Search Documents

By G. C. Kachel

During the past two years, there has been an increasing acceptance of process automation among ferrous, non-ferrous and non-metallic rock processing operations in an attempt to keep total unit costs in line in a market situation where labor and material costs are rising almost daily. Previous technical papers (1) (2) (3) (4) (5) have described, in considerable detail, instrumentation and automatic control devices that have been successfully applied in a wide variety of crushing and grinding facilities. While many of the basic control philosophies that evolved almost ten years ago remain essentially unchanged, new components and devices have been developed during the past two years that permit these philosophies to be better implemented in operating plants. Some of these devices and their application will be discussed with particular emphasis placed in describing the basic control philosophy employed as well as some of the hardware or components comprising typical crushing and grinding circuit control systems. Before any instrumentation or automatic control system can be successfully devised for a specific facility, there must be a clear understanding and agreement by supplier and user as to the control system objective. In the case of a crusher feed rate control system, the objective is generally to maximize thru-put of a given finished product size. While this is often the case in a grinding circuit automatic control system, the reasons may be entirely different. Taconite processors whose end product is to be pelletized, generally attempt to control their grind within narrow limits to optimize balling action. Other milling operations are more concerned with obtaining metallurgical liberation and can, in many cases, tolerate wider swings in finished grind.

Jan 1, 1969

By Williams R. Reynolds

Studies of the northeastern Mississippi bauxites were initiated primarily for the purpose of ascertaining the quality and quantity of the ore. Subsequently, this ore was found to have a rather dubious economic value as was previously suspected but never established in earlier economic reports (1, 2, 3). However, the quality of ore was found to be higher than previously thought. Even though the ore bodies were determined during the early stages of this study to be too thin, small and widespread for commercial production a continuation of the study was not abandoned. On the contrary, the present investigation was intensified concentrating less on the economic application and more on stratigraphy and genesis. Considering the ever increasing demand for aluminum products the northeastern Mississippi bauxite district which includes portions of Tippah, Benton, Pontotoc, and Union Counties may soon become, in spite of inferior quantities of ore, an attractive area for bauxite production. Presently, however, the meager quantity of ore discourages exploitation. On the other hand, these northeastern district bauxites are facies of more extensive units of lignite bearing high aluminum clays, and considering the advances in aluminum extraction from clay these clays may in the future beckon mining interest. The bauxite of the northeastern Mississippi district, mapped as a part of the Betheden Formation (4). has an outcrop trend along the county lines of Tippah and Benton Counties and the extreme western portion of Union and Pontotoc Counties. Studies of exposures and cores stratigraphically positions the outcrop between the middle Midway Porters Creek Clay and the lower Eocene Wilcox sands and

Jan 1, 1977

By C. Konya, A. Konya

"INTRODUCTION Over the past twenty years this Linear-Regression Modeling has become widely accepted for ensuring limits are not exceeded at a site, using the Scaled-Distance variable. In today’s industry, numerous equations are present for different scenarios, geologic environments, hole sizes, and numerous other factors with an emphasis on site-specific equations developed for all major projects; however, underground blasting applications have not been analyzed to a great degree of detail. Without previous knowledge this puts underground blasting operations into a guessing-game to ensure that vibration levels are not exceeded. This paper will review two recent projects that have been worked on by the authors and linear-regression models that were used with both burn cuts and stope blasts. BLAST VIBRATIONS MODELING The first major research project conducted in the United States on blasting vibration was Bulletin 442 (Thoenen & Windes, 1942) which looked at the relationship between blasting and blast vibrations in the fall of 1940. This study examined numerous blasts and began the investigation into topics such as damping, structural damage from vibrations, frequency dependency on vibration, resonance vibration, delayed blasting, and numerous other factors. Bulletin 442 had two major conclusions which are: 1. The vibration from a blast can be predicted with a relationship of size of the shot and distance to the structure (now known as scaled distance) 2. “The vibration of a structure at resonance does not in itself cause damage because of the restraining effect of damping inherent in the building” (Thoenen & Windes, 1942) Due to the increase of blasting near homes and busier areas the USBM commissioned an additional study to further develop a few of the topics covered in Bulletin 442; this study would go on to be published as RI 6561 (Duvall, Johnson, Meyer, & Devine, 1963) with the study looking into delayed blasting and the relationship between charge weight, distance, and peak particle velocity of the blast. This relationship would be termed as the ‘scaled-distance’ and take the form of:"

