Search Documents

By Gene E. McClelland, Dirk J. A. van Zyl

5.1 INTRODUCTION Heap leach cyanidation techniques possess considerable potential for exploitation of low-grade ores, small ore bodies, mine strip waste and tailing materials where fine grinding is not necessary for good extraction. For heap leaching to be successfu1, ore must exhibit certain characteristics, as previously discussed in Chapter 1. Primary among the necessary ore characteristics is that the ore must have good permeability after being crushed or treated and stacked into heaps if uniform distribution of the cyanide leach solution is to be achieved. Gold and silver ores containing excessive amounts of clays or fines generated by crushing are some of the most difficult to treat successfully by heap leaching. The presence of excessive amounts of slimes (generally classified as minus 50-micron or 270 Tyler mesh sieve size particles) in the heap leach feed will slow the percolation flow of the leach solution, cause channeling, or produce dormant or unleached areas within the heap. This may result in unreasonably long leaching periods and poor extractions. In extreme cases, the clays or slimes can completely seal the ore heap, causing the leach solution to run off the sides of the heap rather than to penetrate the ore heap. The problem of heap leaching ores containing fines can be aggravated during stacking and preparation of the ore heaps, because natural sorting of coarse and fine material occurs during these steps (Johanson, 1978). This phenomenon results in a concentration of ore fines at the center of individual ore piles and a concomitant concentration of larger rock fragments on the lower slopes and base of the piles. When the individual piles within the heap are leveled off prior to installation of the sprinkling system which delivers the leach solution, additional segregation occurs as the fines sift through the coarser ore particles. The segregation results in localized areas or zones with marked differences in permeability. As a consequence, the leach solutions follow the path of least resistance, percolating downward through the coarse ore regions and bypassing or barely wetting areas that contain large amounts of fines or slimes. Effective utilization of marginal gold and silver resources through heap leach processing requires the development of new methods in order to achieve more uniform size distribution during ore heap preparation and better slime control during leaching.

Jan 1, 1988

By F. H. Deily

The petroleum industry has developed and utilized many aspects of rock mechanics, both in its search for petroleum and in its drilling and production operations. Geological exploration activities have been improved by knowledge of earth tectonic forces. Better understanding of seismic wave motion has contributed to a more accurate interpretation of geophysical data. Drilling activities have benefited from basic knowledge of rock strength behavior under in situ conditions. Production has been significantly increased through stimulation techniques, such as hydraulic fracturing. The ability of rock mechanics work to contribute to future petroleum activities will depend upon the development of knowledge of rock properties under greater depths and at higher pressures and temperatures.

Jan 1, 1969

By R. Bleischwitz, R. Delzeit

"Tantalum, a heavy metal with characteristics such as superconductivity and high terminal resistance, nowadays is the most efficient material for production of capacitors, which are essential for production of small electronic applications like notebooks and cell-phones. It is one of the strategic resources for information societies. With supply extracted from Central Africa (Congo / DRC), China, Australia, and Canada, it can serve as an example for sustainability efforts in the management of non-renewable resources in Developing Countries, Newly Industrializing Countries and Industrialized Countries alike. The paper analyzes the life cycle of tantalum in its environmental, social, and economic dimensions. The first section highlights the importance of tantalum, showing a demand-driven market. The second section analyzes current and future supply. The third section tackles environmental and social impacts of tantalum mining in different legislations. The fourth section especially deals with the Case of the Democratic Republic of Congo since companies have been accused of participating in a civil ‘resource war’. Section five will draw conclusions for sustainable resource management. Written in an interdisciplinary manner, the article has a bearing on economics, especially on resource economics and new institutional economics, as well as on geography. It deals with questions such as security implications of physical scarcity in rapidly growing markets. In doing so it can, firstly, be shown that information exchange in combination with reputational risks lead to a shift in extraction activities from a Developing Country (DRC) to an Industrialized Country (Australia); i.e. a ‘race to the bottom’ does not take place. This, however, does not mean that market mechanisms work properly since information exchange (especially with China) is incomplete, moral hazard still prevails, and inadequate institutions hamper development processes in an exporting country like Congo. Any sustainable resource management for tantalum not only should foster gathering and exchanging better information on environmental and social impacts, but also incentives for upstream metal recycling in industry as well as support for governance processes in Developing Countries"

Jan 1, 2005

By Salvatore] [Parand

Deep well disposal is a much used and abused term which is the panacea for wastewater disposal in some minds and creates near hysteria in others. It can be the answer to a difficult waste disposal problem, or if improperly employed, can create more problems than it solves. My purpose in this presentation is to focus on the value and limitations of deep well disposal as expressed by New York State's experience and policies. To he sure, I feel a place for such practices docs exist if adequate safeguards are utilized. I shall give a broad brush approach to New York's legislative, geologic and operational concerns and speak briefly on some case histories. I shall not delve deeply into the technological details since I am not an expert in mining exploration or well drilling.

