Search Documents

By F. T. Paleari

Radial gas holdup profiles have been measured in a 50x400 cm flotation column using a multi-cell conductivity probe. Three different bubble generation systems were examined: up to eight vertical filter cloth spargers, three horizontal filter cloth spargers, and three (horizontal) Cominco-type spargers. The variables tested were: number of spargers, symmetry of their arrangement, and height above spargers. Batch water with up to 20ppm frother concentration was used. The general observation is that the profiles tend to be uniform (i.e. flat) with some exhibiting a slight wavy shape. The vertical sparger arrangement proved the most difficult to achieve profile symmetry. The horizontal spargers gave uniform profiles at right angle to their length but a decreasing gas holdup along their length; the Cominco-type spargers gave slightly less scatter in the data. Switching off selected spargers (to simulate malfunction) did not produce strong asymmetry in the profiles.

Jan 1, 1993

By Alireza Ayoubian, Richard Finno

The network of freight tunnels in Chicago consists of about 62 miles of horseshoeshaped tunnels constructed typically less than 50 feet below ground surface. These tunnels serve as repositories of much infrastructure and should remain serviceable. The tunnels are often impacted by adjacent excavations and the question arises as to the existing state of stress in the final liner. This paper discusses construction of these tunnels and presents the results of finite element analyses which were used to obtain ranges for axial forces and bending moments that have developed in the final liner of the freight tunnels since their construction.

Jun 13, 2023

By D. Spitty

There are enormous complexities with mine planning and the problem itself presents a huge challenge to the existing mine planners performing this activity. Mine planning optimization supports planners to determine ?What are the best increment excavation sequence and the best material blending combination such that throughput, quality, cost, utilization and Net Present Value (NPV) targets are met?? It is achieved through using an advanced scientific approach that has been specifically adapted to address the mine planning dilemma.

Feb 23, 2014

By B. E. Davis

A problem that has continued to plague the Florida phosphate industry is the loss of coarse phosphate in the flotation circuit. Attempts to remedy this problem such as floating the coarse material (plus 425 µ m) in a separate circuit have resulted in limited success, but recovery is still not optimum. The Bureau of Mines is investigating ways to improve the recovery of coarse phosphate through improvements in the conditioning step. Studies to optimize conditioning parameters such as agitation energy, conditioning time, conditioner solids, and residual clay content have resulted in improved P2O5 recovery. Optimizing these and other conditioning parameters resulted in a rougher concentrate grading 30 pct P2O5 with a P2O5 recovery of 97 pct.

Jan 1, 1993

By C. O. Petter

This paper, in its first part, compares the profile and economic weight in the extraction of industrial minerals and aggregates to the so called conventional mining activities (metals, coal, gas and oil extraction) in Brazil. In its second part, a descriptive analysis of the present situation of the education in Brazil is made, emphasizing the graduation and post-graduation formation especially in engineering. The curricular structure of the schools that prepare the mining workforce is discussed and the presence of specific subjects in industrial minerals is evaluated. Finally, considerations are made on the actions being taken in the main universities and companies, aiming to improve the formation of the specialized workforce. The Brazilian mining production, comparing 2010 to 2011 showed an expansion of more than 3% (IBGE, 2012). Not bad, but nothing to do with the 13% growth between 2010 and 2009 (influenced by a recovery effect from the 2008 commodities? nightmare). The commodities that had a rising behavior were titanium, gypsum, nickel, graphite, bauxite, phosphate, chrome and chrysotile. All of them were eclipsed by the impressive growth of iron ore production. Some decreases could be noticed, eg. in zinc, kaolin, magnesite and salt production (DNPM, 2012). In fact, the mining activities followed the positive growth of the country these last 5 years. The commercial balance (exports against imports) was not spectacular (positive in US$ 30 billion in 2010). It is important to notice that the mineral commodities balance was US$ 35 billion, representing 27.4% of the total exports and 15.6% of the total imports of Brazil (DNPM, 2012). In this positive environment, the workforce in Brazil showed progress in number of formal jobs and average revenues.

