Search Documents

By L. D. Gehi, A. W. Khair, M. Ahmad

This paper presents an analysis of the dynamics of bit wear on the productivity of continuous miners. Two field surveys were carried out. The first survey assessed the impact of bit wear on productivity and production cost. The second survey studied the wear characteristics of the cutting tool (i.e., magnitude, forms, and mechanisms of bit wear, Primary factors affecting bit wear were identified. Laboratory experiments were carried out to study in detail the effect of some of these primary factors on wear. Results indicate, that bit wear has a significant effect on the productivity a continuous miners. Furthermore, under severe geologic conditions (i.e. cutting rock partings in roof and floor) bit wear not only hampers the productivity, but also increase the production cost due to a higher consumption of bits. This study also indicated that beyond 20% of the conical height loss (which corresponds to 7% of the weight loss) the rate a bit wear accelerates. This increased rate of wear is an indication of higher abrasion between bit body and cutting material, resulting in a dustier environment.

Jan 1, 1995

By A. Choudhury

Deep open-pit mines are becoming increasingly common in the highly mineralized arctic and sub-arctic regions. Air inversion is a frequent occurrence in these regions, and is exacerbated by complex geometry of the open pit and the surrounding natural topography of an open-pit mine. The resulting inversion cap is known to contribute to the degradation of air quality in the open pit, resulting in loss of production. This paper discusses the development and validation of a three-dimensional model that simulate the flow of air and the transport of gaseous contaminants in an arctic open-pit mine and the analyzes effect of the geometry of the mine and the slope angle of the pit on the contaminants profiles in the mine.

Feb 27, 2013

By M. K. Gangal, E. D. Dainty

The paper describes the capabilities of a micro-computer-based real time data acquisition system for monitoring and control of mine environments. Applications of such a system for monitoring the ventilation and air quality of a mine is outlined. The paper discusses the results of running a monitoring system with various environmental sensors in a simulated mine environment. The sensors used in this study are: carbon monoxide (CO), carbon dioxide (C02), nitric oxide (NO), nitrogen dioxide (NO2), sulphur dioxide (SO2 ), methane (CH4 ), air flow, absolute pressure, temperature and relative humidity. A performance evaluation of the monitoring system and sensors is presented.

Jan 1, 1987

By J. Pang, S. Chander

The results of an investigation to characterize the chalcopyrite/solution interface are presented. Several techniques were used, including galvanostatic and steady-state polarization, cyclic voltammetry and impedance spectroscopy. The results show that the dissolution of chalcopyrite was incongruent. Initially, at low potentials (< 0.12 V), iron species were released that led to the growth of an iron-deficient sulfide (IDS) layer (referred to as the "reacted layer" in this paper). Depending on the solution&apos;s composition, the dissolved iron might reprecipitate as a hydroxide layer. In the potential range of 0.12 V < E < 0.23 V, the IDS layer was passivating. In comparison, development of a passivating IDS layer under galvanostatic conditions led to a jump in potential to 0.48 V. The IDS layer began to dissolve at potentials greater than 0.24 V. The dissolved species precipitated to form a product layer in alkaline solutions. Continued oxidation involved diffusion of species through the reacted and product layers. At higher potentials (> 0.48 V), further oxidation led to the dissolution of the copper and sulfur species, with a resultant breakdown of the IDS layer. The changes in surface-coating properties, resulting from various electrochemical treatments, are discussed.

Jan 1, 1993

By William Petruk

Performance assessments are carried out to monitor operations, to evaluate performance and to identify processing problems. The assessment involves collecting and analyzing representative samples from critical points in a flowsheet and interpreting the data. Sample analysis techniques include chemical analyses, mineralogical investigations, mineralogical analyses, and materials balancing. Chemical analyses provide the lowest cost assessment and should be used liberally, particularly in monitoring a process. Materials balances performed on chemical assays for a suite of samples are used as a first step in evaluating a process. Mineralogical investigations are more expensive than chemical analyses but need to be used only at the beginning of mining and metallurgical operations and as a second step in assessing processing problems. Quantitative mineralogical analyses combined with materials balancing provide the most complete performance assessment, but the procedure is expensive. On the other hand, the assessment has the potential of a large payback when carried out where warranted.

