Search Documents

By F. S. Knoll

Magnetic separation employing superconducting technology is now accepted within the Kaolin processing industry, proving the value of this technology and its ability to operate reliably even at the most remote site. Developments in superconducting magnet engineering, including cryogen free operation, combined with experience in mineral processing enables new forms of Wet and Dry superconducting magnetic separation to be developed. Applying the high magnetic force advantages at 5 T else available from such magnets to other materials is now a reality. High magnetic force mineral separating system developments are reviewed allowing the mineral processor to take advantage of a technology that is no longer confined to the laboratory.

Jan 1, 1997

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay

Accurately estimating load distributions and ground responses around underground openings plays a significant role in the safety of the operations in underground mines. Adequately designing pillars and other support measures relies highly on the accurate assessment of the mining-induced loads, as well as the load-bearing capacities of the supports. There are various methods that can be used to approximate mining-induced loads in stratified rock masses, both empirical and numerical. In this study, the numerical modeling approach recently developed at West Virginia University, which is based on the modeling approach developed by the National Institute for Occupational Safety and Health (NIOSH), is investigated using the finite difference software FLAC3D. The model includes the longwall panels, the adjacent chain pillar systems, and the different stratigraphic layers of the overburden. Using the 3D model, changes in loading conditions and deformations on the areas of interest, induced by an approaching longwall face, can be examined. This paper details the 3D modeling of a longwall panel utilizing this approach, and the verification of the results against field observations. The studied panel was 360 m wide with a 3-entry chain pillar system and about a 160-m average overburden depth around the studied area. The overburden strata consist of alternating layers of shale, sandstone, and limestone. The FLAC3D results were compared against field measurements from the mine site. The stress change values measured in the chain pillars were comparable with the modeling results. The model also replicated the surface subsidence profile obtained from field measurements fairly well. Overall, the 3D modeling approach was found to be successful for the case study longwall panel.

Sep 23, 2020

By J. P. Kennedy

Process data managers or historians are recognized as essential for reengineering projects in industrial plants. With increasing automatic data collection, the knowledge of how to use these data profitably grows as well. This paper is a summary of the data historian and its components plus examples of benefits including environmental reporting, performance monitoring, and exception reporting to management.

Jan 1, 1994

By Daniel R. Walton

This paper covers several points of interest to mine engineers and planners involved in evaluating or conducting geostatistical coal reserve estimates. In particular, the ability to optimize borehole drilling locations and minimize drilling costs is addressed. Also discussed is the concept of confidence intervals for estimated coal characteristics obtained through geostatistical estimates and their importance in decision-making for mine planners. Finally, a discussion is presented on how geostatistics enables identification of invalid data points and actually forces strict attention to data editing and proper geologic interpretation.

Jan 1, 1982

By Robert L. Frantz

The various facets of university-company cooperative activities and the opportunities for collaborative research for the mineral industries are presented in this paper. The advantages and disadvantages of various alternative research funding arrangements for the researcher, the university, and the sponsoring corporation are discussed. Examples of university-industry cooperative research programs are briefly outlined. The concept of a cooperative mining research program is presented. The improvement of performance through techno- logical developments and human skills may well be the greatest competitive edge available to the U.S. mining industry. In this regard, the need for new endeavors between industry and universities can hardly be overemphasized.

Jan 1, 1984

By Robert A. Pimentel

Dust is still a major problem in increasing production from longwall faces. Over the last decade, significant improvements have been made in the development of techniques for reducing dust exposure on conventional and continuous sections. But virtually no improvements have been made in dust control on longwall sections. It is true, that there are many more continuous mining sections than longwall sections in the United States and that the number of workers overexposed on continuous miner sections is much larger than the number on longwall sections. However, the problem on continuous miner sections appears much easier to solve and, in fact, we believe that the techniques are available to get virtually all continuous miner sections in compliance. The problems on longwall sections are much more elusive. Also, the number of longwall sections in the United States is expected to increase during the 1980's. Thus, dust control on longwall sections remains a formidable and important problem. Companies operating longwall sections with a dust problem are faced with the tasks of having to quantify the various dust sources, of selecting proper techniques to reduce the problem, of implementing the techniques and of evaluating their effectiveness.

Jan 1, 1983

By A. W. Khair

This paper presents an analysis of respirabie dust generation due to the action of a continuous miner. Underground coal cutting by a drum-type continuous miner was simulated in the laboratory using a specially designed unique automated rotary coal cutting simulator (ARCCS). An analysis of -400 mesh particles was done on gravity collected material. Samples of entrained dust were collected through the use of cascade impactors. Both samples were analyzed for size distribution and particle shape. Using the simulated coal cutter permitted variation of operating and in-situ parameters to provide information on the effects on generation of -400 mesh particles. In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.1 cm x 15.2 cm) were first subjected to confining pressures, equivalent to in-situ conditions. Such blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with an attached camera.

