Search Documents

By A. Iannacchione

Most legacy drift mines entered the coal reserve from outcrop and developed up-dip. The Surface Mining Control and Reclamation Act of 1977 changed this way of mining, requiring all new mines with acid- or iron-producing coal seams to be designed so as to prevent gravity water discharges from the mine. This Act requires engineered barriers to contain the mine pool. In many cases, mine layout designs focus primarily on the size and hydraulic performance of the un-mined coal barrier between the up-dip mine pool and areas where down-dip surface discharge is possible. In other cases, designs focus on preventing discharges from barriers contained within the strata surrounding the mined coalbed. This paper focuses on a detailed analysis of the factors responsible for preventing mine pool discharges to surface waters. Important factors include: mine layouts, mining methods, hydraulic head and conductivity, and geology. While the exact causes for the successes and failures could not always be determined, reasonable mechanisms are presented.

Feb 23, 2014

By E. J. Rorem

Rockfall and unstable rock slopes can be con-trolled by using steel wire-rope net systems as barriers or as slope draping. The chief advantage of such systems over rigid type barriers is the flexibility of wire rope netting. This flexibility and strength permits kinetic energy dissipation with low maintenance requirements. Mining activities can produce temporary or long-term unnatural slopes and unstable rock faces that may produce rockfall hazards. Such conditions can necessitate efforts to minimize the hazard to workers, structures and equipment.

Jan 1, 1996

By Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths (from 500 feet to 1000 feet) and six different diameters (from 14 feet to 24 feet) were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1977

By Zygmunt Sadowski

Problems encountered in barite flotation from various waste materials such as spent drilling muds are likely to be closely connected with the effect of chemical additives and metal ions present either added or present as contaminants, on the flotation. Fuerstenau and Palmer (1976) have studied in detail the adsorption of multivalent cations onto oxide and silicate minerals. It was observed that the adsorption of a multivalent metal species exhibits a sharp pH dependence which is related to the formation of hydroxy complexes of the metal ions in solution. Investigations on the recovery of barite from tailings ponds and mining wastes (Sullivan and Lamot, 1981) have shown that such barite materials can contain large quantities of carbonate and silicate minerals (including clay minerals). Also iron oxide slimes can be present. From these substances cations such as Ca2+, Mg2+, Fe2+ and A13+ can potentially dissolve and be present in the aqueous phase accompanying the various minerals. These ions and their hydrolysis products can have a substantial effect on any subsequent flotation scheme. The present study investigates the effect of the noted ions on both the stability and electrokinetic behavior of barite suspensions.

Jan 1, 1986

By Raymond L. Lowrie

Deregulation, as authorized by the Energy Policy Act of 1992 (PL102-486) allows free-market competition in the electric-utility industry. As the act unfolds, though, uncertainties abound about the type, degree and direction of impacts throughout the affected economy — from fuel suppliers to electricity generators and from power distributors to energy consumers. Instead of having a familiar base of captive customers and electricity prices fixed by negotiation with state public utility commissions, utility companies are preparing for open, free-market competition. They are looking at all areas, including fuel supply, to cut costs to remain competitive. Humorous anecdotes are told about utility companies shunning insiders for senior executive positions. Instead, they are opting for people from the telephone or other industries with deregulation experience. And there are light-hearted stories about a trend away from traditional electric-company names, such as the name of a city or state followed by Edison or Power and Light, to space-age names, such as Ameren, Entergy, Illinova or Unicom. No one wants to be left behind or be perceived to be left behind.

Jan 1, 1996

By P. C. Kapur

The hierarchical relationship between three broad kinds of grinding models for a spatially homogeneous, linear, time-invariant batch grinding system are first established. Limiting and asymptotic arguments for arriving at approximate but simpler models are employed in all three cases. These parsimonious models -provide alternate and, in some respects, more incisive and convenient tools for the analyses of grinding processes and simulation of comminution circuits. In the discrete-size, discrete- time class of models, a reduced mill matrix is derived, which is seemingly adequate for those grinding circuits whose identification otherwise is difficult because of limitations on the quantity of data and its quality. In discrete-size, continuous-time types of models, parameter lumping has been employed for obtaining a G-H solution which is quite accurate and exceptionally useful for graphical display of data, model verification, and parameter estimation and simulation. In continuous-size, continuous-time models, a similarity transformation is used for solving the integrodifferential equation of grinding. This solution provides a unified framework for a number of apparently diverse empirical grinding phenomena such as self-preserving behavior of ground particle size distributions and energy laws.

