Search Documents

By Dolf Vos

The balling section of the pelletizing plant at Hoogovens IJmuiden consists of 7 balling drums. Each with an average capacity of 100 tons of green pellets per hour. The balling drums are equipped with rotating scrapers and water-spraying systems. The scrapers are installed in order to restrict the growth of the race to a certain thickness. The spraying system is used to adjust the desired value of the moisture-content of the rewetted ground ore, the pellets and the race. The desired value is the value by which the balling- process is stable, good pellets are formed and surge occurs within certain limits. In October 1980 the construction of one of the balling drums has been modified. The rotating scraper was removed and the inner wall of the drum was supplied with a rubber-lining. In 1982 a second balling drum has been rubber- lined. At the same time the Tyler vibrating screen of this balling circuit has been replaced by a roller(bed)screen. By the end of 1983 all 7 balling circuits will be equipped with rubber-lined drums in combination with roller(bed)screens. The combination of these two modifications will improve the quality and the screen analysis of the green pellets, moreover resulting in savings on energy- and maintenance costs. This paper describes the influence of a rubber- lining on the balling process and the green pellet quality by carrying out in-plant testruns in November/December 1980. The testrun results have been compared with the results of a not modified balling drum.

Jan 1, 1983

By Meghan M. Murphy, Derek Penrice

The Downtown Rail Extension (DTX) is principal element of the planned second phase of the Transbay Joint Powers Authority’s (TJPA) Transbay Program. When complete, this regionally critical project will connect Caltrain’s regional rail system and the California High-Speed Rail Authority’s statewide system to the Salesforce Transit Center in downtown San Francisco via a 1.3-mile tunnel. Studied since the 1970s, the DTX has now received environmental clearance, and key stakeholders are aligned on the project’s configuration and its expedited delivery. This paper describes efforts to optimize the DTX configuration and develop an informed project delivery strategy that incorporates construction industry feedback on project phasing, contract packaging, and procurement methods that accomplish the project’s budget goals.

Jun 13, 2021

By R. A. Haney

The Mine Safety and Health Administration (MSHA) has conducted studies both in coal and noncoal mines to evaluate methods for sampling and separating diesel particulates from mineral dust aerosols. The agency is investigating size separation techniques to distinguish between diesel particulate and respirable coal mine dust. Additionally, ashing techniques have been used to distinguish diesel particulate from mineral dust in metal and nonmetal mines. As part of these studies, personal exposures to diesel particulate for various mining occupations have been measured. This paper describes the measurement techniques and summarizes the exposure levels for various underground mining operations.

Jan 1, 1990

By J. D. Miller

The recent non-equilibrium electro-phoretic mobility measurements by laser-Doppler electrophoresis coupled with the stability and prevalence of collector colloids in soluble salt flotation systems suggest that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by hetero-coagulation. Previously reported flotation results confirm this surface charge/collector colloid adsorption model. However, the nature of the inter-particle forces responsible for hetero-coagulation of such oppositely charged particles at high ionic strengths remains to be determined. In this regard, atomic force microscopy was used for inter-particle force measurements at high ionic strengths. Model systems such as polystyrene/quartz and silica/sapphire were studied to measure the particle interaction forces prevalent at high ionic strengths. Results from this study indicate that while repulsive hydration forces exist between similarly charged hydrophilic particles, attractive forces exist between oppositely charged hydrophilic particles in high ionic strength solutions. The repulsive forces between similarly charged hydrophilic surfaces at high ionic strengths (2-4 M) are described by a double exponential function with decay lengths of 0.17 and 1.4 nm depending upon the surfaces involved. On the other hand, attractive forces were observed between oppositely charged hydrophilic surfaces at high ionic strengths (2-4M) and were described by a single exponential function with decay lengths of up to 9 nm depending upon the surfaces involved.

