limited extracts a 57% Fe titano-magnetite concentrate from a large mineral sand deposit 90 miles south of Auckland on the west coast of New Zealand's North Island. The plant consists of an 18-inch suction cutter dredge which feeds a 750 TPH floating separation plant. An initial gravity/ size separation is obtained using cone concentrators. Finished concentrate is produced by a combination of conventional drum magnetic separators and top fed wet Mortsell magnetic separators. Concentrate is stockpiled by cyclone, and reclaimed by a bull- dozer and tunnel system. Repulped concentrate is pumped by sub- marine pipeline to slurry tankers anchored at a single buoy one mile offshore. Current concentrate production rate is in excess of one million metric tons per year.

Jan 1, 1973

By A. I. Makhin, S. M. Sablukov, V. K. Sobolev, V. A. Larchenko, V. S. Shchukin

The kimberlites of northern Europe are related with a large crustal block having a northwest-southeast orientation. Kimberlites penetrate the Archean formations of crystalline basement, Late Proterozoic rocks, which are overlapped by Middle Carboniferous and younger deposits. The kimberlites bodies include pipes, dikes and sills of Upper Devonian age. Within the region, rocks of two magmatic series form diamond-bearing kimberlites. Aluminum rocks form a new type of diamond-bearing rock that is not found in other diamond provinces. Kimberlites of this region are characterized by highly developed deuteric alterations, a low content of associate minerals, the presence of two diamond generations and an increased content of jewelry-grade diamonds.

Jan 1, 1997

By John Waggoner, Steve Klein, John Townsend, Jay Arabshahi

The Riverside Badlands Tunnel is a 13 km (8 mile) long segment of the Inland Feeder Project. This 3.65 m (12 ft) finished diameter water tunnel presented many challenges that had to be overcome to take the project from concept to reality, not the least of which were the diverse ground conditions. Construction of the tunnel was carried out by a single tunnel boring machine (TBM) in one tunnel drive. The project is considered a success due to the accurate baseline established for the ground conditions; the approaches used to mitigate adverse conditions; and the appropriate use of TBM excavation methods, which achieved rapid advance rates despite the challenging ground conditions.

Jan 1, 2003

By T. W. Oshnock

Pulverized coal (PC) and other injectants can be injected into the blowpipes of a blast furnace to decrease coke requirements. Throughout the history of blast-furnace development, there have been many attempts at injecting PC. In the 1960's a more serious effort was made to improve pulverized coal injection (PCI) technology. However, because of the additional capital requirements and the projected near-term inexpensive cost of other injectants, very few PC1 systems were installed. When the second oil crisis occurred around 1979, the shortage and high cost of fuel oil caused blast-furnace operators to operate without oil injection. It was soon discovered that blast- furnace operation without oil was not as smooth or efficient. Experiments with PC1 quickly showed that coal was a good replacement for oil which resulted in the rapid application of PC1 in both Europe and Japan. As a result, PC1 technology for blast-furnace operation has progressed rapidly during the 1980's. This paper will describe the worldwide status of PCI, characteristics of different PC1 systems, the effect of PC1 on blast-furnace process parameters, and the economic effects of using PCI. Results from the USS Blast-Furnace Thermochemical Projection Model comparing the effects of different coal properties and the effects of other tuyere injectants such as oil and natural gas will also be described.

Jan 1, 1988

By C. K. Lee

The influence of passageway fires on ventilation flows was investigated in three horizontal fire tunnel s: 1. a laboratory-scale fire tunnel network, 2. a small-scale fire-plume tunnel, and 3. a large- scale simulated mine gallery. Wood was used in the first and third tunnel and gas-burners were used in the second one to generate passageway fires. Experimental measurements included gas mass flow rate, velocity, temperature and pressure in the passageways and exhaust fans. The overall and local effects of the fires were investigated by comparing these measurements obtained before and during the fires. Results show that a passageway fire essentially increases the flow resistances of the passageways of a tunnel flow network by virtue of volatile fuel mass injection and high combustion temperatures. The ventilation air flow rate is consequently throttled to lower values than that before the fire. At severe throttling, reverse flow occurs. Conditions for reverse flow are characterized by two Froude numbers based on gas velocity and density upstream of the fire, and height of the passageway. The Froude numbers and the characteristics of the passageway fire are necessary to analyze mine ventilation/fire interaction and to predict mine ventilation patterns during fires.

