Search Documents

By I. L. Jennings

In most industrialized countries, the largest element of the mining industry in physical volume is that devoted to the extraction and processing of materials for use as construction aggregates. Required for all developments in industry and commerce, power and transportation, and housing and public services, their use is so widespread that possible sources are exploited throughout all geographic regions, as close as possible to the point of use. Thus, it is also the most frequently encountered form of mining throughout the world. These materials come from four main sources:- (a) Excavation of unconsolidated deposits of sand and gravel (b) Stone quarrying. (c) Processing of slags and other mineral wastes. (d) Manufacturing from clays and shales by heat fusion. The major uses are in: (a) Portland cement concrete, that most versatile of construction materials, including the many concrete products in current use. (b) Asphalt cement concrete; widely employed for paving roads, parking lots, airfields, etc. (c) Foundation materials, such as road base, granular backfills, railway ballast, etc.

Jan 1, 1968

By V. A. Scovazzo

The analytical pillar design procedure employing the Wilson equation is based on the site-specific material strength of the floor, pillar, and roof rock. Stable pillars so designed will sometimes be larger than those designed using empirical methods thus providing more stability or at other times smaller than empirically designed pillars thus conserving natural resources. Presented here is a detailed procedure for the analytical design of soft rock pillars using the Wilson Equation. An example of this procedure is presented that uses data from a mine in the Owl Seam in Southern Appalachia. These Owl Seam pillars are now in use and are performing as expected. Also addressed is an assessment of the Dr. Scovazzo?s analytically designed pillars based on pillar performance data gathered by Dr. Mark in the Southern Appalachian Coal Field.

Jan 1, 2010

By P. Aparicio

The rheological properties of five kaolins, isostatically pressurized at 4 x10 Pa for 10 min in the presence/absence of water, was determined. Under dry conditions, measured viscosity values either decreased or remained the same. After treatment under wet conditions, measured viscosity values were 30-60% higher at high shear and 50-60% higher at low shear. These results correlate with variations in nanomorphology and structural order. Dry compaction degraded kaolinite crystals but wet-pressing appeared to cause an increase in the proportion of euhedral crystallites and a decrease in deformed crystals. Dry compaction decreased the low-defect phase proportion (ldp), but in contrast, the ldp in wet-treated kaolins remained constant or increased. Results show that hydrous pressure treatment produces a change in viscosity of kaolin suspensions, yielding the potential for improving paper coating performance, whereas anhydrous pressure treatment decreased or maintained the viscosity.

Jan 1, 2010

By Jun Han

Coal has been mined in the Kailuan mining area for more than 130 years. The remaining reserves consist of, in large part, coals that would have been considered economically unminable or technically not feasible by the previous generations. Some of the current operations have to resort to overmining because the lower seams had been extracted in the past. This paper deals with the feasibility and proper layout of mining roadways of overmining carried out in the No. 5 seam of Qianjiaying coal mine of Kailuan mining area using numerical and physical simulation. FLAC2D was used to investigate the characteristics of stress and displacement in the overburden after extraction of the lower seams. It also analyzed the proper layouts of gateroads in the upper seams, i.e. locating them in the stress-relief zone of the gob so that their stability can be easily maintained. In addition, a two-dimensional physical model was constructed for investigation of damages to the upper seams due to mining of the lower seams. Finally, based on the results of investigations, proper gateroads layout was designed and successful extraction was implemented for panel 1357 in the No.5 seam.

Jan 1, 2009

By J. D. Forrester

I have availed myself of the opportunity to prepare, and to give this talk because, as incumbent Chairman, I am directed by the Bylaws of the Council of Education to make an Annual Report of the Council activities which have transpired during the past year. In addition, and inasmuch as I have this captive audience, I am taking the liberty to express also some beliefs I hold about various other elements of Mineral Industry education. First, my report is that constructive progress has been achieved in the Council of Education during 1960-61. These advancements have been particularly notable through projects carried on by the Committee on Meetings and Programs, by the Student Chapters Committee, by the Accrediting Affairs Committee and by the Committee for Securing Better Representation of Mineral Industry Colleges. I believe each of these groups will report concerning details of their respective programs at the Business Meeting of the Council. On the other hand, not as much has been done in some areas of work as I had hoped would be the case when I took office as Chairman last February. Let me make clear that these delinquencies, for the most part, have resulted through my ineptness in handling of affairs; they are not caused by the failure to perform various assignments which I have given to council members.