Jan 1, 1996

By M. Guzman, S. B. Thais, M. F. Obispo, M. R. Arribasplata

One of the greatest environmental issues related to the development of the mining activity is the generation of Acid Mine Drainage (AMD). Many methods have been developed for AMD treatment, being wetlands a good option for heavy metal removal. In this sense, the implementation of artificial wetlands for the treatment of mining effluents would seem to be an environmentally friendly alternative. In this paper, we present the results on the elimination of heavy metals (Cu, Zn, Pb and Fe) using two Peruvian native species such as Schoenoplectus californicus (C.A. Mey.) and Phragmites australis (Cav.) Trin. Ex Steud. The results show that Schoenoplectus californicus preferentially removes copper (82 and 90%), lead (88 and 92%) and iron (28 and 69%), whereas Phragmites australis removes copper (68 and 87%) and zinc (53 and 95%). Likewise, it is observed that the Schoenoplectus californicus mainly retains the ions in its root, copper (89%), zinc (84%) and iron (76%). While the Phragmites australis accumulates iron (62%) and copper (74%) in the steam and root part respectively

Mar 2, 2022

By James E. McNulty

The planning and development of new coal mines is requiring the increased use of geologic, geologic engineering and hydrogeologic investigations. This is caused in part by the fact that new mines must deal with less favorable conditions than existing mines as well as higher costs of development and in part by the dictates of regulatory authority. High costs of new mines require greater reliability of geologic assessment using best available geotechnical and geophysical methods and technology. Although the increased cost of additional subsurface data is significant, the more important factor may be the impact on project lead time.

Jan 1, 1981

By Jr. Chesson

"Phosphate" is a misnomer as often used. The word is increasingly used to refer to any material containing phosphorus - an element essential to any form of life. Phosphate rock, a mineral - fluorapitate - is recovered from Florida's sedimentary deposits in particle sires ranging from 0.1 to 13.0 millimeter. This product of mining, washing, screening, and flotation is commonly called "phosphate". Its phosphorus content, measured and reported as P2O5, varies from 29% to 35%, and is essentially insoluble. "Phosphate" is also used to describe products containing soluble phosphorus obtained from acidulation of phosphate rock with mineral acids; primarily, sulfuric acid. Many miners have nearby chemical plants wherein phosphate rock is converted into upgraded products such as phosphoric acid, superphosohates, and ammonium phosphates with 45% to 70% P205, soluble and suitable for use as fertilizer. The rock and upgraded products are all commonly called "phosphate"; the plants, "phosphate plants' and the producers collectively are known as the "phosphate industry". The public in Central Florida generally loses identification of the individual operators that include major corporations such as IMC. Williams Companies, W.R. Grace, Mobil, Embark, U.S. Steel, Borden, American Cyanamid and others. They all become just a "phosphate company".

Jan 1, 1978

By David A. Fawcett

An auxiliary cross-pit mining system, working in tandem with the prime excavator, is evaluated technically, operationally and economically for application in the selective removal and replacement of soils and unconsolidated ovezburden. Previous studies on cross-pit technology and applications of this technology are briefly reviewed. Stratigraphy plus pit, operating and economic parameters are assumed and applied in the evaluation and comparison of a base case dragline system with two alternatives - a dragline/scraper-dozer combination and a drag- line/cross-pit system combination. The economics of the proposed cross-pit system favour it as a viable alternative to conventional systems.

