Search Documents

By Nathaniel Arbiter

The increasing size of flotation cells as the use of flotation has increased is traced from the first United States application of the process in Montana in 1911 through the following eight decades, using data from the Taggart handbooks (1927) and (1945), from the SME Handbook (1984), and from recent manufacturers' catalogues and other sources for the 1980s and 1990s. With the earliest mechanical cells less than 1 m3 (359) in volume and the largest now available at 200 m3 (7,000ft3), three requirements are necessary: 1) demonstration of advantages in replacing smaller volume by larger volume cells; 2) estimating power requirements, impeller dimensions, and operating rpm by correlation equations; 3) considering effects of using larger cells, in necessarily much shorter rows, on process kinetics. The resulting seven tables that address these problems are presented, and their implications discussed.

Jan 1, 1999

By J. P. Hanten, G. Ramadorai

This paper presents laboratory and pilot plant data on the removal of heavy metals and molybdenum from mining-milling waste water. Molybdenum is removed as an Fe-Mo precipitate by proper addition of ferric sulfate. Heavy metals are lowered by lime treatment. Solid-liquid separation was achieved in both cases by flotation techniques. The Lectroclear electrocoagulation-electroflotation process was used to achieve the desired degree of metals removal. Good correlation was obtained on the laboratory and pilot plant scales. A two-step process consisting of the sequential removal of molybdenum and heavy metals was tested successfully using a mobile pilot plant. Preliminary data on sludge characteristics was obtained and the feasibility of recycling the iron sludge for iron and molybdenum recovery was established on the laboratory scale.

Jan 1, 1987

By N. Edmonson

A review of the evolution of the North American sulfur market's structure serves to dramatize the kinds of changes that the market is undergoing at the present time. In 1970, the U.S. accounted for 23 percent of world sulfur production. This share has not declined dramatically--to 21 percent in 1993--but the U.S. developed into a substantial net importer of sulfur in the past 25 years. U.S. output was based on large deposits of native sulfur in the western part of the Gulf Coast region with production by the Frasch mining process. Producers of Frasch, or on-purpose sulfur, have historically absorbed cyclical fluctuations in sulfur demand. Two major changes in the North American market from that time to now have been the introduction of increasingly large quantities of by-product sulfur from petroleum refining and natural gas processing operations in the U.S. and Canada, and that Canadian producers have become the marginal supply source for U.S. sulfur consumers.

Jan 1, 1996

By Byron R. Berger

Epithermal Ag-Au deposits form at low to moderate temperatures in near-surface environments. Historically, these deposits have been the source of high-grade ores. Increases in the market prices for gold and silver make lower-grade ores economically viable when available in large tonnages. Both the high-grade and bulk-tonnage ores are a consequence of the same processes, and general models of epithermal systems can be useful in the search for new precious-metal resources. A detailed study of deposits at Round Mountain, Nevada; Balei, Russia; Creede, Colorado; Guanajuato, Mexico; and Chanarcillo, Chile, indicates that the hydrodynamics of the fluid systems as determined by fracture geometries, the permeability, and composition of the host rocks are the key factors in the creation of both high-grade and bulk-tonnage epithermal deposits. End-member models that explain the range of observed deposit characteristics are: (1) the hot-springs deposition model; (2) the stacked-cell convection model (where mineral deposition occurs laterally along the interface of two partially separated fluid reservoirs); and, (3) the closed-cell convection model (where deposition occurs in vertical zones due to the relatively unimpeded vertical flow of hydrothermal fluids). Boiling and fluid mixing appear to be agents of precious-metal deposition with the self-sealing of the hydrothermal system being an important adjunct to boiling. Imaginative application of model concepts in exploration has led and can lead to the discovery of new high-grade and/or bulk-tonnage precious-metal deposits.

