Search Documents

By G. Simmons

Santa Fe Pacific Gold Corporation (SFPGC) conducted pressure oxidation pilot plant studies at Hazen Research, Inc. on the Twin Creeks refractory carbonaceous gold ores during 1993 and 1994. Previous laboratory investigations demonstrated very good gold recoveries of 90 to 95%, using CIL cyanidation after batch pressure oxidation. However, results from the pilot plant showed that several ore types responded very poorly, with gold extractions of only 45 to 75%. Since these poor recoveries were unexpected, pilot plant testing was suspended for approximately four months while extensive research activities were conducted to determine the cause(s) and identify potential solutions. This paper describes the batch and pilot plant test results, the research activities that eventually identified the cause of the gold recovery problem, and the final semicontinuous and continuous pilot plant operations that confirmed possible solutions.

Jan 1, 1997

By L. S. Gertsch, M. Z. Abu Bakar

The research presented here is part of a project to quantify the differences in the mechanical excavatability of rocks in dry and water-saturated conditions. A series of full-scale laboratory linear rock cutting tests were carried out with a long-bladed single disc cutter on dry and water-saturated sandstone blocks. The muck collected from the cutting tests was analyzed to establish a link with the specific energy (SE) of the operation. The coarseness index (CI), a non-dimensional parameter, was found to be a useful indicator of the relative efficiency of the cutting operation. An inverse relationship of the form SE = k CI-n was observed between SE and CI. The power n of the relationship for both dry and saturated rock was much lower than found in previous studies. The exponent n is believed to be dependent on the strength of the rock and the cutter type used. Although the average CI was lower for saturated rock than for dry rock, at the same time, saturated rock cutting was found to be less energy-intensive (in terms of SE) than dry rock cutting. Moderate correlation exists between the production rate or yield and the SE of the cutting operation for both dry and saturated rock, which can provide some useful information about the field production rate, discounting the effect of discontinuities in the rock mass.

Jan 1, 2012

By PDF

Flotation columns are widely used in mineral processing and coal preparation industry today. Mathematical modeling of flotation columns has conventionally been done using axial dispersion or tank-in-series models. However, for design and scale up purposes these models are not adequate enough because they do not provide detailed information of the flow fields within the column. This paper presents a Two-Dimensional, Two-Phase. Fluid-dynamic Model and its numerical solutions for some cases encountered in column flotation. The MAC (Marker and Cell) method was employed to obtain the numerical solutions, and based on this method a computer code COLUMNFLOW was developed. The simulated flow field reveals the presence of a circulation flow structure in flotation columns, which could be one of the main reasons for mixing in column flotation. The effects of some parameters such as superficial gas and liquid velocities on the characteristics of the flow structure in flotation columns were also tested with the numerical model.

Jan 1, 1994

By M. S. Prasad

In earlier work it has been shown that paper filler clay products can be obtained from primary kaolin deposits of Minnesota. The objective of the current work was to reduce silica and iron contaminants and to maximize kaolin recovery to higher value products suitable for paper coating. This results in achieving a finer and cleaner product conforming to paper coating specifications. Cationic flotation and high gradient magnetic separation were used to remove free silica and iron, respectively, while attrition grinding and ultrasonics have been examined for particle size reduction. The results of this work are presented and discussed particularly with respect to application-oriented product properties. Budgetary estimates are presented for a 200,000 ton/year processing plant based on the process flowsheet developed and optimized by the study.

Jan 1, 1991

By M. E. Kuchta

Surface coal mine design can be facilitated with the use of an interactive graphics personal computer program. This mineral inventory and planning program (POLY CALC) is described and its use is illustrated with a case study. The case study deals with investigating a stripping sequence and associated dragline stripping requirements.