Jan 1, 1980

By M. K. Gangal, E. D. Dainty

The CANMET diesel-related work, carried out in cooperation with the Canadian mining industry, resulted in the identification of several useful R/D studies. One such study was the development of a dash-mounted alarm signal system to indicate overexposure of production LHD diesel vehicle operators to toxic contaminants in a mine environment. The resulting instrument has been called the [CO2 Exposure Meter]. This meter is particularly applicable to LHD machines because previous investigations have indicated that operators of LHDs and some haulage truck drivers are exposed to up to 200% of the contaminant concentrations measured in the general mine return air. This paper describes the development of the system which continuously monitors and displays the operator's exposure to diesel pollutants, and indicates an overexposure by an alarm light. The overexposure limits are preset by mine personnel based on carbon dioxide (CO2) measurements, which in turn are related to simultaneous spot respirable combustible dust (RCD) measurements (or to Air Quality Indices - AQI, if available). The CO2 settings are, in general, related to the engine/exhaust treatment selections, vehicle duty cycle and local ventilation rates and efficiency. The system continuously displays one of three lights: green for underexposure, yellow for caution, and red for overexposure. Overexposure can occur for several reasons, such as: reduced ventilation, malfunction of the diesel vehicle, and excessive airborne contaminants. The paper confirms satisfactory operation of the system in a laboratory-simulated mine environment, as well as in field trials.

Jan 1, 1993

By B. Cavender

Mining managers trying to rapidly reduce production costs tend to implement a traditional set of topdown managerial practices: reductions in production volume, employee layoffs, renegotiation of supplier contracts, cancellation of employee training, restrictions on travel, reductions in office supplies, and so forth. While these practices do reduce costs, the benefits are often limited in both magnitude and duration, and the workforce is usually left demoralized. Successful cost-cutters take a different approach. They make the continuous reduction of costs a priority for all members of the organization, whether managers or workers. The culture of these firms emphasizes the commitment, voluntarily given, of individuals and work groups to this goal. Cost-cutting practices often reject all of the traditional methods mentioned above, but are far more numerous, innovative and successful. This culture of cost reduction is the result of a set of leadership competencies that establish direction for the organization, align the organization's various constituencies with this direction, and motivate and inspire the organization. Cost reduction then becomes a routine task rather than a heroic achievement.

Jan 1, 2002

By A. Pavlides

The purpose of this work is to conduct a preliminary analysis of the spatial variations of the thickness of lignite layers in the area of the Amyndeo mine, and to estimate the lignite reserves of the mine. The reserves are estimated by the method of the Voronoi diagrams, using a group of mirror points to close the polygons around the boundaries of the mine. Two data sets are investigated. The first one corresponds to an exhausted part of the mine. The derived reserves estimates are compared with the actual data obtained by the Public Power Corporation (PPC) to validate the analysis. The second data set extends over the entire mine, and it is used to derive an approximate estimate of the total lignite reserves. A geostatistical analysis of the total layer thickness is performed. The experimental semivariograms are evaluated for both data sets in different spatial directions. Two possible theoretical models for the experimental semivariogram (the exponential and a novel Spartan model) are compared and discussed. An interpolated kriging map of the total thickness variation is produced accompanied by a map of the kriging precision. The performance of kriging interpolation is discussed in terms of cross validation measures.

Jan 1, 2007

By Por J. B. Evans

El mantener un beneficio óptimo sobre todo el conjunto de un emplazamiento minero necesita una constante puesta al día de las estrategias operativas. En esencia, cada estrategia es una combinación particular del gasto del capital previsto, el flujo de ingresos y el tiempo transcurrido. La selección de una estrategia basada en el beneficio potencial requiere que cada estrategia contemplada con un ordenador, un análisis tal puede ser engorroso. Este capítulo discute o desarrolla una técnica de "corte rápido" que asigna una relación de beneficio a las estrategias alternativas e identifica aquellos aspectos de una estrategia que producen mayor impacto sobre el beneficio. Esta técnica puede proporcionar valoraciones rápidas de suficiente precision para muchas de las decisiones de las estrategias operativas que se toman sobre la marcha en minas que se encuentran en explotación.