Feb 23, 2014

By X. Wu

A quantitative damage evaluation caused by ground motions associated with strong roof caving is presented. The strong roofs are modeled as either cantilevering or bridging beams over continuous elastic foundations subject to an exponentially distributed vertical stress. Major factors influencing roof caveability and strain energy buildup are identified and investigated. A methodology to evaluate the strain energy accumulation caused by overhanging roof is presented. The potential for mine tremors is determined in terms of the local Richter magnitude ML which depends on the seismic energy transformed from the stored strain energy released when the roof fails. A particle velocity model is applied to estimate the damage area associated with roof collapse. A case study from a Utah coal mine shows that estimations of bump severity and damage area agree well with the field observations.

Jan 1, 1995

By Peter Jackson

Over a quarter of a century ago a New Zealand physicist suggested the possibility of detecting coal seam discontinuities by a seismic method carried out underground in the mine workings (Evison 1955). Twenty years ago initial experiments were performed in Germany (Krey 1963). Since then research has continued, notably in Britain and Germany, in order to provide a reliable fault and washout detection system. The National Coal Board of Great Britain has now carried out more than 250 surveys in Britain, France and Australia. The first NCB survey in the U.S., a successful application of the technique to an Ohio coal seam, will be described and the strengths and limitations of the method explained.

Jan 1, 1984

From 2009 to 2012, Aker Wirth, in cooperation with the BGR (German Federal Institute for Geosciences and Natural Resources), developed a concept for the deep sea mining of manganese nodules, which it also examined by means of a profitability analysis. The study was undertaken for the German Federal Ministry of Economics and Technology. The increasing scarcity of resources, coupled with the continuous rise in resource prices, drive the search for new raw material deposits. As a result, the deep sea is coming increasingly under the spotlight. At depths of more than 1,000 m (3,280 ft), large deposits of ores and precious and high-tech metals, such as manganese, cobalt, nickel, copper and gold, along with rare earths (which are important for the high-tech industry), can be found. The extreme deep sea conditions ? enormous water pressure, ice-cold temperatures and complete darkness ? present huge financial and technical challenges to the mining industry when extracting these materials. Aker Wirth has recognized the potential of this important future market early on and advances the development of relevant products.

Jan 1, 2013

By Clinton A. Hollingsworth

The Flotaire Flotation Cell is a simple, efficient hydraulic/pneumatic Flotation Cell that has no moving parts. It is normally used in conjunction with a surfactant (frother) in which case the combination is known as "The Flotaire System". On many ores, metallurgical efficiencies are substantially increased and operating costs reduce. For example, in floating phosphate rock, it is not unusual for BPL recovery to be increased more than 10%, the major increase being due to floating coarse phosphate, up to 14 mesh, and the difficult to float phosphate. Substantial improvements have also been made on coal, mica, vermiculite, kaolin, barite, copper, etc.

Jan 1, 1981

By R. R. Young

Good afternoon gentlemen. It is always a pleasure to talk about a subject dear to our hearts--the high speed transfer of bull; materials. Specifically, today we will be reviewing the engineering approach to an age old problem of ship loading and unloading. You may be puzzled by the title of this paper and we will attempt to explain this for you--particularly the use of the words "New Era", since high speed automated facilities are nothing new to the material handling engineer. The new era in material handling designs refers to an all out concerted effort to provide custom engineering tailored to specific operations and economic requirements of the client. It shuns hardware type of engineering wherein existing machines and devices are dusted off and reapplied. It provides automation when automation can be justified and it exemplifies the application of systems engineering to solve specific problems.

Jan 1, 1967

By J. Sanko

When faced with the task of designing a process control system the control engineer must consider the following: 1. The type of process to be controlled and the manner in which the process must be controlled (the algorithm). 2. The type of equipment to be used to implement the control system. 3. A means of describing the control system for use in the following areas: a. Project engineering. b. Procurement of the control system equipment. c. Plant startup. d. Operator training and reference.