Jan 1, 2018

By George G. Reed

Approximately 200 samples of iron ores and other iron- bearing materials have been tested for amenability to treatment by the R-N process in bench scale laboratory work. Twelve large lots, ranging in size from 900 net tons to 18,500 net tons, but generally 3,000 to 4,000 tons each, have been processed in the R-N demonstration plant. The ores tested in the demonstration plant ranged from 27 to 70 percent iron content and gave excellent results. (1) The demonstration plant has a nominal daily capacity of 50 tons of high quality iron briquettes and has now operated for over five years. A continuing program of process improvement is carried on between demonstration on potential licenses ores. An important development is the complete elimination of any secondary products which, in the past (2,3,4,5), resulted from treatment of certain low-grade ores.

Jan 1, 1960

By William H. Mount

INTRODUCTION The requirements of mine ventilation demand the constant attention of the mine operator. Just as the physical mine structure changes with time, the ventilation requirements of a particular mine change considerably from season to season and even from day to day. No ventilation system can remain adequate indefinitely; and all systems require monitoring and adjustments to achieve proper ventilation. Instead of being given fore- thought and planning, mine-ventilation systems too of- ten are erected hastily, merely to correct an already un- healthy situation. The usual result is an inefficient and costly system that, in some instances, may prove in- effective in providing fresh air to the point of need. The ventilation of mines is a combination of both art and science. The fluid that must be moved is in- visible; its properties change drastically with temperature, barometric pressure, and humidity; and the methods of measurement are not precise. In part, ventilation engineering must rely upon the art of good industrial ventilation experience and sometimes even the trial-and- error method. However, the properties of air can be determined with relatively inexpensive equipment; with some care, measurement accuracies within 5% of the actual values can be obtained. Thus the art of ventilation gradually is being supplanted by improved engineering practices. Although the direction of flow and the volume may not be predicted correctly by airflow equations in every situation, it is better to try to predict the behavior of a given ventilation before installation than to proceed blindly with a system design. When used with the discretion that comes from education and experience, the basic laws of ventilation can provide sub-stantial insight into the design of an air-handling system; and they can prevent wasteful or even dangerous designs from being installed. Since the mine operators who read this text will have varying amounts of exposure to ventilation theory, the basic laws of airflow and of mechanical ventilation are presented in the first section. The emphasis has been placed on the interpretation and use of fan characteristic curves that are supplied by fan manufacturers. Considerable information can be obtained from these fan curves, particularly when they are used with a graphic model of the mine, drift, or duct in which the fan or fans are to be installed. A few minutes spent comparing the various characteristic curves can help the designer obtain the correct fan for the job. However, the under- standing of a few fundamentals is necessary; and this text has been prepared to provide ample and understandable information in a "how-to" style. In subsequent sections of this text, more down-to- earth subjects will be covered, including the problems of air recirculation, relative merits of installing fans in series or in parallel, expected maintenance requirements (vibration, lubrication intervals, etc.), fan noise and some remedies, effect of an inlet bell on the fan per- formance, basic air-measurement techniques and equipment, and similar miscellaneous items. Although this text is not intended to be a comprehensive bible of mine ventilation, it has been prepared as a guide that provides some useful information to individuals responsible for the quality of the underground environment. Every person working underground is en- titled to the safest environment that can be provided within the limitations of existing technology and at a reasonable cost. Adequate ventilation is well within both limits, provided that the system is designed intelligently, in conjunction with the mining plan, and not as an after-

Jan 1, 1982

By G. J. Hodges

The Stillwater Mining Company, a partnership of Pittsburg & Midway Coal Mining Co. and Manville Corporation, operates a precious metals smelter at Columbus, Montana to further up-grade concentrates from its platinum/palladium mine. The smelter began operation in the summer of 1990. The gas cleaning system in the facility utilizes "oxidation/dilute mode" dual-alkali scrubbing technology to capture sulfur oxide gases from the process gas streams. This paper describes the rationale for selecting the dilute mode dual-alkali system and summarizes design parameters. Start-up problems and their solutions are also discussed.

