Search Documents

By R. Y. Wan

Recent research efforts have shown have shown selective solvation extraction of a gold cyanide ion-pair complex from alkaline cyanide solution is possible with organic phosphorus esters. These alkyl phosphorus esters such as tributyl phosphate (TBP) and di-n-butyl n-butyl phosphonate (DBBP) can selectively load gold to rather high levels, even in excess of 30 gpl. However, traditional stripping techniques are not particularly effective. In this regard, gold recovery by direct electrolysis of the organic phase has been found to be an interesting possibility. Further, the rate of direct electrodeposition from the organic phase can be improved significantly by using an aqueous/organic mixture. Direct electrodeposition of sheet gold from loaded DBBP was successfully accomplished at a current density of 8x10 4 amp/cm2 and 55°C from such a two-phase mixture with the aqueous phase as the continuous phase. No appreciable degradation the DBBP was found after 5 cycles of extraction and, electrodeposition. Finally, the applicability of the process strategy for an industrial situation was demonstrated by the successful treatment of waste gold cyanide electroplating solutions.

Jan 1, 1986

By Marco D. Boscardin

During subsidence, the ground surface may settle, change slope, change curvature, go into tension, and/or go into compression. In response to these ground movements, buildings and buried utilities in the subsidence area may settle, tilt, bend, distort, and sustain extension, compression and/or torsion. In order to develop measures to protect existing structures and utilities, or to design new structures and utilities to withstand potential movements in areas of subsidence, it is necessary to understand the interaction between the ground and the building or buried the utility. This paper reviews subsidence-induced ground movements, how these ground movements are transmitted to and accommodated by buildings and buried pipelines, and how these structures may alter ground movements relative to free field subsidence-induced ground movements.

Jan 1, 1986

By Ruiren Jin

In alkaline pulp, galena is depressed by sodium carboxymethyl cellulose (NaCMC), while Cu(II)-activated sphalerite exhibits a high flotability so that satisfied separation can be achieved. In addition to hydrogen bonding, chemical bonding of NaCMC with galena is confirmed by IR; only hydrogen bonding is involved between NaCMC and Cu(II)-activated sphalerite. It is also found that the greater the degree of substitute and polymerization of NaCMC, the stronger the depressive effect of NaCMC and that lower stirring speed favors the depression.

Jan 1, 1987

By Gh. Crutu

During exploration and exploitation of complex ores, waste dumps that contaminate severely the environment and in particular soils and waters, are genetated. The most hazardous pollutants are heavy metals and metalloids (e.g As, Mo, Pb and Cu) as well as radionuclides (e.g U and Ra).

Jan 1, 2008

By Bruno A. Fichna

Longwall mining offers low cost potential for coal with high capital investment. As opposed to two shifts-per-day operation in most long- walls, Saarberg Mines in Germany increase utilization of capital by operating their longwalls around the clock. Differentiation between capital and operating costs, corrective maintenance versus preventive maintenance, improved roof conditions, and economical life of equipment was investigated. A surprisingly high degree of improvement was attained. Capital costs at Saarberg longwall coal mines have been reduced through a step-by-step research and trial program. This reduction was particularly influenced by the high performance pilot longwalls at the Ensdorf mine. The following presentation shows data and figures of those longwalls. End results were 40% reduction in capital costs, which could contribute favorably to investment decisions in the coal industry in a supply side economics environment.

Jan 1, 1982

By David M. Kjos

Large diameter autogenous and semi-autogenous grinding mills represent the primary thrust of the expanding grinding technology. In spite of initial difficulties, large autogenous and semi-autogenous mills have reached an acceptable level of technology which provides the mineral engineer with a reliable, low cost means of ore comminution. A successful milling installation begins during the design stage of the grinding mill and the plant it is to be installed in. This is particularly true in autogenous and semi-autogenous mills. Critical mill and plant design factors should be considered while the mill and installation are still only ?paper.? Various current liner designs will be discussed ranging from lifter bar/plate to integral types. Modes of operation such as "high-low" will be considered. Liner maintenance procedures ranging from laydown area in plant design, proper mill shutdown methods, to installation and bolt tightening complete the equation to yield optimum performance possible for any particular grinding application. The objective of this paper is to discuss trends in wear materials, designs and operating practices, and provide some guidelines for good practice as we move through the 1980's. We will put together concepts that relate to the designs, materials and applications so that higher performance can be obtained by the operator for his specific application. The concepts are shown as being in series because they are dependent on each other to achieve the desired performance.

