Search Documents

By Ian M. Loomis, Keith G. Wallace

The Waste Isolation Pilot Plant (WIPP) is a U.S. Department of Energy research and development facility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste. The waste storage horizon is 655 m (2150 ft) below surface in bedded salt. To date the WIPP project has not emplaced any waste. There are three intake shafts used to supply air to the underground. All air is exhausted though a single return shaft. The total design airflow during normal operations is 200 m3/s (424,000 cfm). The ventilation system is designed to provide separate air splits to construction, experimental, and storage activities. Separation is achieved by isolating the storage circuit from the construction or experimental circuits with bulkheads. Any air leakage must be towards the storage area of the facility. Field studies have shown that the pressure differential necessary to maintain the correct leakage direction is susceptible to the effects of natural ventilation; therefore, extensive studies and analyses have been conducted to quantity the natural ventilation effects on the WIPP underground airflow system. A component of this work is a monitoring system designed to measure the air properties necessary for calculation of the natural ventilation pressure (NVP). This monitoring system consists of measuring dry bulb temperature, relative humidity, and barometric pressure at strategic locations on surface and underground. The psychrometric parameters of the air are measured every fifteen minutes. From these data, trends can be determined showing the impact of NVP on the ventilation system during diurnal variations in surface climate. Both summer and winter conditions have been studied. To the author's knowledge this is the first reported instance of automatic and continuous production of time and temperature variant NVPs. This paper describes the results of the initial monitoring study. INTRODUCTION The ventilation system at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico, is designed to perform two distinct functions. First, it supports normal mine ventilation requirements complying with all state and federal mine regulations. Second, the system is designed to prevent an uncontrolled release of radioactive contaminants from the storage and transportation areas of the facility. Although a nuclear radiation release in the facility is considered unlikely, many special features are implemented in the ventilation system to prevent the possible spread of contamination. The facility is constructed with the waste transportation and storage areas separated from the mining and non-radioactive experimental areas. The ventilation system is designed such that air leakage is from the mining and experimental areas to the storage areas. Furthermore, radiation detectors are located throughout the storage and waste transportation areas underground and an exhaust filtration building is installed on surface to prevent the possible release of radiation to the environment. For over two years the underground ventilation system has been rigorously tested and balanced. It was during this period that the adverse effects of NVP were noticed and subsequently quantified. From extensive field studies and computer models, several mitigating features were designed and constructed and special operational procedures were implemented to control the impacts of NVP. To quantify more accurately the NVP at the WIPP, a continuous monitoring system was installed. This monitoring system consists of measuring dry bulb temperature, relative humidity, and barometric pressure every fifteen minutes at strategic locations on surface and underground. From this psychrometric data, the NVP is calculated. Fan operating pressures and flows and strategic differential pressures are recorded from the site Continuous Monitoring System (CMS). The monitoring system provides a means of evaluating how the ventilation system behaves in regard to climatic conditions and to judge the efficacy of the mitigating features and operational procedures. To the author's knowledge, continuous calculation of NVP as a function of time and surface temperature has not been previously reported. Overview of the Waste Isolation Pilot Plant The U.S. Department of Energy determined that the plastic nature of bedded salt may provide the best solution to isolate transuranic (TRU) waste from the biosphere. Initial evaluations at the WIPP site began in 1974. In 1979, the United States Congress enacted Public Law 96-164 for the construction and development of the WIPP project. The mission of the WIPP is to demonstrate the safe, long-term disposal of TRU waste generated by the national defense programs of the United States. TRU waste is classified as a low to medium level waste. The waste is stored in drums and does not produce significant heat (not greater than 1 W per drum). The WIPP site is located approximately 47 km (29 miles) east of Carlsbad, New Mexico in the Chihuahuan Desert. The repository is located in the 630 m (2000 ft) thick Salado Formation. This Permian Basin salt deposit is about 225 million years old and appears to have been minimally disturbed by earthquake, faulting, and ground water activity since it was deposited. The underground facility is 660 m

Jan 1, 1993

By William P. Shinn

The site of Pittsburg from the first knowledge by white men of its location has been regarded as a position of great strategic importance.

By P. D. Pattillo, J. B. Cheatham, Y. -H. Lin

The stability of a hemispherical cavity, intended to model a perforation opening in the vicinity of a borehole, is analyzed for the case of poroelastic-plastic material behavior. Two plasticity models of differing complexity are considered, with the emphasis in either model being the use of strain softening to calculate inelastic stiffness. Sample results illustrate the effect of steady fluid flow on the response, and possible collapse, of the near perforation region.