Jan 1, 1991

By H. P. Schlanger, L. Paterson, B. H. G. Brady, B. E. Hobbs

A novel principle for a waste repository, based on a backfilled thermosyphon as the functional unit, is proposed. Such a unit reduces temperatures and temperature gradients in the vicinity of a waste package and in the repository near field, reducing leach rates from packages and thermomechanical disturbance of the rock mass. Preliminary analyses confirm the mode of performance of the system, and reveal some interesting features of material transport and sealing in backfill and rock fissures. The thermosyphon combines attractively with the prospect of developing a near-field geochemical trap with chemical specificity for radionuclides. It is proposed that a thermosyphon repository may provide superior performance of engineered and natural barriers compared with conventional designs. The achievement of the ability to predict accurately the performance of the thermosyphon, relative to other isolation schemes, will represent a benchmark in the understanding of the absolute performance of any repository.

Jan 1, 1986

By L. G. Austin

Using an instrumented laboratory high-pressure grinding rolls mill, the grinding force, gap dimension, mass flow rate and net mill power were measured for six coals and a crystalline quartz. A technique was developed to estimate the compressive stress-strain curves for compression of the materials in the mill plus the effects of elastic decompression. To reconcile the mill power and grinding pressure results, it was necessary to allow for the energy recovery on decompression. No clear correlation was obtained between the form of the stress-strain curves or the variation of specific mill power factor with the Hardgrove grindability index (HGI), although coals with the lowest and highest HGIs (i.e., 44 and 106) gave results significantly different from the other coals. Feeds below 140 mesh (105 µm) flowed more rapidly than coarser feeds and would not build up high grinding pressures. This indicated shearing and fluidlike properties rather than compression as a locked bed.

Jan 1, 1998

By S. I. Nozhko, V. N. Guliy, A. A. Zolotarev, L. M. Luyshnia

The study of the apatite deposits of the Aldan Shield shows wide spread of the Precambrian apatite-carbonate ores and possibilities of using them for extraction of apatite. Dependency of flotation on ore minerals was studied according to the following scheme: preparation of the monomineralic samples of anhydrite, gypsum, chlorite, serpentine, phlogopite, apatite; mixing them in apatite ore of the average composition; followed by flotation. Another series of the experiments was conducted to ascertain a dependence of flotation activity of the different minerals on the different flotation reagents, which were used as collectors. It has been shown that apatite from silicate-carbonate ores is most extractable because it has the biggest size of grains and is the most free of inclusions. Beneficiation of the sulphate-containing apatite-carbonate rocks is possible when flotol - 7.9 is used as a collector. Meanwhile, the use of the tallaktam leads to an increase in the sulphate recovery. The estimation of individual technological features of the layered Mghydrosilicates and their influence on the process of beneficiation has been examined using samples of apatite-dolomite ore (P205-8%) with the addition of the phlogopite, serpentine and chlorite. The results show that there is little influence of the chlorite presence on the flotation while the serpentine presence leads to a decrease of the flotation, because of its high specific surface area.

