Search Documents

By Yoshinori Shimada, Oleg Kotiaev, Hiroaki Sakamoto, Toshihiro Asakura, Naotoshi Yasuda, Norikazu Misaki, Masahiro Shinoda

"To ensure that trains run safely, the performance of railway civil engineering structures is checked by periodic inspections. General inspection method has merits and demerits, but none of them offers the combination of high accuracy and quick inspection. In an effort to resolve this problem, West Japan Railway Company, the Institute for Laser Technology and the Railway Technical Research Institute jointly developed a remote laser sensing system as an alternative to the impact acoustics method for detecting defective concrete elements in tunnel linings. The proposed remote laser sensing system has two lasers, one to apply an impact to the concrete surface and the other to measure the vibration of the concrete generated by the impact laser. The impact laser is a high-energy pulse laser that induces vibration in the concrete. The detection laser has a signal beam and a reference beam. The signal beam reflects on the concrete surface and goes into the dynamic hologram crystal. The reference beam diffracts in the dynamic hologram and enters the detection sensor with the signal beam. The vibration of the concrete surface can be measured to detect the movement of an interference pattern. A prototype of the remote laser sensing system was developed as shown in Figure1. A vibration and acoustic insulators are equipped to remove a noise generated from a maintenance car or electric generator in this system. The proposed laser remote sensing system and the detection algorithm were verified with the help of field test conducted in a tunnel on the Shinkansen. An impact test using hammering was applied to obtain the accurate response acceleration on the surface of the concrete before application of the proposed method. In this test, the result obtained from the proposed method has good agreement with that obtained from the impact test by hammering. Consequently, it is verified that the proposed method can be used as an alternative to the standard impact acoustics method."

Jan 1, 2016

By H. P. Knudsen

In most open pit gold mines ore waste selection is based on estimates made from blasthole samples. These estimates frequently are biased. While it is true that high grades and "outliers" can induce a bias they may not be the only reason for the persistent bias seen at many mines. This paper focuses on a source of the conditional bias. In this paper it is shown that the poor blasthole sampling can cause a conditional bias in the estimates.

Jan 1, 1991

By S. Gallagher, A. Mayton, R. Merkel

The prolonged exposure of equipment operators to shock and whole-body vibration (WBV) is linked to cumulative back, neck and abdominal disorders. In low coal mines, space restrictions make it difficult for seat suspensions to isolate operators from shock and WBV. Researchers at NIOSH's Pittsburgh Research Laboratory are responding to these issues by investigating viscoelastic foams. For the full-load case, an ergonomic seat made with viscoelastic foams can isolate the shuttle-car operator from shock at 15 Hz. Researchers used results from additional foam testing using an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

Jan 1, 2000

By Kenneth S. Graham, S. C. Gambrell

A short term, simple roof bolt load cell which uses a birefringent (photoelastic) coating as its sensing element has been developed. The load cell is installed between the bearing plate and the nut/washer and measures the initial force after installation by the bolting machine. The load cell can be removed from the bolt and used again to measure initial force in another bolt if desired. Because temperature and humidity changes in the mine cause creep/relaxation of the coating and/or adhesive, the load cell is useful for accurately measuring force for a period of only two weeks after installation. Force in the bolt is determined by referring to a calibration curve for the load cell.

Jan 1, 1992

By Normand Tassé

Reactive barriers, which consume oxygen, are prospective though unconventional alternatives to physical barriers for Acid Mine Drainage prevention. However, a reactive barrier implies a problem of duration. Pore gases were analysed in several wood waste piles in order to understand the factors which control wood degradation and help to determine the effective life span of such a cover. Long term efficiency seems to strongly depend on the degree of water saturation at the bottom of the pile, likely because the development of a microbial biomass in such an environment helps to keep the amounts of nutriments and readily metabolizable organic substrates at a high level, which in turn promotes oxygen consumption.

Jan 1, 2000

By K. N. Han

The kinetics of gold dissolution in iodide solutions with oxygen in an autoclave was investigated. The leaching process was described by a gas-liquid-solid heterogeneous reaction. The effects of stirring speed, temperature, oxygen partial pressure and lixiviant, concentrations on the overall leaching rate was investigated. It was found that the dissolution of gold could be represented by a heterogeneous chemical reaction. Under the conditions studied, the apparent activation energy ranged from 34.7 to 54.3 kJ/mol. Experimental findings were in good agreement with the kinetic model proposed.

Jan 1, 1998

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Caterpillar 994 Class) for use as primary loading equipment in open pit iron-ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Information was gathered on loader selection rationale; operation and maintenance experience; and production, availability and costs. Brief time studies were conducted to indicate machine performance and utilization. This paper summarizes the field data that was collected including an economic comparison of wheel loaders and cable shovels in an iron-ore application.