Jan 1, 1985

By W. J. Nelson

Detailed underground geologic map- ping at a scale of 1:1200 has been carried out at the Crown II Mine of Freeman United Coal Mining Company, which operates in the Herrin (No. 6) Coal Member. The roof sequence, upward from the coal, includes (1) soft, medium- to dark-gray shale; (2) hard, black, fissile shale; (3) argillaceous nodular-bedded limestone, and (4) fine-grained, shaly, water-bearing sandstone. The first unit is highly lenticular, and any or all may be missing at a given locality. The sand- stone has a sheet facies and a channel facies. The Herrin Coal is eroded in channels near the Crown II Mine. Structural features mapped at Crown II include normal and strike-slip faults of small displacement, "slips" and clay dikes, and limestone "bosses." Less stable roof and wet con- ditions are encountered where the limestone is thin or missing or where it is broken by natural fractures or by artificial openings that inter- sect the water-bearing strata above the limestone. Geologic mapping of the underground workings has allowed us to predict faults, fracture zones, and channels ahead of the face for this mine. Some lithologic and structural patterns apparently are random and cannot now be projected. Conventional exploratory drilling is entirely inadequate to map faults or lithology of the roof, but it does indicate the range of lithologic variability, which can be used to project needs for roof sup- ports. Drilling also is useful In locating channels and in mapping regional variation in thickness and facies of the sandstone.

Jan 1, 1980

By D. Christofferson

As an alternative power source to eliminate trailing cables, ESD Corporation is installing a flywheel system on a shuttle car. Flywheel power is extracted by a high-speed generator, developed by Lear Siegler Corp,, and the system -- including vacuum and lubrication and cooling auxiliaries -- is supplied by the aerospace group, Rocketdyne Division of Rockwell International. The flywheel system is being developed under a three-year contract with the Department of Energy. It is a follow-up contract to a previous DOE-contracted study by General Electric Co. in which it was shown that a flywheel can be a feasible power source for a shuttle car from technical, economic, and safety standpoints. This paper addresses the status of the program, design decisions established, and plans for laboratory test procedures and underground demonstration. The flywheel-powered shuttle car is a conventional 6-ton capacity shuttle car equipped with a 7-rotor flywheel energy storage package. The energy package is the sole source of power for the shuttle car through a complete mission duty cycle (MDC) of tramming to the miner, receiving a load of coal, and returning to the secondary haulage system. Energy stored in the system exceeds MDC requirements and waiting times to provide an ample margin of reserve energy. The energy storage system is recharged by spinning the rotors back up to maximum speed each time the shuttle car comes back to the secondary haulage system. The electrical charge motor is connected to a power source to recharge the system while the load of coal is being discharged.

Jan 1, 1982

By D. Christofferson

As an alternative power source to eliminate trailing cables, ESD Corporation is installing a flywheel system on a shuttle car. Flywheel power is extracted by a high-speed generator, developed by Lear Siegler Corp., and the system -- including vacuum and lubrication and cooling auxiliaries -- is supplied by the aerospace group, Rocketdyne Division of Rockwell International. The flywheel system is being developed under a three-year contract with the Department of Energy. It is a follow-up contract to a previous DOE-contracted study by General Electric Co. in which it was shown that a flywheel can be a feasible power source for a shuttle car from technical, economic, and safety standpoints. This paper addresses the status of the program, design decisions established, and plans for laboratory test procedures and underground demonstration. The flywheel-powered shuttle car is a conventional 6-ton capacity shuttle car equipped with a 7-rotor flywheel energy storage package. The energy package is the sole source of power for the shuttle car through a complete mission duty cycle (MDC) of tramming to the miner, receiving a load of coal, and returning to the secondary haulage system. Energy stored in the system exceeds MDC requirements and waiting times to provide an ample margin of reserve energy. The energy storage system is recharged by spinning the rotors back up to maximum speed each time the shuttle car comes back to the seconaary haulage system. The electrical charge motor is connected to a power source to recharge the system while the load of coal is being discharged.