Jan 1, 1986

By H. K. Lin

The free-milling ore characteristics of the Fort Knox gold deposit are ideal for studying gold and silver behaviors in various processing circuits without serious interference of sulfide minerals and other refractory factors. A galvanic effect leads to faster silver dissolution than gold dissolution and, as a result, the Au/Ag solution concentration ratio increases through the leach circuit. In the CIP circuit, Au adsorption is more effective than Ag adsorption. The Au/Ag solution concentration ratio decreases from 10.0 to 1.0 as the slurry advances from CIP tank #1 to CIP tank #5, while Au/Ag ratio in the carbon increases from 3.2 to 15.3, as the carbon advances from CIP tank #5 to CIP tank #1. Silver is stripped more effectively than gold from the loaded carbon. The Au/Ag ratio in solution reaches 2.0 in the first 75,700 L of strip solution that pass through the loaded carbon; as the stripping process continues, the Au/Ag ratio in the strip solution increases. In the electrowinning circuit, the Au/Ag ratio in the spent electrowinning solution is significantly lower than that in the electrowinning feed, indicating that Au is more rapidly deposited onto the cathode than Ag.

Jan 1, 2010

By J. S. Lee

Alkyl hydroxamates are well known collectors for oxide copper minerals as evidenced by the large amount of published literature. Our studies on a wide variety of copper ores from around the world have shown that alkyl hydroxamates will recover most of the "floatable" oxide copper minerals from an ore. They are available commercially, and they offer many advantages over alternative technologies for oxide copper recovery. In spite of this, the full potential of hydroxamates has not been exploited in the industry. The objective of this paper is to provide relevant practical aspects and guidelines to facilitate successful application of hydroxamates in operating plants. A critical analysis of the available information and data, based on several case studies, notation testing, and microscopic analysis indicates that alkyl hydroxamates can effectively recover well-defined oxide minerals of copper, but not copper occurrences such as Cu-bearing goethite (often misidentified as cuprite) which report as Acid Soluble copper in chemical assays. Prior to any notation testing with hydroxamates, it is necessary to assess the various modes of occurrence of Acid Soluble copper using microscopic and microprobe analysis.

Jan 1, 1998

By M. G. Ayat

Coal degradation is the breakage of coal particles to finer sizes due to the continuous forces of attrition and gravity to which coal is subjected during mining, handling and preparation. The objective of this paper is to determine the extent of degradation that a coal slurry experiences when transported through pumps and pipelines. The examination of degradation results for a number of different coal slurries have indicated that the extent of breakage is dependent upon the physical properties of coal and the time span of circulation. These results have also indicated that certain size fractions of coal are more susceptible to breakage than others.

Jan 1, 1986

By Robert Moore Lewis

Extensive exploration is being undertaken throughout the world in search for heavy minerals, particularly rutile and other titanium minerals. The federal government is sponsoring research involving rutile ores and recovery of stockpile-grade concentrates from domestic sources. Producers are being forced to turn to deposits with a heavy mineral content as low as 0.50% (essentially rutile and zircon). The North Carolina State University Minerals Research Laboratory investigated the possibilities of recovering heavy minerals from the amine tailings of the Texasgulf Inc.'s phosphate plant at Aurora, North Carolina. One laboratory beneficiation procedure using gravity, electrostatic and magnetic processes, resulted in the recovery of 78.7% of the heavy minerals in the amine tailings. Based on this percentage recovery and the present rate of phosphate mining, approximately 13,000 tons per year of heavy minerals (principally ilmenite and zircon) with a potential value of approximately $1,045,000 (1977) could be recovered. The economic potential for recovery of these heavy minerals appears to be favorable. A flotation procedure for up-grading the heavy minerals content in the amine tailings has been developed at the Laboratory, which could allow for concentration of heavy minerals and storing them in tailings area other than main tailings for future processing.