Jan 1, 1992

By S. B. Patton

To fully utilize a ventilation simulator as a planning and production tool, the network database must keep pace with mining progress. By using AutoCAD's attribute-definition function, the branch data and node coordinates can be stored as part of the branch-diagram file, and updated with the drawing. Attributes are drawing entities that contain text which can be extracted in a standard spreadsheet format or as an ASCII text file. The data can be subsequently loaded into a ventilation simulator with plotting capabilities, such as VNETPC. This paper presents the methodology for using AutoCAD's attribute feature in a ventilation simulation.

Jan 1, 1994

By Gary L. Nelson

An overview is provided of Franklin Industrial Minerals mica mine and plant operations located near Velarde, New Mexico. Operated by Franklin Industrial Minerals since July of 1990, several process and product modifications have been developed and instituted to improve the operation. In addition to a brief history of site operations, descriptions of the mining, beneficiation, delamination grinding, and product classification processes are reviewed. Supportive topics discussed include equipment modifications and improvements, product application diversification, and specific product characterization. Also reviewed are the key areas of safety, environmental responsibility, and programs pertaining to process quality control and product quality assurance.

Jan 1, 1994

By D. Morin, J. Villeneuve, S. Foucher

The development of new processes has to follow "best practice" rules in order to be technically and economically as efficient as possible. However, innovations, new process routes and new rules are continuously emerging to minimize financial risk and maximize environmental compliance. Process simulation, which offers a complete overview of the flowsheet, makes it possible to cope with this new challenge-minimizing waste production and water consumption. Furthermore, simulation provides an estimate, at the early stage, of the cost of alternative technical routes. Four examples involving biotechnological circuits are presented, both at the design and commissioning stages.

Jan 1, 2000

By F. M. Doyle, J. P. Dwyer

Introduction The mining industry has a poor public image. It is often perceived as a despoiler of the landscape and a polluter of the environment, and there is little recognition of societal needs for the raw materials and fuels that this industry produces. There are many reasons for this poor image, but an important one is that a substantial number of mining operations have caused significant damage to the environment. Many of these operations, particularly those that now are abandoned, continue to have an adverse impact, principally in the form of water pollution.1 In some cases, the damage caused by this pollution extends well beyond the immediate region around the mine. Chemical contamination of ground and surface waters can, and does, occur in nature when these waters flow through or over undisturbed, mineralized rock masses. However, the problem is greatly exacerbated by mining because the mining activities increase, by several orders of magnitude, the permeability and the surface area of rock that can be contacted by percolating water. Water flowing through either the mine workings or the waste rock dumps becomes contaminated. Pollution can also arise if leachate from tailings ponds enters either groundwater or surface waters. This leachate may contain chemicals used in processing the ore. The magnitude of the threat posed by mining wastes depends on the type of minerals in the deposit, and on the chemicals used to process the ore. The magnitude of the threat also depends on two other, site-specific factors. One is the volume of water flowing into the mine and through the dumps, which depends on rainfall patterns, topography, and whether the mine workings are surface or underground. The other is the proximity of the pollution source to groundwater or surface waters, which depends on both the climate and geology. These factors influence the concentration and the quantity of polluted water forming and reaching the receiving water. Mining activities present a potential problem of enormous scale. Vast amounts of rock are mined each year2 and, as noted above, substantial problems have arisen at some mine sites. These problems are usually exceedingly costly to address, and it is imperative that these mistakes not be repeated. There are indications that we can accomplish this goal; we now better understand the processes that cause pollution and have methods to prevent or contain it. In addition, in the past few decades society has started to recognize the need for all industries to operate in a manner that maximizes the health and safety of workers and the public and minimizes adverse environmental impacts. A variety of recently enacted federal and state laws regulating public health and environmental hazards reflect the increasing concern over these issues. Many statutes, such as the federal Clean Air Act and the Clean Water Act, encompass activities undertaken by the mining industry. Other laws, such as the Surface Mining Control and Reclamation Act, have been written to regulate specific hazards posed by this industry. At the present time, the federal government. through the Environmental Protection Agency (EPA), and several state governments, are preparing new regulations specifically tailored to control the disposal of mining wastes. Given the magnitude of the potential environmental and health risks posed by disposal of mining wastes and the regulatory costs to the mining industry (both of which are due to the tremendous volume of waste generated), it is especially important that regulators have a good understanding of the different types of mining wastes and the risks they are likely to pose in various geographic and climatic circumstances. Only then can a regulatory program be designed with suitable procedures and substantive criteria to protect the environment and ensure compliance, while avoiding unnecessary or wasteful expenditures. California has long enjoyed a large, active mining industry. Today it produces a wide range of mineral commodities. The revenue from production of non-fuel minerals in California ($2.85 billion in 1988) greatly exceeds that of any other state. About a third of this revenue is from the production of inert sand, gravel and crushed stone. However, the remainder is from the production of a wide range of materials. These include boron minerals, rare earths, asbestos, talc and pyrophyllite, and gold. In earlier decades, an even broader range of minerals was produced, including mercury, copper, lead, zinc, and barite. There are acute environmental problems at some of these early mine sites. Because in 1987 the state of California was engaged in a revision of its regulations for mining waste disposal, the legislature commissioned a study by researchers at the University of California at Berkeley to investigate and review: the magnitude of the problem posed by these wastes, • the best feasible control measures available for waste management and disposal, • the problems of abatement and cleanup at so-called "problem" mine sites, • the current regulations imposed on mining waste disposal by various federal, state, and local agencies and the effectiveness of these regulations. This paper summarizes the principal findings from this study (Mining Waste Study, 1988). The lessons from this investigation are likely to be of general interest because of the diversity of mineral products produced, and the wide range of geographic and climatic conditions encountered. The acute problems seen at some of the older mines are typical of the western United States, and teach useful lessons on strategies that should be implemented at new mines to prevent recurrences of these problems.