Jan 1, 1981

By Alvin Kaufman

Malthus, an eighteenth century economist, predicted a rather dismal future for the world. It was his contention food supplies would not be sufficient for the population of the world because the economy of a nation grew arithmetically while population increased geometrically. As a consequence, within a relatively few years mass famine would spread throughout the world. This prophecy, based on an agrarian economic situation, did not come true at least insofar as the Western World was concerned. In largo measure, the salvation of our part of the earth resulted from the growth engendered by the Industrial Revolution. Throughout much of today's world, however, the Malthusian theory seems to be coming true. The advantages and benefits of the Industrial Revolution have net reached all nations. Further, the situation has been compounded by the benefits of modern medicine. This has reduced child mortality and extended life expectancy, but placed no limitations on births in the developed countries, child mortality has declined to 2 percent and adult life expectancy has doubled, but education and general prosperity have resulted in voluntary limitations on pregnancies thus partly offsetting the increased chance of survivals Even so, the present rate of population increase in Europe is approximately 6 percent per decade, and somewhat higher in the U.S., Japan, and other developed countries. The world as a whole, however, is expected to double its population by the year 2000, This would imply a rate of increase in the less developed countries approximately four times that in Europe.

Jan 1, 1966

By T. M. Klemetti, T. J. Batchler, T. Matthews

From 2013–2017, there were over 1,120 documented injuries, including fourteen fatalities, from ground falls in underground mines in the United States (MSHA 2017). The majority of these ground-fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely used in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded-wire screen as used in underground coal mines by conducting a laboratory testing program using the Mine Roof Simulator (MRS) in NIOSH’s Bruceton Research Center Laboratory in Pittsburgh, PA. The load-displacement characteristics of an 8-ft x 12-ft area of 8-gauge welded-wire screen were evaluated using a test frame designed for testing multiple load-pull locations. In previous tests, load-pull contact was always in the center of the bolted screen section. In this study, larger pull contact areas are used to simulate roof falls. The information obtained in this and similar studies can be used to better understand the loading behavior and surface control capability of roof screen in underground mines. INTRODUCTION AND BACKGROUND The large majority of ground-fall injuries are caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Compton et al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded-wire screen as used in underground coal mines by conducting a laboratory testing program in the Mine Roof Simulator (MRS) in NIOSH’s Bruceton Research Center Laboratory in Pittsburgh, PA. Previous tests to evaluate the performance characteristics of various types of screen have been conducted by the University of Alberta (Tannant, 2001). In this study, the load-displacement properties of welded-wire, chain-link, and expanded-metal mesh were measured by performing full-scale pull tests. A flat steel plate was pulled through a screen test sample that was bolted to a special test frame while the pulling force and mesh displacement were measured. These tests established the general load-displacement behavior of the screen. Peak load capacities and stiffness were determined for each screen type, showing how welded-wire mesh has a much stiffer initial loading response, whereas chain-link and expanded-metal mesh have large displacement capabilities and exhibit significant post-peak ductility.

Jan 1, 2019

By Hsu-Hui Hsing

In several previous studies from this laboratory (1-4) the autophobicity concept of Zisman and co-workers (5, 6) has been extended to gas phase adsorption processes. Low molecular weight alcohols adsorb on silica or alumina to yield novel isotherms in that monolayer adsorption occurs at low relative pressures indicative of strong bonding, but subsequently multilayer adsorption is quite sparse and diminishes with molecular weight of the alcohol. Such isotherms fit no standard classification scheme, however, in the vacinity of monolayer coverage alcohol isotherms give an excellent fit to the Langmuir or B. E. T. , Type I model (7). Monolayer adsorption is relatively irreversible and it is thus possible to prepare these chemisorbed layers and perform subsequent adsorption studies thereon. All indications are that the adsorptive properties on such films is radically different from that on the underlying alumina (4, 8) and in one study finite contact angles for hydrocarbon fluids were observed. One perennial conceptual difficulty is that there is no observed upper bound to the adsorption isotherm which would be necessary for autophobic adsorption to occur. The cause for this has been studied, and it is currently believed that adsorption is complicated by reversible capillary condensation at contact points between powder particles. The evidence for this is that large particle powders give less "apparent" adsorption at high relative pressures and in one very tedious study adsorption on planar sheets, oxidized aluminum displayed similar reduced uptake at high relative pressures when compared with high specific surface area powders (3).

