Search Documents

By R. H. King

This paper describes the results of an underground coal mine trial installation of a shielded trailing cable. The cable was a three conductor, round, type SHC-GC, and was installed on a shuttle car in a conventional room and pillar mining section. The purpose of presenting the information is to prepare mine operators for proposed legislation that will require shielding on low-voltage trailing cables. Specifically, machine modifications are required to cable reels, packing glands, and couplers. Cable splicing is not as complex as expected but additional materials are needed in the kit and splice training is necessary. Even though shielding will cause some problems for the mine operator, it can reduce the hazard of electrical shock to mine workers. This paper will present information that mine operators can use to solve most of the problems that will be encountered if they are required to install shielded cables. The in-mine evaluation was funded by the U.S. Bureau of Mines.

Jan 1, 1980

By Susanne Pignolet

Ore microscopy has been applied to the complex lead-zinc-copper-cobalt-nickel ores from the Madison Mire in the Fredericktown subdistrict of the Southeast Missouri Lead District to predict potential beneficiation problems. It has been found that in some portions of the ore deposits, textures are present which may result in metal losses. In ores from the Bonneterre Transition Zone the intimate association of siegenite with chalcopyrite may result in cobalt and nickel losses to the copper concentrate. In ores from higher stratigraphic horizons, this association is relatively uncommon, and siegenite is commonly associated with bravoite. This latter association will increase the recovery of the cobalt and nickel in bravoite, even though some of the fine-grained bravoite will not be recoverable. Other textures which may result in potential beneficiation problems include coatings of covellite on chalcopyrite and inclusions of sphalerite in galena.

Jan 1, 1983

By D. N. Hillhouse

The economics of exploration target selection can be measured ultimately only against a company's success at developing mines. In the following brief history of the mine acquisitions of one company, Placer Development Limited, I try to identify the principal targeting parameters and the principal skills that came into play for each property and examine how these have changed with time. The process of target selection in exploration is directed: - first by corporate investment criteria which define objectives and acceptable levels of risk for pursuit of those objectives; - second by experience and skills which permit us to minimize risk; and - third by anticipation of future events relating to ore discoveries and changes in external risk factors.

Jan 1, 1984

By E. J. Ostrowski

The history of ironmaking dates back to 4000 BC when an open forge was used to produce a sponge iron from a heap of ore and charcoal. Even at this early date, man recognized the need for a fuel and a reducing agent. As time passed, man developed new methods of producing iron; however, these developments were centered on the mechanical aspects, and as a result, a furnace evolved which is now known as a blast furnace. During this period of evolution,' man struggled with the only fuel he knew - charcoal. Some 5600 years passed before any attempt was made to use coal as a fuel for the blast furnace. The use of coal had its beginning in 1619 when Dud Dudley of England first attempted its use in the blast furnace; as a-fuel and as a reducing agent. Coal charged to the top of the blast furnace was not satisfactory. The volatile matter of the coal choked the flues, and also the poor, strength qualities would not support the weight of the ore. Breaking up of the coal compacted the stock column to an impervious mass. One hundred and sixteen. years later in 1735, Abraham Darby of England introduced coke as the fuel and reducing agent in the blast furnace. The acceptance of coke as a fuel for the blast furnace was not spontaneous. As late as 1870, one-half of the pig iron product of the United States was made with anthracite coal, 30 per cent with raw bituminous coal and coke, and 20 per cent with charcoal. However, by 1910, 96.2 per cent of the blast furnace product was made with coke, 2.4 per cent with anthracite and coke admixture, and 1.4 per cent with charcoal. Coke became the standard fuel in the blast furnace. As the art of ironmaking progressed, more pig iron was produced and more coke was consumed. Coke oven capacity was progressively increased. In 1910, there existed approximately 4,000 coke ovens; in 1960 there was approximately 15,000 ovens. This increase in coke oven capacity was necessary to feed the mammoth appetite of modern blast furnaces.