Jan 1, 1987

By K. A. Natarajan, Abha Kumari

In this paper, electroleaching and electrobioleaching of ocean manganese nodules are discussed along with the role of galvanic interactions in bioleaching. Polarization studies using a manganese nodule slurry electrode system indicated that the maximum dissolution of iron and manganese due to electrochemical reduction occurred at negative DC potentials of -600 and -1,400 mV(SCE). Electroleaching and electrobioleaching of ocean manganese nodules in the presence of Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans at the above negative applied DC potentials resulted insignificant dissolution of copper, nickel and cobalt in IMH2S04 and in sulfuric acid solution at pH 0.5 and 2.0. Mechanisms involved in electrobioleaching of ocean manganese nodules are discussed. Galvanic leaching of ocean manganese nodules in the presence of externally added pyrite and pyrolusite for enhancement of dissolution was also studied. Various electrochemical and biochemical parameters were optimized, and the electroleaching and galvanic processes thus developed are shown to yield almost complete dissolution of all metal values. This electrobioleaching process developed in the laboratory may be cost effective, energy efficient and environmentally friendly. Keywords: Ocean manganese nodules, Electroleaching, Electrobioleaching, Galvanic interactions

Jan 1, 2003

By Chulho C. Song, Liam Coleman

Alkaline pressure oxidation (POX) is an oxidative pre-treatment option that is commercially used for high-carbonate sulfidic gold ores. The high carbonate grades within the feed ore shifts the ideal operating pH to a basic regime. Compared with acidic POX, alkaline POX typically requires additional steam input due to a lower sulfur oxidation load and a high rate of in-situ carbon dioxide generation that needs to be vented along with steam. The cost of this steam addition is the largest differentiator between acid POX operation and alkaline POX from a cost comparison. However, alkaline POX can offset these costs through reduced acid usage for pre-acidulation and decreased alkali reagent consumption for subsequent neutralization. This paper reviews the specific operating cost impacts of acid/base consumption between alkaline and acidic POX with ores which require pre-acidulation, the overall economics of alkaline POX, and the regimes in which alkaline POX is economically favorable. The findings aim to guide industry professionals in making informed decisions for alkaline POX adoption by providing a summary view of its operational benefits and costs, contributing to the development of cost-effective and sustainable gold ore processing techniques.

Feb 1, 2025

By Sotiris Psomas, Colin M. Eddie

"Steel Fibre Reinforced Concrete (SFRC) Segmental Tunnel Linings have successfully been used for over 20 years in the UK and have been adopted in a number of high profile projects such as High Speed 1, Crossrail, Thames Tideway, as well as High Speed 2. Tunnel linings and especially SFRC design are not covered in the Eurocodes. This shortage of SFRC tunnel design rules seems to be partially addressed by several international publications. However, in the UK, the ‘design-assisted by testing’ (DAT) approach has also been adopted. The Paper discusses the UK’s best design practice and focuses on the DAT methodology as applied in the case of the 6.9km (4.3miles), 7.8m (25.6 feet) ID Lining for the £635million Lee Tunnel Project. The design approach, the full scale testing at the Building Research Establishment (BRE), and the construction innovations are presented. This experience will be transferred to the £4billion Thames Tideway Tunnel.INTRODUCTIONSteel Fibre Reinforced Concrete (SFRC) has been used for Tunnel segments for more than 20 years. The first application of SFRC in the UK was for the Heathrow Baggage tunnel (1994). Since then significant size tunnels have been designed and constructed, such as the Jubilee Line (1999) High Speed 1 (CTRL, 2006), Crossrail (2014), Lee Tunnel (2014) and the scheduled 25km Thames Tideway (‘Super Sewer’) and High Speed 2 rail tunnels. However one the main obstacles in achieving streamlined design and improving efficiency are the lack of appropriate design guidelines for SFRC tunnel segments. This issue will – to some extent – be addressed by a number of current documents on tunnel FRC design either being produced by BSi (PAS8810, expected 2016), ACI (544.R) and ITAtech (Design Guideline PCFRC, 2015) in an effort to advance the design of SFRC and take into consideration the recent developments in Steel and Macro-Synthetic FRC technology."

Jan 1, 2016

By B. A. Firth

Australia is the largest exporter of coking and thermal coal to the international market. This market has required that the coal being presented to the customer has a particular level and consistency of quality. In this context, the Australian industry has developed coal preparation practices that allow this criteria to be met while maximising the recovery of coal from the resource. This has required on- going developments in both coarse and fine coal cleaning technology over the past 30 years. Coal flotation has undergone a number of developments with regard to maximising recovery from the overall plant circuit. This includes innovative flotation circuits (split feed), methods of enhancing the use of reagents and control of pH. During the 1990s, there have been major changes in flotation as practised in Australian coal preparation plants. Columns have become the preferred technology for both greenfield developments and plant upgrades. This paper will outline the above developments with a number of plant examples and the reasoning that has driven the change. The ongoing research that is being carried out on new cells to optimise the overall fine coal circuit will also be discussed.

