Search Documents

By Ross W. Smith, Xiapeng Zheng, Merrill P. Allen

The results of flotation of a primary desliming hydrosizer overflow material containing 14.6 wt.% P20, and 3.6 wt.% MgO are presented. The phosphate minerals were collophane and francolite and all minerals appeared to be liberated. The material had not been previously treated with flotation reagents. In the experimentation, various collectors were evaluated for effectiveness. The relative effectiveness of flotation in different flotation devices was determined. Finally a two-stage flotation scheme is proposed using column flotation of dolomite in the first stage and Denver cell flotation in the second.

Jan 1, 2002

By S. G. Malghan, V. K. Pujari

Detailed characterization of all the powder constituents during powder processing is necessary for the reproducible manufacture of ceramic components that will perform reliably in intended applications. In this paper, selected physical and surface chemical techniques for characterization of silicon nitride powder are evaluated. The characterization data are discussed in the context of how these data, through their influence on powder processing unit operations, can affect the final microstructure. In the forming of ceramics, some of the major variables of injection molding are evaluated. Accurate measurement and control of these variables is emphasized for manufacture of Si3N4 ceramics with a high degree of reliability.

Jan 1, 1990

By W. F. Hahnert, P. A. S. Ralston

In off-line training of a rule-based controller, the significant measure of successful training is the quality of control provided by the generated rule set. In an adaptive or on-line control environment, performance is also measured by the ability to accurately maintain a satisfactory rule set, but within constraints on speed and/or resource availability. Very small population genetic algorithms, or microGAs, have been proposed as a means of capitalizing on the hill climbing characteristics of faster local optimization techniques while requiring less memory and retaining much of the robustness of traditional, larger population genetic search. A traditional genetic algorithm and a similar microGA are developed and applied to two control problems. The performance of these algorithms is analyzed with respect to (1) the quality of the rules learned, (2) the rate at which learning occurs, and (3) the memory resources required during learning.

Jan 1, 1993

By S. W. Beckman, L. Williams, A. E. Seep, R. Fischer, J. Hubbard

Introduction The Summitville Mine located in southwestern Colorado was added to the National Priorities List in June of 1994. Summitville was the site of mining operations that began in 1873 with the discovery and development of gold placer and lode deposits in the late 1800's. The mine site is located about 25 miles south of Del Norte, Colorado in the San Juan Mountains adjacent to the Rio Grande National Forest at an approximate altitude of 11,600 feet. The site was mined for gold, silver and copper between 1873 and 1947. The Summitville Consolidated Mining Corporation, Inc. (SCMCI), a wholly-owned subsidiary of Galactic Resources, Ltd of Vancouver, Canada ran a large tonnage open-pit mine and cyanide heap leach operation from 1986 to 1992 (Pendleton and Posey, 1992) During the mine operation by SCMCI, approximately 10 million tons of gold ore was mined, crushed and stacked on a lined leach pad. Heap leach operations experienced water balance and unplanned solution discharges from the start of the mine life. Despite the production of 249,000 troy ounces of gold during the mine operation, SCMCI was unable to meet remedial requirements and notified the state of Colorado of its intention to file a Chapter VII bankruptcy in December 1992. The EPA Region VIII Emergency Response Branch took over site operations on December 16, 1992 to prevent a catastrophic release of hazardous substances to the environment. The multiple contamination sources at the mine site are due to both historic and SCMCI mining operations. Emergency response operations at the site have prevented releases of severely contaminated solution and a permanent treatment for all waste units at the site is under investigation. A Request for Proposal (RFP) was issued in October 1993 by Environmental Chemical Corporation (ECC) at the Request of EPA Region VIII, Department of the Interior and Bureau of Reclamation. The RFP requested that interested companies provide information on their ability to implement innovative treatment technologies to improve treatment efficiency and reduce treatment costs for remediation of the heap leach pad (HLP) spent ore and ore leachate solutions. Dames & Moore and Pintail Systems, Inc. (PSI) jointly submitted a proposal suggesting application of biotreatment processes for detoxification of cyanide in spent ore and HLP leachate solutions. The proposal was accepted for pilot and field demonstration under the SPA Superfund Innovative Technology Demonstration Program (SITE) with additional funding from EPA Region VIII. This report discusses the test program and results of a Focused Feasibility Study which demonstrated biotreatment processes for spent ore cyanide detoxification.