Jan 1, 1962

By D. Boreck

The Bureau of Mines is conducting research on the feasibility of incorporating in situ stope leaching into active underground metal mines. Stope leaching, a modified in situ leaching technique, proposes to recover metals by leaching fragmented ore in existing underground openings and collecting and processing the metal-bearing solution to recover the valuable metals. If leaching solutions escape from the stope, either through geologic discontinuities or highly permeable zones in the rock, valuable metals dissolved in the solution may be lost. Escaping solutions may also contaminate ground waters. Consequently, in fractured rock, the characteristics of the fractures in the vicinity of the leaching stope must be understood before introducing actual leach solutions into the stope. Effectively characterizing a rock mass requires the integration of several disciplines including structural geology, borehole geophysics, hydrology, geochemistry, and mining engineering. This paper will focus on the general geologic and geophysical techniques that can be used to characterize the rock mass at an underground simulated stope leaching site. The results of several geophysical logging methods, tested at the site, are compared to the geologic core descriptions. Then, the? effectiveness of the different geophysical techniques in delineating fracture zones will be assessed. Knowledge gained through the geologic and geophysical analyses can be used to supplement results from hydrologic testing. This information can also be utilized in designing blast patterns and developing strategies for controlling or blocking movement of escaping leach solutions.

Jan 1, 1991

By B. A. Carbon

Western Australia is the largest state in Australia with an area one and three quarter times the size of Texas. Most of the State is desert or semi-desert, and only the southwest corner is heavily populated. The State has a population of one and a half million people, and one million of these live in and around the city of Perth. Perth is located on the narrow Swan Coastal Plain and is flanked by the Indian Ocean and the Darling Plateau. The Darling Plateau is an ancient peneplain rising some 300 metres above sea level, and forms an important resource base for the population.

Jan 1, 1984

By Kimberlie Staheli

A new sanitary sewer was installed in Pleasant Hill, California using microtunnelling methods. The project consisted of 693 meters of 1372 mm and 1981 mm concrete pipe. A Herrenknecht AVN 1200 was used to install the nominal 1372 mm pipe in three drives. The machine was then fitted with an oversized shield used to install the large diameter pipeline. This articulated shield allowed the excavation of a 2362 mm diameter hole with a 1524 mm machine-- a technique new to North America. This paper reviews the design considerations for the articulated shield and reports on the project challenges and solutions to overcome these challenges.

Jan 1, 1995

By Augusto Andres Torres Toledo, João Felipe Coimbra Leite Costa, Luciano Nunes Capponi, Diego Machado Marques

Short-term mine planning to open pit requires defining diglines to orientate the excavation geometry. In deposits with multiple chemical variables, it is necessary to have more rigorous control over the feeding of the processing plant. This study analyzes the impact of incorporating multiple chemical variables, the risks generated by geological uncertainty, and the number and starting point locations of shovels in the sequential design of diglines. The objective is to maintain and preserve the low-grade variability, required tonnage, and continuity in sequentially selecting blocks. To achieve this, the probability distribution function of each chemical variable is used while attempting to maintain the ore grades as constant as possible. As it is difficult to maintain multiple elements with low variability simultaneously, the relevance of each chemical variable in the economic benefit is identified. Weights are assigned to signal the importance of each element based on its significance in the recovery process. Several diglines, consisting of sequential blocks, were generated on the same seed point to meet the weekly ore demand. Optimizing the stationarity of multiple chemical variables, accessing and reducing the geological uncertainty performed through geostatistical simulation of grades and transfers functions, considering the number and location of shovels, while meeting the operational restrictions of the selected blocks. The optimized digline with the multiple grades as stationary as possible is retained. The process is illustrated in a phosphate mine. The results show that the proposed method is viable and allows for a quick solution.

Jun 25, 2023

By C. Bailey Williams

Aragonite "sand," an oolitic lime-stone, is distributed throughout the Bahamas on the Grand Bahama Bank, adjacent to Southeast Florida. Bahamian deposits hold 75-100 billion tons of recoverable Aragonite. Aragonite's precipitation from seawater over 700 years ago assures low contaminates, making it a pure material for such industries as cement, glass, etc. A 90-acre, man-made production island was built south of Bimini, adjacent to ocean shipping channels mining is by cutterhead, suction dredge, dewatering, and stockpiling for further drainage and shipping. Aragonite is transferred to the U. S. East and Gulf Coasts via bulk carriers to points of sale.