Jan 1, 1997

By Jorma Miettunen

The Plant. The annual production of the Pyhasalmi mine is 900 000 tons of copper- zinc-pyrite ore containing approximately 0.7 % Cu, 2.5 % Zn and 30 % S. During 1976...1981 altered surface ore, 850 000 tons in all, was also treated at the concentrator. The surface ore was crushed and ground in a separate plant and was then fed into the copper or zinc flotation or was flotated in its own circuit, depending on the degree of alteration and the content of copper and zinc in the ore. The surface ore was exhausted in October 1981. Flotation comprises three consecutive flotation circuits; copper, zinc and pyrite circuit. The zinc circuit includes an open circuit roughing and scavenging. The scavenger concentrate and cleaner tailing are pumped to the middlings flotation. Rougher concentrates of the open circuit and the middlings flotation are pumped to cleaning which includes four stages. Figure 1 describes the flowsheet of the zinc circuit.

Jan 1, 1982

By Mike L. Aziz, Keith D. Ferguson, Glenda Ferris

The Equity Silver mine has been a severe producer of Acid Rock Drainage (ARD) since 1982. The mine was closed in 1994 and a compacted clay cover installed, but ARD continues to be produced. Three permanent employees manage the collection and treatment system at the site. The site still poses a significant environmental risk to the environment and downstream users and requires a high level of diligence. Various stakeholders' perspectives of the risk posed by Equity, and what constitutes acceptable risk, will be examined in this paper from a company operation staff, corporate environmental manager and downstream environmentalist perspective.

Jan 1, 2000

By K. V. K. Prasad

Stochastic simulation has been routinely used for performing risk and sensitivity analyses in a variety of fields. The commonly used means of generating the simulations has been the Monte Carlo approach, which usually employs a Simple Random Sampling (SRS) scheme of the variable distributions. This method is prone to sample clustering and requires a large number of samples to represent the distribution faithfully. This can become problematic for simulating complex processes where it is impossible to run an arbitrarily large number of replicate simulations. The Latin Hypercube Sampling (LHS) method uses a stratified sampling approach that assures representation of the input distributions for any given number of samples. In this paper the LHS and SRS approaches are compared, using a petroleum resource estimation example.

Jan 1, 1994

By G. T. Adel

During the past decade, researchers at Virginia Polytechnic Institute and State University have worked to develop a novel flotation process for treating very fine particles. This process, which is now commonly known as [microbubble column flotation] (MCF), has been shown to be very effective in a number of applications related to fine coal processing. These applications include the retrofit of existing preparation plant circuits and the recovery of additional coal fines from refuse streams. In addition, work conducted under the sponsorship of the United States Department of Energy indicates that the MCF process is capable of producing superclean and ultraclean coals from many eastern U.S. coals. This paper describes some of the basic problems associated with fine particle flotation and the design and operational features of the MCF process used to minimize these problems. Also presented are the results of ongoing pilot- and field-testing programs.

Jan 1, 1989

By J. A. Organiscak

This paper examines methods for limiting occupational silica exposures for roof bolting personnel in underground coal mining. A canopy air curtain and an air tube were evaluated as means to provide filtered air over the breathing zone of these personnel. Laboratory testing showed that dust reductions beneath the air curtain and air tube approached 60 percent and 40 percent, respectively, with low interference air velocities. The data also showed that dust reductions were highest for positions closest to the device and that these levels decreased with distance. This paper also evaluates a metal rake, a flexible insert, and a rigid insert for cleaning the roof bolter dust collector box. Less dust was produced when using the rigid insert. Surprisingly, the flexible insert was sometimes no better than scraping or raking the dust onto the mine floor. However, little dust got on the coveralls when using either of the inserts.

Jan 1, 2002

By Stanislaw Nawrat, Waclaw Trutwin, Waclaw Dziurznski, Janusz Roszkowski

In recent years attempts have been made to fight open and intensive mine fires by the use of special extinguishers, which are able to produce great volumes of inert gases directed into the fire zone. These extinguishers are derived from turbo-jet engines used in aircrafts and adopted for operations in mine conditions. The purpose of this paper is to draw the attention to a computer simulation method, enabling studies of dynamical behaviour of mine ventilation processes disturbed by open fires, which are also influenced by measures taken during fire fighting actions i.a. the mentioned operating extinguishers. The first part of this paper gives an account of the principles on which the computer simulation program, concerning the non- steady mine ventilation process, the fire as a heat source and the extinguisher as a source of inert gas and moisture has been based. The next part of this paper deals with simplifying assumptions and the subsequent limitations of the derived simulation pro- gram. Finally, from an example of a computer simulation, the results will be presented and relations shown between parameters characterising the ventilation process during the fire fighting action.