Jan 1, 1995

By Al. Valero

This paper quantifies in universal units (energy units), the annual decrease in the mineral endowment of the planet. This is done for some important extracted non-fuel minerals, namely aluminium, cobalt, chromium, copper, gold, lead, uranium and zinc and is compared with the depletion figures of conventional fossil fuels. The results of this study reveal that each year, the decrease of the global non-fuel mineral bonus provided by Nature is 2 to 3 orders of magnitude greater than the loss associated to the burning of fossil fuels. Particularly for 2008, the depletion in mineral wealth of the studied commodities was about 20 times greater than that of fossil fuels. The assessment methodology is based on the Second Law of Thermodynamics. It quantifies the useful energy (exergy) required to concentrate a mineral from a completely dispersed state in the crust, to the conditions of composition and concentration found in the mines. Exergy can be a useful measure for quantifying the mineral depletion caused by man, as it takes into account the main physical features that make minerals valuable: composition and concentration. This analysis enhances and puts numbers to the importance and necessity of material reuse and recycling.

Jan 1, 2011

By P. Venkatsubramanian, D. R. Maneval

An insufficient hydrologic data base exists for most large and small coal basins in Alaska owing to the lack of need in the past to collect data. The runoff process is insufficiently understood which is complicated by specifically northern phenomenon, and the lack of understanding of hydrologic relationships in permafrost environment. This paper presents an understanding of the hydrologic effects of frozen ground and presents methods by which the influence of surface mining upon the hydrologic balance can be analyzed.

Jan 1, 1987

By Dao De Xu, Heechan Cho, Mark S. Klima

A study was conducted to determine the feasibility of using dense-medium centrifugation for separating fine (-150 µm) coal. A centrifuge provides the capability of varying the rotational speed and retention time independently, which offers the potential for a higher degree of control as compared to a dense-medium cyclone. Tests were conducted with a 140-mm diameter by 76-mm long Plexiglas separator, which was fitted with appropriate feed and discharge pipes to allow continuous separations to be made. A suspension of ultrafine (-10 µm) magnetite and water was used as the dense medium. The effects of operating conditions, including the magnitude of the 'g"-force and retention time, on centrifuge performance were investigated.

Jan 1, 1995

By Mel J. Laurila

The application of on-line ash analyzers in coal processing has become widespread. However, the analyzers are employed largely in monitoring, blending or sorting applications. Just recently has work begun on using on-line ash, moisture and/or solids data for plant control; and even more recently for localized circuit or unit operation control. Process Technology, Inc. (PTI) has since 1990 placed several bulk coal and slurry analyzers in practice where Fuzzy Logic Control (FLC) loops are used to manipulate controllable variables in real time. This technology is now being advanced by PTI. Unit operations where FLC has been employed in feedback loops using on-line ash analyzers include: heavy media vessels, cyclones, concentrating tables and froth flotation. The design, implementation and improvements attainable in preparation plant control using on-line ash analyzers are outlined in this paper.

Jan 1, 1995

Little knowledge is available that considers the effects of continuous miner position on the possible respirable dust exposure of the remote mining-machine operator. Such information could be very useful for increasing the awareness of the remote operator as to those parts of an extended cut that generate higher levels of respirable dust. This data could be used to develop guidelines for positioning the remote operator to reduce his potential exposure. This work details the effects of continuous miner position on dust levels measured on the machine and at the remote continuous miner operator location.

Jan 1, 2000

By Ed H. Wipf, Kurt L. Bryan, O&apos

Flow sheets employing SAG Mills as the initial stage of grinding are commonly selected for comminution of ores. Several alternative technologies are available. The paper will provide a brief review of the latest alternatives to SAG mills. Included in this review will be a discussion of the comparable benefits of each technology. Commonly accepted disadvantages will also be presented.

