Search Documents

There are presently in use many grinding mill control schemes and concepts. This paper presents one operating method of controlling the particle size of the cyclone overflows for proper metallurgical results and controlling the level of the cyclone feed sump and new feed rate to obtain lowest unit cost of finished (ground) material which is usually at the maximum grinding mill throughput. This system stresses simplicity of field instrumentation and control strategy. Both of these factors lead to better operator understanding and acceptance. The low capital investment of this system also makes it more attractive at the Buick Concentrator when compared to other more complicated systems utilizing mass flow measurement and a computer to calculate circulating load and infer particle size. Furthermore, it has the advantage of utilizing an actual measurement for control, rather than a difficult-to-maintain inferred value. There are several reasons for maximizing mill throughput at Buick. The milling rate before automatic control was too low when compared to mill throughput increases planned for the future. Through this new operating system, it appears Buick will not have to make major changes of mill motors and speeds to meet the increased? production rate. Also, since power costs continue to escalate, it is desirable to maximize the throughput to the grinding circuit and reduce overgrinding to achieve a reduction in power cost per ton of ore milled. Presently, 45% of the concentrators' total power is consumed in this grinding circuit.

Jan 1, 1977

By Fun-Den Wang

In underground coal mines, three types of roof failure (2)*, tensile, local, and shear, occur in the development entries and in room-and-pillar extraction areas. Most of the tensile failures in the roof at the center of the mine opening as well as those local failures due to fracture or jointing can be controlled by roof bolts, trusses, and timbering. However, control of the shear failure at the sides of the roof (or the cutter-roof caving) has not been successful with ordinary roof control methods. The only effective method, when there is an indication of cutter-roof caving, is to use cribs, which are costly and make transportation, ventilation, and production difficult. Frequently, the operator allows the cutter roof to cave and then cleans it up rather than trying to stop it. This shear type of roof failure is often associated with large areas which may progressively involve several hundred feet of roof caving at one occurrence. At times, this shear failure occurs suddenly with little or no warning. This can result in buried equipment and great danger to the safety of personnel. This shear failure may be due to one or more of the following: high stress concentrations at the corner of the roof from (1) high horizontal to vertical load ratio, (2) orthotropic elastic properties of rock and coal, (3) greater stiffness of the immediate roof layer than of the secondary roof layer, (4) viscoelastic behavior of rock and coal, and (5) geometry and material properties of the geologic setting. Removing or reducing the high stress concentration should improve the roof stability. The structural analyses of models of two typical

Jan 1, 1972

By Frederick P. Agterberg

It can be useful to model the mean grade values for a metal in mineral deposits containing that metal as representing the extreme value tail of a lognormal frequency distribution for the concentration values of the metal in rocks of all types. Results for copper and zinc in the Abitibi area of the Canadian Shield are compared to results previously obtained for the Canadian Appalachian Region. The lognormal model is also applied to a set of 162 large gold deposits in the Abitibi area. In the second part of the paper, 1311 large and small gold deposits in the Abitibi area are modelled as discrete events. By means of a newly developed spatial clustering model it is possible to predict the variances of random variables for frequencies of deposits in cells of different sizes.

Jan 1, 1979

By Barry Hunsaker

I cannot help but be reminded, as I stand here today, of my boyhood years and heritage, both of which are inextricably tied to this very valley and are, in a: bay, apropos of the theme of this Keynote Session. I remember the scarcity of people. For example, 48, 000 in Phoenix and 436, 000 in the State in 1930 and 65,000 in Phoenix and 499, 000 in the State in 1940. Today Phoenix boasts a population of over 500, 000 and the State a population of 1, 500,000. I remember the' lack of facilities, goods and services, including gas and electric power. I recall stories of my grandfather who had the freighting or teaming contract to haul all the supplies and generating equipment, by wagon mind you, up the old Apache Trail to Roosevelt Dam. . .a three day trip from the nearest railhead which, by the way, was not Phoenix, for it did not merit a railhead on those days, but the village of Maricopa approximately 25 miles south of Phoenix. I remember chopping firewood, heating wash water on an open fire in a No. 3 wash tub at the rear of the house and doing my school homework by the light of a kerosene lamp just 25 to 35 years ago within what is now a large metropolitan area

Jan 1, 1965

By R. L. Godfrey

The Custom Coals advanced coal cleaning plant will be designed with a unique blending of existing and new processes to produce two types of compliance coals: Carefree Coal? and Self-Scrubbing Coal?. Carefree Coal will be produced by cleaning the coal in a proprietary dense media cyclone circuit utilizing fine magnetite to remove up to 90 percent of the pyritic sulfur and correspondingly greatly reduce the ash. While may utilities can achieve full S02 reduction compliance with Carefree Coal, others face higher sulfur reduction requirements due to the higher sulfur content of their existing fuel supplies. For these circumstances, a patented Self-Scrubbing Coal will be produced by taking Carefree Coal and pelletizing limestone-based additives with the finest fraction of the clean coal. These technologies will enable over 150 billion tons of non-compliance U.S. coal reserves to meet compliance requirements.