Jan 1, 1993

By S. Frimpong, D. Ali

For achieving bulk economic excavation, large dump trucks are being used in majority of the earth moving operations resulting in high impact shovel loading operations (HISLO) which exposes the operators to high levels of whole body vibrations (WBV). As the truck ages, hydro-pneumatic suspension struts loses their capability to effectively attenuate the vibration. A system is required to monitor and predict the performance of the suspension struts in real time. Machine learning and artificial intelligence (AI) has been applied for modeling and predicting the suspension system performance for lighter/smaller vehicles. However, no work has been done to implement machine learning or AI for modelling and predicting the performance of hydro-pneumatic struts in large dump trucks. Therefore, current work is going to be a pioneering effort towards developing machine learning and AI models for solving this problem. Support vector machine (SVM) and regularized dual non-linear regression has been implemented in order to achieve the goal. 3D virtual simulator for CAT793D was used to conduct experiments in MSC.ADMAS environment. The two main recorded outputs were the RMS accelerations in the vertical and horizontal directions at the operator seat for characterizing the performance of the suspension system. During the development and the training of the models, eighty percent (80%) of the total experimental data was used and the remaining 20% was used during the testing and validation of the developed models. SVM model showed the desired accuracy in terms of hydro-pneumatic suspension system performance prediction for large dump trucks. These models can be implemented in the dump truck controller which can then be used to monitor the performance of the suspension system in real-time, and with that proper maintenance and/or replacement can be scheduled by the maintenance personnel. Workplace safety, operator’s health and the overall system efficiency can be greatly improved with an implementation of such an intelligent system. INTRODUCTION Large capacity dump trucks are being employed in any earth moving operation throughout the world for achieving bulk economic excavation [1, 2]. A large dynamic impact force is produced with large capacity shovels dumping material weighing 100 tons or more in to the dump truck under gravity. This dynamic impact force generates high frequency shockwaves which travels throug0068 the truck body, chassis and reaches the operator’s cabin and thus exposes the operator to severe levels of whole body vibrations (WBV). Recommended safe limits have been listed by the International Standards Organization (ISO) in sections 1, 2, 4 and 5 of ISO 2631 (1997, 2003, 2001 and 2004). An operator can got through a long term back, shoulders, arms and neck disability and disorders if exposed to the WBV levels beyond those limits. The dynamic impact force generated as a result of the high impact shovel loading operations (HISLO) was modelled by Ali and Frimpong [2]. Furthermore, the complete methodology for optimizing the dumping process and reducing the impact force has been provided by Ali and Frimpong [1]. The vibration attenuation system present in the dump truck requires improvement in addition to the dumping process optimization. The vibration attenuation system in the dump truck commonly consists of hydro-pneumatic suspension struts. As the dump truck ages, its suspension system deteriorates and therefore loses its capability to effectively attenuate the shockwaves and the resulting vibrations produced by the dumping process. The deterioration tales place due to the contamination of the hydraulic oil or oil and nitrogen mixing or due to the gas accumulator diaphragm rupturing. The monitoring of the output vibration levels can be used to evaluate the effectiveness of any suspension system. With the dump truck suspension system, the vibration levels at the operator’s seat can be used for the evaluation of the effectiven

Jan 1, 2019

By R. V. Ramani, R. Srikanth

A three-part study was conducted to relate the dust generation propensity of a coal sample, defined here as the dust generation rate (grams of dust generated per tonne of coal broken), to its characteristics, in order to rank coal seams according to their respirable dust generation potential. In this paper, the results of a single breakage study on a variety of coal samples encompassing all coal ranks, and samples from operating mines are discussed. Further, where data are available, the primary dust generation rates of coal samples collected from underground coal mines are compared with the in-mine dust generation rates. The results of this analysis are then used to apply the results of this study to longwall face ventilation design. Vitrinite reflectance, and level of organic metamorphism are highly correlated with primary respirable dust generation rates of bituminous coal samples. The dust generation rates in underground coal mines are an order of magnitude higher than the primary dust generation rates in the laboratory. Depending on the type of coal, production rates, and dust control procedures, the air quantity required for airborne dust control can vary significantly. The air quantities on some high production longwalls are approaching the limits beyond which it may not be possible to reduce ambient ARD concentrations to less than 2 mg/m3 by dilution ventilation alone. In these cases, the miner&apos;s exposure should be controlled through the use of personal protective de- vices and administrative practices.

Jan 1, 1997

By Christopher Haycocks, Lawrence P. Johnson, George M. Neall, James M. Townsend

INTRODUCTION Conventional roof support methods such as mechanical and resin bolting provide adequate support for a wide variety of coal mine roof conditions. However, roof falls remain the single largest cause of death and injury in underground mines and seriously hamper production in many operations, demonstrating that these methods of roof support are not universally effective. One of the most recent and successful advances in coal mine roof control has been the introduction of the roof truss. Although past work on roof trusses (Gambrel1 and Haynes, 1970; Sheory, et al, 1973) shows little quantification of this support technique, numerous field examples have been cited where the truss effectively supported roof which could not be controlled by either mechanical or resin bolts (Kegel, 1969). The truss combines the advantages of both inclined roof bolts and post-stressing the roof. However, the full benefits of roof trusses will only be realized when design criteria to optimize support capacity are determined. The number of trusses required for a given roof condition can then be minimized, reducing installation time and making them economically more feasible. The purpose of this research is to develop roof truss design criteria based initially on laboratory studies of gravity-loaded multi-layered photoelastic mine models. Laboratory test results will then be modified where necessary following future field testing. The ensuing relationships should provide the field engineer with a reliable means of calculating optimum truss configuration, capacity, and spacing for a set of known roof conditions.