Jan 1, 1981

By Greg Struble

The Homestake Gold Mine is one of the deepest and most extensively developed hardrock mines in North America. The mine is divided into five divisions which produce a total of 1.7 million metric tons of ore per year. In the past, labor intensive mining methods such as open cut-and-fill, shrinkage, and timber stoping were utilized. In recent years there has been an extensive change to the more productive methods including Vertical Crater Retreat and Mechanized Cut-and-Fill. Also, the percentage of production from the lower divisions below the 4850 level is increasing while upper level reserves are beginning to decline. Combined, these factors have strained the ventilation resources to the limit. By early 1984 it became clear that future production trends would require a detailed study of future ventilation resources. By November of 1984 the Ventilation Department completed a study to project these future requirements. This paper will detail the first phase of a scheduled two phase upgrade: the installation of a new surface fan.

Jan 1, 1987

By Milka Madahana, John Ekoru

Particulate matter is one of the leading pollutants in the mines and in the communities in the areas near or surrounding the mines. The availability of large Clinical and environmental data sets obtained from the mines has brought about the need to use better approaches to analyze the collected data. Prediction and control of particulate matter concentration in the mining environment is essential in minimizing air pollution and protecting the respiratory health of mine workers. The main objective of this research work is to analyze datasets obtained from a mining area using machine learning techniques which will then be followed by the real-time estimation of dust particulate in the mines. Datasets collected over 8 years in an hourly sampling rate from an open cast mine is cleaned and analyzed for trends and patterns. Artificial Neural Networks (ANNs), Support Vector Machines and decision trees techniques are applied to analyze and predict the particulate concentrate. The estimation of particulate concentration using Artificial Intelligence will significantly contribute toward the development of quantitative tools to be used in correlating of cause and effect of dust concentration in mines. The results obtained in this work will form a sub-unit of a respiratory health monitoring system for mine workers. The system is essential in the collection, analysis, and tracking of mine workers’ respiratory health, thus it forms part of an early intervention system for mine workers. From the existing theory, we expect the Artificial Neural Network will perform much better than previously used classical models.

Jun 25, 2023

By N. J. Ferguson

An upsurge in demand for Australian coal has seen a much needed programme for a new generation of coal ports. This paper discusses design concepts in planning a large modern terminal, with the 25 Nt/a Port Kembla and the 50 Mt/a Newcastle facilities as practical examples. The need is emphasised for a studied Master Plan, in-built materials handling flexibility and staged development. Trends in bulk ship design and loading methods are noted. Features of these Australian designs include methods of dealing with poor ground conditions, functional civil engineering for environmental protection and optimal marine structure designs.

Jan 1, 1982

By William H. Peterson

How is the Government's oil import control program doing? In July 1954 Mr, Eisenhower established the Cabinet Committee on Energy Supplies and Resources Policy. On July 29, 1957, the Administration imposed "voluntary" company oil import quotas on American oil importers to maintain "a healthy domestic (oil) production industry" and safeguard "national security." On March 10, 1959 the President by proclamation made the voluntary program mandatory. But study of the program in practice shows that it is not working out as expected and-that there is some doubt that its aims and other related Administration purposes are being achieved. Take the Administration's anti-inflation policy. To be sure, the President apparently recognized in his March 10th proclamation that in restricting cheap imported oil in favor of more expensive-domestic oil he was making the inflation fight that much harder, for he called for Government surveillance of domestic oil prices to prevent them from getting out of hard, And indeed while domestic crude oil prices have not risen appreciably during 1959 neither have they fallen appreciably (although there has been some price weakness in the past few weeks).

Jan 1, 1960

Unplanned ore dilution can have severe impact on the economics of a mining operation. The paper discusses and distinguishes between controllable and natural parameters influencing ore dilution, and how it can be minimized in longitudinal mining systems of narrow vein orebodies. It is shown through data of surveyed stope profiles and numerical modelling that unplanned ore dilution is a function of stope design and construction, orebody geometry, and rock mass characteristics.