Jan 1, 1995

By T. A. E. Breen

A new high intensity grinding technology has been developed and is now being commercialized by Hicom International of Australia. This has led to the development and manufacture of Hicom 120 grinding mills which are now being sold internationally for a range of mining industry applications. The first commercial process application has been for the diamond sector, where the ability of the mill to remove host kimberlite rock by attritioning, with no damage to the thereby liberated diamonds, is seen to be a most beneficial attribute. There are, however, many other mineral industry applications for this mill.

Jan 1, 1999

By Robin Dill, Wei Song, Andrew Perham, Leo Martin

"AECOM completed a subsurface exploration program for an 18-foot diameter, approximately 4-mile long rock tunnel project in Hartford, CT. The tunnel crosses the regional geologic trend through the middle of a sedimentary basin, passing through four separate rock formations, including two volcanic flows. Faulting is prevalent, with at least 15 faults encountered during the site investigation. Severe artesian flows were also experienced in several of the borings, requiring highly specialized drilling equipment. Sixty-two borings and associated testing were performed to characterize the structural geology, hydrogeology, rock properties and ground conditions. A phased program was carefully planned and implemented with participation of geotechnical and geologic specialists, with thoughtful evaluation along the way to react to the ground conditions encountered, and make appropriate refinements. This paper will discuss the subsurface program details; the integrated efforts used to effectively characterize the ground; and will summarize the final characterization presented in the GBR. PROJECT DESCRIPTION The South Tunnel Conveyance and Storage Tunnel project is part of the Metropolitan District (MDC’s) Long Term Control Plan to address discharges to various water bodies throughout the greater Hartford area. This program includes a main conveyance and storage tunnel; a tunnel boring machine (TBM) launch shaft and retrieval shaft; adit tunnels with associated drop shafts and connection structures; consolidation conduits and manholes; and a tunnel pump station (TPS) at the downstream end of the main conveyance tunnel. AECOM is serving as prime designer for the MDC on this project. The main conveyance tunnel (hereinafter referred to as the “South Tunnel”) will be a deep rock tunnel with an invert depth of approximately 180 feet at its downstream end and approximately 218 feet at the TBM retrieval shaft. The tunnel will have a finished diameter of 18 feet. The tunnel will rise in grade at a slope of 0.1 percent to its upstream end. Total invert depth along the deep tunnel alignment ranges from about 180 ft. to as high as 320 feet. The total length of the tunnel will be 21,754 feet. The South Tunnel will be constructed using a shielded TBM and fully lined with pre-cast concrete segments."

Jan 1, 2016

By M. D. Bishop

Early solvent extraction circuits in the uranium industry utilized bona fide kerosenes as diluents for extractant chemicals. These kerosenes were used successfully in the uranium industry; however, at least one plant was destroyed by fire resulting from the use of a low flash point kerosene. Although the term "kerosene" is used throughout the solvent extraction industry, the authors have been unable to find any use of kerosene in copper solvent extraction circuits. A term that is occasionally used with reference to diluents is "metallurgical kerosene." Such a term is unrecognizable in the petroleum industry. Kerosene [or kerosine] is a flammable hydrocarbon mixture that is less volatile than gasoline. It is produced for combustion purposes and may have variable compositions of organic compounds including alkanes, alkenes, alkines, and aromatics. Diluents are constant composition hydrocarbon mixtures developed specifically for use in solvent extraction processes. These products usually have much lower vapor pressures and higher flash points than kerosene. In solvent extraction systems, they typically comprise 70 to 95 v/o percent of the circuit organic. The primary purpose of the diluent is to adjust the extractant concentration to the working range of the operation. The diluent and extractant must be completely soluble or miscible with each other. Secondary diluent effects are to promote transfer kinetics, optimize phase disengagement, and minimize both organic in aqueous and aqueous in organic entrainment.

