Search Documents

By L. R. Nelson

Cyprus Pima is a medium-sized open-pit copper mine located 35 km (22 miles) south of Tucson, AZ. The ore body was discovered using geophysical prospecting methods in 1953 and was originally worked as a small underground mine followed by small open-pit operations. As mining equipment grew larger and the economic ore grade dropped, the operation grew in size, through four expansions, to the present 50 500 tpd (56 500 stpd) milling rate. The remaining stripping ratio is about 2.5 to 1. Mining equipment includes 11 electric shovels ranging in size from 6 to 15 m3 (8 to 20 cu yd) and 42 diesel-electric haulage trucks ranging in size from 89 to 223 t (100 to 250 st). Mine planning is performed at Cyprus Pima to serve several functions. The most important is to plan ahead, one year at a time, to predict the ore grade and stripping requirements on a month-by-month schedule. This yearly plan is necessary for budget preparation and is revised once each quarter to incorporate variations in actual production experienced during the preceding quarter.

Jan 1, 1979

By D. W. Rierson

Svedala has a ported kiln process, designed specifically for the direct reduction of pelletized or natural lump iron ores. The process is called ACCAR. This ported kiln technology has been coupled with Svedala's GRATE-KILN System, for iron ore pelletizing, into the GRATE-CAR System for the reduction of fine grained ore concentrates through the steps of agglomeration, induration and reduction in a single production line. Additional applications of the GRATE-CAR System include: the recovery, agglomeration and reduction of steelmill waste oxide fines and the use of minus 6mm size natural lump ores to produce a highly metallized pellet agglomerate. Svedala conducts tests to confirm certain operating parameters through process simulations of the GRATE-CAR process. These tests are conducted at Svedala's Process Research and Test Center, Oak Creek, Wisconsin. Svedala also assesses issues of process variables, heat transfer, equipment sizing, retention time and endothermic demand associated with iron ore reduction using natural gas or coal as the reductant. The purpose of this paper is to present the GRATE-CAR processing concepts, the commercial production line and the testing procedures associated with investigating potential raw materials.

Jan 1, 1997

By M Aboagye, K Appau, W. Assibey-Bonsu, C. Muller

A case study based on two recoverable resource modelling techniques (indirect and direct or localised methods) have been derived using typical feasibility study or new mine drilling data configurations from the extensions of an existing mine’s massive production database. The database is from the Gold Fields Tarkwa Gold mine (~6Moz Mineral Reserves and 13-year Life-of mine). The corresponding recoverable resources from the various techniques are then analysed using the open pit Whittle optimisation process. The results were then compared based on the Whittle optimisation results to determine the efficiencies of the approaches and the validity of the recoverable mineral resource estimates for mine planning and financial forecasts (including Cash Flows etc). Based on historical production metal recovery, the paper also assesses the corresponding orebody and mine planning as well as financial risks with regards to the modelling techniques. The study shows that the localized direct and somewhat more straight forward approach if applied efficiently can provide an equally useful tool for computing recoverable resources for mine planning and financial forecasts, as compared to the indirect approach as presently in use.

Jun 25, 2023

By W. J. Wuest, M. J. DeMarco, J. R. Koehler

Yield-pillar-based gate-road designs often fail to provide mine operators with adequate ground control. This is because of the unknowing m is employment of "critically" sized pillars. A "critical” pillar is one that is too large to either yield nonviolently or to yield before the roof and floor sustain permanent damage and is too small to support full abutment loads. To demonstrate the critical pillar concept, afield study of a tapering gate road was conducted by the US Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m (55.1-ft) wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m (40-ft) wide design more closely approaches proper yield pillar dimensions. A probe hole in several 10.6-m (34.8-ft) wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1997