Jan 1, 1997

By Ing Newton Amegbey, Joseph Afari Idun

Ashanti Goldfields Corporation (Gh) Ltd., the leading gold mining operation in Ghana is embarking on a major rehabilitation and expansion programme to increase gold production. A new southern ventilation district was targeted for this programme, and the ventilation system was to be reviewed in order to cope with increased production. The southern ventilation district was previously ventilated by booster fans. This arrangement was however, inadequate to solve the problem of the need to reduce smoke clearance time of the production areas, and to generally improve the underground ventilation conditions. Fan maintenance costs increased with the number of fans installed in the booster fan arrangement, and the fact that the fans were installed underground made maintenance difficult and took longer time. It became necessary to consider the installation of a new main fan on the surface. This paper gives an overview of the ventilation systems of the southern ventilation district of the mine before and after the new main fan was installed. The field tests carried out on the fan to ensure that it complied with supplier's specifications are described, and the new system analysed to see it's effectiveness.

Jan 1, 1993

By H. H. Murray

Tactical R & D is research and development for a specific application or applications. The mineral scientist has to define and understand the physical and chemical parameters required for a specific or potential application. Then the researcher must know the structure and composition of the mineral and its physical and chemical properties. Can these properties be changed by processing particle size and shape modification, and surface chemical treatment? Examples of tactical R & D in the industrial minerals area will be described.

Jan 1, 2003

By Paul J. A. Lever

The mine environment is dynamic and operating conditions change continually and are difficult to predict. New equipment, variable geological conditions, modified layouts, and different equipment operators make monitoring and control system difficult to apply without continual software maintenance. The paper reports on algorithms that were developed, encoded with Knowledge Craft Tools, and tested on underground coal mine data to adapt to the dynamic environment. The system receives data from sensors in near real time and then identifies patterns in the data. Using a set of mode features the data is automatically checked to determine the present operating mode. When the operating mode changes from the previous shifts, the system automatically learns the new mode characteristics and uses that mode context for further data analysis. The concepts presented in this paper are applicable to a wide variety of mining scenarios, not just underground coal mining.

Jan 1, 1992

By J. D. Miller

Flotation chemists have long sought to unravel the mechanisms of carboxylate collector adsorption by semi-soluble salt minerals. In particular, the adsorption density of adsorbed carboxylates, adsorption kinetics, speciation (chemisorbed, physisorbed), orientation, and conformation are of interest. Given the importance of these phenomena in establishing the hydrophobic state at a mineral surface, in-situ surface spectroscopy studies certainly are justified. Such measurements traditionally have been difficult to perform. However, beginning in the late 1980s, a Fourier transform infrared (FTIR) spectroscopic technique was developed that has allowed for the acquisition of a wealth of detailed information concerning carboxyiate adsorption in semi-soluble salt flotation systems. The technique, internal rejection spectroscopy using single-crystal internal reflection elements, is reviewed, as it applies to semi-soluble salt flotation systems.

Jan 1, 1999

By Erie F. Wolstenholme

The purpose of this paper is to describe work undertaken, within the System Dynamics Research Group at Bradford Management Centre, into the development and application of a System Dynamics model of an international mineral industry; aimed at providing a basis for analysis of the interrelationship of supply, consumption and price over time, under different production and stocking policies. A review is presented of some of the major characteristics and problems associated with such industries. This is followed by an outline description of the model and the way it has been applied to examine various supply responses, in the light of changing consumption patterns. Demonstration results deal with model validation and with analysis of international buffer stocks and conflicting supply policies on the historic situation in the copper industry.

Jan 1, 1979

By R. Hogg, T. F. Dumm

With increasing interest in the physical cleaning of fine coal, there is a need for extension of the sink-float analysis procedure to finer sizes. Problems arise, however, in ensuring complete dispersion of the particles in the heavy liquids. A procedure has been developed in which surfactants are wed as dispersing agents, and solids concentration is minimized (using a simple formula to estimate the minimum weight needed for statistical reliability). Using centrifuges to increase separation rates and subsieve particle size analysis of the specific gravity fractions, a complete size-specific gravity distribution can be obtained. Analyses have been performed on coal samples as fine as - 10 µm.

Jan 1, 1987

By R. D. Deister

The Buick concentrator represents state-of-the-art technology in automated digital process control operation utilizing a centralized computer. The process control strategies implemented at Buick are no longer new to the industry, but the successful application of these developments is still rather unique in North America. Productivity improvements, determined to be a direct result of the process control developments, are the primary topics of this paper. Emphasis is placed on metallurgical benefits including both lead and zinc recoveries; lead concentrate grade; and reductions realized in reagent consumptions, operating costs, and personnel. A detailed description of the concentrator, along with a history of the process control development and a more in-depth discussion of the control strategies implemented at Buick can be found in the references. (The Buick flowsheet is depicted in Fig. 1).

Jan 1, 1987