Jan 1, 1982

By P. Schumacher, M. Fein

"INTRODUCTION Newmont’s Twin Creeks operation, part of its Nevada operations, produces gold from two large open pit mines. Mined ore is processed at one of three on-site facilities: a refractory mill with two autoclaves, an oxide mill and heap leaching facilities. Twin Creeks also processes various off-site sourced concentrates and ore including high grade underground ore from the Turquoise Ridge joint venture with Barrick Gold Corporation. This paper discusses Twin Creeks’ strategic mine planning process which is part of an in-depth continuous improvement program called “Full Potential.” The process involves cost analysis, phase design validations, life-of-mine production scheduling optimization, mill blending strategy and stockpile management. Through this Full Potential strategic planning, Twin Creeks is creating significant value by increasing near term free cash flow and life of mine net present value (“NPV”) and achieving cost reductions. TWIN CREEKS OPERATION Twin Creeks is one of the major gold producers in Newmont’s Nevada operations (see Figure 1, 2 and 3). Located approximately 15 miles north of Golconda, Twin Creeks produced approximately 28 % of the Nevada operation’s 2013 gold production of 1.8 million ounces (Newmont 2014). The production included Turquoise Ridge sourced gold ore from the joint venture (75% Barrick Gold Corporation, 25% Newmont).At Twin Creeks, there are two large open pits, named Mega Pit and Vista Pit (see Figure 4, 5 and 6). There are 3 to 5 phases in Mega Pit and 2 to 5 phases in Vista Pit depending on the gold price assumption. There is also an underground exploration project at the bottom of the Vista Pit. Twin Creeks produces gold from a variety of ore types requiring different processing techniques depending on economic and metallurgical characteristics. To ensure the best use of processing assets, engineering and processing groups at Twin Creeks utilize a Mixed Integer Linear Programming (“MILP”) model to guide the flow of mine sequences and material routing to various process facilities (Kawahata, Schumacher and Hufford 2013)."

Jan 1, 2015

By J. L. Heaver

All complete plant foods require phosphorus, nitrogen and potassium. And phosphate rock is the primary source for the phosphorus of the inorganic fertilizers. As more and more world food production is grown with these chemical fertilizers and since the Florida field supplies over 30% of the phosphorus component, let us look at the vital phosphate industry. Mining of phosphate rock in Central Florida began in 1891 and production has continued to grow at a steady pace. In 1965 a phosphate mine was opened in Hamilton County, North Florida and one in Beaufort County, North Carolina in 1966 . Since the beginning of mining in 1891, approximately 700 million metric tons of phosphate rock have been produced of this amount one-half was mined in the last 11 years. While the field was not deliberately "high-graded," the best of the known deposits were mined first. Those now being mined, and those yet to be mined, cost more to operate and the product is of lower grade. The U. S. Bureau of Mines' data for 1977 lists "Florida" phosphate rock production as 40.6 million tons; 86% of U. S. production and 85% of "Florida" capacity. The U. S. Bureau of Mines includes North Carolina production in "Florida" statistics so as not to reveal individual data for the one mine operating there. Approximately one-half of "Florida" production is exported, either as rock or as rock equivalent in upgraded products. Deposits of phosphate rock necessary to support present and future production are catalogued as: reserves, paramarginal reserves and resources. Reserves denote deposits which can be mined at a profit now. Paramarginal reserves are defined by the U. S. Bureau of Mines and the U. S. Geological Survey as: that portion of sub-economic resources that a) borders on being capable of production economically, or b) is not commercially available solely because of legal or political circumstances. The " b)" part of this definition may now be expanded to include environmental controls and requirements. Resources are deposits which cannot be mined at a profit at present. Listed in Table I are reasonable values for each of the three categories of phosphate deposits in the northern and southern parts of Central Florida. North Florida and North Carolina.

Jan 1, 1978

By D. Malhotra

Metallurgists are continuously striving to improve recovery. But optimization of profits and/or revenue dictates that recovery can be sacrificed at the expense of throughput. However, recently there has been significant interest in the concept of retreatment of tailings to enhance recovery and hence revenue while maintaining high throughput. The authors discuss the technical and economic factors that need to be considered in evaluation of the feasibility of retreatment of tailings including the potential feed streams (i.e., rougher tailings, cleaner tailings, etc.) and processing options (i.e., physical beneficiation, chemical processing, etc.). A case study for base metals is discussed.