By F. P. Schwarz, A. J. Erickson, S. M. Weber

The Mount Hope stockwork molybdenum exposit, Eureka County, Nevada, occurs in a small igneous cauldron complex 32 to 38 mybp in age. The deposit is characterized by alteration zones and mineralized shells symmetrically distributed around multiple intrusives. For samples from the 25 000 meters of 1981-82 drilling, an appraisal of error in in-house sample preparation and in commercial assaying has been made. After splitting, drill core is crushed and reduced in volume (8:1 at 10-mesh, 8:1 at 70-mesh, 6:1 at 200-mesh) to supply 25 grams of 200-mesh pulp for replicate analyses. A 0.5 g portion of the pulp is used for dissolution and atomic absorption analyses. Factors which initially generated unacceptable data variances have been minimized by planning, repeat analyses, introduction of standards, and routine monitoring. Assuming that error between replicate assays defines a Gaussian distribution with its average ideally equal to zero, precision (from preparation including core splitting and analysis of 8400 pairs of molybdenum samples) is on the order of + 25%. The error distribution is not biased. Accuracy is approximately 4% lower than absolute as determined by replicate assays of commercially prepared samples.

Jan 1, 1992

By R. A. Metz, George S. Barnett

The Equis and El Roble projects are located in the Cordillera Occidental of Colombia. The Equis vein deposits have sulfide ore reserves of 95,955 mt (105,770 st) grading 8.51 g/mt (0.248 oz/st) gold and 12.4 g/mt (0.36 oz/st) silver with 0.94 % copper, 1.10% lead and 11.06% zinc. Ore reserves at El Roble are estimated as 1.1 Mmt (1.21 million st) grading 4.89 % copper and 3.39 g/mt (0.099 oz/st) gold. Geologically possible reserves at Equis may total 1.6 Mmt (1.76 million st). El Roble has the potential to contain several tens of millions of metric tons. Exploration included diamond drilling, trenching, channel sampling, rock and soil geochemistry, geophysics and tunneling. Erratic high grade samples affect the weighting of channel and drill core samples. Secondary reconcentration of gold is also a factor. Sample maps and graphs show the distribution of values to be highly variable. Geostatistical treatment of some of these data gave important guidelines for parameters such as sampling densities, drill hole spacing and confidence limits.

Jan 1, 1992

By J. Bigu

A theoretical radiation mine model, suitable for underground uranium nines, has been investigated. In this model, the rate of ventilation and/or the radon (thoron) gas emanation from mine walls are time-dependent. Several cases of practical interest have been investigated including sinusoidal, linear, exponential, stepwise, or a combination of two or more of the above. Analytical solutions were obtained for the time-dependent radon (thoron) gas emanation rate. However, because of the extreme analytical complexity of the solutions corresponding to the time-dependent ventilation rate case, numerical solutions were found using a special Runge-Kutta procedure and the Hamming's modified predictor-corrector method for the solution of linear initial-value problems. The mine model makes provisions for losses of radioactivity, other than by ventilation and radioactive decay, by, say, plate-out on mine walls, and by other mechanisms. Radioactivity data, i.e., radon, thoron, and their progeny. obtained with the above mine model for a number of ventilation and emanation conditions, are presented. Experimental data obtained in an inactive stope of an underground uranium mine for a time-dependent air flow case are shown. Air flow conditions (ventilation rate) were determined by tracer gas techniques using SF6.

Jan 1, 1987

By B. R. Utz

The goal of the DOE Coal Preparation Program is to provide industry with the scientific and engineering knowledge base to produce economically competitive and environmentally acceptable clean coal products for both existing and new markets. The DOE/PETC in-house program continues to conduct fundamental, exploratory, and applied research in the areas of physical, chemical, and microbial coal beneficiation to assist in meeting these goals and objectives. The Coal Preparation Division now has a new Coal Preparation Process Research Facility that allows continuous bench-scale testing of emerging coal cleaning technologies and ancillary coal preparation equipment at feed rates up to 1,250 kilograms (1.25 tons) per hour. Bench-scale and laboratory-scale research projects at PETC cover areas such as 1) the use of micronized-magnetite for fine-coal, 2) heavy-media cycloning, 3) fine coal reconstitution, 4) development and testing of coal preparation process flowsheet simulators, 5) dry coal beneficiation using electrostatic methods, 6) tracer methods to determine the efficiency of density-based separations, 7) selective oxidation of organic sulfur, and 8) microbial removal of pyrite and organic sulfur from coal. This paper will discuss several of these research areas.