Jan 1, 1992

By Glenn A. Hazen

Longwall mining is the preferred method for removing underground coal since a larger amount of coal can be removed faster and with less waste when compared to the room-and pillar type mining. Thus, the coal tonnage removed each year by longwall mining methods has increased dramatically. However, a high extraction rate results in surface subsidence which has adverse effects on the environment and on surface structures. Predictions of structural damage are dependent on the magnitude of the expected horizontal strains. Three methods for predicting subsidence characteristics are considered in this paper: the graphical method, the profile method, and the finite element method. All three methods can be used to predict ground movements and horizontal strains. However, the finite element method, which takes into account the structural properties of the stratigraphy and equilibrium of the overburden, is theoretically the more logical choice for use in subsidence prediction.

Jan 1, 1987

By J. H. Kempton

The scrutiny given to model predictions of pit-lake water quality has focused attention on the uncertainty associated with long-term predictions. Although comparison of probabilistic predictive modeling of water quality in existing pit lakes indicates that short-term predictions can bracket most parameters, uncertainties in wall-rock reactions and the stability of groundwater composition and climate remain unquantified. This overview of the uncertainties associated with longer-term predictions is presented as support for those considering policy decisions that must be made in the absence of reliable estimates of future conditions.

Jan 1, 1998

By T. C. Crosby

Grinding has a marked effect on concentrator recovery and opera- ting cost, improved operation through automatic control can enhance plant performance. The correct application of automatic control can only be accomplished after the basic process variables and their effect on mill operation have been defined. This paper develops a control system for a closed circuit grinding system. Typical control systems such as feed, water flow, level and circulating load are discussed. A method of determining controllability is outlined using the calculated reaction curve technique. Various successful methods of automatic grinding control applications are discussed and future possibilities are outlined. Although this paper primarily deals with closed circuit wet grinding circuits, the principles involved can be readily applied to other processes.

Jan 1, 1966

Gold cyanide equilibrium adsorption isotherms in the loading range typical of operating carbon-in-pulp/carbon-in-leach plants have been established and the effect of various cations and the presence of copper cyanide species quantified. It was found that the equilibrium loading of gold was enhanced by the presence of sodium or calcium, with calcium having an order of magnitude stronger effect. The presence of copper has an adverse effect on the equilibrium loading of gold. A unified model was developed to predict the effect of sodium and calcium concentrations in solution and the competitive carbon adsorption of copper on the equilibrium loading of gold on carbon. A satisfactory agreement between the measured gold equilibrium loadings and the model results was obtained over a wide range of solution conditions.