Jan 1, 1973

Mineral processing plant operators are faced with the necessity to choose between many different possibilities for plant improvement. Only a few such possibilities, however, can be tested on the industrial site. Steady-state simulators make it possible to assess the effects of several different flowsheet modifications in a few days, thus helping the process engineer to make his choice implement the solution that seems the most appropriate and check it. The example described here is the crushing and grinding circuit of the Shila Gold Mine, jointly owned by CEDIMIN SA and BUENAVENTURA SA, in Peru. Several possible modifications for the purpose of increasing capacity have been simulated and the results assessed in terms of technical quality, investment costs and energy consumption. The best solution indicated by the USIM PAC simulator was implemented and gave a 20% increase in capacity with a pay-back time of two months.

Jan 1, 1993

By Geoffrey Purcell

The flotation response to amine collector of quartz and the feldspars microcline and albite, of the pyroxenes augite and spodumene, and of olivine can be, explained by a physical adsorption model. Flotation decreases in the order given above, and the different behavior of the three groups is attributed to structural variations of the silicates, With sulfonate collector both chemical action and physical adsorption play their part in producing hydrophobic surfaces, and flotation increases in the order given.

Jan 1, 1966

By W. F. McDermott

The Iron Ore Industry has perhaps seen more varied and drastic changes in its approach to crushing and grinding in the last 5 years than any of the other mineral industries, Multimillion ton per year plants have become common place. Centralized control and computers have become an established benefit. Autogenous grinding along with a variety of rod and ball grinding flowsheets are in use. This morning I will discuss a few of the more important and new concepts in the control of these crushing and grinding circuits.

Jan 1, 1970

By C. W. Matthews

Introduction Screening is defined as a mechanical process which separates particles on the basis of their size and their acceptance or rejection by a screening surface. The key element in this method of particle sizing is obviously the screening surface, the medium that contains the apertures for the passage of the undersize material. This surface must be strong enough to support the weight of the material being screened, flexible enough to yield to the vibrating force applied to it, yet light enough to provide a reasonable ratio of open area to attain a practical through- put. To balance all of these factors is difficult enough. The problem is compounded, however, because screening media are made in a great variety of types, shapes, sizes, and materials of

Jan 1, 1985

By S. C. Westerfeld

The original patent for the gyratory crusher was granted to Philetus W. Gates in 1881. This first crusher was used by the Buffalo Cement Co. At the time these early gyratory crushers were developed all mining and quarrying, either underground or open pit, was done by hand; tonnages generally were small and product specifications simple and liberal. Likewise plants were small and demands for small product sizes practically nonexistent. In addition to substantial amounts of hand labor, the available material handling equipment was small, simple, and not suited to handling large run of mine ore. Mine can, cable ways, or belt conveyon transporting crushed material to the mill had limited capacity per hour. At the turn of the century the largest Gates crusher, the No. 9, had a receiving opening of 21 x 48 in. with a three-arm spider and a 21 x 80-in. opening with a two-arm spider. The steam shovel began to change the entire picture of open pit quarrying. As a result of the use of steam shovels around 1910 crushers with 48-in. receiving openings were built; thus it can be seen that the basic gyratory crusher was developed prior to World War I. The improvement of the internal combustion engine and the use of pneumatic tires created a new set of operating conditions. Early mines were small, using shrinkage stoping and small mine can. The capacity of material handling was small, limiting the size of the largest piece and the feed rate. Improved material handling resulted in more and more large open pit mines with large shovels and a tremendous increase in the size of off road or mine haul trucks or rail can. Primary gyratory crushers also increased with receiving openings as large as 60 in. and connected hp of 1,000.

Jan 1, 1985

By Igor Gonzales G.