Jan 1, 1974

By Brenda B. Mehnert

Long-term monitoring is necessary to successfully develop predictive subsidence models. Thus, the Illinois Mine Subsidence Research Program (IMSRP) has documented subsidence over a longwall mine in south-central Illinois throughout a 3-year period. No monitoring results of this duration have been previously published for longwall mining in Illinois. To study the effects of surface subsidence and the rate of subsidence, precise level surveying was conducted at the site two or three times a year. Level surveys were conducted at approximately the same time of year using a WILD NA-2 level with a micrometer. Second-Order, Class-I, closure errors were obtained in each survey. Survey monuments were designed to minimize frost-induced movements. At this particular site in southern Illinois, subsidence over chain pillars and the panel centerline continued 3 years after mining. Since mining in 1988, 6.67 feet of subsidence or 70% of the extracted height has been documented over the panel centerline, with almost 0.30 feet in the last two years. The area over the chain pillars has subsided a total of 1.44 feet, with 0.44 feet occurring within the last 2 years. Monitoring over the chain pillars and at the centerline shows the residual subsidence to be fairly uniform. Monitoring is continuing over both of these areas. Long-term monitoring data can be used to improve evaluation of subsidence effects on land and structures. However, coal companies will time mitigation activities depending on other factors including the threshold of structural damage, type of repair needed, and maintenance of landowner and company relations.

Jan 1, 1986

By Mogens Henriksen

In the past decade, numerous urge scale drilling projects have made use of reverse circulation air lift methods. Reverse air lift pumping can be established by injecting gas into a column of liquid; the subsequently decreased density of the gas-liquid mixture allows atmospheric pressure outside the lift conduit to establish flow. The rate of flow can be controlled by varying the gas to liquid ratio. A typical reverse circulation air lift system is depicted in Figure 1. Allen1 has described a number of reverse air lift drilling projects. Although cited examples are generally related to large diameter holes, the method has seen use in other applications such as sand dredging, chemical pumping, water well pumping and continuous coring. One particular benefit obtained with enclosed reverse circulation drilling is elimination of lost circulation. The required air/water ratio for pumping at a given submergence and lift has been established experimentally by Gibbs2. His data, however, do not reflect sensitivity of flowrate to air/water ratio. Further, in Gibbs' work, air apparently is injected continuously along the column of water. This configuration differs from that used in reverse air lift drilling where air is injected at discrete points only. Gas lift theory has received considerable attention over the past decades. Orldszewski3 defined flow regimes in two phase flow. Griffith and Wallis4 determined relative velocities of gas to liquid. Two-phase flow has been studied extensively for oil transport in inclined and vertical pipes by Chierici et a15, Beggs and Brill6, and Gould, Tek and Katz.7

Jan 1, 1977

By H. Soto

As a follow-up to a laboratory study, a pilot scale column for the flotation of coarse particles was designed and then tested in two different applications. In the first test, the concentration of a coarse phosphate ore (normally beneficiated by skin flotation in spirals) was carried out in a flotation plant in Florida. In the second pilot test, the column was used as a scavenger cell in the coarse flotation section of a potash beneficiation plant in Saskatchewan, Canada. Particle size of the phosphate feed was of the order of 0.6-1.0 mm and the potash feed 1-3 mm. The column was 1 feet diameter and was fed at rates between 0.5 to 1.4 tph. The effect of operating variables such as air and water flow rates, bubble size, frother concentration, residence time, sparger, etc were evaluated. The most important factors in column performance were found to be bubble size, air flow rate and the thickness of the froth bed. Best results were obtained in the absence of a froth bed, with low air flow rates and with small bubbles. The paper presents comparative performance and discusses details of the column design. Phosphate recoveries in the column were better than 90% whereas the conventional skin flotation circuit normally yields about 60% recovery for a comparable concentrate grade. Potash recovery from the tailings of the conventional flotation circuit was as high as 42% recovery. Particle size distribution of the potash concentrate was coarse enough to meet requirements for potash fertilizer.

Jan 1, 1993

By Maria S. Adusmilli, Bhaskara A. Rao, Jorge G. C. Barros, Augusto F. Mendonca

Lateritic gold has been the object of study only for a very few years, though nuggets have been mentioned in earlier works even as early as 1984 by Hartt in Brazil. In Mato Grosso State, lateritisation is intense, as is common in all tropical forest areas of the world. Exploration has revealed the presence of recoverable "nugget gold" of variable sizes (30 - 200 gms) but frequently of good size (0 - 40 gms), especially near Cuiaba and Alta Floresta regions. In both of them the host system is a lateritised breccia indicative of a fault or shear zone breccia, though in different lithological domains. The Cuiaba occurrences are phyllitic and show a profile as follows, from top to bottom: 1) Compact ferralite crust. 2) Oolitic to pisolitic compact crust (+ some gold). 3) Mottled concretionary laterite crust. 4) Lateritised "eluvial material" (gold nuggets). 5) Mottled patchy to banded laterite. 6) Banded lateritised phyllite with lenticular to banded goethite. 7) Altered red goethitic phyllite, with quartz veins (+ fine gold). 8) Unaltered grey phyllite with quartz veins (Protore). The Alta Floresta-Juruena River occurrences are volcano-sedimentary and show a profile as follows: 1) Deep brown siltitic, argillaceous and arenaceous material with organic matter (+ gold). 2) Modular and concretionary laterite, compact and indurated, with arsenophyrite in quartz fragments (gold nuggets). 3) Band with silty-clayey matrix and arenaceous in nature. 4) Bedrock meta-arcosian arenite. 5) Volcano-sedimentary with rhyodacites and andesitic basalts, with intercalations of arkosic and greywacke nature. Breccias and quartz veins, and granites associated in different portions (Protore).

