Search Documents

By Robert W. Roscoe

For over a century, St. Joe Minerals Corporation in Southeast Missouri has been sinking shafts for their lead mining operations. Upon discovery of the Viburnum Trend, or "New Lead Belt", St. Joe brought its experience and expertise in shaft sinking to the area. Eleven shafts were then sunk in an 18 year period, ending in 1972. In 1981, St. Joe began sinking a new shaft in the Trend with hand-picked employees from the four operating lead mines and service facilities. The paper describes the general history of St. Joe shaft sinking methods and equipment, focusing on the current development of the Viburnum No. 35 Shaft.

Jan 1, 1983

By Lance Rasband, Richard Hanke, John Starcevich

"Mining on Seattle’s SR99 tunnel began in July of 2013. Initial mining progressed slowly through a 4.5 m (14.9-ft) thick fiber-reinforced concrete headwall before immediately entering the first of three planned safe havens. Once through the headwall and safe haven the machine would move through roughly 122 lineal m (400 ft) of jet grout improved soil at a rate of slightly more than 1.6 m/d (5.3 ftpd). It was anticipated that once mining has passed through the improved area, “Bertha” – now the world’s second largest tunnel boring machine (TBM), would be moving at a rate of almost 11 m/d (36 ftpd). By the end of October 2013, Bertha had mined roughly 131 m (430 ft), averaging 1.4 m/d (4.7 ftpd), and had begun mining within native soils. By the start of December 2013, tunneling had reached the 244 m (800 ft) mark and Bertha was averaging 3.6 m/d (11.9 ftpd), achieving as much as 12.8 m (42 ft) of progress on given days. Unfortunately, on Dec. 6th, 2013, Bertha began to stumble and all progress quickly came to a halt.Initial reports stated an obstruction had stopped Bertha in her tracks. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic pressure within the ground around the TBM, to allow the contractor’s personnel to inspect the cutter head from within and also to investigate for the presence of obstructions at the face of the cutter head. During inspection, the contractor’s crews found fragments of steel pipe entangled in the cutter head. The steel was apparently from an abandoned 254 mm (0.9 in.) diameter monitoring well casing, previously installed by the Washington State Department of Transportation (WSDOT) to monitor groundwater conditions for the design and planning of this tunnel project. After the steel was removed from the cutter head and cleared from Bertha’s path, she attempted to move forward but was only able to generate a slow crawl."

Jun 1, 2016

By T. W. Camm

"We hear all the time about the value of hard work and perseverance, and the part they play in the professional life of successful people. What we do not hear so much about are the many professionals who work hard and persevere, yet never seem to quite reach the level of success they aim for. Some current authors are beginning to give more attention to the part luck/black swans/outliers play in success. This is not a new phenomenon, Machiavelli had a lot to say about it back in the Renaissance. So how can knowledge of this dynamic help in a modern organization? INTRODUCTION Work hard and you will succeed. Go to the right school, major in the right degree, study hard, and get a good job. Look at the lives of successful people, and do what they do. Be all that you can be. You can be anything you want to be. Really? Those who are successful always get attention, people want to know what they did to reach such a high position. Invariably, at least part of their narrative will include hard work, wise insight, taking advantage of opportunities, etc. If they are of a more generous nature, they might also allow that building the right friendships and collaborations also played a role. All of this may be true; what we do not often hear are the stories of those who did all of these very same things, but did not find success. An example from pop culture: The Voice. I have watched this show occasionally the past couple of years. One of the things I like about the show is that the initial screening of contestants is based solely on their singing voice (hence the name of the show), and not on their appearance. At the time of this writing (early November), the judges have just finished elimination rounds for their final teams to go on to the live shows. Here is my point—in almost every case the judges agonized over choosing who would go forward and who would be eliminated. And the reason is because all of them are really talented singers. It is impressive how gifted they are. At the end of each season, only one is declared a winner, out of that gifted pool of singers. When you hear their stories, they are all talented, hard-working individuals sacrificing for their art. And as far as I know, none of them has ever become a star. Hard work, dedication, sacrifice, talent—sometimes it is enough, sometimes not. I will be looking at the part uncertainty/luck/black swans play in our lives, but I want to make it clear at the beginning that I am not saying everything that happens to us is out of our hands or beyond our control. Taleb makes this same point (2007, p. 52): “This problem is chronic: if you tell people that the key to success is not always skills, they think that you are telling them that it is never skills, always luck.”"