Jan 1, 2010

By Robert Stefanko

The importance of underground stress instrumentation cannot be minimized. It was Lord Kelvin who said that unless you can assign a number to a quantity,, you know very little about it. Most engineers will agree although this kind of statement is resented by our friends in non-technical fields. Mining is undergoing a revolution from art to science. But how can mining methods be optimized if there is no way of measuring the effectiveness of a given mining method? Do we know how effective a' support is unless we can determine its reaction to the mine structure? How do we assess the need for modifications to existing systems and supports, and how do we measure the effectiveness of such changes? Cut and try techniques are too wasteful of time and energy, and rarely provide solutions to a given problem. The purpose of underground stress instrumentation is to provide answers to some of the above questions -- answers that cannot be obtained otherwise This does not mean that laboratory studies are not valuable -on the contrary. Laboratory and underground studies supplement one another. Rock mechanics had its conception with the study of stresses in homogeneous, isotropic, and elastic models subjected to various force systems. These analyses were valuable inasmuch as they pinpointed possible sources of trouble due to stress concentrations. If the results observed underground did not always agree with the experimental analysis, it was not an indictment of the latter. More probably, the discrepancy could be attributed to the lack of similitude between model and prototype. The more nearly one can simulate underground conditions in a model, the more apt one is to produce results which correlate well-with underground observations. It is impossible to completely simulate underground conditions because all of the significant design parameters have not been recognized and evaluated. What better way can one evaluate these parameters than by underground stress instrumentation?

Jan 1, 1963

By R. Pazhianur

Many investigators conducted surface force measurements between hydrophobic surfaces in water, and observed attractive force that was substantially stronger than the van der Waals attractive force. The excess force was appropriately referred to as “hydrophobic force”, for which many different theories have been put forth by numerous investigators. In an earlier publication (Yoon and Ravishankar, 1996), it was suggested that the hydrophobic force maybe due to the interaction between the large dipoles created by the surfactants adsorbing on solid surfaces in patches (or domains). In the present work, a mathematical model has been developed to further elaborate the theory.

Jan 1, 2003

By E. Karampinos, P. Morissette

"INTRODUCTION Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting both appropriate systems and the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation. Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights on the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement over the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is not often available at mine sites. Even when the expertise is available it requires a major time and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support. Rock reinforcement is an integral part of all ground support systems used in underground mines. Long flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This paper focuses on the optimization of the cable bolting strategy in squeezing conditions at the LaRonde Mine by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 1, 2018

By J. E. Gebhardt, S. Chander

Significant advances have occurred in the use of electrochemical techniques for sulfide mineral flotation research. The techniques have been used singly or jointly with other characterization methods. When used in combination with other methods, the electrochemical methods provide a means to control the state of oxidation of the surface. Various analytical methods are employed for characterization. The methods that have been used include wetting, x-ray photoelectron and fourier transform infrared spectroscopies. The electrochemical methods include voltammetry and transient electrochemical techniques of galvanostatic polarization and AC impedance spectroscopy. The challenge for the future lies in the utilization of this knowledge in plant operations so as to increase the overall efficiency of flotation separations.

Jan 1, 1989

By R. L. Pariani, R. R. Moskalyk

Justifying refinery material handling equipment jointly involves economics and indirect benefits. The simple evaluation method is applicable when either retrofitting facilities or costing new metal refineries. The text includes points of interest regarding equipment selection as an additional guide. Although the copper industry was used as a basis, it is recognized that similarities in material handling may exist within the parallel electrolytic refining and winning of metals such as copper, nickel, lead, zinc, tin, and cobalt. The analysis of four major automatic systems, typically implemented in many tank houses, includes tabulated data plus a detailed description of additional benefits. General information regarding auxiliary material handling equipment and an overview are included for subject completeness. It is suggested that the quantitative and qualitative aspects presented may contribute to the basis for justification of automated material handling. The labor-oriented economics plus related intangible benefits described herein should provide incentives to modernize or replace manual operations where practical.

Jan 1, 1987

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of a massive pillar failure in a room-and-pillar mine. The mine employed a nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated out by quickly, and, within 24 hours, it had covered an area approximately 1,250-m- (4,100 ft-) long by 762-m- (2,500-ft-) wide. The failure was caught and stopped by a solid barrier pillar. Using computer modeling, this study indicates that the massive failure was initiated because of a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of the absence of barrier pillars between some panels and between mains and panels. Based on computer modeling, alternative mine plans were proposed to avoid such problems.

Jan 1, 2002