Jan 1, 1985

By T. P. Harrington

Research efforts are just beginning to identify the acoustic signatures of very short pulses of sound associated with the fracture of single particles in an autogenous mill. This presentation will discuss the anticipated correlation between these data and the fundamental mechanisms of rock fracture It is hoped that further tests will help identify what design and operating parameters influence the acoustic spectra, determine whether different minerals have different spectra and correlate product particle size distribution with acoustic spectra.

Jan 1, 1980

By Yoginder P. Chugh

The term "fatigue" in mechanics, is used to refer to reduction in the strength of a material subjected to fluctuating or alternating stresses. Stresses that vary with time are called fluctuating stresses and if during fluctuation the stresses also change sign, they are called alternating stresses. In the field of rock mechanics, the term fatigue (static fatigue) has often been misused to refer to failure of geologic materials in time domain under constant load. To avoid confusion, we use the ten cyclic fatigue here to refer to failure of rock under alternating or fluctuating stresses. Fatigue in metals has been studied for over 100 years. Fatigue properties of geologic materials have, however, received little attention in the past. This is probably because until recently very little was known in regard to the behavior of geologic materials even under static loading. Secondly, suitable equipment for conducting cyclic fatigue experiments was not available until quite recently. A few cyclic fatigue studies have been undertaken on geologic materials to relate it to percussive or rotary drilling mechanisms (e. g. Grover et a11*; Burdine2). The results of these studies were inconclusive due to limited effort. Cyclic fatigue in concrete has been studied more extensively than geologic materials (e.g. Nordby3, Gray et al 4 and Bennett et a15) and mechanisms of fatigue in concrete are better understood than in geologic materials.

Jan 1, 1975

By K. McG. Bowling

A statistically-designed exper¬mental study showed how gangue minerals, flux additions, fineness of grind, firing temperature and time affect the properties of acid pellets made from a Western Australian hematite ore. Alumina has less effect than silica and lime, but various interactions between the six variables occur, which influence abrasion index, reducibility and cold compression strength. Finer grinding has little influence on reducibility but improves the other two properties. The major variable is firing temperature. It interacts with all other variables in its effects on pellet properties. Calculations based on the data show the implications for straight-grate pellet plants and optimum hood temperature range.

Jan 1, 1980

By K. Lapakko

Kinetic tests results are influenced by methodological variables, including test duration and mine waste particle size. Some samples tested produced neutral drainage in kinetic tests for more than two years prior to drainage acidification. The potential for long "lag times" can be assessed based on the mine waste mineralogy. The lag time duration can be estimated using this mineralogy in conjunction with dissolution rates observed in the kinetic tests. The influence of particle size on the drainage quality is dependent on the variation of the availability of acid-producing and acid-neutralizing minerals with particle size.

Jan 1, 1998

By A. D. Walters

Computer simulation models of preparation plant operations and cost analysis have been used to determine the profitability of individual coals. The model's input consists of raw coal size and washability analysis, operating cost data, and raw coal and clean costs. The model's output predicts yields, qualities, costs and profitability for an individual coal.