Jan 1, 1996

By N. B. Aughenbaugh

Compacted clays are used as permeability barriers in many mineral engineering projects such as heap leaching, containment ponds, tailings disposal and earth dams. Source materials used for clay liners include a wide variety of sand, silt and clay admixtures that exhibit dramatically different engineering properties when densified. The permeability and plastic properties of fine-grained soils are reviewed with respect to the state of compaction as the water content varies. Be-cause they are weak in tension, compacted clays are susceptible to cracking when subjected to differential flexural movements. Designs of compacted clay liners must include an evaluation of their flexibility which is the ability of a fine-grain soil to bend plastically without cracking. This paper will also discuss the importance of flexibility with respect to soil types, compaction effort, failure mechanism and testing evaluation to the performance of clay liners in preventing seepage of pollutants from a containment site.

Jan 1, 1990

The evaluation of Abandoned Mined Lands can involve the investigation of very large areas of land. Often, the locations of critical areas or impending problems are unknown, and are not easily identified from the surface. Microseismic monitoring has been demonstrated to be effective in identifying potential instabilities and active movement in mines from distances of several kilometers. By placing sensors in proximity to, or in contact with, a high acoustic conductance layer close to the mined zone, large areas can be monitored for potential problems with a minimum of sensors and drillholes. As part of a U.S. Bureau of Mines contract, a prototype system was developed to identify and locate potential instability problems over wide areas of land. Once a problem area has been located, the system can be used to analyze the type of the problem, its size, relative degree of instability, and potential for damage. Continued monitoring after application of remedial measures can effectively determine the efficacy of those measures.

Jan 1, 1993

By R. K. Singhal

In an underground coal mining environment, a frictional ignition may be defined as the ignition of an explosive air/ methane/coal dust mixture by mining machinery. As the use of power loading equipment has become more widespread, frictional ignition incidents have increased. There have been many fatalities and injuries from this cause including the death of eleven miners in Sydney coalfield of Nova Scotia, Canada in 1979. This paper reports on the findings of a preliminary study carried out under the auspices of the Coal Research Laboratories, Department of Energy, Mines and Resources Canada. The objective of this study has been to identify a Longwall face cutting system that is inherently safer than the conventional shearer loaders used in Nova Scotia.

Jan 1, 1985

By T. Krumins, L. Zunti, R. Frischmuth

"Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals and other process piping. In the autoclave vent application, titanium ignition risk is controlled by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature operating conditions and therefore oxygen concentration and the associated titanium ignition risk is dependent on standard operating procedures, process control interlocks and permissive conditions. It is not uncommon for these standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for a titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions. INTRODUCTION High temperature pressure oxidation (>190°C) is a well recognized and versatile metallurgical oxidative pre-treatment process commonly used to liberate gold from refractory sulphide ores and concentrates before conventional leaching with cyanide. Titanium and titanium alloys are highly corrosion resistant in pressure oxidation process conditions and are therefore commonly selected as materials of construction for many components including: autoclave internals, agitators, process piping, and components in autoclave vent systems. Operations that anticipate or have experienced aggressive corrosion in the vent system often have little choice in material selection other than the use of titanium (Krag & Henson, 1992). Titanium is not suitable for use with elevated oxygen concentrations and is considered a restricted material because of its high pyrophoricity and combustion propagation properties (Beeson, Smith, Stewart, 2007). Several serious incidents have occurred in which titanium materials have ignited in autoclave applications (Zawierucha, McIllroy, Million, 1995). In autoclave vent applications, titanium ignition risk is reduced by preventing elevated oxygen concentrations, maintaining low gas velocities, and minimizing the potential for gas impingement on surfaces. Oxygen concentration in the autoclave vapour phase and vent system is dependent on the autoclave operating pressure and temperature conditions and therefore titanium ignition prevention controls typically include process interlocks and operating procedures based on the selected nominal design operating conditions. However, it is not uncommon for these controls to be deficient or for operations to deviate from the nominal operating conditions over time, increasing the risk of titanium ignition. The introduction of an online calculation of autoclave overpressure and a maximum target autoclave pressure as well as associated process control interlocks and permissive conditions can alert the autoclave control room operator and prevent an elevated oxygen concentration from developing, and therefore reduce titanium ignition risk in autoclave vent systems."

