Search Documents

By J. D. Allen

The Concord Mine Coal Preparation Plant of United States Steel Corporation, located near Bessemer, Alabama, began operations in June, 1950. The basic cleaning circuit consisted of a Chance Cone for cleaning the 2-inch x 3/8-inch fraction and concentrating tables for cleaning the minus 3/8-inch coal fraction. Dewatering of the final product was accomplished with 35-mesh vibrating screens. However, because Concord coal is very friable (Figure 1), 85 per cent passing three mesh and 25 per cent passing 28 mesh, there was a considerable amount of fines passing through the dewatering screens. To recover these fines, the dewatering screen effluent was sent to two 70-foot diameter hydro-separators with the underflow returning to the dewatering screens and the overflow going to a 175-foot diameter thickener for water clarification, (Figure 2). As might be expected, there was a considerable amount of recirculation of the minus 35-mesh coal in this system. This degraded the coal and led to higher moistures. It also resulted in a fines bleed-off of plant water and thickener underflow to a fine-coal settling pond. In 1961, vacuum filters were installed to supplement the screens and to recover the fine coal lost in the bleed-off. The above system resulted in a product moisture of about 20 per cent. Further reduction to approximately 11 per cent was accomplished by drainage from railroad cars during transit to the coke plant. Control of the moisture at unloading was poor because of variations in operating levels and railroad car availability, but since the Concord coal constituted a smaller percentage of the coal previously used at the coke plant, the high moisture and fluctuations did not seriously hamper coking operations.

Jan 1, 1966

By P. Geoffrey Feiss

The Piedmont province of the southern Appalachians is becoming the focus of interest for many exploration geologists. In the past, only those deposits with significant surface exposure have been exploited. Thus, few deposits have been found and relatively little exploration has been conducted in recent years. Modern geochemical and geophysical techniques can alleviate this problem of concentrating on exposed ore bodies by allowing us to "look through" the soil and saprolite to detect the presence of significant mineralization at depth. This paper will attempt to evaluate the feasibility and effectiveness of several geo¬chemical exploration techniques in the Piedmont, of Cabarrus and Stanly Counties, North Carolina. The area chosen for the study is shown in Figure 1, lying almost wholly within the Mt. Pleasant quadrangle, North Carolina. The area is on the eastern boundary between the Charlotte belt, a zone of plutonic and intermediate grade metamorphic rocks, and the Carolina Slate belt, a series of complexly interbedded volcanic and sedimentary rocks of predominantly low grade metamorphism. The area is now considered to be a 500 million year old active, continental margin.1 As is typical of most of the piedmont, outcrop is sparse. Figure 2 is a sketch map of the general geology of the area under study, showing the Charlotte belt rocks in the northwestern quadrant and slate belt rocks, to the east. Within the area are a number of old mines and prospects, the most famous of which are the Furniss and the Phoenix mines in Cabarrus County. All are reported to have contained Au and Cu. Ag and Pb were reported from some. A summary of the deposits is given in Table 1. Data used in this study are from three Master's theses conducted at the University of North Carolina at Chapel Hill. 3,3,6 In separate studies, well waters5, B-zone soils3, and vein and float quartz6 from the area described were sampled and analyzed. Each study concluded separately that geochemical anomalies in the vicinity of the ores justify use of that specific sample type in a geo-chemical exploration program. However, no comparative study of the methods has

Jan 1, 1977

By P. Guliov

In the first part of this paper the authors present an overview of industrial minerals produced in the Canadian provinces of British Columbia, Alberta and Saskatchewan, and supplied to the Pacific Rim countries. The second part outlines some of the unique opportunities for industrial minerals that exist in the three western Canadian provinces and those minerals we feel have development potential for overseas markets. Because of time constraints, it is not an exhaustive presentation on industrial minerals, but is focused on a few selected minerals that we believe have high potential.

Jan 1, 1990

By William H. Breeding

The remarks that follow are based substan¬tially on experience covering 45 years, 80% of which have been in placer work, rather than on a review of available literature. Most commercial placers have been deposited by the action of water. The richer and more-difficult-to-mine placers are those in the headwater areas where gradients are steepest. The most lucrative placers are generally in intermediate areas where volumes are greater, fewer boulders are present, and gradients are from 3% to 1 ½ . The higher volume, lower grade placers are in the lower reaches of river systems where gradients are lower. Where gold-bearing rivers have discharged into the sea, wave action can concentrate values on beaches, past and present.