Jan 1, 2017

By P. Kawahata

Newmont?s Twin Creeks Mine, located in northern Nevada, is producing gold ore from surface mining operations. The ore is currently processed at three different on-site facilities depending on ore type and grade. Processing facilities operate under stringent geochemical blending constraints that must be met from mine ore deliveries and off-site sourced ore. To analyze various strategic options, the technical team utilizes the mathematical optimization approach. However, due to the size and complexity of the operation, there are unique challenges in optimizing life-of-mine production scheduling. This paper describes those challenges and methods developed to take advantage of different scheduling software to effectively compensate each other and result in reasonable guidance. This paper also describes how those scheduling results are reflected in detailed mine plan and cost estimate work.

Jun 1, 2013

By Nikhil Dhawan, SHAILA MIR

Consumer preference for ever-higher laptop performance coupled with laptops’ declining lifespans make them a significant contributor to electronic waste. An in-depth evaluation of elemental composition and distribution is important for determining metal recovery potential and sustainable recovery processes. In this work, the characterization of individual components of laptops is studied for the systematic identification of important elements and for streamlined and structured recycling, to reduce processing steps and improve economics. A process flowsheet highlighting various recycling routes by targeting metals and various components is also proposed.

By Lynn Salvati, Colin LaVassar, Loic Galisson, Joel Theodore, Lynette Sla

"Sound Transit’s University Link and Northgate Link projects will add 6.75 miles (10.9 km) of twin-bored tunnel to Seattle’s light rail system, extending the route north from downtown Seattle. The tunnels are being constructed primarily in glacial soils using pressurized-face tunnel boring machines. Cover over the tunnel alignment varied from 13 feet to over 300 feet (4–91 m). Since the tunnels are located in densely populated urban areas, controlling ground movements and monitoring settlement were essential to success of these projects. Hundreds of geotechnical instruments, including extensometers, surface settlement points, and near-surface settlement points, were used in both projects to monitor settlement. The observed data were compared to settlement predictions made prior to tunneling, and analyses performed to update empirical factors to better estimate settlements. Recommendations for designing efficient and cost-effective settlement monitoring programs are provided based on the review of the monitoring data and analyses.INTRODUCTIONThe paper includes data from Sound Transit’s University Link and Northgate Link projects. These projects will add 6.75 miles of twin-bored tunnel to Seattle’s light rail system. The tunneling for University Link will extend the light rail system from downtown Seattle to the University of Washington. Tunneling from downtown Seattle to the Capitol Hill Station was completed under the U230 contract, and tunneling from the Capitol Hill Station to the University of Washington Station was completed under the U220 contract. The Northgate Link extension will extend the light rail line north of the University of Washington, including approximately 3.5 miles (5.6 km) of twin tunnels between the University of Washington Station and the Maple Leaf Portal and two stations, U District Station and Roosevelt Station. Tunneling for the Northgate Link project is still underway as part of the N125 project. At the time of writing, tunneling from the Maple Leaf Portal to Roosevelt Station has been completed. Therefore data labeled as N125 in this paper only include the portion of the alignment from the Maple Leaf Portal to Roosevelt Station."

Jan 1, 2016

By John P. Anderle

A tectonically disturbed sequence of Mississippian age evaporites expressing a 5 milligal negative gravity anomaly near Sussex in southeastern New Brunswick, Canada, was investigated by a program of drilling, geologic and geophysical work over the past 27 months. Seventeen of twenty-one drill holes have penetrated 10 to 140 feet of potash mineralization in a salt sequence underlying 2 000 to 3 000 feet of arenaceous, conformable red beds, also of Mississippian age. Bromine and borate studies, lithological characteristics and geophysics, have facilitated improved understanding of the salt structure. The salt sequence has been affected by f1owage which has resulted in both major and minor folding. In the more disturbed areas, the potash interval was extensively subterraneally eroded at the upper anhydrite-salt contact.