Jan 1, 1978

By H. Walqui, S. K. Kawatra, C. H. N. Jeltema, T. C. Eisele

"The literature contains many cases where the shape of hydrocyclone efficiency curves vary from the ideal “S” shape. These often appear as changes in slope, or inflections. These inflections can be divided into two categories: “coarse” inflections, which are caused by differences in the density of the minerals being separated, and “fine” inflections, for which there are a number of competing hypotheses concerning their cause. The existing literature addresses either the fine inflection or the coarse inflection, but no studies have reported both types of inflection occurring at once in a single hydrocyclone test. This paper presents hydrocyclone results from both in-plant studies and laboratory experiments that show both coarse and fine inflections. The industrial significance of both types of inflections is discussed. Hydrocyclone efficiency curves show the probability of any given particle reporting to the hydrocyclone underflow as a function of its size. Selectivity functions, S(d), are used to represent the fraction of the feed material in size fraction “d” that reports to the hydrocyclone underflow. Plotting this selectivity function against particle size leads to the standard S-shaped efficiency curve shown in Fig. 1. In the “uncorrected” curve, the tail of the curve does not go through 0%, because a portion of the solids are bypassing classification. This happens as a result of their being carried along by the water, and is most important for the finest particles. The curve can be “corrected” based on the fraction of the feed water that reports to the underflow, represented by the bypass fraction, Rf. The corrected curve then normally passes through 0%, as shown in Fig. 1.The act of correcting the curve shifts the value of the d50 size, which is the size that has an equal probability of reporting to either the overflow or to the underflow. Correcting the curve to account for the bypass fraction makes it easier to compare cyclone performance under conditions that cause the quantity of water in the underflow to change, but that do not alter the actual corrected cut size (d50c).The corrected efficiency curve can be expressed closely by equations such as Plitt (1976):"

Jan 1, 2015

By Paul J. A. Lever, Robert H. King

Human operators, geological conditions, equipment changes, mining sequences, and roof conditions are some of the continually changing operating conditions that drive a dynamic mining environment. These dynamic characteristics make it difficult to automatically analyze mining data because attributes change as the mining environment changes. Mine monitoring systems could provide mine managers with much more useful information than they do presently, if automatic analysis were possible. Automatic analysis of sensor data is also key to autonomous mining systems. This paper describes artificial intelligence (AI) and sensor fusion based sensor data analysis techniques developed over the past four years. These techniques were used to classify machine operating events by continuously monitoring machine power usage in a continuous miner section at an under- ground coal mine. The result is a report similar to an industrial engineering time study. First, numerical pattern classification techniques broadly identify operating events. However, domain knowledge about inter-machine and intra-machine interactions is necessary to identify and refine dynamic event boundaries. By implementing AI and sensor fusion based techniques we are able to classify machine events more accurately and recognize more specific events. These techniques could easily be applied to many different mining sensor data applications

Jan 1, 1993

By Erik S. Bernard

"INTRODUCTION Reinforced Concrete (RC) members such as beams and columns are usually required to include stirrups to maintain post-crack shear capacity, and some may include stirrups that act as confining steel to maintain structural integrity during a seismic event (eg. NZS3101, ACI 318). To achieve seismic resistance, the spacing between stirrups is usually required to be much closer than is ordinarily prescribed for non-seismically resistant structures. Each stirrup must also fully enclose the longitudinal reinforcement with long end-hooks to ensure that the contained concrete is sufficiently restrained during reverse-cycle loading and the reinforcing bars are confined to prevent buckling. The close spacing between stirrups can lead to congestion of reinforcement within members, and can also be expensive to construct due to the labor-intensive nature of steel fixing. A possible alternative to closely-spaced stirrups is the use of fibers to provide restraint and confinement during a seismic event, although this is not yet recognized in codes. Previous experimental research (Jiuru et al, 1992; Filiatrault et al, 1995; Bayasi and Gebman, 2002; Billington and Yoon, 2004) has demonstrated that steel fibers are relatively effective in this application, but suffer the problem that their stiffness can make them difficult to consolidate within an already tight reinforcement cage, especially if they are relatively long (>40 mm). Moreover, steel fiber reinforced concrete (SFRC) is subject to embrittlement with the passage of time, leading to a steady loss of ductility beyond crack widths of 1-2 mm (Banthia and Trottier, 1994; Bernard and Hanke, 2002; Bernard, 2014; Bjontegaard et al, 2014; Bernard, 2015). Since cracks during seismic events are generally much larger than this, embrittlement may present a challenge to the long-term efficacy of SFRC during seismic events. An alternative to steel fibers for enhancement of seismic resistance is the use of macro-synthetic fibers. This type of fiber usually offers the advantage of being flexible so that consolidation is easier between reinforcing bars. They also offer superior durability compared to steel fibers and can reduce flexural crack widths (Bernard, 2016). Several recent small-scale investigations (Ma et al, 2012; Carnovale, 2012; Osorio et al, 2014) have indicated that macro-synthetic fibers can produce meaningful improvements in seismic resistance if used in combination with conventional steel reinforcing bars. The present investigation has extended research in this field by examining whether embossed macro-synthetic fibers can be used to increase the spacing between stirrups while maintaining seismic resistance."