Jan 1, 1999

By Gary L. Mowrey

Visible and sometimes audible indications of excessive underground rock pressure such as pillar fracturing, squeezes on chocks, and "roof talk" are familiar to mining engineers. Such signs often precede rock failure on a larger scale and therefore may be used as a warning. Nevertheless, these subjective observations do not provide an adequate means of evaluating the existing rock pressure conditions in a mine. One method which appears to be extremely promising in determining the stability of geologic structures in general is that of monitoring their associated micro seismic activity. Mining engineers generally agree that during the process of rock deformation and failure small-scale seismic ("microseismic") vibrations are produced in the rock itself. These transient vibrations propagate through the rock structure and may be detected at a considerable distance from the failed rock by employing suitable electronic monitoring equipment. Hardy (1) has presented a detailed review of microseismic research in the mining, petroleum, and geoscience areas, and it is apparent that relatively little application of micro seismic techniques have been made in coal mines. This is especially true in North America since here most coal mines are fairly shallow and consequently are not generally subjected to excessive stresses. Furthermore, strict Federal and State mining laws limit the use of electrical equipment in coal mines complicating the use of the necessary monitoring facilities. In terms of both mine safety and economics, monitoring microseismic activity appears to be invaluable in the detection and location of over-stressed pillars and unstable roof conditions caused by development and production work. In 1970 The Pennsylvania State University Rock Mechanics Laboratory became involved in a research project, sponsored by the U.S. Bureau of Mines, to investigate the feasibility of using microseismic techniques to detect and to locate potential regions of instability around a longwall coal-mine operation [Hardy and t10wrey (2); Mowrey (3)]. In this study geophones (velocity gages) located in an array of shallow boreholes drilled from the surface above the active area of the longwall were employed to detect microseismic activity, and a mobile micro-seismic monitoring facility was used to condition and record this data for later analysis. This project is unique in that measurements were made from near-surface geophones rather than geophones installed on the mine itself. Two advantages are apparent, namely that (1) there are no electrical limitations on the monitoring system and that (2) mining operations can continue normally because there is no monitoring equipment or cables in the mine.

Jan 1, 1978

By Henryk Bystron

The underground fire areas are formed as a result of failure of an active fire extinguishing in mines. Such areas bring about a fire hazard for the work safety and for the mining operations. For liquidation of fire areas it is necessary to create conditions under which a possibly small amount of air is flowing to the fire. To achieve this end, isolation methods are used which consist in erection of full stoppings of various types, sealing practically the fire areas. These methods usually fail in oases when the coal seam is thick and the fire area is situated between the intake shaft and the outtake shaft in which a high-pressure fan is in operation. In such oases ventilation methods based on the balance of aerodynamic potentials in fire areas are to be used. For a very long time the isolation and ventilation methods have been developed in the world mining, No sooner than since 1980 the aerodynamic potential has been used in ventilation methods [1,2,6]. So far, the aerodynamic potential was called in different ways and was determined by different formulae which gave its numerical values more or less approximative. Nevertheless, even in situations featuring by a lack of sufficient theoretical bases of the aerodynamic potential the ventilation methods brought considerable profits in the field of safety in mines and of economics in mine ventilation [1-6,9,10]. The increase in the depth of underground mines and their equipment with expensive machines (apparatus) brought about that the Central Mining Institute at Katowice undertook research works which are crowned by the theory of the aerodynamic potential in mine ventilation networks [7]. The use of this theory in the mentioned ventilation methods will increase their effectiveness. Since the theory will be published in the III rd quarter of this year, we cite in the present paper the formulae and relations associated with this theory which are indispensable to present the balance of aerodynamic potentials in the fire areas in their control by ventilation methods.

Jan 1, 1980

By Gordon O. Prickett

In two case studies we look at strategies of acceptance that the analyst can employ to gain entrance and to see his problem solution out to use. The first example comes from metal mines. The problem area was excessive usage and cost of wear parts in the concentrator and an atmosphere of crisis over frequent and unexpected breakdowns. The second case pertains to coal exploration. Better methods were being sought for representing coal quality in developing reserve tonnages. The first strategy is - Develop a detailed Human Impact Statement. The second strategy is - Write down in plain language with the keeper of the problem what he will consider as success in dealing with his problem.