Jan 1, 1986

By R. S. Das, A. K. Sinha

Modern mine ventilation systems have grown rapidly in recent years both in terms of complexity and value for human health and safety. Although computer models are now available to help the design and operation of mine ventilation systems, considerable differences often exist between the computer-based predictions and practical results. Research conducted to compare computer results with practical measurements made in ventilation circuits simulated in a physical model seems to confirm such differences. It is concluded that although a mine ventilation computer model is a very powerful tool, it can be utilized to its full potential only if reliable input data are provided.

Jan 1, 1987

By Jay Jones, William D. Rech

The Henderson Mine developed a water treatment system in 1985 to meet the NPDES requirements for its mine water discharge. Unacceptable levels of Zinc and Manganese formed the basis for the design and operation of the treatment system. Since initial start up, this system has reliably removed metals from the mine water and facilitated low cost compliance with water standards. The potential addition of a bio- monitoring requirement to the NPDES Permit in 1990 has added a second dimension to the metals removal process. This paper will review the history of Henderson's success at developing a low capital treatment system for metals removal and the anticipated effects of bio-monitoring upon this system based upon preliminary bio-monitoring screening.

Jan 1, 1991

By Dwayne K. Rowlett

A lysimeter designed to measure suction and collect a pore water sample from unsaturated waste rock has been developed and its performance has been verified in two large scale column tests. The test columns were constructed to bracket the envelope of grainsize curves for waste rock from Northern Saskatchewan. The suction profile within the columns was measured under a series of infiltration rates using tensiometers and these were compared to the lysimeter readings. The rate at which pore water samples could be collected was also measured under each infiltration rate. Lysimeter measurements of suction were found to be slightly lower than the tensiometers.

Jan 1, 2000

By Yoginder P. Chugh, K. V. K. Prasad, R. Missavage

This paper presents results of field monitoring and finite element studies to analyze and improve a room-and-pillar retreat mining system. Fie1 d instrumentation was utilized to monitor pi11ar load changes, roof to floor convergence and differential roof strata movement as retreat mining progressed and to determine in-situ horizontal stresses. A two-dimensional finite element model depicting strata behavior at this mine was developed and used to analyze existing and alternate improved mining geometries. The results showed excellent correlation between fie1 d observed and model predicted behavior. Some of the recommended changes in mining geometry based on the study were incorporated in the mining system.

Jan 1, 1986

By Arthur S. Cornford

According to Arbiter (Reference 1), the ball mill was invented by Brückner in Germany in 1876 and was first used in the United States on ores about 1905. The basic concept was a simple rotating cylindrical drum in which the tumbling action of the charge of material and grinding media resulted in size reduction of the material. Despite the very low mechanical efficiency of this method a number of factors have caused the tumbling mill to remain, by far, the most widely used piece of equipment for mineral grinding. The principal factors influencing this situation have been simplicity of design, ease of manufacture, ready adaptability to familiar material handling layouts and the absence of practical alternatives acceptable to the industry. In the early mills, the material was ground in batches, the mills being charged and discharged through doors in the shell. The shell was supported by means of solid trunnion shafts resting in plain bearings and the drive was accomplished through one of these shafts. In some later batch mills, the mill shell was supported on rollers which were also used to drive the mill. At an early stage, continuous operation was made possible by feeding and discharging the mill through hollow trunnions, the method still in most widespread use. The mechanical and structural design of the early mills was not an onerous engineering task. Norse sense and good practical knowledge were key qualifications. The mill shells had to be heavy enough to withstand the physical abuse they would receive in the field and the bearings had to have low enough unit pressures and sufficient wear retol to ensure several months of operation before the need for replacement occurred. When these requirements were satisfied, stresses developed in the equipment during operation were insignificant and the majority of structural failures were probably due to the use of inferior materials in manufacture. Over the years, the ever present demand for increased productivity has resulted in a steady Increase in the size of units of production equipment, including grinding mills. Arguments have been presented elsewhere, for and against the Idea of a high throughput single line grinding operation as opposed