Jan 1, 2016

By Leo R. Love

A comprehensive study of the environmental conditions of the area affected by the Colfax and Cheswick Power Stations is of extreme importance to Duquesne Light Company. The residents in the valley where the two plants are located have complained for many years about the emissions from the Colfax Plant which is of the 1920 to 1930 vintage and which has a capability of generating approxi¬mately 200 Mw. They were extremely happy to hear that the Company had plans for shutting it down, however, they were extremely unhappy to hear that we were planning to build another even larger one to take its place in the same vicinity, namely the Cheswick Plant with a capability of 570 Mw. They had visions of a plant twice the size of the Colfax Plant and belching out twice as much smoke. A few of the citizens from that area were most vehement at the public hearings that were held by the Allegheny County Air Pollution Bureau for obtaining an installation permit. With two power plants already existing in that area (Duquesne Light Company's Colfax Plant and West Penn Power's Springdale Plant), the primary concern of the Allegheny County Air Pollution Control Bureau was that the Cheswick Station might increase air pollution levels beyond what they considered to be dangerous limits. It became very evident that the Allegheny County Air Pollution Control Bureau would be extremely reluctant to grant installation and operating permits unless they were satisfied that the new plant would not increase local pollution levels and that we were taking sufficient steps to monitor the emissions from our plants and also the ambient air in the general area. We concluded that an extensive air pollution monitoring program must be conducted in the area to determine the effects of the operation of our plants. The program was conceived with our consultants, NUS Corporation of Rockville, Maryland, and was begun in June, 1968. It was designed to accomplish several things: 1. Determine the effect on the ambient air of the operation of each of

Jan 1, 1972

By A. Cecala, J. Noll, J. Organiscak

Many underground metal/nonmetal mines are using enclosed cabs on mining equipment to reduce the exposure of miners to diesel particulate matter (DPM). However, some enclosed cab systems may not be meeting their expected efficiency in capturing DPM, which could be a result of inappropriate filter use, cab leaks or insufficient pressurization. NIOSH investigated several types of filters for reducing DPM to determine which type had the best capture efficiency. The laboratory results indicated that a MERV 8 (minimum efficiency reporting value, as defined by the American Society of Heating, Refrigerating and Air- Conditioning Engineers) filter captured about 50% of the DPM, a MERV 16 filter collected 96-98% of the DPM and two HEPA (high efficiency particulate air) grade filters captured over 99% of the DPM. NIOSH also performed a field study to measure the efficiency of two cabs at a limestone mine. The cab filtration systems of a loader and haul truck were found to be over 90% effective in removing DPM, except under certain operating conditions when the efficiency was as low as 41%. A possible reason for the low efficiencies is an open window in the cab, but more studies need performed to obtain a better understanding of the cause and solution of the problem.

Jan 1, 2011

By P. Jonsén

Understanding mill charge motion is important. In the charge, the centre of gravity is shifted from the rotational centre of the mill system, and its motion is induced by rotation of the mill, while at the same time the charge creates a torque into the mill system. Breakage of ore particles and wear of liners/ball media are closely linked to the motion. To study these phenomena in a physically correct manner, numerical models for different parts of the mill system are needed. Validations of such models are scarce, because of the difficulty to measure in a tumbling mill. Experimental measurements in a lab mill were done for diverse load cases: varying feed materials, mill fillings, mill speeds and pulp liquids. The mill is set up to directly measure the charge-induced torque. The accuracy is good with relative uncertainty smaller than ±2% for relevant load cases. A full three dimensional numerical model of the whole mill is used to predict induced torque. Agreement between predicted and measured torque at steady-state is good. In addition, the model can accurately predict the mill start-up behavior for torque and mill power. This proves that the model is physically correct, and can be used for full-scale mills.

Feb 27, 2013

By C. C. Harvey

As we move towards the 21st Century there are several factors that will influence the markets and processing requirements for industrial minerals. Traditional markets for many industrial minerals in the developed world are frequently stagnant or decreasing because of their maturity or due to environmental factors such as reclamation, recovery of byproducts, and recycling. Some industrial minerals are greatly affected by these factors, while others are either immune to or have adapted successfully to meet these challenges. In the developing countries of the world, there is rapid market growth and resource exploitation. The future of specific mineral commodities in several markets will be discussed.

Jan 1, 1997

By Bo Hyun Kim, Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health have tested the finite element code, UT3PC, with LaModel to evaluate their results using know case studies. The purpose of the testing was to demonstrate the usefulness and limitations of these programs in evaluating mine layout design. Both of these software packages are simple to use and free for public download. Their use by mine engineers, along with other tools, such as empirical methods, can enhance the assessment of a mine layout design. LaModel can model mining layout on a mine scale or, at least, on a multiple-panel scale. However, this software has limitations in calibrating to conditions at many coal mines in the western United States. The UT3PC software models smaller parts of a mine and is used to evaluate the design of pillars, shafts, or drifts; but the software calculates all components of the stress tensor and provides stresses, displacements, and safety factors throughout the model volume. The two codes are used to evaluate design of one known case, and UT3PC is used to evaluate another case. The results and approaches demonstrated in the testing are intended to aid mine engineers in evaluating site-specific problems and to show that these tools can provide useful information to the mine engineer in evaluating mine layout design.