Jan 1, 2016

By Peter J. Szabo

In 1980, a caravan of representatives of Japanese trading companies debarked on the shores of the United States bearing gifts of watches, electronic games, and radios. In early 1983, we find in a parking lot of a major U.S. coal company, a haggard general manager of marketing returning to the Orient with a box under his arm of trinkets of his own; cross pens with company logos, alarm clocks, etc. The tables have turned, but our fellow sitting in a jet plane over the Pacific Ocean had only to heed the warning of the famous 19th Century poet well familiar with the ways of the Far East. Kipling said; "And the End of the Fight is a tombstone white and with the name of the late deceased, And the epitaph drear, a fool lies here who tried to hustle the East."

Jan 1, 1984

By M. Ploc

The grinding process in the mining industry has seen an increased throughput to accomplish greater production and lower overall production costs. Up to 8-9 MW, a single motor can be connected to drive the mill through a pinion and ring gear. Above the single-pinion drive limit, the dual pinion approach was developed to allow two drive motors to be used. This allowed the mill input power to be increased to 16-18 MW. Recent developments in clutch and ring gear materials and design are allowing greater input powers of up to 20 MW to be considered. To avoid damage to the ring gear by uneven load sharing between the two motors, it is critical that the two machines accurately share load. This is typically achieved by either drives capable of controlling load torque between motors or using a GE proprietary control system that accurately controls the load torque from each motor.

Jan 1, 2010

By R. V. Ramani

Minerals, together with agricultural and forestry products, are the primary source of wealth produced in the United States. Although the production of minerals requires only a small fraction of the state's total land surface, as compared with either agriculture or forestry (Table 1), mining activities generally are much more disruptive to the land surface, and rehabilitation is more complex and costly. The past 10 to 15 years have witnessed a sharp increase in mineral exploration and mining, particularly coal mining, which has brought with it an increase in conflict over land use and an increase in negotiations for purposes of mineral prospecting and mining. The general increase in the production and consumption of coal and the particular increase in the percentage of coal extracted by surface mining methods coupled with a growing nationwide environmental consciousness have created increased public concern and in some cases outrage over mining activities. Although there is ample evidence to indicate that it is possible to plan for and design mining activities in such a way that they are compatible with other activities and can thus be made a part of a sequential land-use plan, there is a general lack of knowledge regarding the importance of mining as the provider of basic and essential raw materials to supply society's constantly expanding and increasing mineral needs. This lack of knowledge extends to such matters as land and mineral rights negotiations, the character of mineral deposits and minerals, mineral economics, and land-use planning.

Jan 1, 1977

By Josh B. Taggart

Some twenty to twenty-five years ago we saw the beginning of mechanization in our coal mines, It has now progressed to the point Chat as instruments of production the pick and shovel are things of the past, They had to give way to better and more efficient methods--so mechanization, followed by and combined with automation, has become common-place in our mines. Our coal could not keep its competitive position without this progress Without it our industry could not look to the future with any degress of confidence. Today we lock back and see cases of regained and salvaged markets. We see better coal products being produced at decreasing costs. We see better utilization of manpower and a stronger, more confident industry, Our hats arc off to those mining men, equipment manufacturers, labor leaders, and others who had the foresight to work toward these ends and the ability to bring them about.