Jan 1, 1978

By Lana Alagha, Ashraf Alsafasfeh, Amal Al‑Hanaktah

As freshwater resources are becoming scarce, the use of seawater as replacement of fresh water is appealing in order to make mineral processing operations more sustainable. Since froth stability plays a critical role in determining the performance of flotation operations, there is an urgent need to study the effect of frother dosage and seawater on froth stability. In this study, flotation tests in seawater were conducted to examine the effect of frother’s dosage (MIBC) on the froth stability and flotation performance of low-grade phosphate ore. The stability of the froth layer was assessed by measuring the froth growth velocity and the froth maximum height at equilibrium. Results indicated that the best flotation performance was obtained at 75 g/ton of MIBC where ~ 90% of phosphate minerals were recovered. At this recovery value, the concentrate grade was determined to be ~ 70%. Results from froth stability experiments showed that the stability of the froth layer increased by increasing MIBC dosage. At MIBC dosage of 75g/ton, the calculated values of dynamic froth stability and the froth height were ~ 0.4 cm/sec and 16 cm, respectively.

Jan 17, 2024

By S. K. Jena, S. Singh, B. Das, N. Dhawan, P. K. Misra, D. S. Rao

"Iron as an impurity in pyrophyllite ore affects pottery, ceramics and tile quality. We carried out the characterization of a pyrophyllite ore sample using optical microscopy, scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and wet chemical analysis. The study revealed the presence of 2.15% iron oxide (Fe2O3 ) along with silica and alumina as the major components, which constituted around 90% of the total sample. We carried out the removal of iron from the pyrophyllite using magnetic separation and acid leaching and found that wet high-intensity magnetic separation (WHIMS) could remove 28% of iron values while oxalic acid leaching could remove up to 99.3%. The leaching kinetics of iron removal and the effects of pulp density, acid concentration, leaching time and temperature were also investigated. The optimum conditions for leaching were found to be leaching time of 60 minutes, temperature of 90°C, pulp density of 5%, oxalic acid concentration of 0.3 M, and particle size below 100 microns. Iron dissolution from the pyrophyllite sample can be best described by the diffusion of ions through the product layer of constant-size spherical particles. The breakdown of the pyrophyllite structure was evident from the FTIR and TGA studies. The activation energy of the leaching process over the temperature range was calculated to be 43.47 kJ/mol. IntroductionPyrophyllite is a naturally occurring phyllosilicate mineral composed of aluminum silicate hydroxide [Al2Si4O10(OH)2] as the major component and often associated with other minerals such as kaolinite, mica, quartz, rutile and epidote. It occurs in fine-grained sericite schist that is quarried as pyrophyllite (Pandit et al., 2008). In India, pyrophyllite occurs mainly in Madhya Pradesh state, Uttar Pradesh state and the Keonjhar district of Odisha state (Harpavat, 1995). Pure pyrophyllite is a highly desirable material for various applications due to its unique properties. It exhibits high refractive behavior, low thermalelectrical conductivity, low expansion coefficient, low hot-load deformation, low bulk density and high corrosion resistance to molten metal and basic slag (Rieger, 1997). It is used in the ceramics, refractory, foundry, electrical-insulation, sanitary-ware, glassmaking, pesticide and rubber fields. Compared with clay, it has lower thermal conductivity and coefficient of expansion, making it more suitable for refractory applications (Harben, 2002; The Minerals Yearbook, 2011)."

Jan 1, 2015

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

"The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities (82%) may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis. Among coal and rock dust exposure, high noise levels, roof and rib falls, and the potential for fires and explosions, operating and working with heavy machinery poses a significant risk to miner safety. One of the most hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 39 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are now required on all operating CMMs in underground coal mines with the exception of full-face CMMs [1]. Commercially available proximity detection (cPD) systems are based on the principle of magnetic flux density (B-field). Typically, four magnetic field generators are positioned on a CMM, and personal alarm devices (PADs) are worn by the miners that detect magnetic flux density difference. As a miner wearing a PAD gets closer to the machine, the flux density increases. Zones can be constructed around the machine so that an alarm will trigger on the PAD based on the flux density."