Jan 1, 2010

By Richard B. Stein

This paper will present an overview of several hydrometallurgical processes which can be used for sea-nodule metal recovery and some simplified economics. Before going any further, here are some of the basic figures from which the economics were developed. The first is to establish a representative composition for a typical nodule feed (Slide 1). This set of chemical analysis figures can be taken as typical for a deep Pacific nodule feed and shows manganese at 30%, copper at 1.1%, cobalt at 0.2%, nickel at 13% and iron at 10% for the metals of economic interest1.

Jan 1, 1982

By M. G. Hester

The inadequacy of traditional geostatistical methods for estimating some precious metals deposits has become apparent in the last few years. New methods or estimation such as Indicator, Probability and Multigaussian Kriging are difficult to understand and apply. Case studies using a new method of variogram calculation proposed by Srivastava show the method valuable for variogram estimation in precious metal deposits. Some simple, sometimes unorthodox. estimation methods that have proved useful in Some situations are presented.

Jan 1, 1990

By C. G. Anderson

The treatment of materials for the recovery of the precious metals imposes many processing and environmental challenges. Sunshine Mining and Refining Company has developed hydrometallurgical technology for recovery of values from refractory precious metal materials. At Sunshine, the industrial focus of these processes has been for the direct recovery of silver without cyanidation. However, recent work has indicated that these technologies can provide a means for treating complex, refractory gold concentrates. This will be the focus of this paper. The practice of pretreating ores and concentrates to make them more amenable to cyanidation is becoming more common. Several pretreatment options for sulfide concentrates containing gold include roasting, bio-leaching, direct pressure oxidation and nitrogen species catalyzed pressure oxidation. The industrial use of nitrogen species catalyzed pressure oxidation has been limited to the Sunshine refinery where its focus has been for the treatment of silver concentrates. Much of the reluctance, outside of Sunshine, to use this type of technology may be based on the perception that high costs are associated with using nitrogen species (e.g. nitric acid, sodium nitrite) to leach. Also, the use of nitrogen species catalyzed pressure oxidation on an industrial scale is unfamiliar to most metallurgical professionals. A summary of pressure leaching processes which utilize nitrogen species as a catalyst is presented in Tables 1 and 2.

Jan 1, 1996

By C. Opoku-Ware, M. Kukay, P. Conrad

"This project is exploring the potential for developing trees tolerable to degraded un-reclaimed mine site soils and tailings as a solution to re-establishing long-term tree growth on those sites. The project incorporates growing tree seedlings in an underground greenhouse grown from seeds planted in the degraded mine soils in which they will eventually be planted. The outcome of the project is expected to lead to a successful solution for re-establishing tree growth in soils and tailings containing high metal concentrations with minimal post-planting human intervention. The research is being conducted in an underground greenhouse located 100 feet below the surface in the old Orphan Boy Mine Underground Mine Education Center (UMEC) located on Montana Tech’s campus in Butte, Montana. INTRODUCTION In an effort to improve Butte Area One natural resources, the research project was proposed to help restore tree growth in the Butte Priority Soils Operable Unit Boundary (BPSOU). Research by Blicker, et al. (2003) found that, the BPSOU, which is part of the Silver Bow Creek/Butte Area National Priorities List (Superfund) Site within and near Butte, Montana has multiple historic mining sites situated entirely within the urban setting of Butte. Mine wastes and mill tailings, accumulated from over 100 years of gold, silver, and especially copper mining are dispersed throughout Butte, posing health risks to human and environmental receptors. Stabilization of tailings sites is needed to control fugitive dust, prevent run-off of toxic material resulting in subsequent sediment deposition in streams, reducing the volume of water seepage through acidic and heavy metal contaminated material, and improving land productivity and aesthetic VALUES ((Watkin and Watkin, 1982). If successful, the project will help restore water quality and maintain stream flow in Silver Bow Creek where it flows through Butte Area One. Trees native to Butte are being grown in an underground greenhouse located in the UMEC and will be planted in five areas located within the BPSOU designated for tree planting by the Butte Silver Bow government. Growing trees is expected to help restore vegetative ground cover within the watershed contributing to stream flow in Silver Bow Creek. They will prevent soil and tailings from eroding and being deposited in Silver Bow Creek where they could degrade water quality and choke stream flow."

Jan 1, 2018