Jan 1, 1982

By Osvaldo Bascur, Laurent Garrigues, Nouna Kettaneh, Svante Wold

The chemical, oil, semiconductor, mining, and paper and pulp industries, as well as most other modern industries, are rapidly expanding the range of measurements used to characterize raw materials, process steps, intermediates, and final products. In addition, process variables such as temperature, pressure, and flow become more and more numerous, providing extra information on the state of the process. However, no matter how many sensors are added, the underlying sources of variations that drive the process behavior remain constant. On the other hand, the measuring frequency of these data has increased from once a day or once an hour to once, ten, or even hundred times a minute. This gives masses of data that are swelling in both directions (more variables and more observations). These data need to be properly stored, managed, and analyzed to provide diagnostics about the state of the process as well as an understanding of the relationships between different parts of the process and the product properties. Projection methods such as PCA (principal components analysis) and PLS (projection to latent structures) compress process data to informative summaries of the original variables. These can be shown on line, providing an efficient, graphically oriented suite of diagnostics regarding the "health" and performance of the process. The power of these methods is illustrated by two examples of industrial data in the mining industry.

Jan 1, 2000

By Joseph M. Denk, Gary J. Wirth

This paper summarizes a three phase face ventilation study which was conducted from September 1989 through March 1990 to determine face area methane liberation patterns on two extended longwall sections. The coal seam being mined was considered gassy and the mine liberated an average of 14.4 million cubic feet per day (cfd) or 0.41 million cubic meters per day (cmd) of methane through the mine fans. The mine also used an extensive underground degasification program to recover up to 13.4 million cfd (0.38 million cmd) of methane. Data was collected while the longwall sections were mining from the beginning, middle and end of panel extraction to determine the relationship between the methane liberation and extent of longwall retreat. As expected, methane concentrations did increase from the headgate (intake) to the tailgate (return) side of the longwall face and peak concentrations were detected above the shearer as it passed a methanometer location during mining. There were significant differences in the methane liberations due to the location of the active face within the longwall panel. Results from this study could be used to determine a minimum design face air quantity for an extended longwall section operating under similar conditions.

Jan 1, 1991

By Cathleen J. Webb, Arden D. Davis

Begun in 1992, an abandoned and inactive mine inventory in the Black Hills National Forest has resulted in a hazard ranking of the most severely affected sites. For purposes of the inventory, the Black Hills were divided into three main regions: the northern Black Hills, with primarily gold mines; the central Black Hills, with pegmatite mines and some gold mines; and the southern Black Hills, with primarily uranium mines. A computerized data base has been developed along with standard forms for field crews. The forms were designed to provide maximum compatibility with other abandoned mine inventories on various federal and state lands. Measures recommended for the most hazardous and heavily affected sites include regrading of unstable slopes, fencing of open shafts, and remediation of the most severe acidic mine drainage problems. Specific examples are illustrated where remediation and safety measures were recommended or have been implemented. The vast majority of the sites, however, needed little or no remedial action.

Jan 1, 1995

By John F. Spisak

Versatile living organisms, historically exploited as functionaries in the food processing, pharmaceutical and chemical industries, have not been successful in achieving similar or significant acceptance within the minerals industry. The current biotechnical revolution coupled with its expanded understanding, dictate that a flagging minerals industry reconsider the use of biotechnology in metallurgical applications. Living resources, either singly, in commensal association or in complex communities, are capable of duplicating fully integrated and complex processing functions. Organisms can mine and extract metals, detoxify chemical effluents and synthetically produce compounds. They have been criticized as exhibiting poor kinetics, excessive energy consumption and environmental sensitivity. However, expanding knowledge reveals that these organisms are surprisingly adaptable, variable and extremely durable. Applied biotechnology in specific cases offers favorable economic returns, environmental benefits and aesthetic value. Selective implementation of living systems can offer opportunities for reduced labor, increased productivity and technological advance. Success will not come easily. Capital must be risked, controversial decisions made and new ground plowed. Traditional, specialist thinkers will of necessity give way to interdisciplinary expertise and unorthodox methodology if success is to be achieved. Those who vigorously persevere, however, are likely to be rewarded with a dynamic and profitable new role in a restructured minerals industry.