Jan 1, 1984

By Earl L. Rau

Although the Sagasca deposit has been known for 76 years, the property was never put into successful operation because of various adverse factors including low market price for copper, legal entanglements, unsuccessful financial arrangements, and an inadequate metallurgical process. Late in 1963, Continental Copper & Steel Industries, Inc., obtained legal control of this property. Since that time there has been a concentrated effort to complete the necessary mine appraisal, process development, and engineering design, and to solve the legal and financial problems to bring this property into production.

Jan 1, 1970

By Lauro Lacerda

Shotcrete is a highly adaptable and widely used underground construction material at infrastructure and mining projects around the world. In fact, many projects could not have been completed without its utilization. As underground projects became larger the use of mechanized wet-mix spraying gradually replaced manual dry-mix shotcrete applications. This paper details some of the reasons for that and provides information on the equipment and operational factors including safety and productivity required to successfully complete underground shotcrete projects.

Jun 13, 2021

By Sean Hunter

Artificial Intelligence has a long history but is currently coming strongly into focus with new advancements. This leads to questions many people are asking: what exactly is AI, how can it be used effectively in mining operations, and what foundation is required to make AI implementations successful? In mining, many AI applications exist, from drill pattern optimization to predictive maintenance. However, many implementations struggle due to data integration challenges. Mining operations generate large amounts of data from many sources, such as fleet management systems, drill sensors, process control systems, and laboratory results. Unfortunately, this data often exists in silos where it’s difficult to get it out, making AI applications unable to leverage it. Worse still, tools that use AI don’t always provide their data back to the system, creating even further data silos. All these problems make it hard to take advantage of the data at the mine, slowing down and reducing the effectiveness of AI. This paper presents a comprehensive approach to organizing mining data using an AI-ready knowledge graph system. We will first explore the evolution of AI in mining, from early expert systems to modern machine learning applications. Then, we will detail how a knowledge graph can integrate business context, operational data, and AI models into a cohesive system that enables more effective AI implementations across mining operations. The proposed method has been developed considering both the unique data challenges faced by the mining industry, while also considering best practices learned from the AI field at large. By following this approach, it’s possible to better utilize existing data, getting higher quality and more complete results faster, and in a way that’s reusable and composable.

Feb 1, 2025

By A. K. Bakshi

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle's Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

By R. H. King

Underground coal mining machinery utilizes portable electric sables, "trailing cables." to obtain power from load centers or distribution boxes. Cables are frequently damaged since mobile equipment, poor lighting, and restricted space are inherent to coal mining operations. Normally, the damage is repaired by splicing--the joining of one or more severed conductors and replacing insulation and jacket. Figure 1 illustrates a typical single conductor splice. Although the repair seems simple, difficulty of the splicing process is exemplified by the many safety hazards and frequent production delays that result from defective splices. Forty-two cable splice related injuries were reported to the U.S. Bureau of Mines in 1972 and 1973. Additionally, 17 splices related fires were reported in the three year period prior to December 1972. Assuming the damaged area is quickly located, an average splice time for a two conductor cable is twenty minutes. Some operators estimate this delay is incurred once per day per operating section. If one ton per minute is averaged throughout the shift, each unit could loose 4800 tons per year from splice delays. An estimated cost for materials and labor to make a splice is $20. The expenditure could result in a $4800 annual cost per section. The estimated expense does not include wages of other personnel waiting for the repair to be completed. Nevertheless, labor and materials cost is minor compared to the income lost from decreased production.

Jan 1, 1975

By Charles E. Mongan

The problem of roof control in the coal-mining industry is of major importance inasmuch as 65 percent of all coal-mine fatalities result from falls of roof, face, or ribs. The Health and Safety Research and Testing Center of the Federal Bureau of Mines at Pittsburgh, Pa., is engaged in several programs directed toward increasing safety in coal mining. The Roof Control Research Group has 4 programs aimed at reducing roof fall accidents. One of these programs is the use of sonic techniques to explore mine roof strata.