Jan 1, 1987

By Clarence A. Johnson

The discovery of the Prudhoe Bay field temporarily reduced interest in the development of coal conversion processes, but interest is being re¬newed by the current energy crisis. According to M.A. Wright, Chairman of the Board of Humble Oil and Refining Company(l), the reserve in the Prudhoe Bay bield has been confirmed to be about 10 billion barrels. At first glance this appears to be an extremely large reserve which will eliminate supply problems for the United States for some time. This feeling of security is lost when one realizes that by 1980 the world will consume the reserves of a Prudhoe Bay or a Libya, or Venezuela in less than a year, based on the recent predictions of U.S. and world reserves made by Eastman-Dillon, Union Securities Company(2). Recent forecasts of U.S. demand and source of supply made by Kenneth E. Hill of Eastman-Dillon are shown in Figure 1. This forecast shows a decline in domestic supplies (excluding Alaska) after 1973, with the total domestic supply leveling off in 1975 at about 13 million barrels per day. Since the predicted demand increases from about 14 million barrels per day in 1970 to about 20 million barrels per day in 1980, about 35% of domestic consumption must come from imports or non-conventional sources by 1980. More imminent is the shortage of low sulfur fuel oil which has been created by the new, tough air pollution regulations that are basically legis¬lating eastern coals out of the market. As an alternate to importing large quantities of low sulfur fuel oil or importing and desulfurizing regular fuel oil, one of two domestic solutions is possible: stack gas clean-up or solids fuel pretreatment. Stack gas clean-up may be the cheapest approach for old installations, but fuel pretreatment has real advantages for new installations. Coal pretreatment at the mine could eliminate all solids fuel handling

Jan 1, 1972

By T. Karlkvist, H. R. Kota, F. Andreas, B. I. Pålsson

"Separation of different calcium minerals have long been an interesting and challenging problem. In this investigation calcium mineral separation is examined by: microflotation, zeta potential measurement and adsorption, using novel collectors having two functional groups instead of one. In theory, by varying the distance between the functional groups, it could be possible to preferentially target one calcium mineral by matching the spatial distance between the sites on the mineral surface. In this investigation two new surfactants have been tested to estimate their ability to float apatite and/or calcite. Preliminary findings show that an increase in distance between the functional groups favors one mineral over the other, and this might be due to differences in the mineral surface structure. INTRODUCTION Apatite is a strategically important mineral which has both great value for industrial use as a precursor to phosphoric acid; and in the agricultural industry as an important source of phosphorous in fertilizers. This has led both the European Union and the United States to recognize it as an important resource for the future. Currently there is no lack of apatite in the world, but it is important to develop the beneficiation to ensure future supply. A common problem in apatite flotation is the selectivity towards calcite, which it is commonly associated with. Although calcite is an important industrial mineral its abundance makes it not usually worth to extract from apatite ores unless it is easy to separate1,2. Both apatite and calcite are semi soluble minerals with calcium as one of their constituents. The most common way to separate apatite and calcite is to use flotation. A process that involves making the mineral particles to extract from the system hydrophobic by adsorbing a collector on the mineral surface. One way to study collector adsorption on a mineral surface is by zeta potential measurements. The zeta potential is the charge at a slip plane a short distance from the surface. By measuring the zeta potential with and without the presence of collector it is possible to investigate if the collector is present at the surface or not, a change is indicative of collector adsorption. The zeta potential of fluorite, apatite and calcite without collector can be seen in Figure 1. The small difference in zeta potential between apatite and calcite shows the similarity in their surface properties and gives an indication of their separation difficulty. One additional problem with semi soluble minerals is their tendency to slightly dissolve in the pulp and thereby change the ionic composition of the solution. This makes separation and research problematic as the freed ions may readsorb on the mineral surface and interfere with the collector adsorption on the mineral surfaces3–5."

Jan 1, 2016

By B. V. Clingan

A practical application of recent design concepts makes it possible to design a column cell to fit a specific set of conditions. The design and operating parameters Of a column cell installation that replaced a conventional two stage copper flotation cleaning circuit at MAGMA COPPER COMPANY, SAN MANUEL, ARIZONA using these design concepts is described. A survey of other mineral processors using column cell technology was conducted. The results of this survey will also be discussed.

Jan 1, 1987

By J. Astier

The idea of using only one strand for both sintering and cooling of the sinter is not new. In 1952, in the U.S.A. a sintering plant was built at Benson Mine (Star Lake, N.Y.), including : - 68 m2 or 735 sqft (8 wind boxes) for sintering, - 22 m2 or 237 sqft (3 wind boxes) for cooling. In the USSR, a large number of machines have been built allowing for cooling of the sinter on the strand, especially the 4 m (about 13 ft) machines, with : 252 m2 sintering grate area 60 m2 cooling grate area 312 m2 total grate area. However, such ventures did not prove very successful, and the IRSID embarked many years ago on a research program to discover : - what are the problems associated with cooling on a sintering strand ; - what are the possible solutions for industrial plants.