Southern Peru Copper Corporation (SPCC) has recently completed the construction of copper leaching, solvent extraction, and electrowinning facilities at their Toquepala and Cuajone plants in Southern Peru. Much of the ore for these new operations is the result of the existing mining operations that have been in existence as early as 1959. At Toquepala, pre-conditioning and bacterial dump leaching of the sulfide ore that was too low in copper content to be processed through the copper concentrator began in 1987. The Cuajone heap leach operation is treating copper oxide ore that has been stockpiled since the Cuajone concentrator began operation in 1976. The pregnant leach solutions from the dump leaching at Toquepala and the permanent pad heap at Cuajone are combined into one plant feed solution. Adjacent to the large dumps at Toquepala, a solvent extraction and electrowinning facility has been constructed. The electrowinning facility has a planned annual production rate of35,000 metric tons per year Grade A cathode copper. Initial production of the cathode copper began in November 1995.

Jan 1, 1996

By Allan H. Caverson

Over the past nine years a means for measuring the distance between the mine roof and floor has been developed at the White Pine Mine which yields relevant information utilized in the mining operation. The technique known as "convergence!' is an efficient, low cost way for obtaining large quantities of data for predicting roof falls, caving activity, and overall mine stability. From a limited introduction in 1964 related to monitoring an experimental longwall project, the activity of convergence measurements has been expanded to become a production tool now found in all sections of the mine. Presently, the program involves four main types of activity: 1. Monthly measurements in areas known to be active, and in sample blocks scattered throughout the mine for a long-term stability study. 2. Semi-monthly measurements along vital travel roads, belt drifts and compressor sites. 3. Weekly measurements in areas where men are working. 4. Daily measurements in pillar-recovery and caving operations. Today, one field engineer and six technicians are involved full time in convergence work. Rock Mechanics technicians have installed approximately five thousand stations since the start of the program and of this number, over twenty-five hundred active stations still comprise the mine-wide network spread over the more than five square mile extent of the White Pine Mine workings.

Jan 1, 1973

By D. H. H. Quon, A. Ahamd, G. Pouskouleli, T. A. Wheat

An outline of the contributions of hydro- metallurgical techniques such as sol-gel processing, direct precipitation and hydro- thermal decamposition for the development of high-quality ceramics is given and examples drawn from recent work on both structural (engineering) and functional (electrical) ceramics are discussed.

Jan 1, 1990

By Randhir S. Sehgal

After some decades of lying low and being treated as a second rate fuel, coal is back in the news. Production is rising. Predictions are for an ever expanding use, and they differ only in their rates of increase. Even the FBI is involved in trying to stop fraudulent sales of non-existent coal lands and leases to the innocent. In short, we have a nearly chaotic boom on our hands. Obviously our energy production base is in the process of undergoing a major shift, and the process will present many problems. However, there is little doubt that the industry has the basic strength and organization to be able to deal with the new issues that will arise as a result of these shifts in production and use of coal. After all, it does produce nearly 800 M tpy now, and coal is the single biggest fuel for generation of electricity. This role of coal is illustrated in the table below, which shows the coal equivalent quantities of various fuels used in the production of electricity.

Jan 1, 1980

By Raymond T. Moore

The Federal Coal Mine Health and Safety Act of 1969 (FCMHSA) begins with this statement: "Congress declares that the first priority and concern of all in the coal mining industry must be the health and safety of its most precious resource -- the miner; . . ." At the Federal level this responsibility is shared by the Department of the Interior and the Department of HEW. The health research and standard setting activities under the Act are largely the responsibility of the Department of HEW, and with the exception of Title 4, Black Lung Benefits, have been delegated to our Institute, which I will refer to henceforth as NIOSH. In addition, we bear certain joint responsibilities with the Department of the Interior. These include dust sampling and respirator approval. To complete the picture, the Department of Labor has recently assumed Black Lung Benefit respon¬sibilities from the Social Security Administration under Title 4 of the Act.

Jan 1, 1974

By J. A. Brierley, C. L. Brierley, K. A. Prisbrey, R. W. Bartlett, J. G. Harrington

Bacterial oxidation of gold-encapsulating sulfide minerals in low-grade refractory ores was investigated over a period of one year. Crushed ore samples were held in wet, bacteria-inoculated, aerated columns. Sulfide mineral oxidation data were correlated with subsequent gold cyanide extractabilities. Experimental results for both sulfide conversion and gold extraction were compared with a biooxidation kinetics model that incorporates rock size, mineral grain size, and heterogeneous pyrite reaction kinetics. Using the model, extrapolations were made over three years for biooxidation of ore in large stockpiles. Ferric ion (oxidant) diffusion in the solution-filled pores of the rock matrix does not control the biooxidation kinetics of ore crushed to -25 mm.