Jan 1, 1961

By M. L. Harris

Explosions in underground mines and surface facilities such as processing plants are caused by confined accumulations of combustible dust and/or flammable gas mixed with air in the presence of an ignition source. Underground explosions can be prevented by minimizing methane concentrations through methane drainage and ventilation, by adding sufficient rock dust to inert the coal dust, and by eliminating ignition sources. The effectiveness of rock dust in arresting explosion propagation was proven by experiment and practice (1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11). The precise mechanism by which rock dust (generally pulverized limestone dust) quenches flame has not been fully explained, but is believed to be absorption of thermal energy from the heated gases and absorption of radiant energy, which reduces the preheating of unburned coal particles ahead of the flame front. One measurable aspect of explosibility is incombustible content. In order to determine whether enough rock dust is applied, 30 CFR1 § 75.403, Maintenance of Incombustible Content of Rock Dust, requires at least 80% incombustible content on the roof, ribs, and floor of underground coal mines. 30 CFR § 75.403-1 further defines the incombustible content as follows: ?Moisture contained in the combined coal dust, rock dust and other dusts shall be considered as a part of the incombustible content of such mixture.? In order to determine the incombustible content of the mine dust, samples of deposited dust from specified areas in a mine must be collected, analyzed, and then compared with the minimum standard of 80%. The traditional low temperature ashing (LTA) approach to determine if a coal and rock dust mixture is compliant with the inerting requirement consumes the coal dust and considers the remaining material to be inert. Compliance with the law is then determined by comparing the measured percentage of inert material of the representative band sample with the pre-established requirement of 80%. The incombustible content of the sample includes rock dust, the amount of moisture as received at the lab, and the inherent ash in the coal. The LTA method is not itself a direct measure of explosibility but is a surrogate that calculates a single parameter associated with large-scale Bruceton Experimental Mine (BEM) explosion test results conducted with dry rock dust. This method assumes a homogenous mixture with no layering of rock dust and coal dust. Float coal dust is a serious explosion hazard if it accumulates on top of the rock dust and is not mixed with the rock dust (12). Mitchell and Nagy (13) studied the effectiveness of water as an inerting agent for the coal dust explosion hazard. The study emphasized that surface water evaporates readily from dusts. Thus, in a passageway where the dust is wet, changes in weather or the ventilation system could dry the dust and make it unsafe in a relatively short period of time. Where adequate rock dust has been applied, this drying effect is not a factor. However, if the mine depends upon the moisture content as part of the incombustible content, fluctuations in the dust surface moisture within a mine can render moisture content an ineffective and inconsistent measure of safety. Additionally, if sufficient moisture is absorbed and subsequently relinquished by rock dust, a cake can form and render the rock dust ineffectual. The trend has long been recognized that mine explosions occur primarily during the winter season when the humidity is low for long periods of time (14, 15, 16). In light of this trend and due to the potential variability of the moisture content of the dust, it may not be prudent to include variable surface moisture in the total incombustible content of the sample. Instead, surface moisture should be viewed as an additional safety measure as long as the rock dust is dispersible. However, moisture limits the ability of the rock dust to disperse and can significantly reduce its capacity to effectively inert propagating explosions (2, 13, 17, 18, 19, 20, 21, 22). Given the methods by which the as-received moisture and incombustible content are determined, dust samples from the 2010 MSHA database were assessed to determine the variability of the moisture content throughout a year and how often the measured as-received moisture might have affected the dust explosibility determination if removed. The findings were then verified by observation in laboratory studies and within the NIOSH OMSHR Safety Research Coal Mine (SRCM).

Feb 23, 2014

By S. S. Mauney

Natural and synthetic colors are used in almost every facet of our daily lives as a means of communication and expression. Natural ochres, umbers, hematites, and magnetites were once used in their crude or semi-processed state for their pigment value in construction products and low-end coatings applications, while yielding, in recent years, to synthetically produced iron oxides for more sophisticated products. Today, through innovative mining, processing, and marketing techniques, natural iron oxide pigments are once again gaining strong inroads into products and markets requiring precise chemical and physical characteristics. With our focus on environmental consciousness and resource conservation, value added natural iron oxides provide an economical and responsible alternative to our color needs.

Jan 1, 1993

By Neall. George M.