Jan 1, 1994

By K. Neumann

"INTRODUCTION For many automation and safety tasks in open cut and underground scenarios it is crucial to have highly reliable distance measurements at hand. These measurements can for instance be used to obtain the exact position of a machine in one-, two- or even three dimensions. Research and development has shown interest in the ultra-wide-band technology (UWB) in recent years. While for this technology short range, high speed data transfer is the current main research focus, the technology can also be used for highly accurate ranging applications. Due to the use of a very wide frequency band, it is robust against disturbances of many types (e.g. EMC, rain, dust etc.) and is therefore attractive for the use in mining applications. The wide frequency band also offers benefits for ranging applications. Especially in environments with strong multipath problems such as in underground mines it is possible to focus on the dominant signal propagation path, thus increasing the reliability of the measurements. [1] State-of-the-art UWB ranging equipment claims precision within the range of a couple of centimeters and working ranges of more than hundred meters. At the Institute for Mining and Metallurgical Machinery (IMR) at RWTH Aachen University in Germany a modern UWB system was examined in several laboratory and real life tests to examine the feasibility of UWB bases ranging equipment in mining applications. UWB TECHNOLOGY The term ultra-wide-band denotes radio systems that use an ultra-wide frequency band. A common definition for UWB radio systems is that it needs to work on a frequency bandwidth of more than 500 MHz or a bandwidth equal to 20% or more of the center frequency [1]. Due to the ultra-wide frequency bandwidth UWB systems overlap the frequency spectrum of narrow band radio technologies like Wi-Fi, Bluetooth and other mobile communication systems which use a defined carrier frequency onto which information is modulated on (e.g. by using frequency or phase modulation). In order to not conflict with these other radio applications, it needs to be ascertained that the transmission power of a UWB system on a given frequency is so low that narrow band systems are not affected by it. As opposed to this only a small fraction of the UWB system’s bandwidth is affected by the narrow band system. The unaffected remaining bandwidth is sufficient to reconstruct the original signal, even if additional noise is present. Figure 1 shows the power spectral densities of popular radio standards [6], [7], [8]. A significant driver of research and development of UWB systems has been wireless high bandwidth communication. Using an ultra-wide frequency band is highly desirable here, as the channel capacity is dependent on the bandwidth. So far systems have been realized especially for short distances (e.g. wireless USB or Wireless HDMI) but beyond that, communication systems for long distances (several kilometers) are possible [2]. Advances in semiconductor technology led to a reduction in power dissipation of such systems. This enabled higher integration levels which in turn facilitated smaller solution sizes for space constrained applications [3]. Nowadays, UWB is also used for high-precision ranging applications [4], [5]."

Jan 1, 2015

By Hillary W. St. Clair

In a previous report 1/the author showed that the essential information from particle size analyses of grinding mill products can be represented by three or four parameters derived from the first four moments of the particle size data. These parameters may be used in gamma or beta distribution functions to estimate the weight fraction in any given size range. Moment analysis was used to study the progressive changes that take place in particle size distribution when a homogeneous isotropic mineral such as quartz is reduced in size by impact crushing. 2/ This report briefly reviews the essential features of moment analysis and describes extension of this method to size reduction by ball mill grinding.

Jan 1, 1972

By J. L. Carr, A. K. Smith, C. C. Jobes, G. T. Homce

"Underground continuous mining machines pose a difficult safety challenge since their operators generally work in close proximity to these machines in very restricted spaces. Intelligent software for use with magnetic proximity detection systems has been shown to accurately locate workers around mining machinery in real time. Calibrating these systems requires the manipulation of a lot of data to determine the calibration constants. Researchers have developed software to analyze, convert, and visualize data acquired during this calibration process to more accurately model magnetic fields and their interaction with the environment. This paper details the background, development, and operation of the resulting application software focusing on the utility of the graphical user interface to visualize the magnetic field calibration data. The refined data developed by this process can then be utilized by the proximity detection system to more accurately identify the location of miners working in an underground mining environment. INTRODUCTION Roughly half of the electricity consumed in the United States is produced with coal, and roughly one-third of all US coal production comes from underground mines [1]. Over the last century underground mining health and safety has seen a continuous and dramatic improvement. However, machine-related injuries and fatalities continue to be a major safety concern [2]. Every year, hundreds of miners are severely injured while operating underground mining equipment, and 39 miners have been killed in striking/pinning accidents involving continuous mining machines (CMMs) since 1984. CMMs, such as the one shown in Figure 1, are large mobile machines that are used to mechanically cut coal in an underground mine. These machines weigh approximately 40 to 50 tons, have hydraulically articulated appendages, and are capable of moving at speeds up to six feet per second [3]. Modern CMMs are remote-controlled, yet the operator and other miners are often in close proximity to the machine. Recent research by the National Institute for Occupational Safety and Health (NIOSH) reveals that the locations workers take relative to the CMM are usually influenced by visibility requirements and safety concerns [4]. The Mine Safety and Health Administration (MSHA) estimates that at least 28 fatalities involving CMMs since October of 1984 may have been prevented with proximity detection technology [5]. MSHA further estimates that proximity detection could prevent 20% of all deaths throughout the industry [6]."