Jan 1, 2016

By J. S. Chung

As part of ongoing deep-ocean mining research, hydraulic transport systems as well as status of deep-ocean mining systems are reviewed in the aspects of manganese nodules and crusts from 800-6,000-m depth. The emphasis of the investigation of hydraulic transport is placed on the shape effect of particles on the pressure gradients and flowrates. Series of tests are being conducted to study the lift characteristics of a 2-phase vertically upward hydraulic transport of 2 types of small solid particles in a PVC pipe of 1-in (2.54 cm) diameter: irregular-shaped silica sands and equivalent spherical glass beads. Pressure drops and mass as well as volumetric flow rates were measured by electromagnetic (EM) flowmeter and mass flowmeter. The particle sizes used are 8-10 mesh. The results in turbulent flow range of 104 < Re < 105 show that pressure gradients or friction factors are smaller for the spherical beads than the sands. The larger the concentration of the particles are, the larger the pressure gradients become. The larger the particle concentration is, the less the effect of particle shape on pressure gradients becomes. The shape effect is greater for the minimum particle transport velocities than for the settling velocities.

Jan 1, 1999

By D. A. Peterson

A research program is currently in progress at the University of British Columbia to determine the potential of composite cable bolt reinforcement in Canadian mines. Several prototypes of glass fibre cable bolts have been tested. Their evaluation consisted of lab testing at the University of British Columbia, United States Bureau of Mines (Spokane) and trial installations at Detour Lake, Winston Lake, and Myra Falls Mines. A market analysis of cable bolts within the Canadian mining industry has been completed. Fibre reinforced polymer composites have a high potential as cable bolt reinforcement in mining applications. They prove to be a viable alternative to steel cable bolting.

Jan 1, 1993

A coal mine located in southern West Virginia recently set a world record for daily low-seam coal production using a Cat automated longwall plow system. In a 24-hour period on April 10 and 11, 2014, the Pinnacle Mine longwall produced 32,411 t (35,724 st) from the Virginia Pocahontas No. 3 Seam, in a seam height of just 1.42 m (56 in.) along the 298-m (980-ft) longwall face. The Pinnacle Mine, located near the town of Pineville and owned by Cliffs Natural Resources Inc., an international mining and resource company, operates a Cat Gleithobel GH1600 Longwall Plow System. A previous record was set by this system at Pinnacle in August, 2012 when 29,423 t (32,430 st) were mined in a 24-hour period. The record was set by the same system, mining its second panel after a comprehensive rebuild was performed by Carter Machinery, the Cat Dealer in that area. The rebuild encompassed a complete rebuild of the headgate and tailgate armored face conveyor (AFC) drive, the headgate and tailgate special AFC pans, the stageloader drives and return end, the complete crusher and all gearboxes for the plow, AFC and stageloader. Carter acquired the rights to sales and aftermarket support associated with the former Bucyrus mining products, both surface and underground, in 2013. ?Supporting and rebuilding a longwall plow system was a new experience for the Carter service team,? said Chris Curfman, president of Caterpillar Global Mining Sales and Support Division. ?However, given the record production results attained by the rebuilt system at Pinnacle, it?s obvious that they are up to the challenge of supporting the underground product lines at the same high standards and quality level that they have been delivering for many years on the traditional Cat surface mining products.? Tom Bluth, president of Caterpillar Global Mining Products Division, said, ?Caterpillar congratulates the Pinnacle team for this great achievement. Without their efforts and dedication this record would not have been possible. To safely deliver that kind of output from such a thin seam is remarkable. We have been privileged to work alongside their team to demonstrate the capabilities of Cat longwall mining technology. ?

By S. Garcia

The Minera Yanacocha operation presents various operating challenges, due to the complex structure of several heaps interconnected with ponds and gold recovery plants. A comprehensive process model has been developed in order to better understand the effects of certain operating parameters on issues such as water usage and inventory. An integral component of the water/mass balance of the process is a model of each heap that describes the flow and chemical behavior based on the individual characteristics of the heap. A computational fluid dynamic (CFD) software framework is used to model the individual heaps. The structure, calibration and validation of the model are described. Several examples demonstrating application of the process heap model are presented for the La Quinua heap. The effects of loss of solution flow to the heap (i.e., pump failure), increased cyanide levels in applied solutions and higher copper head grades on the process operation and balance are investigated with model simulations and compared to the baseline operating conditions. An example of estimating gold production and inventory based on projected heap loading plans is provided.