Jan 1, 1961

By S. A. Bortz

IIT Research Institute has initiated several multi-sponsored research programs. In this paper the methods for developing four of these programs are discussed. In general, a broad area of investigation must be proposed to interest a spectrum of different industries. The work must not touch upon proprietary data and will probably involve a number of scientific disciplines. Thus, the problem to be solved will attract sponsors who need to know more about the area under study but do not wish, as a single company, to commit the resources required to obtain the necessary know-how for their needs. The paper draws on the background of four IITRI multi-sponsored projects: Size Reduction, a study of grinding of material to reduce their particle size; Melt-Formed Ceramics Research, a method of producing dense, polycrystalline ceramics using glass forming methods; Binders in Ceramic Processing, which addresses the problems associated with the use of organic aids for ceramic processing; and a Study in Air Pollution Technology, a program to review and assess pollution control equipment for current and future applications.

Jan 1, 1984

By N. L. Parduhn

Populations of Bacillus cereus spores are elevated in soils over four subsurface gold deposits in the western United States. Large deposit-to-background ratios of B. cereus populations were obtained in soil traverses over the Minnesota vein deposit, Empire District, Colorado (maximum 50:1); the Shasta (maximum 3,500:1), and Evening Star maximum 18,000:1) vein deposits, Shasta County, California; and the Hog Ranch disseminated gold deposit (maximum 40,000:1) in Washoe County, Nevada. Small increases in the concentration of toxic metals in the soil may be responsible for the elevated spore populations. The observed elevation of B. cereus spore populations near these gold deposits indicates that the method should be further investigated as a potential exploration tool.

Jan 1, 2013

By Yuting Xue, Todd Minoski, Daniel Su, Mark Van Dyke, Mark Mazzella, Steve Hicks, Zoheir Khademian, Nicole Evanek

Design of chain pillars in a longwall mine setting is one of the main engineering controls on the global and local stability of the mine. Challenges with roof instabilities, floor heaves, and pillar failures can be alleviated, to some extent, by careful design of gateroad configurations and chain pillars. This work investigates three different alternative designs in a three-entry-system gateroad configuration with an inter-panel barrier in a longwall mine in Virginia. Starting with the current design, which has faced challenges such as excessive floor heave, a geomechanical model developed in 3DEC software is validated by monitoring in-situ pillar stress in the yield, abutment, and barrier pillars in the mine. Next, three different chain pillar designs are evaluated in the model with a focus on roof sagging, floor heave, and pillar average stress. Results show the relationships among the alternative designs and instabilities associated with roof, pillar, and floor in the study mine, providing insights for optimizing longwall mining designs in deep-cover settings.

Feb 1, 2025

By Walter P. Hansen

Belt conveyors offer a reliable means and often do the most economical job for providing continuous bulk material transport, whenever the terrain permits their installation. The ore processing, construction and mining industries use belt conveyors to carry all types of material, from small to large tonnages. Most of the conveyors Fluor Mining & Metals, Inc. designs for metallurgical plants are in the in-plant category, of limited length and medium tonnages, and use fabric carcass conveyor belting. Belt widths can range from 24 to 60 inches Generally, the layout and design of these belt conveyors present no unusual problems. However, calculations for belt tension and horsepower, design of materials transfers, and the sizings and layouts of belt pulley stations and their drives are time consuming.

Jan 1, 1979

By Dean E. Albon

In the late 1940's and early 50's in southern Illinois, the usual open pit blasting in the coal field consisted of one or two rows of churn drilled vertical holes being shot with instant electric blasting caps. The entire shot detonated at one rime. In southern Indiana and Ohio most mines were drilling horizontal holes and they too were primed with instant EB caps. During the ten years from 1355 through 1965 many changes occurred in drilling and blasting methods. The churn drill in southern Illinois and the horizontal drill in Indiana and Ohio were replaced by the rotary vertical drill. The ammonia dynamites and liquid oxygen explosives were replaced by ANFO. The elctric blasting cap in the hole was replaced by a detonating cord down line and detonating cord trunk lines made the connections between holes and rows of holes. Host open pit mining was in areas far enough from town that the noise and vibration from blasting was, if not ignored, at least tolerated. During the 1960's open pit mining expanded to account for nearly 50% of the coal produced. Mines came closer to town and towns expanded along the highways with suburban homes and mobile homes. The mines began receiving complaints about the noise and vibrations from blasting operations.

Jan 1, 1976

By T. M. Yegulalp

A numerical model is being developed to assess the enhancement of permeability by improved fracture connectivity by micro-hydrofracturing. A generic two-dimensional percolation model has been developed to test the impact of various field conditions on permeability. Field data from Cyprus Minerals' Mineral Park Mine has been used to establish statistical properties of the observed fracture systems. Results of statistical anlyses of the field data and examples of the use of percolation model are presented.