Jan 1, 2016

By Christopher E. Dianora, Matthew Sorrell, Eileen Test

"Constructed between 1939 and 1945, the Rondout-West Branch Tunnel (RWBT) portion of the Delaware Aqueduct is 45 miles (72 km) long. The New York City Department of Environmental Protection (NYCDEP) first identified suspected areas of leakage from the RWBT in the 1990s. A $1 billion project is underway to mitigate the leakage through the construction of a bypass tunnel around the area of most severe deterioration, a 2.5-mile (4 km) section located beneath the Hudson River. Two shafts, 800 and 900 feet (244 and 274 m) below the ground surface, are being sunk to support the tunnel construction. The deep shafts will be subjected to high groundwater pressures and have been designed to accommodate multiple tunnel portals. This paper discusses the engineering decisions and analyses leading up to the final design. INTRODUCTION Project Background The New York City Department of Environmental Protection (NYCDEP) provides over 1 billion gallons (3.7 billion liters) of water to over 9 million residents of the City of New York and surrounding communities each day. This water is stored in upstate reservoirs and conveyed to the City via a system of aqueducts and tunnels. Water is delivered to the City almost completely by gravity and consists of three systems: the Croton, the Catskill, and the Delaware. The Delaware System is the largest of the three and supplies between 50% and 70% of the City’s daily water supply. In the 1990s, the NYCDEP discovered leaks in the central 45-mile-long (72 km) portion of the Delaware Aqueduct known as the Rondout-West Branch Tunnel (RWBT). The leaks release between 15 and 35 million gallons per day (MGD) (132.5 million liters per day) and are concentrated in two areas near Wawarsing and Roseton, New York. As part of the Rondout-West Branch Bypass Tunnel and Wawarsing Repairs Project (Bypass Tunnel Project), the leaks in the Wawarsing area will be repaired by grouting from inside the existing RWBT, and the leaks in the Roseton area will be mitigated by constructing a bypass tunnel parallel to and 1,750 feet (533 m) north of the leaking portion of the existing RWBT. Two deep shafts will be excavated on either side of the Hudson River: Shaft 5B in Newburgh and Shaft 6B in the Town of Wappinger."

Jan 1, 2016

By J. García, B. Arango, F. Calderón, O. J. Restrepo-Baena, A. Carreno, L. Rojas-Mendoza, J. Pérez, E. Bedoya

"Tungsten extraction is a subject of global interest due to is properties. These properties, such as its high melting point, have contributed to the development of metallurgical extraction processes that can be adapted to the particular chemical composition and mineralogy of the ore. In Colombia there is a research deficit in tungsten related areas, and especially with regard to its extractive metallurgy. In this study the physical, chemical and mineralogical characterization of a sample were performed. Subsequently, crushing and grinding were employed to reduce the material to a more convenient size, making it suitable for further concentration and metallurgical processes. Through physical concentration techniques it was obtained a concentrated ranging between 60 -70 % of WO3 content.INTRODUCTION Tungsten is a metal of great economic importance due to its excellent properties such as high density and extraordinary melting point 3422°C), which is indeed the highest of all the elements. Tungsten is primarily used in metal alloys, manufacture of special steels, coatings and catalysts; products of interest to both international and national industry. However; given that the use and economic value is determined by the percentage of tungsten in the mineral, particle size and chemical associations, it becomes essential to properly characterize the mineral to further define possible metallurgical extraction routes. The metallurgical processes for minerals enriched in tungsten may vary depending on location and the genesis of the ore body, which means that for each ore a particular set of operating conditions must be determined. This is important since process standardization can lead to misuse of the mineral resource. However, in Colombia there is a research deficit as it relates to minerals enriched in tungsten and to its extractive metallurgy. Then, there is a need to conduct studies that can lead to a better understanding of the ore, and to develop extraction processes for the metal of interest. EXPERIMENTAL A state of the art review was made in order to gain insights of the tungsten metallurgical process. Comminution was necessary with the aim to reduce the sample size; therefore the sample was taken into crushing and grinding stages. Concentration techniques such as magnetic separation, gravity and / or electrostatic were also applied. Physical, chemical and mineralogical characterization were performed by using polished sections, grain size determination, X-Ray Fluorescence (XRF) and X-ray diffraction (XRD) techniques."