Jan 1, 1962

By John J. Simmons

Federal and state regulations, in an effort to reduce acid rain, are becoming increasing more stringent regarding sulfur content of fossil fuels. Whereas coal from Illinois and Ohio contains between 1.5 and 37. sulfur, Wyoming has billions of tons of coal reserves containing less than O.5/% sulfur. However, much of Wyoming's coal is high in moisture, 25-30%, and low in energy, 8,200 to 8,900 BTU, vs. 10,500+ BTU for Illinois and Ohio Basin coals. Wyoming currently ships in excess of 130 million tons of coal to utilities as distant as Michigan, Wisconsin, Minnesota, Iowa, Nebraska, Louisiana, Oklahoma, and Texas. With freight charges ranging from $12.00-$20.00/ton, more than $1.5 billion a year is spent to transport water. A test shipment of more than 50,000 tons of Wyoming coal has recently been made from Mobil's Cabello Rojo Mine, south of Gillette, by Burlington Northern to the Robert's Bank British Columbia coal terminal for transloading and shipment to Taiwan Power Company. This coal assayed approximately 8,400 BTU/lb. and 277. moisture. Carbontec Energy Corporation feels the future availability of dried coal containing 11,000+ BTU could substantially enhance the potential export as well as the domestic market for Wyoming coal. Large and small utilities, along with industrial furnaces require tens of millions of tons of Wyoming, West Virginia, and other Eastern The federal government is encouraging the expenditure of hundreds of million of dollars by utilities to retrofit their boilers to allow them to burn higher sulfur coal. This program, if carried to completion, would cost many tens of billions of dollars, with the net result being high power costs sustained by the utilities. These costs will be passed on and paid for by the American consumer. A sensible alternative would be the burning of low sulfur coal by the utilities, without costly capital and operating expenditures. Carbontec Energy feels the successful operation of a Carbondry Coal Drying Plant in Wyoming will be the forerunner to other similar and larger operations in the State. CARBONTEC RESEARCH The activities of Carbontec's personnel to develop a viable process to dry sub-bituminous and lignite coal goes back some 14 years; in fact, for some of us it goes back to 1962 when we were involved in a program under which lignite coal from Truax Trayer's Velva mine was placed in low sulfur coal, which are burned alone or blended with high sulfur, Midwestern coal. Carbontec believes that a high BTU. reasonably priced, shippable coal fuel produced in Wyoming and delivered at costs competitive with Eastern low sulfur coal, could offer substantial benefits to Wyoming coal producers, utility customers, and to the State of Wyoming.

Jan 1, 1989

By J. A. Murray

Maintaining satisfactory air quality in electro-winning tankhouses has been problematic and costly, particularly as plant operating current densities have increased. Conventional approaches, including the use of beads, hollow spheres, surfactants and coalescer devices, have not proved completely effective, requiring that powerful ventilation systems be installed. As workplace and environmental regulations become more stringent, containment of the acid mist at its source is more attractive. An electrode cap system based on this approach has been developed and tested in two commercial copper electrowinning tankhouses. The design, development, installation and cost of the new electrode cap system are described.

Jan 1, 1996

By Paul Lenchuk

The concrete block industry can trace its beginnings to the early 18th century when most of the experimental work was being carried out in England. In America, the concrete masonry industry got started shortly after the Civil War and has had sometimes a spectacular, but always a steady growth since then. From a few hundred thousand concrete masonry units made in the late 19th century, the industry today produces approximately 3.3 billion concrete masonry units making it the largest industry in the United States for masonry wall materials. There were 3500 concrete masonry plants manufacturing these units after World War II. This nwnber decreased to 1500 by 1970 although the production of concrete masonry units increased by over 100% in the last 25 years. One of the reasons for this increase in production by less than half of the plants which once existed, is the tremendous strides made in automation of production machinery. The concrete masonry plant of today is probably one of the most automated small businesses in existence. Within a few years it will be possible to push a button and the entire manufacturing process will begin with no human hands touching the units until they are laid up in a wall at the manufacturing plant and are trans-ported to the job site. No other concrete product has reached this state of manufacturing sophistication and it is one of the reasons why the price of a concrete masonry unit is not much different than it was 2S years ago. Because of automation, it is safe to say that concrete masonry will remain a highly competitive building material for many years to come. The problems that beset the continued use of this material are not related to the cost of manufacturing and delivering the product. What are some of the problems as well as some of the opportunities and is the golden age of opportunity knocking rather than a wolf in disguise? The use of concrete masonry has grown each year because a larger unit was provided at less cost than other competitive materials. Concrete masonry has had severe competition from the clay products industry as well as masons who laid the product in the wall and who resisted concrete masonry for many years. Even today

Jan 1, 1971

By Geo. A. Wells

Abstract The consumption of barytes in certain paints polyurethane foams, seamless, flooring, glass, brake linings, plastisol caskets for food containers and in fluids used for gastrointestinal X-ray examinations rely on tie unique properties of barium sulfate, There are no readily available mineral substitutes. Barytes are also the essential raw material for the manufacture of industrially important barium chemicals. High quality barite ore has become scarce throughout the world. Processing ore into quality end products is both capital and energy intensive. These factors have tended to limit availability and increase prices which have encouraged the use of alternates and restricted market growth.

Jan 1, 1980