Jan 1, 1995

By James W. Collins

The bucketwheel stacker/reclaimer is suited for a variety of bulk material handling systems, especially those operating with stockpiles in excess of 30,000 tons. The bucketwheel stacker/reclaimer, although relatively new in the United States (first introduced here in 1964), has been successfully used in European countries since the early 1940's. Basically the machine is the outgrowth of the bucketwheel earth excavator and the traveling tripper boom type stacker. Since their introduction here they have achieved wide acceptance, especially with coal fired power plants. (Figures 1, 2, and 3.) The stacker reclaimer has been utilized in barge and ship loading/unloading facilities, and in the material handling systems for steel mills, where it has been used to stack and reclaim iron ore at rates up to 6000 tph stacking and 4000 tph reclaiming. They have also been employed at mine mouth power plants for the handling and storing of the plant fuel supply and to help balance the mining rate with the fuel consumption rate.

Jan 1, 1973

By David R. Maneval

In 1956 the Legislature of the Commonwealth of Pennsylvania created a "Coal Research Board" in the Department of Mines and Mineral Industries. Over the years through amendments to the original legislation, the scope of authority for research has been expanded from the narrow area of improving and increasing the utilization of coal to covering all aspects of coal technology and any other area of interest which would be of value to the coal industry. In January of 1964, the Board commenced a vigorous program using appropriated funds and funds donated by the coal industry to finance a research program devoted to seeking solutions to the mine drainage problem. A review of published literature on the treatment of mine drainage indicated that much work done up to that point in time concerned only the mechanism of mine drainage formation and theoretical chemistry. Very few applied, developmental, or engineering studies had been devoted to finding practical solutions to the problem of polluted waters being discharged from active or abandoned mines. Projects were therefore undertaken on a wide variety of more utilitarian approaches. This paper will discuss briefly some of the pollution abatement approaches which have been funded by the Coal Research Board of this State, and will describe in some detail a multistage flash evaporator treatment plant now under construction.

Jan 1, 1970

By Reed S. C. Rogers

The most widely used machines for grinding coal to the sizes prescribed for the pulverized coal firing of furnaces, boilers, and kilns are the vertical ball-race, roller-race and roller-bowl types of mills. However, the increased use of coal has led to an increased use of tumbling ball mills for coal grinding. Specifically, air-swept ball mills are now a part of many dry pulverized coal firing systems, offering the advantages over vertical mills of lower maintenance costs and the ability to handle strong or abrasive (high ash) coals. The current use of wet ball mills is to prepare coal-water slurries for direct combustion, although in time they may also find routine application for preparing slurry feed for coal gasifiers. In either application, wet ball mills ofer the advantages that coal grinding and wetting can be accomplished in a single step, and that the mills are readily used with fine wet screens to assure top size control in the slurry product. The simulation of tumbling ball mills with mathematical models has reached a fairly advanced stage, but the concepts have been applied only recently to coal grinding. As this paper will demonstrate, however, significant progress has been made in the use of models in ball mill circuit design for coal grinding. Included is a description of the techniques used for simulation, recommended parameter estimation methods, and demonstrations of process engineering calculations for large scale coal grinding circuits.

Jan 1, 1986

By Neal P. Cochran

The United States is faced with increasing demands for electricity, coupled with continuing demands for crude oil and gas. Superimposed on these' national requirements are our national requirements for clean air and elimination of thermal pollution of our rivers. From the coal viewpoint, this situation is complicated still more by the rapid advances in nuclear power. In this paper, I hope to show a way to use our Western coals as a solution to this involved national problem by producing: 1. High quality crude 2. Low cost power 3. Economic byproducts We could expect these products to be made at one site in an integrated plant that would mine (extract) coal, process it, and convert it to electricity. Perhaps the most important attribute of the plant is its reduced water requirement and the elimination of air pollution from the power cycle. Quite logically, such a plant would probably recover valuable byproducts, such as pipeline gas, sulphur, cement, aluminum, and the like. Although the plant projected in this paper is a conceptual one, it is based on work now underway by Government and industry. Prediction of the future is a most hazardous occupation, but plants such as the one projected are based on current knowledge and can be expected to reach commercial operation in the near term future.

Jan 1, 1967

By L. A. Readdy

Defining classes of ore using geostatistical methods that match historical classifications has presented problems in the past. A simplistic and practical approach to this problem is presented. An example of the approach is presented using a porphyry type system as a case study. The technique described uses area of drill hole influence and known conditions from similar deposits, or the production history of the deposit being studied. It provides a practical bridging mechanism for defining the class of ore on a block-by-block basis using .the error of estimation value developed during kreiging. The approach provides a filtering method that refocuses attention on the adequacy of drill hole spacing.