Jan 1, 2015

By J. W. Parkinson

With most of the coal currently mined in the eastern U.S. already requiring cleaning to meet electric utility coal specifications, the question remains how medium- and high-sulfur coal producers will provide the even better quality coal expected to be demanded if pending acid rain legislation is enacted. One emerging approach is to crush the coal to liberate additional ash and sulfur so that better quality coal can be produced at equal yields. This paper discusses how to measure liberation. the premiums the utility market is willing to pay for lower sulfur coal, and a staged middlings crushing scheme that promises the benefits of total raw coal crushing but at lower costs. For some coals, cautious application of liberation concepts may be the only way to produce a product that can be quality and cost competitive in the future utility coal market.

Jan 1, 1988

By T. A. Toney

A sampling program was conducted in 2008 to determine the run of mine characteristics of 5 coal seams. The sampling program included size analyses and float sink determinations. The samples were analyzed for ash and mercury concentrations for each size and gravity fraction. This paper will report on the sampling program, the analytical results, and the correlations determined in the data set investigated.

Jan 1, 2010

By John C. Morrisey, Harold M. Ray

With full production from the Casteel Mine in 1987 The Doe Run Company, a wholly owned subsidiary of the Fluor Corporation, encountered a significant increase of copper and iron to the Viburnum Mill. This major change of the lead, zinc, and copper metal ratios in the ore created circuit problems which adversely affected concentrate quality. Recognizing the problem, the company embarked on a metallurgical research program to include laboratory, pilot plant, and plant testing. The program developed an innovative copper prefloat process which both increased copper recovery and significantly improved concentrate quality. The process was tested and first operated at Doe Run's Brushy Creek Mill then installed at the Viburnum Mill in 1992. A brief history of development, plant operating data, and other potential applications for the patented processes will be described in the paper.

Jan 1, 1993

By Scott Lewis, Andrew Kositsky

"INTRODUCTIONThe South Napa Earthquake of 2014 caused ground motion at numerous reinforced concrete-lined (shotcrete-lined) winery tunnels in Napa County and Sonoma County, California. The occurrence of seismic ground motion at these tunnel complexes, known as wine caves, presented an opportunity to reevaluate seismic performance of reinforced concrete and reinforced shotcrete lined tunnels. The authors of this paper updated the most recent comprehensive compilation and evaluation of case studies by Power and others (1998), which correlates peak ground acceleration (PGA) at tunnel sites to damage. For this update, the authors evaluated the seismic performance of 31 wine caves near the South Napa Earthquake epicenter; including some of the 90 wine caves they designed since 1991, some caves designed by others, and additional caves constructed by contractors that they frequently work with. Tunnel designers can use the new data presented in this paper to help evaluate the usefulness of detailed seismic design analyses. THE SOUTH NAPA EARTHQUAKE The South Napa Earthquake occurred at 3:20 AM Pacific Daylight Time on August 24, 2014. Figure 1 shows the approximate location of the epicenter, the measured/estimated PGA contours, and the location of wineries with wine caves added to the database where the PGA was at least 0.2 g. The epicenter was along the West Napa fault, about 5 miles south-southwest of downtown Napa, California. The earthquake moment magnitude was 6.0, and measured/estimated PGAs were up to about 0.7 g. The duration of strong shaking was about 10 seconds. This earthquake was characterized by right lateral strike-slip fault movement, ground surface rupture, and after slip at the ruptures. Increased surface water flows were observed at seven creeks after the earthquake. Groundwater level rises of up to 5 feet were observed in Sonoma County wells after the earthquake. The earthquake was the largest seismic event in the San Francisco Bay Area, which includes Napa and Sonoma Counties, since the 1989 Loma Prieta Earthquake. The Napa event caused an estimated $400 million in damage. This damage included moderate to extensive structural damage to older commercial buildings and to some newer buildings in downtown Napa. This damage resulted from ground motions, subsequent fires, and failed underground utility systems."