Jan 1, 2010

By D. R. Taylor

The use of clay granules as carriers for pesticides dates from the early 1940&apos;s and by the present day represents a business conservatively estimated at between 200 -300 thousand tons / year in the U.S. alone. Aside from economic and specific target pest efficacy advantages, the use of clay granules as pesticide carriers also delivers a number of environmental benefits which will be reviewed. Topics to be discussed will include: I) drift control (versus liquid sprays), 2) mobility (in the environment), 3) worker safety, and 4) transportation (spill) safety.

Jan 1, 1999

By Tsunenori Shibata, Kazunori Jimbo, Kaoru Toya, Masafumi Matsumoto, Jinya Mitsui, Toshinori Tsuji

"The Toyama Line is under construction as a natural gas pipeline with a length of 102 km from Itoigawa City to Toyama City. A 2 km-long tunnel section of the pipeline that we are reporting here is being excavated in a mountain area away from an urban area. The geology under which the tunnel is constructed is collapsible fractured breccia slate and Holocene sandy soil. Other tunnels of the Hokuriku Expressway and Hokuriku Shinkansen are in service above the tunnel route. From the starting shaft on Toyama side, conventional tunneling was adopted to facilitate excavating the base rock layer and maintain enough distance from the Hokuriku Expressway tunnel. From the starting shaft on the Itoigawa side, TBM tunneling was adopted to cope with the unconsolidated soft ground for a 200 m-long section from the shaft. We will discuss the issues and countermeasures concerning the selection of a tunnel route and excavation methods, performance of both conventional and TBM tunneling, and underground connecting of these tunnels excavated by conventional (NATM) and TBM methods under a high groundwater pressure up to 1.2 MPa. INTRODUCTION AND BACKGROUND The International Petroleum Exploration Teiseki Co., Ltd. (INPEX) is constructing a high-pressure main pipeline network in the Toyama Prefecture area to promote the use and reliable supply of natural gas as shown in Figure 1. As part of the Toyama line project that has a total length of 102 km, A-1 construction, the nearest section to the tunneling starting point in Itoigawa City, where various tunnel excavation methods have been adopted to install the high-pressure pipeline 20 inches in diameter, a 2 km tunnel in the A-1 construction section discussed here is to be excavated by conventional and TBM methods in a mountain area. Based on environmental studies such as traffic jams due to frequent traffic of heavy vehicles disposing of soil, and the effects of dust, noise and vibration during construction, we selected the route to install the gas pipeline in a mountain area as shown in Figure 2, where the impact on the surrounding environment could be minimized."

Jan 1, 2016

By J. O. Marsden, J. H. Gourdie, J. R. Arnold, J. G. Mansanti

During the testing and design of the Gold Fields&apos; Chimney Creek mine, it was found that a much higher carbon loading was possible with CIC (carbon-in-solution columns) than with CIP (carbon-in-pulp). In an effort to keep the carbon handling minimized, an emphasis was put on forcing gold to the CIC circuit rather than the CIP. After considerable study, it was found that a circuit with two thickeners and an interstage leach would force 90% of the gold to CIC. Computer modelling indicates that the benefits of the hybrid circuit include higher recovery, less carbon handling, fewer leach tanks, and lower reagent costs.

Jan 1, 1990

By LaPoint D. J.

Copper deposits in sandstones are excellent targets for open pit mines using SX-EW extraction and processing methods. The mineralogy consists of chalcocite as the primary sulfide and copper carbonates and sulfates in the zone of oxidation. Two general deposit types are recognized: early diagenetic copper deposits that are associated with the reddening of the surrounding sediments, and epigenetic deposits that are associated with the migration of copper-rich basinal fluids along faults into permeable reservoir beds with a source of reductant. Epigenetic copper deposits are more likely to contain enough tonnage to be economic.

Jan 1, 1996