Jan 1, 1993

By L. R. Stoiser

The mineral resource potential of the Los Bronces deposit was successfully evaluated by an intense, coordinated field program over a 37-month period (April 1978 - May 1981). This project was part of a much larger study to determine the economic feasibility of expanding the open-pit, mine-mill operation 10-fold to 80 kt/d (88,000 stpd). The resource project included more than 120 km (74 miles) of core drilling and 64 km (40 miles) of drill rig access way construction under adverse topographic and climatic conditions, detailed geological mapping, and other related activities. The Los Bronces deposit is composed of an earlier mineralized porphyry-type body intruded in part by a large complex of mineralized hydrothermal breccia pipes. The mineralization is hosted by intrusive and extrusive igneous rocks. Various stages of erosion, oxidation, leaching, and supergene enrichment of copper are present. Drill hole indicated geologic reserves are estimated at 1.3 Gt (1.4 billion st), averaging 0.81% copper and 0.016% molybdenum at a cutoff grade of 0.6% copper equivalence decreasing to 0.25% over the life of the mine. Trace amounts of silver are also present.

Jan 1, 1987

By G. T. Lineberry, R. S. Mateer

Often only after years of "technical dormancy" do errors in published literature become apparent and meaningful. To prevent duplication of effort for future generations, the following corrections are offered. These errors were discovered during a recent study in which a computer program for mine hoist rope selection was developed (Lineberry and Mateer, 1988). In order of increasing gravity: Captions for Figs. 3 and 4 are transposed. Purported to be a more accurate method of rope selection than the process of successive approximation, the direct method assumes linearity between a given rope's minimum breaking strength, T, and unit rope weight, WV. Because of the sensitive location of the constant, K, in equation (8) for breaking strength, the significance of this nonlinearity is magnified. For a typical 6 x 37 class fiber core wire rope (Wire Rope Corp. of America, 1985), K actually varies from 43,650 to 52,190, depending upon rope diameter. Although the direct solution permits a rapid selection of hoist rope, an indirect (iterative) solution procedure is favored because of its improved accuracy and ease of computerization. Equation (8) for minimum breaking strength is in error. It should read:

Jan 1, 1990

By J. G. Groppo, B. K. Parekh

A series of performance studies were conducted using countercurrent column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia using a 150-mm (6-in.) inside diameter column that was 5.8 m (19 ft) high. Both thickener feed and classifying cyclone overflow with a typical size distribution of 150 µm (100 mesh) X 0 were tested. The percent solids of the column flotation feed varied from 1.5% to 15% while the ash content ranged from about 30% to 60%. The concentrates produced contained 2% to 10% ash with Btu recoveries of nearly 90% using 0.12 to 1.25 kg/t (0.25 to 2.5 lbs per st) fuel oil and 0.12 kg/t (0.25 lbs per st) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from seven different seams are discussed as well as scale-up relationships used to design a full-scale installation presently in operation.

Jan 1, 1991

By J. W. III Leonard, T. E. Wilson

In addition to coalbed thickness and basic coal quality data, coal drill cores can produce design data for coal beneficiation processes. To generate design data, a coal drill core should be reduced from its original cylindrical form to a particle size distribution and composition that represents (with the possible exception of top size) a raw coal process stream. Reducing a coal core with a crushing machine rarely accomplishes this representation. This investigation employs drop-shatter impact breakage followed by dry batch tumbling in a steel cylinder rotated about its transverse axis to characterize the core in terms of first-order and zeroth-order break- age rate constants, which are indices of the propensity of the coal to degrade during handling. To reduce composition variables and conserve difficult-to-obtain coal cores, the initial drop-shatter and dry-tumbling tests were done with synthetic cores. Then, cores from three coal beds, Illinois No. 6, Upper Freeport and Pocahontas No. 5, were tested. Comparison of a crushed drill core and a drill core prepared by drop-shatter and tumbling indicated that the size distribution and size fraction composition of the drop-shattered/tumbled core more closely resembled the plant feed.