Jan 1, 1981

By Omar A. Muhtadi

Brohm Mining Corporation, in conjunction with Geobiotics, Inc. has nearly completed a pilot heap biooxidation test on sulfidic ore from the Gilt Edge Mine near Rapid City, South Dakota. Some results from the pilot testing have shown the correlation between the extent of biooxidation and the increase in cyanide gold recovery seen in the laboratory. Bench scale testing showed approximately a 1: 1 correspondence between percent biooxidation and percentage increase in gold recovery. The economics of large scale biooxidation were also evaluated in terms of increased gold recovery versus the time and cost of biooxidation. In the pilot test, the rate of biooxidation became limited by the acid water neutralization system. Later in the test, measures were taken to overcome this problem. Results from bench scale column bioleach testing showed that the Gilt Edge sulfide ore is quite amenable to biooxidation with a substantial increase in gold recovery with just partial biooxidation. Direct cyanide gold recovery of 51 % on ore crushed to -3/8" was enhanced to 82-85% after oxidation of37% of the sulfide as measured by iron. Laboratory experiments also showed that the slow rate of biooxidation of this ore could be accelerated by removal of metal sulfate build up from the leach liquor. The combination of these normally non-toxic metals became inhibitory to biooxidation if not removed by the neutralization circuit.

Jan 1, 1995

By P. R. Taylor

A reaction is evaluated by which heated and pressurized water is used to precipitate metal oxides from loaded Kelex 100 complexes. Pure copper oxide (CuO) and pure nickel (Nio) in powder form, and ranging in average size from 12 to 25 micrometers, were found to precipitate from copper and nickel loaded Kelex 100/kerosene complexes, by water heated and pressurized to between 374 and 400 °c and 2170 psig (148 atm) and 3500 psig (238 atm). The precipitation is suggested to result from hydrolysis of the metal, following exchange for the hydrogen in the phenolic hydroxyl of the Kelex 100 structure, enhanced by the conditions provided by heated and pressurized water. The reaction is believed to have the characteristics of homogeneous nucleation and heterogeneous growth. The effects of temperature, pressure, initial metal concentration and seed addition on the kinetics of the process were studied. In addition, characterization studies were performed on the reaction products. A detailed discussion of the experimental results is presented.

Jan 1, 1992

By Ilmar J. Martens

The statistical information and cost data used in this report has been made available by NICKDATA INC. Since 1982, NICKDATA INC. of Toronto, Canada, has produced an annual comprehensive nickel industry cost study. Up to date information on 22 mines, 21 smelters, and 16 nickel refineries representing 30 nickel production operations in 17 countries are included in the computerized cost analysis. The report is compiled from information obtained through regular annual visits to major nickel operations and continuous monitoring of information on all nickel producers. The 1984 report which was completed this summer, reveals drastic changes in the nickel industry cost structures.

Jan 1, 1984

By G. A. Calboreanu

The deterioration rate of any metal or alloy is increased in a erosion-corrosion application because the passivated surface layer is removed by the solid particles contained in the pumping fluid and the material surface becomes corrosion active again. Numerous attempts were made to engineer a stainless steel with higher hardness and unaffected corrosion performance. Alloys of special interest in such an area are the duplex stainless steels particularly the CD4MCu material which has the capability of being hardened due to its ferrite-austenite microstructure. Unfortunately, the CD4MCu with higher hardness comprises different intermetallic compounds which will increase the corrosion rate. The paper is analyzing the erosion-corrosion performance of a new type CD4MCu with 32% higher hardness and superior wear performance. The corrosion performance of this new alloy is better than the corrosion performance of the common CD4MCu material which the industry could supply. The corrosion effectiveness was evaluated with the Huey test, the potentio-dynamic anodic polarization test and the weight loss test whereas the erosion resistance was established with a low stress ball-on-disk type apparatus. The Wilfley hard CD4MCu material had 39% lower weight loss and 32% smaller volume loss than the common CD4MCu alloy The hardness range of the centrifugal pump parts poured and processed with the Wilfley hard CD4MCu is 320-350 HBN versus 250-255 HBN hardness of the common CD4MCu. After approximately 18 months of experimentation and field testing it was clearly established that the life time of the Wilfley hard CD4MCu is higher than the common CD4MCu and consequently centrifugal pumps were supplied to different customers in North and South America. India and more recently Australia. Sincere thanks to all the A.R. Wlifley & Sons Inc. and Western Foundries Inc. employees who supported and help to implement this work. special thanks to George Wilfley. Dave Cobb. Bill Becker Sr. and Wayne Taylor