Jan 1, 1985

By Maurice Jackson et a1

Golder Moffitt and Associates (GMA)", were commissioned to reassess a large metallic low grade orebody. One of the aims of the study was to estimate recoverable reserves. Recoverable reserves are here defined as ore reserves for a specific mining block size. The mining block is that block on which the decision that the material is ore or waste is made. Recoverable reserves take into consideration mining methods. New methods for solving this type of problem were recently developed in Geostatistics and so for this reason GMA called for the technical assistance of the Centre de Geostatistique (C.G). The complete estimation was done using the geostatistical techniques and programs of the C.G together with some of the programs of GMA. As the mine was in production at the time the study commenced it was-possible to make frequent checks on the estimated values using blast-hole data. The ore reserves were also estimated using the more conventional interpolation method of inverse square of distance weighting.

Jan 1, 1979

By Adrian Smith, Debra W. Struhsacker

There is now overwhelming evidence that, despite concerns to the contrary, natural degradation of cyanide and cyanide attenuation by hydrogeochemical processes are capable of minimizing or eliminating potential water qua1ity impacts from heap leach systems. A1 though there was some recognition of these data by the regulatory authorities, for example the initial USEPA modification of cyanide standards to an advisory level, many states have codified standards inappropriate to the clearly site specific nature of heap leach operations. As an overview to this problem, this paper will integrate the theoretical chemical data on cyanide with the observed geochemical behavior of cyanide in the decommissioned heap leach environment. The cyanide species that are likely to exist within an abandoned heap leach system will be identified, and the relative toxicity and potential environment effect of these cyanide species will be discussed. These data will then be used to evaluate cyanide detoxification regulations for decommissioned heap leach projects in 14 states.

Jan 1, 1987

Over the past few years, the School of Mines of Paris has carried out a program of research* on the grade-tonnage relationships in the border zones of porphyry copper deposits. The initial problem was quite difficult : how does the grade vary at the border of the known orebodies? Does it decrease regularly, or do some thresholds exist, where the grade diminishes abruptly? The answer to these questions have important repercussions on the prediction of the future reserves in the fringe of the orebodies. If the grade decreases regularly, very important reserves could exist; if not, there would be strong limitations to the possible recoverable reserves. The first step of our study was a critical study of previous work done on the subject. It appeared that, following Lasky's pioneering paper (Lasky, 1950), most of the authors used what we can call an historical approach to the problem. In this, the grade-tonnage relationships are calculated from the available figures for production and reserves and the results are then extrapolated to the future. The strong limitation of this model are brought out in this article.

Jan 1, 1982

By I. Iwasaki

As the world tension relaxes and as the interest and taste for consumer products change, complacency is beginning to prevail over the needs of minerals and primary metals. The current trend towards resources and energy conservation calls for miniaturization of consumer goods, and lowers the demand for virgin materials to produce goods and services. Challenged by the third world countries with high grade ores and low labor costs, industrialized nations with lower grade ores are being pressed into more efficient operation through technological innovation, while protecting the environment. In many countries, domestic mines were forced to close since the oil crises due to rapidly rising energy and labor costs. Research in conventional mineral processing needs to be directed towards breakthrough technologies in order to maintain the competitive edge in the global marketplace. Research activities will provide new challenges in the processing of solid waste and waste water for environmental remediation as well as for resource conservation, in the preparation of new functional materials of extreme purity and/or unique properties for high technology applications and in the development of such future resources as deep sea minerals and extraterrestrial materials.

Jan 1, 1995