Jan 1, 1988

By R. C. Timberlake

In the past three years there has been a great amount of attention given to phosphates world wide, and in particular to the Florida Phosphate Industry. I would like to relate some of the most recent history of the industry and give you a personal outlook for the future. Phosphate rock has been produced in Florida since its discovery on the Peace River in the 1880's. Through 1976, approximately 720 million ST of rock had been mined from Florida reserves, and it is my opinion that there are at least 1.2 billion tons remaining which are consolidated, accessible and can reasonably be expected to be permitted for mining. Over half the 1.2 billion tons will be deeper, more scattered, leaner and will produce lower grade rock than the Bone Valley of Central Florida has tradition-ally produced. In 1973, '74, '75 and '76 the Florida Phosphate Industry produced 32.6, 34.0, 38.2 and (38.0) (P) million ST of phosphate rock respectively. This rock was produced by ten mining companies, Agrico, Borden, Brewster Phosphates, Gardinier, Grace, IMC, Mobil, Occidental, Swift, and USS Agri-Chem; mines are located -17 in Polk County, one in Hillsborough County and two in Hamilton County, Florida. Phosphate rock is used by local companies in Florida primarily to produce phosphoric acid from which DAP and TSP is manufactured. Florida acid producers use about 15 million STPY in acid plants in Florida, and another 7.5 million STPY is consumed by acid producers in plants on and near the Mississippi River. Somewhat

Jan 1, 1977

By George E. Peacock

Campbell Red Lake Mine is situated at Balmertown, in the Red Lake District of Northwestern Ontario, Canada. This area is some 120 miles north of the Trans Canada Highway and is some 160 miles Northeast of Winnipeg, Manitoba. The majority of our 300 employees live in Balmertown, which is a community of some 1,200 people, situated adjacent to the mine proper. The mine is serviced by a single shaft 4,300 feet deep. There are 27 levels at 150 ft. intervals. Stoping is being carried out down to the 20th level with only preliminary development having been done on the bottom 6 levels. The majority of our mill feed of 825 tons per calendar day comes from above the 10th level. Gold occurs as specks and streaks in bluish-grey to white quartz carbonate veins. It is extremely fine grained and most is invisible to the unaided eye. In addition to Gold the veins carry varying amounts of sulphides such as, Arsenopyrite, Stibnite, Pyrite, Pyrrhotite and Sphalerite. A minor amount of silver occurs as an impurity in the gold. Arsenopyrite is a marker for the gold ore at Campbell. The average grade of the mill feed is 0.7 oz. of gold per ton. The ore is dumped into an underground ore pass that feeds to a jaw crusher on the 20th level that reduces the rock to a maximum size of 4". This material is hoisted by skips to an ore bin in the head frame.

Jan 1, 1975

By Joseph J. Garbarino

World demand for phosphate fertilizers has grown at an average annual rate of between 6 and 7 per cent over the past 10 years. In the next five years world demand is expected to at least continue to grow at that rate. Also, the continued need for improved fertilizer materials, coupled with improvements in fertilizer technology, have placed added importance on the use of phosphoric acid as a starting material for high analysis phosphate fertilizers. This demand for phosphates and phosphoric acid must be met by increased production. Increased phosphoric acid production also brings increased demand for chemical processing agents including foam control agents. We at Arizona Chemical Company have closely followed the phosphate fertilizer industries needs. Arizona Chemical Company has been an important supplier of flotation agents to the phosphate industry, primarily from its Panama City, Florida plant. We have also recognized the important role played by foam control agents in the wet-phosphoric acid manufacturing process. We feel it is the responsibility of the supplier of foam control agents to offer specifically designed products that are highly efficient and economically useful. The difficulties involved in evaluating foam control agents in the plant are recognized. Owing to the large number of variables present, and the difficulties in controlling these variables during the period of a plant trial, plant evaluation of a large number of foam control agents is impractical. We have attempted to develop a practical, reproducible, and yet rapid, laboratory evaluation test which correlates with plant performance.

Jan 1, 1966