Jan 1, 1972

By S. K. Mishra, S. B. Kanungo

Because conventional (physical) methods of ore dressing are not suitable for reducing the phosphorus contents of high-phosphorous manganese ores from Andhra Pradesh (AP) and the adjoining area in southern Orissa, India, the adoption of chemical methods becomes imperative. An attempt was therefore made to reduce the phosphorus content of partially beneficiated manganese ores from AP by roasting with sodium carbonate and then leaching with hot water. However, due to the higher phosphorus contents of the manganese ores from Nishikhal mines in southern Orissa, and because of their apparent resistance to dephosphorization by roasting with Na2CO3 alone, a mixture of Na2CO3 and NaCl was found to be necessary to reduce the phosphorus content to below 0.15%. Free-energy calculations at 700°C and above indicated that Na2CO3 (or Na2O as the active component) is a more active reagent than NaCl. Various process parameters, such as the temperature and time of roasting, the amount of sodium carbonate and the temperature and time of leaching, were studied to arrive at the optimum conditions for dephosphorization.

Jan 1, 2000

By Roshan B. Bhappu

In situ mining and extraction is one of the Frontier Technologies that is destined to play an increasingly important role in the recovery of metals and minerals in the future. This premise is based on increasing costs of labor and energy, increasing awareness of environmental considerations and decreasing ore grades in the United States. Up to now, in situ mining has been successfully applied to a few favorable situations for the extraction of some evaporites, copper and uranium. However, because of its unique technical, environmental and economic advantages, this versa tile technology will find broader applications for the recovery of above commodities as well as for others which are currently extracted by hydrometallurgical means. This paper traces the development of in situ mining and extraction; stresses its dependence on interdisciplinary science and engineering; discusses its theoretical, practical and economic aspects; and finally presents potential applications of this Frontier Technology.

Jan 1, 1985

By J. A. King, D. R. Weir, P. C. Robinson

Preconcentration of Porgera ore results in high recoveries of gold into gravity and flotation concentrates. The bulk of the gold is contained in auriferous pyrite flotation concentrate and is not readily recoverable by direct cyanidation. Oxidation in autoclaves at high pressure and temperature produces a residue that contains the gold in recoverable form. Pilot plant treatment of the autoclave residue is described, through washing and jarosite decomposition stages, to cyanide leaching and recovery of gold and silver by carbon-in-pulp techniques. The concern associated with disposal of plant effluents are also addressed.

Jan 1, 1987

Conventional logging tools such as density, neutron, and acoustic have ranges of investigation of tens of centimeters. The borehole gravimeter, however, has a range up to hundreds of meters. For example, from the center of a cylindrical ore body 0.20 g/cm3 denser than its surroundings, one can detect the boundary of the ore body at a radius as large as five times its height. More complex structures can be investigated with computer programs. We can predict the usefulness of proposed gravity surveys, or decide which suggested structure is most likely to have caused the results of existing surveys.

Jan 1, 1988

By Dirk van Zyl, Clint Strachan

A study was conducted to assess the feaeibility of increasing the heap height above one lift at the Alligator Ridge Mine. This study concentrated on the physical aspects of the heap and liner performance. Two principle aspects were addressed during this investigation: (a) the adequacy of heap permeability under present and future loading conditions; and (b) the adequacy of the liner to limit seepage losses. Field and laboratory test a were performed and their details and results are presented. It was concluded that the permeability of the heap would remain adequate for higher heap. The geometry of the heap will be the major constraint. It was also concluded that the liner would perform satisfactorily beneath higher heap.

Jan 1, 1987

By M. J. Laurila

Elemental analysis of slurry streams using X-ray fluorescence (XRF) has long been employed. However, detector technology has limited the application of XRF devices. Using detector technology employed on NASA's Mars Pathfinder to analyze soil samples, Process Control, Inc. has developed an on-line analyzer to mount on a sampling system. The prototype XRF elemental analyzer was installed at Detroit Edison's Monroe Power Plant in January, 1998 and has been employed to monitor feedstock quality. A slurry system has been developed for flotation control. This paper describes the testing of the analyzer using the new, draft ISO standard for evaluating the performance of on-line analyzers (ISO/DIS 15239).

Jan 1, 1999

By K. Chandrasekaran

Carbon-in-Leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. CIL process is becoming attractive even in other situations when preg robbing is not a factor. This paper discusses the situations in which the CIL circuit can be applied. The results of Leach/CIP and CIL circuits at Newmont's Mill No.2, 4 and 5 are presented for comparison. Newmont's Mill No. 4 was initially designed for a throughput of 4500 tons per day. The mill is presently operating at an average throughput of 7300 tons per day without significant changes to the original design. The design considerations of the Mill No.4 CIL circuit are discussed.