Jan 1, 2000

By Brian Fulcher

The Fort Lawton Parallel Tunnel was built in 1990 - 1991 by Morrison Knudsen Corporation (MK) as an integral part of Seattle METRO's planned expansion of the Westpoint Treatment Plant. The project included a concrete lined 2542 m (8,340 ft) long tunnel bored in sands and clays under the presence of methane gas and over 27.4 m (90 ft) of ground water table. The tunnel roughly paral¬lels an existing and still operating 3.65 m (12 ft) diameter tunnel originally completed in 1909. The parallel tunnel was constructed using a Lovat 4.72 m (15 ft-6 in) earth pressure balanced TBM with ribs and timber lagging as primary support. The tunnel alignment crossed under as much as 91.4 m (300 ft) of overburden as well as twin mainline railway tracks; terminating in a shaft adja¬cent to the Seattle ship canal. The project was completed in June, 1991 after a final "wet-tap" tie-in to the existing brick-lined sewer; over five months ahead of the contract schedule. This paper will describe the construction methods, job site conditions and difficulties encoun¬tered on this very challenging and successful project.

Jan 1, 1993

By W. Addy Majewski, Kenneth L. Bickel

The U.S. Bureau of Mines (USBM) and Diesel Controls Limited evaluated a new diesel emission control system on an underground mine vehicle. The system was a catalyzed ceramic wall-flow diesel particulate filter (CDPF) combined with an catalytic converter, or diesel oxidation catalyst (DOC). This paper describes the design and installation of the system on a load-haul-dump (LHD). The results of screening tests conducted by the USBM are also given. The screening tests were conducted to determine if the device's particulate collection efficiency, regeneration temperature, and effect on gaseous hydrocarbon (HC) and carbon monoxide (CO) emissions changed over the period it was being used. The system was removed from the LHD and evaluated in the laboratory after operating for 308 and 1200 hours. After 308 hours of operation, laboratory testing revealed its particulate collection efficiency varied from 41.0 to 93.5 percent, depending on engine operating conditions. Its regeneration temperature was about 415° C. It reduced HC emissions by up to 97.6 percent, and CO by up to 95.0 percent. When tested in the laboratory after operating for 1200 hours on the vehicle, no significant change in performance was observed.

Jan 1, 1995

By B. W. Cavender

Innovative mining and metallurgical operating techniques or processes can be identified and developed by systematically analyzing change as it occurs within the mine, plant, technology, or industry. Sources of change to be monitored for innovative opportunities include unexpected successes or failures, incongruities between perceived and actual events, process needs, changes in perceptions, and the development of new knowledge. Innovation can be effectively organized, practiced, and managed. The perception of change as an opportunity rather than a threat is mandatory, as is the systematic measurement of innovative performance. Innovation is enhanced by specifically-designed policies regarding organizational structure and staffing, daily management practices, and compensation and incentives.

Jan 1, 1994

By W. Dresler

Since 1900, smelters have produced in Canada over 10 million tonnes of iron silicate waste slag containing significant quantities of nickel, cobalt and copper. The slag is reduced with aluminum and calcium oxide additions to produce a copper, nickel, and cobalt enriched alloy and an obsidian slag. It was found that the obsidian slag contained very low copper, nickel, and cobalt contents, indeed below 0.06% of each the base metals. These metals have been collected in a type of ferroalloy with up to 1.6% Cu, 2.1% Ni, and 0.7% Co. These alloys can be recycled according to standard procedures in base metal smelters. Surprisingly, the obsidian slag was found to display good cementitious and pozzolanic properties, which is a requirement for cement production. The strength producing properties of the obsidian slag are considered to be exceptional at the 28 day standard test age. In most cases, the obsidian concrete is characterized by significantly greater strengths than control concrete tests and concrete containing fly ash or blast furnace slag. Compressive strength data at 365 days for the obsidian concrete is impressive.