Jan 1, 1997

By W. G. Fischer

Trona ore at the Westvaco mine of FMC Corporation has been obtained by room- and-pillar methods since the mine began operation. The flat-lying, 10-foot bed of trona, Na2CO3 NaHCO3 2H2O, is covered by 1500 feet of weak shale and sandstone. Extraction of pillars on the retreat quite often throws large amounts of weight onto development workings. Weak shales in the roof and floor fail rapidly and the mine ribs slough to such an extent that mining often becomes very difficult. When this occurs efficiency goes down, costs go up, and the risk to men and machinery increases greatly. Difficult mining conditions in the early 60's forced a re-evaluation of all presently known mining techniques in bedded deposits. Many room-and-pillar mining plans' were compared with the system in use at that time, but none of them offered a better solution to the roof control problem. Longwall techniques were seriously considered, but machinery was not available that would cut the hard trona seam and still maintain the productivity obtained from room-and-pillar sections. Roof cones troy in the longwall methods appeared to be more satisfactory than that found in room-and--pillar techniques. It was therefore felt that a new technique using the longwall principle and based on rock mechanics should be tried rather than previously known pillaring methods.

Jan 1, 1966

By R. S. Datta

Regulations on sulfur emissions have caused the electric utilities to evaluate various methods of meeting them. Low-sulfur, low-volatile coals can be burned alone or blended with high-volatile? coals. This option may be a cost-effective alternative to the installation of scrubbers on coal-fired combustion systems. In some blending applications, problems may be encountered because the low sulfur content and high calorific value of the low-volatile or other clean coal allow it to economically upgrade extremely poor quality coal. While this is done to meet specification purposes, actual boiler performance may be dominated by the poorer quality coal. Thus, the reputation of the low-volatile or other clean coal suffers. As a result of laboratory and full scale testing, conducted over the last five years, a model has been developed to evaluate the relative combustion characteristics of various coals and coal blends. A database for different coals has been gathered. This paper presents the model and shows how power plants and coal mine personnel can use it to evaluate their coals from different sources. It can be used to blend two or more coals from different sources so that thee blended coal has flame stability characteristics which are similar to those of the baseline coal.

Jan 1, 1991

By Siyu Song, Yanhong Wang, Guohua Gu, Linbo Huang

In this study, the effect of cations, Na+ and Mg2+, in saline water on copper flotation in the presence of calcium bentonite was investigated. It was found that as the concentration of NaCl was increased, the copper recovery initially decreased and then increased to above 99%, while the copper grade initially increased and then decreased. In contrast, as the concentration ofMgCl2 was increased, the copper recovery continuously increased, while the copper grade continuously decreased. The variation of copper recovery and grade was mainly attributed to the synergistic effect of pulp rheology and flotation solution chemistry. The underpinning mechanisms are the compressing electrical double layer and ion-exchange interaction between saline water and bentonite, which occur at the same time. Using salinewater slightly affected the pulp rheologywith a decrease in copper recovery at low NaCl concentration. Increasing the concentration of cations in saline water might even facilitate the flowing out of exchangeable cations, especially divalent cations, from the interlayer space of bentonite to the solution, resulting in the decrease of copper grade at high salt concentration.