Jan 1, 1974

By Y. J. Wang

The definitions of system pressure loss (mine head) and system resistance, which are traditionally associated with single-fan net- works, are applied to multiple-fan ventilation networks. The system characteristics -- relations among air power, pressure loss, air quantity and resistance -- are analyzed by introducing the concept of subsystems. These subsystems are associated with the fans located in a cutset of the network. For a multiple-fan network, the resistances for the subsystems and total system are dependent on the quantity ratios of the subsystems. In general the pressure loss of a subsystem or a total system does not vary as the square of the corresponding air quantity. If the quantity ratios of subsystems are all held constant, then the resistances become constant and the pressure losses are predictable from the quantities employing the "square law." The system resistance has a minimum value under the natural- splitting flow pattern. Being independent of the value of system quantity, the minimum system resistance provides a basis for comparing the different networks.

Jan 1, 1983

By R. W. Brann, R. C. Freas

Franklin Industrial Minerals operates several mines/quarries, including two room and pillar underground mines. Both of these mines are operated as multiple level room and pillar including heading and bench operations on one or both of the levels. This paper focuses on Franklin’s Crab Orchard, Tennessee mine, which produces both high purity chemical grade limestone and crushed stone for construction applications. The high purity chemical specifications for the chemical grade limestone and filler/extender applications are inconsistent with the non-chemical rock being produced to supply the crushed stone market. As a consequence Franklin has developed a unique mine plan and operation to maintain both product balance and a safe and stable working environment.

Jan 1, 2003

By Melvin W. Dadd

[One of the major problems in the purchase and sale of coal shipped in lake or ocean going vessels has always been the difficulty in obtaining a true analysis of the shipped coal?s quality because of faulty sampling by manual methods. As long as coal was sampled according to standards set up by ASTM methods designated D 492-48 there generally were no quarrels with the results obtained. However, due to varied weather conditions and because of the large number of cars sampled, there is no assurance that prescribed manual methods of sampling will always be followed. Because of this problem, the organization previously called American Coal Sales Association, now part of the National Coal Association, set up a committee compose of representatives from coal producers, coal shippers and coal consumers to study this sampling problem and to devise, if possible, a means of sampling on the high lift dumpers which could be automated so that a; true sample of the coal as loaded in the railroad car could be obtained.]

Jan 1, 1962

By Ramarao Inguva

Feasibility studies being conducted to investigate the use of electromagnetic methods for insitu volumetric heating of oil shales will be discussed. A two dimensional numerical model which describes eletromagnetic heating of oil shales is outlines. The model includes equations for temperature, pressure, saturations, chemical reactions, mass conservation, and source terms. The gases are all assumed to form one bulk species and the oil is assumed to remain in liquid form. The chemical reactions include pryolysis of kerogen and char, release of bound water, coking, and decomposition if carbonates. Porosity and permeability are dynamic functions of the organic materials. Calibration of the model is accomplished by comparison of the model results with experimental data obtained by IITRI. Nonlinear relationships for viscosity, thermal properties, and source terms and used as inputs to the model. A finite difference approximation to the differential equations is derived and solved using Newton's iteration technique. For the cases studied the solutions are quite stable. Numerical resultes are included and a preliminary study of the optimization of the heating process is presented.

Jan 1, 1984

By J. D. Patsey

A computer program has been developed for use by the mining engineer for analyzing drum-type hoists prior to the modification of an existing system or the designing of a new one. Its use permits the preliminary evaluation of a system before seeking the technical assistance of mine hoist designers and manufacturers. Compatible with an IBM-PC, the user-friendly program accepts a variety of data and can analyze hoisting systems for any balance state. The extensive program can be used to: (1) calculate skip capacity to yield a desired production rate; (2) solve for required drum face width; (3) select a permissible wire rope from a menu of 50 available rope types: (4) estimate total horsepower of the hoist plant; and (5) estimate power cost. An example of the model's use in evaluating a hoisting system will conclude the paper.

Jan 1, 1986