Jan 1, 1978

By Steven M. Puricelli

In recent times, smelter off gases treatment plants have become more efficient and environmentally friendly. Where in the past it was acceptable to process only high strength, treatable furnace gases, new smelters must now treat primary gases and abate dust and SO2 from secondary gases: Processing smelter gases can present some interesting challenges. Some equipment can see varying concentrations of sulfuric acid, up to the boiling point, with a periodic table of contaminates thrown in for good measure. Treating weaker secondary gases have, in the past, been cost prohibitive. Nowadays, new technology, like physical absorption or catalytic carbon, show promise for economically treating low strength secondary gases. Modem smelters do a much better job of treating the SO2 laden gases generated by the smelting process but significant challenges remain.

Jan 1, 1998

By R. L. Loofbourow

SEVERAL categories of storage are used depending on capacity. Operational storage, which is small in comparison with the market, facilitates handling surges of a few hours' or a few days' duration. Seasonal storage, usually larger, permits accumulation of product during sea- sons when demand is low, for delivery when demand is high. In producing areas, large storage may permit production at a uniform rate, without waste or distress sale. Near large markets such storage increases the efficiency of transportation, allows a more extensive or higher grade market to be served, and affords protection against interruption in delivery.

Jan 1, 1959

By A. E. Halim, J. F. Brune

Debate continues over whether barricading in refuge chambers is a good strategy to survive entrapment emergencies in underground coal mines, in particular fires and explosions. Unlike U.S. coal mines, Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes the merits and problems of using refuge chambers or self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. We found that using refuge chambers may not be the best strategy during extensive fires or when multiple explosions occur. In these situations, mine rescuers are unlikely to be able to extract miners who are sheltered in chambers and, conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as the level 1 emergency exercises required in Queensland, Australia. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By Donald Towse

Portland cement is a basic building material in every country in the world, and, fortunately, the raw materials required in its manufacture are widely distributed. It is a low-priced bulk commodity (price one cent a pound or less, with a density of 100 pounds per cubic foot.) Table 1. Approximate price per pound of selected mineral products. Copper 48 cents per pound Aluminum 27 Lead and zinc 15 Asbestos 3 to 18 Pumice 6 Sulfur 2 Bauxite (abrasive) 1.8 Barite 1 to 1.6 Cement 1 Primitive regions may get along without any Portland cement, but most countries use some, and it is one of the most widespread building materials, even if used in small quantities. Use of cement begins early in a country's development, and, because of local availability of raw materials, cement manufacture is one of the first heavy industries many countries desire. Use and manufacture of cement usually precedes other industrial materials such as steel and heavy chemicals, and consumption levels off for a long period during development of infrastructure and an economic base. With a mature economy comes a very high consumption. Per capita consumption varies ten times or more between nations (Figure 1).

Jan 1, 1970

By Jr. McCulloch

Mining operations of Freeport Indonesia (FI) are located approximately 4 degrees -6' south latitude, 137 -7' east longitude in Irian Jaya the eastern most state of Indonesia (Figure I). The mines are located approximately 96 km (60 miles) from coast in the Carstenz Mountain range. The ore bodies are between 2900 and 4000 meters (9500 and 13 000 ft) elevation.

Jan 1, 1989

By A. W. Storm

Vertical shaft furnace design and operation have their roots deep in antiquity. There is substantial evidence to indicate that iron was reduced from its oxides to serve mankind's needs long before recorded civilization - - actually prior to 3500 B .C. For at least 5500 years man has been matching wits with Nature to find better methods of extracting this most common, yet essential, metal from her, grasp. And, during nearly all of this period, the vertical shaft furnace has played a principle role in this dramatic struggle.

Jan 1, 1962

By F. C. Schwerer, C. R. McKee, J. C. Seccombe

Production of methane from coal seams requires hydrofracturing, and the length of a hydraulic fracture determines we11 spacing. Since the volume of fluid injected is known, the fracture length is the volume divided by average width and height. If the fracture is contained in the known height of the seam, then fracture width becomes the major factor con- trolling length. Width is proportional to coal compressibility; bulk compressibility is known to be larger than intrinsic compressibility. A method is given here to measure in-situ compressibility (a) from transient pressure testing. Theory linking flow in porous media with rock mechanical properties is reviewed. A consistent derivation of the porous flow equation is given incorporating 3-D deformation and the effective stress parameter "st' linking changes in effective stress and pore pressure. The relations for "st' in terms of a and intrinsic compressibility (ai) are substituted into the field measured porosity-compressibility product (net) and solved for a, the constrained matrix compressibility. In a field example, using 4 wells with an anisotropic analysis, the ratio of major to minor permeability was 17 for the Pratt A seam. a was found to be 6x10-5/psi as opposed to the laboratory value of 1.4x10-6/psi.