No method of roof control yet devised has proven to be universally acceptable for the wide range of strata conditions experienced in U.S. coal mines. However, a relatively new innovation, the roof truss, has proven itself capable of preventing roof failures which both conventional and resin bolting could not. Presently, the economics of roof trusses are not favorable when compared to bolting due primarily to drilling and installation procedures, but this is expected to change with improved truss and equipment designs. To realize the full potential of this new method of roof control, design criteria are needed which can optimize the effect of the truss for varying strata conditions. A review of the literature reveals that some work has been conducted on the roof truss. 1 Gambrell and Haynes (1970) showed that the roof truss is superior to angled roofbolts installed through a header. Sheorey, Verma, and singh2 (1973) used statics to prove that the optimum angle of inclination should be greater than 450? However, to date, no systematic attempt has been made to establish design criteria. In this report, the problem was approached in three ways. First, model studies were performed to determine general trends of truss support as a function of a number of variables. This provided a better understanding of the support mechanism involved. Secondly, beam theory was employed to calculate the actual support capacity of a truss, realizing the many simplifications, assumptions, and shortcomings of this approach to such a complicated problem. Last, field testing will be utilized to test the hypotheses previously developed and provide hard data to further synthesize roof truss design criteria. Field testing has recently commenced and should be complete before mid 1977.

Jan 1, 1977

By J. W. Powell

Several years prior to 1962, it became obvious that in order to develop ore reserves below the Storke Level, it would be necessary to devise a method to facilitate the ore being lifted three hundred feet to the surface or six hundred feet to the mill. The final plans called for an underground crusher complex with two stages of crushing and a conveyor belt gallery for transport of the ore six hundred feet above, to the third crushing stage. Access into the area was gained in 1962, by sinking Five Shaft approximately one quarter mile southwest of the proposed complex site, and drifting into the area. Collar elevation of Five Shaft is three hundred feet above the 600 Level Crusher Complex. All muck was loaded into ten-ton granby cars, hoisted to the surface and dumped. (See Figure 1 for the relationship between Five Shaft and the Crusher Area) Drifting into the Crusher Area contunued until 1965 at which time the Crusher Room Cutout was started. The Crusher Access Drift (CAD on Figure 2) war driven and mining pm- ceeded according to the description on drawings marked Figure 3a and 3b. After the arch portion of the Cutout was excavated and concreted, removal of the center "pillar" commenced. This muck was removed with an Eimco 123C crawler-mounted front-end loader. (See Figure 4) A total of 576,000 cubic feet of rock was removed from the Crusher Cutout. All sup- port was afforded by grouted roofbolts on a specified pattern, as shown in Figure 3c. Crane support columns were put into place and held by braces welded to roofbolt heads. Sidewalls and endwalls were formed and concreted. (See Figure 5 for the finished product)

Jan 1, 1970

By V. T. McLemore

The Steeple Rock district is a major epithermal .gold-silver district in New Mexico that exhibits district zoning. Five types of ore deposits occur in the district. The base-metal veins (with Au and Ag) form the center of the district and occur along the Carlisle fault. The gold-silver veins occur along northwest-trending faults outward from the base-metal veins. The margins of the district are formed by copper-silver, fluorite, and manganese veins. In addition, areas of older acid-sulfate alteration occur throughout the district and also exhibit zoning: massive silica/chert zone (inner), silicified zone, and clay zone (outer). This alteration overlies regional; alkali-chloride (propylitic to argillic to sericitic) alteration. Synthesis of available data suggests the acid-sulfate alteration is related to a shallow but older epithermal hot springs system. Subsequently, younger epithermal veins formed along faults.

Jan 1, 1994

By E. E. Caba

Copper smelter flue dusts containing arsenic are hazardous materials requiring environmentally accept-able disposal, preferably with re-source recovery under the RCRA and CRCLA regulations. However, the known resource recovery processes entail capital and operating costs greater than can be justified by the revenue of the recovered metal. Consequently, the smelting industry is tending to forego resource recovery in favor of encapsulation and storage in a certified class I hazardous waste site, or in a dedicated facility located at the source Superfund site. Order of magnitude costs for this option with portland cement encapsulation are estimated at $100 per ton, not including transportation. Industrial adoption of a new resource recovery process re-quires that its cost, including capital amortization, exceed the cost of encapsulation and storage only by the amount of the offsetting revenue from sale of metal. The lime-roast/ammoniacal leaching process is expected to meet this goal.