Jan 1, 2003

By J. R. Hindman

The vermiculite review arrived too late for the June issue. In 1992, production of commercial vermiculite in the United States increased 1 % to 170 kt (187,000 st), according to the US Bureau of Mines. The estimated value of vermiculite concentrate was $13.6 million, yielding an average value of $80/t ($72.50/st). Vermiculite is used in several physical forms. Use of the thermally exfoliated product include light weight aggregates, horticultural growth media, thermal insulation applications and absorbents for spill control and liquid waste containment. The untreated commercial concentrates are used as intumescent fillers in plaster board, gaskets and paints. Several chemically modified vermiculite products include clay-sized dispersions and granules for treating flue gas. South Africa was the only major foreign source of vermiculite used in the United States. It exported about 40 kt (44,000 st) to the United States last year. In 1992, Palabora Mining Co. began processing vermiculite in a new beneficiation mill at Phalabowra. It produced about 164 kt (181,000 st). Minor sources of foreign vermiculite concentrates consumed in the United States included about 140 kt (154,000 st) from China. Brazil also exports some concentrate to the United States.

Jan 1, 1993

By Alf Thidemann, Per Marius Nilsen

Tunnelling with hydraulic drills has been a success in Norway. In the fall of 1976 excavation of tunnels for the development of the Aabjoera scheme was started. Two and a half years later a total of 25 kilometers of tunnels are completed. During the most busy period 5 rigs with hydraulic drills were in operation. GENERAL INFORMATION. Aabjoera Hydro Electric Plant is located in the central part of Norway (Fig. 1). The scheme covers a mountaineous area between the Tosen Fiord and the valley of Namdalen. Water from the area of precipitation is transferred through 5 tunnels to the main reservoir. From here the water is conducted via a 10 km long, unlined supply tunnel down to the Kolsvik power station. The power station is situated underground with a short tailrace tunnel out in the fiord. Average head of water is 507 m. The Aabjoera plant is jointly owned by Helgeland Kraftlag A/S, 8650 Mosjøen and Nord-Trøndelag Elektrisitetsverk, 7700 Steinkjer. The Civil Engineering Division of the latter company has acted as Consulting Engineers for the scheme. General contractors for the whole scheme has been Ing. F. Selmer A/S, Box 6035, Etterstad, Oslo 6.

Jan 1, 1979

By Bernardo Portillo, Alejandro Perez, Daniel Norrgran, Joseph Wernham

High gradient permanent magnetic separators (termed "Ferrous Wheel") are described as used to recover the iron bearing minerals from mill tailings at the Grupo Acerero del Norte's Hercules iron mines in Coahuila, Mexico. The pilot scale test work as well as the "in-plant" test work provided the basis for a 385 MTPH plant expansion to be commissioned late in 1995. Approximately 6 million metric tons of flotation tailings averaging 50 percent iron, mostly as hematite, are contained in two separate ponds. The tailings are relatively fine at 93 percent -200 mesh and 72 percent -500 mesh. After testing various recovery methods, a high gradient permanent magnetic separator was selected to produce a preconcentrate prior to flotation. The separator uses a flux converging matrix to generate high gradient magnetic fields and capture the hematite. The advantage of the Ferrous Wheel high gradient permanent magnetic separator is the use of permanent magnets as opposed to electro-magnets. Further the vertical rotating ring is much more conducive to matrix cleaning as opposed to the conventional horizontal ring separators. This feature also allows the use of a wide range of matrix materials to achieve the optimum metallurgical response

Jan 1, 1995

By Michael D. Loy

This paper examines the computerization steps of United Coal Company of Bristol, Virginia. OVERVIEW Producing close to 7,000,000 tons per year, United Coal Company is one of the most interesting mining companies in the east. Their approach to mining reflects a dedication to modern technologies and extraction methodologies. With varying amounts of production coming from four divisions (a fair amount of production comes from contract operators) and over a billion tons in recoverable reserves, United rests heavily on the planning and engineering efforts of a centralized engineering group. Although each division relies on its own engineering personnel for day-to-day management and operations, long range planning and reserve management is conducted at the corporate engineering level. This group, while extremely competent and efficient, is relatively small (7 people), when compared to the needs of a large mining company.

Jan 1, 1985