Jan 1, 1991

By E. J. Owen, A. Appah, I. C. Sanchez, K. T. Stafford, N. Hurtig, R. Otoo, N. A. Iverson, S. A. Moses, V. T. McLemore

New Mexico lies at the eastern edge of one of the world’s great metal-bearing provinces hosting numerous Laramide and Paleogene mineral deposits. Southwestern New Mexico contains Laramide porphyry Cu (±Mo, Au) and Paleogene Mo-W deposits. Porphyry deposits are generally large, low-grade deposits containing Cu, Fe, Mo, Au sulfides (and other metal sulfides) associated with porphyritic intrusions and exhibit characteristic alteration styles. Porphyry deposits can also be spatially and temporally associated with skarn deposits and polymetallic veins. All of these deposits have the potential to host various critical minerals, including Cu, Zn, Bi, Co, Ni, rare earth elements (REE), Te, and W. Critical minerals may be found as substitutions within ore minerals or as separate mineral phases. These deposits are constrained using 40Ar/39Ar dating into three ore-producing magmatic pulses: 1) ~78–71 Ma Laramide pulse, 2) ~59–50 Ma, Laramide pulse, and 3) ~40–30 Ma Paleogene pulse. New and historic whole-rock geochemical data have highlighted areas with critical minerals potential that require further study.

Feb 1, 2025

By Yixian Zhao

Although many ultimate pit limit design algorithms have been developed for the past one- quarter century, only the well known Lerchs-Grossmann's (LG) algorithm is capable of producing a truly optimum ultimate pit limit today. This paper presents a graph theory oriented algorithm for optimum ultimate pit limit design. This algorithm produces a true optimal solution and maximizes the total undiscounted net profit for a given 3-D block mine model. The algorithm performs much better than the well known LG algorithm, in terms of the reduction in computation time and computer memory requirements. More importantly the new algorithm is easier to understand and implement than the LG algorithm. Specifically, this paper discusses: 1) the computer representation of arcs and the rules of arc generations which dictate the formation of trees in the graph, 2) the mechanism of joint support and re-allocation, 3) the properties, the general procedures of the algorithm, and the suggested specific steps to implement the algorithm, 4) comparison between the new algorithm with LG algorithm, and 5) some experience in implementation of the algorithm and two case study results.

Jan 1, 1992

By G. D. Criswell, F. Palkovits, J. M. Johnson

A paste technology investigation was completed for non-pozzolanic fly ash from Units 3 & 4 of PPL Montana’s Colstrip Steam Electric Station. The purpose was to assess the feasibility of converting from dilute slurry deposition of ash products to a system using thickened or paste ash to reduce excess water storage in the impoundment, reduce seepage losses, and increase storage efficiency. The investigation included laboratory and field testing to characterize the rheological, geotechnical and dewatering properties of the ash products, an assessment of potential seepage reductions and an evaluation of potential for increased ash storage capacity by modifying impoundment operating procedures. The studies concluded that the conversion project was feasible, cost effective, and permittable. Critical facilities for the conversion project are currently under construction.

Jan 1, 2004

By John A. Herbst, Per-Olaf Samskog, Jan Bjorkman, Yi Chang Lo

The study described here is concerned with the development of a model for the simulation and optimization of a rod milllpebble mill circuit. A series of laboratory tests was conducted to investigate the effect of critical operating variables. The pebble mill model structure used was a population balance type which accounta for impact breakage and fines production from pebble wear. Model parameterization and verification were performed using data obtained in batch tests and in a plant test campaign. The model developed was found to provide accurate predictions of plant-scale grinding. The prediction errors are less than 21 for the product size and 31 for the mill power required to achieve that product with a mill volume scale-up of 14,000 to 1. These results indicate that accurate extrapolations from laboratory batch data to plant scale performance are poaaible using the population balance model and scale-up prediction procedures for pebble mill circuits as well as ball mills. Preliminary indications are that the new model developed here will provide vital input for pebble mill optimization and process control as well as pebble mill design.

Jan 1, 1990

By Franklin H. Sharp, R. Woods

The operation of the Magmont Concentrator located on the New Lead Belt of Southeast Missouri is described. Ore characteristics affecting lead-copper-zinc separation are enumerated, and the cur- rent methods of separation are detailed.

Jan 1, 1976