Jan 1, 1978

By Ted D. Johnson

INTRODUCTION The tailing dam is part of the SOHIO L-Bar Uranium Mine and Mill located about 70.8 kilometers (44 miles) west of Albuquerque in northwestern New Mexico. The dam location is shown on Figure 1. The tailing dam is one of the last upstream method dams permitted in the industry. Design and construction aspects of the project, as well as operation and maintenance considerations, are reviewed herein. Since initial construction, SOHIO Western Mining Company and Woodward-Clyde Consultants have developed several modifications and improvements in the dam's operating and monitoring procedures. This work has been done in coordination with the New Mexico State Engineer's Office and in accordance with recommendations in a report done for the Corps of Engineer's Phase I Dam Inspection Report. Modifications and improvements described should be of particular interest to owners and operators of other tailing dams utilizing the upstream method of deposition. The tailing facility was designed for a 10-year life to provide an ultimate storage capacity of 6 1/2 billion kilograms (7 1/2 million short tons) in an area of about 180 acres. A plan view of the tailing dam is shown on Figure 2. The tailing consists of approximately 75% sand size material and 25% fines (material passing the No. 200 sieve). The tailing dam includes a small earth starter dam with raises of the dam accomplished using tailing deposited by upstream method techniques. The starter dam is a homogeneous embankment about 610 meters (2000 feet) long, a maximum height of 12 meters (40 feet) and 2 1/2:1 (horizontal to vertical) upstream and downstream slopes. The starter dam contains an internal drainage system which includes a near vertical chimney drain connected to horizontal finger drains. A typical section through the maximum height of the starter dam is shown on Figure 3. A small confining dam, approximately 1.6 meters (5 feet) high, is constructed beyond the limits

Jan 1, 1980

By W. E. Anderson

As part of a larger study to identify factors influencing the practical operating life of wire rope used on large draglines in surface coal mining, field trips to operating surface coal mines were made during late 1975. Wire rope performance information was obtained from personnel at thirteen mine sites west of the Appalachians. Seventeen pieces of equipment, utilizing buckets ranging from 30-to 220-cubic-yard capacity, were documented. We have judged that U.S. surface coal mining draglines, 30 yards and larger, can be represented as 120 machines having 60-cubic-yard buckets, moving 1.8 x 10 yards of overburden during 6,650 hours of productive availability per year. Based on our limited field study, we have calculated that downtime resulting from rope-related causes averages 105.6 hours per year for each (typical 60-yard) dragline. The total lost production from this source alone is thereby estimated at about 25 x 10 yards annually. Although study findings did not reveal anything about dragline rope life that wasn't known or practiced by one operator or another, most operators could expect improved rope life by periodic review of their practices and by adopting or adapting one or more life-improvement measures employed at other sites. Since rope productivity was found to vary by about five to one, among the sites studied, we believe considerably improved average performance is possible. As little as ten percent overall improvement would mean increased national productivity exceeding two million yards of solid overburden removal, and associated savings in rope costs alone of some two million dollars annually, not to mention any reduction of labor-related expenses. This report outlines preliminary findings which may prove useful to many operators in extending wire rope life, thereby lowering expenses and increasing surface coal mining productivity. Some of these modifications or adjustments in maintenance/operating practices would not require capital investment. We did not find anyone who had tried cost reductions by using presocketed dump

Jan 1, 1977

By P. R. G. Brandão

In this investigation, the differences in the absorption spectra of etheramines, fatty amines and condensates, mostly present as acetates, from several suppliers are characterized by means of infrared spectrometry. Sharp differences were observed in the absorption spectra of three types of amines and derivatives. Etheramines show a characteristic and well-defined peak at 1,114 cm-1. This peak is due to the ether C-O group and differentiates etheramines from the other classes. The absence of such a peak indicates that the species is not an etheramine. The distinction between condensates and fatty amines is made by the presence of a sharp peak around 3,200 cm-1. This peak is probably due to the proximity of the N-H amine groups and C=O carbonyl groups in the amide portion of the condensate's molecule and by different and better-defined bands in the 1,800- to 1,500-cm-1 range. The flotation performance of these amines was evaluated by means of the laboratory-scale flotation of an itabirite ore. The etheramines proved to be the most effective collectors for this system. Monoamines presented better performance than diamines for the ore under investigation.