Sep 10, 2020

By Hesam Dehghani, Farid Alimohammadnia, Nima Babanouri, Mokhtar Kalhori

In open-pit mining, blasting pattern design is performed to achieve a desired degree of fragmentation for loading, hauling, and crushing operations. Inappropriate fragmentation of rock will result in numerous problems such as incurring extra costs for secondary blasting, production interruption, etc. Wetness of the blast holes is one of the most important factors, which can cause the inappropriate rock fragmentation. Lowering ambient temperature in the vicinity of the explosion, the presence of water in the hole adversely affects the quality of the explosive while dissipating part of the explosion energy, ending up with inappropriate fragmentation problems. In the present research, in order to study blast-induced fragmentation conditions in Baba-Ali Iron Ore Mine, three scenarios were considered: explosion of ammonium nitrate with fuel oil (ANFO) in dry hole, explosion of ANFO in wet hole, and explosion of the emulsion in wet hole. For this purpose LS-DYNA, a numerical simulation code was used. Results of the present research showed that, compared to the explosion of ANFO in wet hole, the explosion of the emulsion produced more uniform distribution of fragment size, while the explosion of ANFO in dry hole resulted in fewer large fragments.

By Jr. Smith

Silver-gold ratios were studied at the Tayoltita epithermal vein deposit using channel sample, channel sample line, stope, ore body and vein sample populations. The ratios are highly variable among individual channel samples (25:1 to greater than 500:1) with both high and low values randomly distributed within ore bodies and veins. Whole vein ratios for the fourteen most important ore producing structures range from 44:1 to 105:1, and show zonal distribution relative to two small granitic stocks, low values closest to the intrusives. The zoned nature of the deposit suggests that the stocks, apophyses of an underlying batholith of Late Eocene age, were the heat engines which powered the hydrothermal system responsible for ore deposition.

Jan 1, 1978

By Atmesh K. Sinha

Death and injury rates in mining have been the highest of any industry; the injury severity rates in mines have also been the highest. Tentative figures reveal that 1971 was the best year yet for the bituminous coal indus¬try with the lowest number of fatal accidents. Nevertheless, 177 men were killed at a frequency rate of 0.76 per million man hours. Coal mine accident statistics have been described at various times as unacceptable and intolerable and recently resulted in the enactment of massive legislation. The 1969 Coal Mine Health and Safety Act was passed by Congress "to improve the working conditions and practices in coal mines and to prevent accidents and occupational diseases originating in the coal mining industry." The prevention of accidents in coal mines is the statutory responsibility of mining engineers and the moral responsibility of all who have any part to play in mining coal. The questions to be answered by these men may well be - What are the reasons for the high accident rate? Are the mines as safe as they can be? Are our mines sufficiently manned to insure proper supervision of production cycles and safety requirements? Are our plans for safety committees, safety campaigns, and safety inspections sufficient? Are they producing the results intended? If not, how can these be reorganized to have a greater impact? What is the real cost of an accident? What are the immediate and long-term plans for further improvements? These questions are in no way exhaustive, and the answers are not easy. There are many aspects of mine safety, and any one of them can be the subject of a lengthy discussion. The aim of this paper, therefore, is to limit the analysis to documented fatal electrical accidents in mines so that meaningful conclusions for improvement in electrical accident-experience statistics can be made. In doing this, it is also the intention to emphasize areas of missing information and propose a few suggestions for better hazard analysis.

Jan 1, 1972

By W. Blake, J. Whyatt

Sixty years of rock bursting in the Coeur d'Alene district has taught painful lessons and led to a number of practical advances in controlling rock-burst hazards. This paper summarizes these lessons, concentrating on practical measures that have been successfully adopted to reduce hazards. These lessons are explained in the context of district mining history and current understanding of rock-burst phenomena. Overall, the paper provides the practicing mine engineer with an appreciation of rock-burst hazards and an overview of practical measures that can be used to control these hazards in the context of Coeur d'Alene district experience.