Jul 1, 2023

By Christian F. Baiz

A new agenda has risen. Born out of governments' policies and world economies, the years ahead will carry with them reduced growth. For inflation dependent and capital intensive industries, such as metals and mining, as well as most other natural resource industries, a period of long-term contraction in outmoded and costly capacity will evolve. This will be supplanted by new, lower cost capacity in some cases, but only if the total cost of production, including cash operating and debt service costs comes in at or below current market conditions. The industrial outlook can be characterized as bearish. As one major U.S. bank economist put it, mining companies planning their five-year forecast from 1984 out, should take the current market conditions and straight-line them to the end of the decade. With low growth and low inflation, the real price of metals will remain flat or slightly declining. As a result, capital funding will be problematic. The low cost producer, that is one with low cash costs and low principal and interest costs per unit of production, will succeed.

Jan 1, 1984

By Ali Yalçin

The study area is located in the NW of Uluborlu (Isparta). Massive limestones and alluvial deposits form the lithological units of the study area. The average thickness of the alluvium deposit consisting mainly of light brown - red colored and fine grained clastic sediments which derived from the limestone is about 10 meters. The aim of this study to investigate the uses of this alluvial sediments as tile - brick material. For this aim, disturbed and undisturbed samples have been taken from different depths in the alluvial deposits. Mineralogical compositions have been determined by XRD and major oxide contents by XRF. Laboratory experiments have been carried out to determine the technological properties of the samples. The selected major oxide contents of samples vary between A12O3 (24.6 - 24.12 wt %), CaO (0.76 - 4.27 wt %), Fe2O3 (10.21 - 10.29 wt %), MgO2 (1.25 - 1.51 wt %). CaCO3 and MgCO3 values calculated from the geochemical analyses, are between 1.55 - 1.62 and 2.62 - 3.17 respectively. The ratios of grain size of the samples are 82 % for < 0.2 mm and 5 % for > 3 mm. Geochemical analyses and technological features of the samples indicate that these fine grained sediments of alluvial deposit are suitable in terms of uses as tile - brick material. The potential reserve of this tile - brick material has been determined as 40 million tones.

Jan 1, 2005

By K. A. Natarajan, K. Karthiga Devi

"A biodegradable flocculant was produced during growth of Bacillus megaterium. The major component of the bioflocculant was found to be a polysaccharide composed of some proteins. Fourier transform infrared (FTIR) spectra analysis revealed the presence of carboxyl and hydroxyl groups in the bioflocculant, and thermal characterization by differential scanning calorimetry (DSC) showed the transition and crystalline melting point at 90-105°C. The effects of bioflocculant dosage and pH on the flocculation of mineral suspensions were evaluated. The bioflocculant exhibited good flocculating capability on mineral suspensions and achieved flocculating efficiencies of 90 percent for kaolinite and 85 percent for hematite suspensions at a dosage of only 5 mL/L. The maximum arsenite removal was found to be 90 percent at a bioflocculant dosage of 2 g/L, which is better than traditional chemical flocculants. This study demonstrates that microbial bioflocculants have potential for application in environmental cleanup, such as in the flocculation of mineral fines and in the remediation of solutions that contain toxic heavy metals.IntroductionBioflocculants are biopolymers produced by microorganisms during their growths. The predominant components of a bioflocculant are extracellular polymeric substances such as glycoprotein, protein, cellulose and nucleic acid (Salehizadeh and Shojaosadati, 2001). Bioflocculants have gained much wider attention due to their biodegradability and safety. In recent years, the study of bioflocculants has attracted wide attention. Bioflocculants can be nontoxic, harmless and eco-friendly. Normally, they exhibit different functional properties, serving as stabilizer, dispersant or thickener. Among these properties, flocculation is of major interest. For example, Phormidium sp. strain J-1, isolated from a drainage channel, exhibited excellent flocculation activity for bentonite particles in liquid suspension (Fattom and Shilo, 1984). A protein bioflocculant produced by Rhodococcus erythropolis could efficiently flocculate suspended solids while losing their flocculating activity by enzymatic digestion (Kurane et al., 1994, Takeda et al., 1991). Klebsiella sp. strain S11 screened from activated sludge was unable to flocculate without the addition of calcium chloride (Dermlim et al., 1999)."

Jan 1, 2015