Jan 1, 1993

By Lawrence Adler

[An innovative framework is proposed which most efficiently and systematically handles the large quantity of information needed for equipment failure and other non-performance analyses. It is based on the accepted engineering dimensions of mass (material), length (geometry), and time (MLT). To these are added human and machine factor. Several failure "Modes" are identified for each dimension, which are then subdivided into specific "Types". Material Failure Modes such as Separation and Slip are easily recognized, but others had to be established. Geometric Failure Modes are usually straight-forward, Obvious ones include Geometrics Design and Stability with more synthesized. Time Failure Modes are again largely self-evident such as Life and Chemical Effects, others are needed. Human and Machine Factors as failure modes are loosely assembled. The results contain strengths, but also organizational weaknesses which are noted. Lacking a better alternative its use is recommended.]

Jan 1, 1989

By Charles Bruce

Three years ago, at a reception given during the Steel Institute meeting in New York, I heard the remark, "A new formula must be found for foreign investment." This was immediately following the takeover of U. S. Steel's Matilde operation in Bolivia. Recently, at the World Mining Congress in Lima, Peru, the subject of foreign investment was still a lively topic of conversation. The nationalization of the copper mines in Chile and recent trends in the "Third World" have made all but a few extremely wary of investment anywhere other than in the ?stable? countries. Now, the fallibility of this philosophy has been demonstrated in such "stable" countries as Canada, Australia, and Ireland. Yet, nationalization is not new to us. The events in Chile were classified as disastrous to the affected companies, but so were the effects of nationalization to the majors in Bolivia in 1952. Mexicanization of the mining industry in Mexico was considered impractical by many. Now, those who accepted it are finding it to be workable.

Jan 1, 1975

By Duk-Won Park

Ground water has been a problem in underground mines (Anon., 1981; Aughenbough, 1973; Stansbury, 1981). Water migrates from water-bearing formations and surface water bodies such as lakes, ponds or creeks into the underground workings through fractures and cracks. As a result, under- ground workings become plagued with the necessity of having the water pumped out in large quantities. Underground workings become flooded when unexpected amounts of water flow into the openings, especially when mines use pillar extraction or longwall mining methods. It is difficult to detect water bodies above the coal mine roof before water problems take place. The resistivity method was used as a method for detecting water saturated rock layers and bodies of water above the roof of a coal mine in northern West Virginia, where the multiple seam mining method was being used.

Jan 1, 1983

By T. W. Flemal

Good afternoon gentlemen. To begin, may I say ?thank you? to the AIME for the invitation to be here today to talk about my company's experience with shovel, truck, pocket, to car loading. The other author of this paper is here today. (Introduce John Sweet). Before we get to the details of this paper I want to tell you a little about Erie Mining Company. Erie Mining Company is located on the east end of the Mesabi Range in northern Minnesota and is engaged in the business of processing taconite rock into iron ore pellets. In 1970, the twelfth year of production, Erie will produce its rated capacity of 10.3 million tons of high grade iron ore pellets. The plant is the first of five iron ore pelletizing operations managed by Pickands Mather & Co. with a combined annual production capacity of 21 million tons. This plant began producing high grade iron ore pellets in 1957 placing it among the earliest of taconite production facilities in North America. Historically Pickands Mather & Co. had been a leading natural ore mine managing firm in the Great Lakes region for more than 70 years. Pickands Mather & Co. moved into the new field of taconite mining and processing with management and operational experience from the open pits and underground mines. We were to learn much of volume taconite handling requiring new equipment and new procedures. A trial and error period through the early years of taconite processing developed through the operation of an experimental sized preliminary plant near the present Erie Mining Company site.

Jan 1, 1970

By Ande&apos, Bengt n

The first Model 480 SALA-HGMS R carousel high gradient magnetic separator was recently manufactured (Figure 1). The carousel's design was based upon the high gradient magnetic separation technology developed and owned by Sala Magnetics Incorporated, Cambridge, Massachusetts. After a short (approximately 300 hours) in-house mechanical and electrical test and break-in period, the carousel was ready for a long term demonstration test. This paper describes the demonstration plant and operational performance of the Model 480 HGMS treating a low grade iron ore tailings. A location convenient to Sala International's main office in Sala, Sweden was desirable because Sala engineers and technicians were to operate the demonstration plant. The Strassa iron ore mine in central Sweden was chosen because it fit most of the criteria that was important for a good demonstration site. The Strassa mine is part of the state owned Svenskt Stal AB. The mine produces about 320,000 tons of iron concentrate per year consisting of 200,000 tons of magnitite concentrate and 120,000 tons of hematite concentrate.

Jan 1, 1980