Jan 1, 2016

By B. Govindarajan, T. C. Rao, M. Vanangamudi

The results obtained from hatch, flotation experiments on two coals were used to develop relationships between the recoveries of water and solids into the concentrate. When the recovery of non-ash material (RN) for any size fraction is plotted against a parameter X, defined as [x _ Amount of (W) recovered x Collector dosage (C)in the concentrate (cc)(kg/t)] a single "non-ash recovery curve" is obtained. Non-ash recovery curves thus obtained from different size fractions are used to get a unique "modified non-ash recovery curve" for a given coal, using the reduced efficiency curve concept. Similar observations have been noted in the case of recovery of ash material (RA) also. The amount of water recovered into the concentrate is plotted against a parameter "Water Recovery Factor (WRF)," defined as [WRF = T.F.(1+C)] where T is time (in sec) and F is frother dosage (in kg/t). Plotted in this form a characteristic water recovery curve, for a given coal is obtained that may be defined by the following equation: [W4=W_(1 pWRF-e] The above relationships have been verified against the experimental results obtained from three more coals and are found to give satisfactory predicted values.

Jan 1, 1992

By B. C. Paul, R. Q. Honaker, M. Huang

Froth flotation is now, the most commonly used method for cleaning fine-coal fractions in coal-preparation plants. Past research and industrial practice have demonstrated that froth flotation achieves excellent separation efficiencies for fine coals having only a small fraction of middling particles. However, the efficiency of froth flotation decreases sharply as the concentration of middling particles increases. This is due to the flotation of high-ash particles that have a small amount of hydrophobic coal present at the surface. Because gravity-based processes are much more efficient for the treatment of middlings, the application of centrifugal washing for fine-coal cleaning was studied with an emphasis on the primary cleaning of fine-circuit feed. Results are shown of a parametric study that used a semibatch Falcon centrifugal concentrator. The results of the study revealed that separation performance is a function of particle size, bowl geometry, feed solids content and feed rate.

Jan 1, 1996

By C. W. Schultz

Earlier publications from The University of Alabama have indicated that column flotation performance is improved when operating at low pulp levels and when the feed is directed into the froth phase. To validate these early observations a series of tests were performed in which the position of the feed entry to the column and the pulp-froth interface were systematically varied. The optimum grade-recovery relationship was achieved with high feed entry (WA) of column height) and very low pulp levels (<10% of column height). The position of the pulp-froth interface appears to be the more critical variable. When operating in this mode (1. e. at low pulp levels) column flotation becomes. in reality. a froth separation process.

Jan 1, 1991

By Jacques B. Wertz

Although fracture intersections and "domes" seem at a number of places to be the basic structural combination for the occurrence of a mining district, of the porphyry-copper type particularly, this situation is, of course, not always to be expected. For instance, the group of mines comprising Superior, Ray, Miami, Globe, Christmas appeared from the beginning of these structural studies as typical exceptions, and there are others. One had to expect additional parameters to allow for any mineral concentration to occur. One of these apparent parameters is here considered. From the result of stratigraphic studies related to ancient formations in Southeast Arizona, the Martin limestone (Devonian in age) was retained as having a possible relationship with the structure-economic studies in progress, as evidenced for instance by the mineralized O&apos;Carroll bed located at the base of the Martin. This limestone formation has been rather extensively investigated in the past and there are many known sample localities. For this work, the isopach map was drawn by computer to insure more objectivity and, in addition to the available data points, a number of dummy points with a zero value were added around the assumed form-

Jan 1, 1971