Jan 1, 1986

By Lei Pan, Venkata Atluri, Xuming Wang, Yuesheng Gao, Jan D. Miller

Polysaccharides have been used as depressants for naturally hydrophobic talc in the flotation of base metal sulfide ores, precious metal sulfide ores and platinum group metal (PGM) sulfide ores. The results of this surface chemistry study confirm guar gum as a preferred polysaccharide for talc depression in the flotation of these ores. In addition to the practical application of the research results, the surface chemistry results are of academic significance, providing further information to understand how polysaccharide depressants function in these complex sulfide flotation systems.

By S. Acar

The results obtained for the selective flocculation or flotation of natural ores do not usually agree with the corresponding properties of the constituent minerals when present alone. This is mainly due to the presence of dissolved mineral species which can interact in many ways with other components in the system and alter their behavior. In this paper, the effect of dissolved species on the flocculation and electrokinetic properties of sulfide minerals is disscussed. Dissolved Fe, Cu and Ni species are found to affect the properties of chalcopyrite, pentlandite, millerite, pyrrhotite and covellite in certain pH range. These effects are interpreted in terms of species adsorption leading to activation or depression of reagents, surface precipitation and complexation of species, etc.

Jan 1, 1985

By M. C. Rockwell

There are approximately 1,800,000 t of discarded dolomitic-limestone tailings from the Gays River lead/zinc mining operation in Nova Scotia. Neutralization effectiveness similar to an agricultural grade limestone and low contents of residual metals make the tailings a suitable source' of soil conditioner material for the local market. However, the fine particle size, 98% passing 147µm, and a high moisture content make their handling and application difficult. Agglomeration of the tailings into relatively small hard pellets was investigated and difficul¬ties were overcome. Pellets with a range of pH values and various amounts of soil nutrients and moisture content less than 10% were obtained, from tailings containing 20% initial moisture, through the addition of less than 15% selected materials.

Jan 1, 1985

By Tsutomu Yanagase

Non-ferrous smelting industry in Japan often had the severe problems about the over production of sulfuric acid. There has been such a closed relation between amount of sulfuric acid from non-ferrous smelting industry and the products of copper, zinc and lead metals that the production of one ton of copper accompanies three tons of H2S04. When the proper balance exists in both markets this situation certainly brings bigger profits. In Xining and Metallurgical Institute of Japan the research commitee concerned with the fixation process of sulfur in non-ferrous smelting industry was established in 1977 and continued the activity for four years untill 1981. This paper will introduce some of the activities involved in the report published by the committee.

Jan 1, 1982

By V. A. Evans

The preparation of a paper reporting fluorspar economics in the United States at one point in time could have been somewhat complicated be- cause of the number of producers, both large and small, that derived production from different locations throughout the Western U. S. and the Southern Illinois and Western Kentucky fluorspar districts . Companies such as Allied Chemical and William- son Mining operated in the Jamestown district of Colorado. In Walden and Salida, Colorado, the Colorado Fluorspar Company operated mines and mills.

Jan 1, 1986

By K. N. Han, Y. Guan

[The dissolution behavior of copper and gold from their pure state and from Au-Cu alloys in cyanide solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of the alloy composition, stirring speed of the disc. [lixiviant] concentration, solution pH and temperature on the overall dissolution kinetics has been studied. An-Cu alloys of three compositions were used in this study. The atomic percent of gold in these alloys was 75, 50 and25, respectively. The dissolution behavior of these three alloys was compared, under the same chemical conditions, with that of pure gold and pure copper. In general, the dissolution of copper and old from alloys is controlled partially by surface chemical reaction and largely mass transfer.]

Jan 1, 1994