Jan 1, 1977

By R. S. Ondrey, R. A. Haney, T Tomb, R. T. Stoltz, Novakowski D. L. Chiz, E. J. Gerbec, D. J. Atchinson

Although the number of operating longwalls in the United States (approximately 100) has remained relatively constant over the last five years, longwall production levels have significantly increased and in some cases more than doubled. As a result of this production increase, control of respirable dust continues to be a problem. Therefore, the Mine Safety and Health Administration (MSHA), Pittsburgh Health Technology Center, Dust Division, initiated a study to investigate the availability and adequacy of technology for controlling dust on longwall mining operations. The study involved 23 longwall mining operations in three different Coal Mine Safety and Health Districts. Each operation was visited for a full shift. Respirable dust samples were collected on face personnel and at fixed locations along the face. Methods being used to control dust were noted, with special emphasis placed on obtaining quantitative data relative to ventilation, headgate dust controls, cutting drum sprays, external machine sprays and cutting sequence. Attempts were made to correlate dust control practices in place at the time of the visit to dust concentrations measured at the tail and on the tail shearer operator and to the average of all the dust concentration measurements from the occupations sampled. The methods used to control dust were also compared to the gamut of methods known to be available. This paper presents a discussion on the effectiveness of the methods being used to control dust and on the availability of technology for the control of dust on longwall mining operations.

Jan 1, 1991

By Peikun Liu, Guangyu Sun, Raja V. Ramani, Shambhu Sharan, Raman Srikanth, Bharath K. Belle

The contribution of the various outby sources to the contamination of the panel intake air has been the subject of a relatively small number of studies. In this paper, after a brief review of past studies, results from recent experiments on rates of contamination of intake air by outby dust sources are presented. Present study indicates that each outby source by itself may not be a major contributor. The loading point in the continuous miner section did not appear to be of major concern from contamination point of view. Belt entry including transfer point contributes significantly to the intake air dust level, though reentrainment was not a major source of dust. In longwall panels, the stageloader-crusher was the most dominant source. The panel-to-main belt transfer point was not a major source. Taken collectively, the contribution of all outby sources can be significant. In one longwall section, at the beginning of the longwall face, the contribution of all the outby sources and the headgate cut-out operation was observed to be about 80% of the permissible exposure limit (2 mg/m3). In modem high production longwalls, the application of effective dust control measures to reduce the dust generated from the outby sources is essential to achieve compliance with the dust standards.

Jan 1, 1997

By Robert M. Belesky, H. R. Hardy

A methodology to detect the presence and monitor the stability of shallow cavities is presented in this paper. The approach incorporates surface-wave seismic and acoustic emission/microseismic (AEIMS) techniques. Application of tomography to the seismic data is made to enhance the ability to locate cavities. Zonal and hit-sequence location techniques are introduced into AE/MS monitoring schemes. These source location techniques simplify the analytical procedure yet still provide sufficient information regarding the region of AE/MS activity. The concept of unique velocity data for conventional, least-squares, source location routines is discussed. A hypothetical case utilizing the algorithm is presented. The method described has been successful based on preliminary studies. Areas of current and future research are identified.

Jan 1, 1986

By A. LaPlante, A. Cauchon

This gravity circuit at Les Mines Camchib Inc. consists of two pinched sluices to bleed a feed to one of two 76 cm (30") Knelson concentrator. The Knelson concentrate is upgraded to smeltable grade with a smaller Knelson (18130 cm) and a riffleless table. Their tails are column cyanided and washed prior to recycle to the grinding circuit. This paper details size- by-size circuit performance. The Knelsons recover around 90% of free gold (as determined by Mozley Laboratory Separator), even below 37 pm. The sluices are ineffective, with upgrading ratios around 2, but approaching unity in the fine sizes. Much of the effectiveness of the circuit lies in the high gold circulating loads in the grinding circuit, which partly atone for the poor sluice performance, and the ability of the Knelsons to recover free gold. Secondary upgrading recovers slightly above 99% of the primary concentrate gold, 90% of it in a 65% Au concentrate and the balance in a heavily loaded (10 to 20 oz/st) pregnant solution, generated by intensive column cyanidation.