Jan 1, 1992

By Chi-shing Wang

In many cases the roof strata of a bedded deposit may be considered as a composite of rock beams of rectangular cross section, whose component layers differ in thickness and may or may not be separable from each other when they are subjected to loading by their own weight. An analytical study of the behavior of such multiple-layer beams is extremely difficult owing to the heterogeneity and anisotropy of rock materials. The complexity is revealed by the fringe photographs obtained from several series of barodynamic photostress experiments conducted on various types of multiple-layer model beams of a medium-grained Bedford limestone. Further discussion on the applicability of barodynamic photostress techniques to the model study of the behavior of mine roofs in stratified geologic media is presented by comparing the phenomenological observations recorded in this investigation.

Jan 1, 1968

By M. Poulton, J. A. Botín, C. Gatica

"The Chilean minerals industry faces a shortage of 27.000 new skilled professional by 2023. Enhancing the integration of women into the workforce is a possible solution. This study analyzes the state of women in the mining workforce over the past decade. Several key indicators are presented: percent in the workforce, salaries, career profiles, presence at management level, and participation in academia are studied. The study also analyzes the strategies used by government, industry, and universities to recruit and retain women for the minerals industry. The main results show that women represent 7.4% of the mining workforce in Chile and less than 1% of senior positions with a salary gap of approximately 30%. Systematically, women prefer professional programs in geology, chemistry, and environmental areas. The Chilean statistics are compared to data from the United States mining industry. INTRODUCTION The Chilean mining industry faces a significant shortage of professionals for the next decade which compromises competitiveness and productivity. The demand for human capital in mining depends on several factors. First, the age structure of workforce, which determines future retirement needs. Second, minerals market considerations, determining the amount and size of mining projects entering production in the coming years. Third, the evolution, positive or negative, of productivity, mainly driven by technology and innovation, and negatively affected by the declining ore grades. Finally, negative trends in lead times to production of mining projects, due to social opposition, changing regulations and other project contingencies, negatively affecting the demand for human capital. Regarding the supply of human capital, the fast increase in the technology level of the minerals industry and hence, the increase of technical qualification requirements of the human capital generates a rise in the time required for trade and university education of mining professionals, which may cause imbalances in the labor market. According to (Consejo Minero, 2014) human capital gap in Chile by 2023 will be around 27.000 workers for extractive, processing and maintenance jobs, which represents 14% of the current workforce (Figure 1)."

Jan 1, 2016

By N. Careddu

In recent years, slabs with a rough surface have captured a large share of the ornamental stone market. However, the main technologies used for this type of treatment are based on mechanical shock (bush-hammering) or thermal treatment (flaming or flame-finishing). These traditional technologies are widely used, but have many limitations that decrease their usefulness. The purpose of this study was to develop a technology that enhances the natural colors of the rock and produces a rough surface without compromising its mechanical characteristics, in contrast to traditional technologies. This report shows the technical, economic and aesthetic results obtained with a new water-jet treatment and compares it with competing technologies.

Jul 1, 2010

By V. L. Brant

The estimated total energy demand for the U. S. is 60 quadrillion BTU for 1970 and is expected to more than double by the year 2000. Today the energy crunch is here. It is evidenced by brownouts to conserve electrical energy, and the shortage of gas and oil. Many such headlines, including suggestions for energy rationing, are in the news today. Paradoxically we have an abun¬dant source of energy in the form of coal. Energy consumers, however, are geared to use fuel in other forms. It is the intent of this presentation to discuss processes under development for conversion of the energy contained in these vast coal reserves to more usable forms. Coal conversion to synthetic fuels should be of particular interest to those engaged in mining. Coal consumption in a single conversion plant is expected to range from 10,000 to 40,000 tons per day. Plants will be located at the mine mouth and will operate continuously 24 hours per day, seven days per week. Further, many such plants will be needed., For example, looking at natural gas only, the supply/demand gap is estimated to reach 13 trillion cubic feet per year by 1985. Assuming that gas from coal conversion were to fill only 101, of this gap, 15 plants producing 250 MMSCFD would be required. These plants would consume about 90 million T/Y of coal or 135 million T/Y of lignite. It will indeed be a challenge to mine, suitably prepare, and transport coal at these projected volumes without interruption. Many ideas have been conceived for better utilization of coal and these are in various stages of development. Those supported by public money are covered by the Annual Report of the Office of Coal Research (OCR), Department of Interior. The two processes to be discussed, the Consolidation Coal Company's (Consol) C02 Acceptor Process (1)(2)(3) and The Pittsburg and Midway Coal Mining Company's (PAMCO) Solvent Refined Coal Process (4)(5) are both sponsored by OCR.

Jan 1, 1970