Jan 1, 2003

By Egon Pohl, Peter Eckl, Friedrich Steinhäusler, Johanna Pohl-Rüling

RADON EXPOSURE AND CARCINOGENIC CELL TRANSFORMATION The highest radiation burden to miners is due to inhalation of radon and its short-lived decay products. The quantification of the risk associated with this radiation burden is complicated by modeldependent lung dosimetry, insufficient accuracy of past human exposure data as well as lacking knowledge about potential synergism of various carcinogens. Nevertheless, it is evident from epidemiological studies of miners that inhalation of elevated levels of radon daughters is correlated with increased lung cancer incidence (UNSCEAR, 1977). The situation is further complicated by the lack of reliable data on the biological variability of the latency period for the development of lung tumor under varying exposure conditions. At present information on variation with age is scarce, however, it is indicated that the excess lung cancer rate for workers exposed to high radon levels is considerably higher, if exposure occurs at ages over 40 years as compared to under 30 years of age (Sevc, Kunz, Placek, 1976). Furthermore, latency period is shorter by 6 - 7 years for smokers exposed to elevated radon levels than for non-smokers (Fry, 1976). Analysis of US- and CSR-uranium miner data revealed that the mean latency period is in the order of about 15 years (Jacobi, 1973). These uncertainties, together with medical diagnostic shortcomings, lead to the dissatisfying situation that at present the detection of radon induced injury of mining personal is primarily the assessment of the endpoint, i.e. radiation induced cancerous transformation of lung cells with typically less than 10% chance for recovery. Therefore it would be advantageous to develop practically applicable diagnostic aids to indicate already early precancerogenic changes of cell characteristics. This would permit the identification of specific population groups at increased risk for the development of lung cancer, thereby increasing the chances of more successful medical treatment. Despite continuous improvements in the reliability of test methods for the diagnosis of cancer cells there is still need for techniques, which enable the detection of transformed cells before the onset of invasion of the host organism. It is generally recognized that the transformation of a cell into a malignant state leads to a change of the cell surface, indicating a correlation between membrane-specific immunological properties and loss of growth control. Surface alterations on cells appear to be responsible in part for the malignant state and are not simply secondary effects of the transformation (Schnebli and Burger, 1973). Furthermore, membranes of cancer cells differ significantly from those of normal cells, particularly, in permeability properties (Rastogi, 1976). In dying cells, proteins, glycoproteins, peptides, aminoacids and their breakdown products are released, which block the permeation of the membrane itself. A mammalian cell can be considered as a 3-phase system (interior, boundary, environment) with the membrane forming a heterogeneous barrier between two subsystems. Under normal circumstances a difference of chemical potential is maintained on both sides of the membrane, causing an ion gradient across and fixed surface charges on the membrane. This results in a membrane resting potential (MRP) between cytoplasm and the bulk medium. It has been shown that MRP is a highly sensitive indicator for cellular reactions due to physical, chemical and biological agents, particularly whenever phenomena of transport and ion gradients as well as permeability are involved (Redmann, 1980). The primary interaction of the agent "ionizing radiation" with any form of living matter occurs at the cellular level. The component with the highest hit probability is the cell membrane. In the study presented MRP-changes of human cells were investigated with simultaneous measurements during irradiation and post-irradiation intervals up to six days. Furthermore, the suitability of MRP-measurements of human cells was tested as an indicator for early changes of cellular properties prior to the histological confirmation of carcinogenic transformation. EXPERIMENTAL METHODS Lung cells The biological specimen used were cultured human lung cells and human lung biopsy samples. Monolayers of lung fibroblasts (W138) were grown in petridishes using conventional culture techniques. In addition, transformed lung cells (W138SV13, subline 2RA) were used applying similar culture methods. All petridishes were incubated at 37°C and only cells in logarithmic growth phase were used. Freshly excised lung biopsy samples were obtained from randomly selected male and female patients (20 cases), where suspected or unclear malignancies were indicated by clinical or X-ray observations. At the time of sampling 80 % of the patients were or had been smokers in the past. The samples were taken by means of a stiff bronchoscope introduced into the trachea under local anasthesia with 1 % Novesinsolution (preparation with Atropin and Pantopen). This permitted the observation of both main bronchi down to the segmental bronchials. From each patient two tissue samples were excised from the mucusepithelial layer under visual control with fiber optics and transferred immediately into 1 % NaClsolution. One sample was taken from the suspected

Jan 1, 1981