Jan 1, 1990

By William P. Diamond

Production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 m&apos; to 10.1 x 106 m3. Peak production rates were generally about 0.03 to 0.06 x 106 &/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to several factors including: completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance, is hole location. Holes on the ends of the panels, where overburden strata are in tension due to the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location which is in compression. Analysis of gob gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 1995

By M. J. Richards, T. X. Ren

Determination of the state of an underground fire plays an important role in fire fighting, rescue and reopening operations. This is normally achieved by the analysis and interpretation of fire gases taken from the fire zone. However, drawing conclusions from gas analysis is not an easy task and needs specialist skills, expertise and experience that are usually beyond the knowledge of the officials in a mine. The complexities of a mine fire and the uncertainties of available information often make effective fire fighting decisions difficult if not impossible. This paper describes a knowledge based expert system that can aid in the diagnosis of sealed coal mine fires. Using a commercially available shell, the expert system has been designed to accommodate a series of diagnostic rules replicating the reasoning logic that would be used by human experts. The system allows the diagnosis of explosibility of the fire zone and trends of various fire ratios to be easily visualised for decision making. By continuously analysing the incoming information, the system is able to provide a rapid assessment of the situation of a sealed mine fire prevailing under specific mining and geological conditions. In addition, short term trends in fire behaviour can be predicted and possible fire control actions recommended. An example is given and shows how this system can be used as an analytical tool in various ways to assist the combating of coal mine fires. Further development of the system is discussed.

Jan 1, 1993

By Michel L. Bilodeau

Mineral exploration is a sequential information gathering process. Primary exploration programs filter favorable areas through a series of geological, geochemical, and geophysical tests resulting in the discovery of mineral occurrences. The most favorable of these discoveries provides economic justification for a delineation drilling program. The purpose of delineation drilling is to provide information for estimating relevant physical characteristics of the mineral occurrence. These estimates are used to evaluate the exploration project and, eventually, the economics of mine development. Delineation drilling normally completes the exploration process. If the assessed economic characteristics of the delineated occurrence provide justification for mine development and production, an economic mineral deposit is the end result of the exploration process. Subsequently, a development drilling program is initiated to obtain the necessary data for detailed mine planning. The delineation drilling stage is in itself a sequential investment process. As delineation information accumulates, the reliability of geological estimates is improved and, thus, the uncertainty associated with the assessment of profitability criteria is reduced. Delineation drilling should continue as long as the marginal benefits, which result from improving the reliability of profitability criteria, exceed the marginal costs associated with the additional drilling.

Jan 1, 1979

By Randal J. Barnes

There are many methods available for the estimation of geologic parameters (Popoff, 1966; Barnes, 1980). In the last decade a new and relatively sophisticated technique using statistical theory has emerged: geostatistical kriging (David, 1977; Journal and Huijbregts, 1978; Rendu, 1978). An interesting property of geostatistical estimation is that when a geologic parameter is estimated for a given volume, not only is the estimate generated but an associated measure of certainty is produced as well. This statistical measure of estimation confidence is called the estimation variance. While the concept of an estimation variance is universally considered to be a good idea, mining engineers and geologists do not currently have the tools to incorporate it into their planning and quantitative analysis. This paper attempts to develop and present some of the necessary tools required to incorporate estimation uncertainty into mine planning. Geologic uncertainty is portrayed as an economic business risk. This risk is objectively characterized, and-the associated cost is quantified. Geologic delineation sampling is viewed in this light as an economic commodity with an associated cost and value. A coal mine planning example is used as a focus in this presentation. The data used is real, though it has been modified to maintain data security and project anonymity.

Jan 1, 1986

By Zhongxue Li, Shuang Gao, Zhixin Zhen, Yiqing Zhao, Xuan Qin

If not well-managed, a mine-tailings facility may become a major source of risks, endangering the community and environment, and damaging the reputation of the minerals industry regarding sustainability. Identifying, characterizing, and mitigating the hazards and risks associated with tailings facilities have been critical to the maintenance of community-safe and environmentally sound mine-tailings facilities. Herein, a complex network model for characterizing the hazards and risks associated with the lifecycle of tailings facilities is presented. In this approach, the hazards are modeled as vertices of the complex network, and the interactions among the hazards are modeled as edges of the complex network. The complex network for modeling the hazard and risk spreading of mine-tailings impoundments is analyzed and characterized by using network metrics such as the network density, geometrical characteristics, characteristic path length, network efficiency, and clustering coefficient. The degree distribution of the network obeys a power-law distribution, indicating that the network for characterizing the risk spreading associated with a tailings facility is scale-free. According to the results of calculations and existing research results, the network is ultrasmall-world. By analyzing the change of the global network efficiency under four kinds of different methods to remove network nodes and edges, network nodes with higher between centrality (BC) are identified as critical. The removal of those critical nodes helps mitigate risks associated with a tailings facility and reveals the vulnerabilities to BC attacks.

Jan 1, 2017