Jan 1, 1985

By D. M. Thayer

In the last decade public awareness of the need for pollution abatement has increased greatly. The concern that had been previously shared by local and state conservation groups has spread to create a national concern for preservation of our non-polluted environmental assets and regeneration of those that have been wasted. Because other current matters such as inflation, civil rights,' tax reform and the Vietnam situation have been the object of most national concern, an extremely strong national pressure base has not been brought to bear on the pollution control crisis. Yes, the word is crisis, for in many areas pollution is of critical concern. One has only to look at Lake Erie, the skies about our major urban areas and many of our major rivers and streams to see this crisis These are not situations that can be corrected overnight. We are faced with two basic problems that should be attacked simultaneously: (1) Cleaning up the present sources of pollution and (2) preventing the generation of new pollution sources. What approach should be taken? As in any engineering problem, the limits must be well defined before a final solution is attempted. Pollution must be defined on a national basis. This means that basic Federal legislation and control is necessary. This should reduce any competitive advantage that can presently be gained by movement of operations from one state or geographical area to another on the basis of differences in local legislation .and enforcement. By giving real numbers as guidelines, selective enforcement can be avoided. As a starting point, for a definition of pollution let us use the following - "Any change in the environment occurring from other than natural causes." This definition may not be satisfactory to all but surely we must be somewhat dramatic in our statements to counteract the present prevailing philosophy. Our statement of this philosophy - "At what level of pollution can we afford to operate?" On the basis of our general definition we would like to state what we feel should be the philosophical statement - "How little can we change our physical environment as a result of operations?"

Jan 1, 1970

By D. L. Romero

The Line Creek Mine is operated by Crows Nest Resources Limited, a wholly owned subsidiary of Shell Canada Resources Limited. It is located approximately 25 km north of Sparwood in southeast British Columbia (refer to figure 1). The Line Creek coal deposit is part of the Upper Elk Coalfield in the East Kootenays. The coal is a medium volatile, low sulfur, bituminous coal and is used as a coking coal. Coal close to the outcrop is typically of low F.S.I. and is processed for thermal use. The present pits have a total coal reserve of 30 million clean tonnes and is a multi-bench, open-pit operation. The coal is recovered by front shovel and backhoe combination, and hauled to the plant with a fleet of 120-tonne and 40-tonne capacity trucks. Line Creek is unique in that it can simultaneously treat both metallurgical and thermal coal in separate processing facilities (refer to figure 2). Run-of-mine coal is delivered to the truck dump. The plus 50 mm material is scalped off and reduced to minus 50 mm in two rotary breakers. The raw coal is then conveyed to one of five, 5000-tonne capacity, silos. Typically one silo is used for thermal coal and four for metallurgical coal (refer to figure 3).

Jan 1, 1991

By Harry M. Conger

Kaiser Steel Corporation's Eagle Mountain Mine is located in the Colorado Desert, 60 miles east of Indio, California. Concentrates from the mine are shipped by rail 164 miles to the company's steel mill at Fontana, and also to Longbeach, California for export. Temperatures are typical of the lower desert ranging from a high of 120 degrees in the summer to a low of 25 degrees in the winter. The average annual rainfall of about two inches comes mainly as cloud bursts during the summer months. From its inception, the Eagle Mountain Mine has had the problem of breaking its mine rock. Practices followed from 1949 until 1962 were very costly, did not produce uniformly good fragmentation, and were incapable of sustaining high production. During this period, every conventional type of explosive then in use was tried and found to be unsatisfactory for one reason or another. The first slurry test work at Eagle Mountain was started in 195E and finally by 1962, after having tried all the slurry mixtures then available including some "home made" formulas, a metallized slurry was perfected at the mine which overcame all of the disadvantages of former blasting methods.

Jan 1, 1965

By R. A. Lowe

Smectite is a common impurity in the kaolins of Georgia. This impurity is harmful to the low-shear rheology of kaolin slurries in concentrations as low as a few weight percent. The deleterious effect of smectite on the low-shear rheology is due to the swelling of the mineral. Montmorillonite containing clays were treated to precipitate a compact brucite layer {Mg(OH)2} in the interlayer region of the expandable layer silicate mineral. This treatment forms a hydroxy-Mg-montmorillonite with characteristics similar to chlorite. This treatment effectively reduces the swelling capacity of the mineral and improves the rheological properties of kaolin slurries contaminated with smectite impurities.

Jan 1, 1999