Jan 1, 2002

By William D. Hanson

Celestine (celestite) (SrSO4), the primary ore mineral of strontium, is present in the DeQueen Limestone Member of the Trinity Group (Lower Cretaceous) in Sevier, Howard, and Pike Counties, southwest Arkansas. Two mappable celestine beds have been identified. One bed is commonly 3-5 in. thick, but ranges up to 18 in. in thickness; the other bed is generally 2-3 in. thick. The beds are concordant within the DeQueen Limestone and were formed by precipitation from periodically restricted sea water. Reports concerning celestine date back to 1929, when Hugh D. Miser and A. H. Purdue mapped the geology of the DeQueen and Caddo Gap quadrangles. A small amount of celestine was produced in the early 1940s in Howard County. During 1941, the J. W. Hintze Company collected 1,500 pounds of celestine for testing purposes. In 1942 and 1943,750 test holes were drilled by the Bennett-Clark Company in Howard County. Afterward, approximately 90 tons of celestine was open-pit mined and shipped to Texas for processing. Since then, no mining of celestine in Arkansas has taken place.

Jan 1, 1999

By A. Foscolos

Land reclamation and rehabilitation of depleted coal mines in the wider area of Ptolemais-Amynteon is practiced by the Division of Mines of the Public Power Corporation of Greece in order to conform to the concept of environmentally sustainable economic development of its operations. Detailed chemical and mineralogical studies were performed on reclaimed soils and their crops in order to evaluate the results of land reclamation and rehabilitation while similar studies were undertaken in adjacent, regularly cultivated, soils. Results indicate that trace element concentrations as well as concentrations of elements of environmental concern to be higher in regularly cultivated soils than the reclaimed ones. However, the concentration of the elements in wheat grains harvested from both, regular and reclaimed, group of soils is the same. The reason for this behavior is the very low water solubility, of the elements in the soils, due to their high pH values and the nature of their occurrence. As a result, wheat crops produced from reclaimed-rehabilitated soils developed on depleted lignite mines in the wider area of Ptolemais-Amynteon do not pose any health problem on either humans or animals when consumed.

Jan 1, 2003

By J. E. Gebhardt, P. E. Richardson

External control of the electrochemical potential of a bed of mineral particles was investigated by the US Bureau of Mines as a method for controlling particle interaction with organic collectors and, thus, flotation response. A cylindrically shaped, 200- to 300-g bed of sulfide mineral particles was used as the working electrode in an electrochemical-flotation cell. In a pH 9.2 sodium tetraborate buffer, chalcocite floated with ethylxanthate at applied potentials [=] - 0.25 V (versus the standard hydrogen electrode) ; pyrite floated at potentials [=] 0.15 V. Differential separation of a chalcocite-pyrite mineral mixture was obtained by controlling the potential, but the flotation response of the mixture did not follow the behavior predicted from measurements on the individual mineral beds. Chalcocite dissolution products had a deleterious effect on chalcocite-pyrite separation by activating pyrite so that it floated below the potential (~ 0.13 V) at which xanthate is oxidized to dixanthogen. A pyrite bed activated with a copper(II) sulfate solution exhibited a flotation response with a potential dependence between that of chalcocite and pyrite. Pyrite dissolution products had no effect on chalcocite flotation.

Jan 1, 1988

By William J. Maloney

OVERVIEW Blind drilled shafts are becoming increasingly popular, particularly in the Appalachian coalfields, as a secondary and sometimes primary means of ventilation. The reasons for the rebirth of the blind shaft are mainly due to it's economics, timeliness, safety characteristics and inherent independence from underground operations. Historically blind drilling has been used to a limited degree in hard rock and tunneling ventilation. With the recent advances in cutters, bit design, equipment and lining systems, particularly in the Appalachian coalfields, blind drilled shafts are once again the shaft construction technique of choice to the educated ventilation specialist. [ ] HISTORY OF BLIND DRILLING Blind drilling has it's roots in numerous places, including the Nevada Test site, the coalfields of Appalachia and Germany along with the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin with oilfield drillers entering the industry on a project basis only to "pull in their horns" and return to the oil patch. Shafts completed by oilfield equipment range from the shallow 5' and 6' lined shafts on the Nevada test site to two (2) 10' lined, 730' deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths with the record being a 90" diameter, 6,150' deep shaft being completed in the Aleutian Islands of Alaska in 1969. EQUIPMENT Oilfield equipment is still being used on the Nevada test site but elsewhere specialized blind hole equipment has been developed to enhance the efficiency of particular applications. Where steel liners are required the A-leg derrick with a simple hoist and rotary system is used. The largest user of this type equipment in the world is the former USSR where blind drilling for mine ventilation is the norm. On applications where trip time and cutter changeout are a priority, top drive hydraulic rigs have been developed which are highly automated, efficient and mobile. These rigs are particularly well suited for tunneling applications where shafts are shallow and sites are usually tight.

Jan 1, 1993