Jan 1, 1998

By Gülhan Özbayoglu, Yusuf Ziya Akgök

The effect of cooling rate on the flotation behaviour of copper slags of flash smelter plant in Samsun was investigated. Fresh molten slag was solidified in laboratory scale in three different ways. All the samples were characterized by chemical and mineralogical analyses. The chemical analyses showed that samples prepared from fresh slag had 0.9 to 1 % Cu with 40 % Fe and 30 to 32 % SO2. Old pit slag samples contained between 1 to 3% copper. Microphotographs showed that rapidly cooled slags showed fine size distributions, e.g. the copper grains in granulated slag had sizes in 1-2 microns. On the other hand, the size of copper grains in slowly cooled slags increased above 40 microns. Flotation tests carried out by using potassium amyl xanthate and Flotanol-C showed that slowly cooled slag reduced the copper losses in the tailing and improved the grade of concentrate. Under the light of laboratory investigation, the pit dimensions of Samsun Plant have been modified which resulted in a pronounced improvement of the grade and recovery of concentrate produced at Samsun slag flotation circuit.

Jan 1, 1995

By K. Hanumantha Rao, K. S. E. Forssberg

The separation of feldspars from quartz has been the subject of numerous studies since 1930 and the flotation process so far proved to be the most suitable method. In the conventional process, feldspars are separated from quartz using a cationic collector and hydrofluoric acid as an activator of feldspars. There is no general agreement on the mechanism of fluoride activation of feldspar surfaces and the role of fluoride ions is briefly discussed. The use of HF is no longer acceptable due to environmental and health problems, and a few new reagents schemes have been reported. The available evidence shows that the success of these new reagent schemes is very limited. A new reagent scheme which is environmentally safe and cost effective for the separation of feldspars from quartz is yet to be resolved.

Jan 1, 1994

By J. P. Rider, T. W. Beck, J. A. Organiscak

"The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR) has recently developed a series of models utilizing Computational Fluid Dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models utilizing Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The following scenarios are considered in this study: 100% of the discharge redirected back towards the face on the off-curtain side of the continuous miner; 100% of the discharge redirected back towards the face, but divided equally to both sides of the machine; and 15% of the discharge redirected toward the face on the off-curtain side of the machine, with 85% directed into the return. These models were compared to a model with a conventional scrubber discharge where air is directed away from the face into the return. The CFD models were calibrated and validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100% redirected, equally divided case. These models identified relatively high gassy areas around the continuous miner which may not warrant their use in coal mines with medium to high methane liberation rates. This paper describes the methodology used to develop the CFD models, and the validation of the models based on experimental data.INTRODUCTION Methane gas and respirable dust are two hazards frequently encountered at continuous miner (CM) operations. An accumulation of both methane gas and coal dust may lead to massive explosions underground [1], and overexposure to respirable coal dust can result in pneumoconiosis (commonly referred to as “Black Lung Disease”) in coal workers [2]. Current U.S. federal coal mine regulations limit concentrations of methane gas to below 1% at the face area and require exposures to respirable coal dust to be at or less than 2.0 mg/m3 for an 8 h shift average. Begin on August 1, 2016; the overall respirable dust standard in coal mines is reduced from 2.0 to 1.5 mg/m3 for full shift sampling. If the quartz content of the dust exceeds 5% by weight, the dust standard becomes more stringent, reducing the allowable concentration to the value of 10 divided by the % quartz."

Jan 1, 2015

By S. Kesler

Rössing Uranium Limited has operated since 1976 a large open pit uranium mine and extraction plant at a remote site in the Namib desert, South West Africa/Namibia. The geology (Berning, I., et al. Economy Geology) and the technical aspects concerning mining, grade control and metallurgy have previously been described (Rössing Uranium, Mining Magazin and Whyllie, R.J.M. "Rössing Uranium reaches rated production", World Mining). The improvement of leach 'extraction has been reported in 1984 (Kesler, S.B. et. al. "Uranium extraction at Rössing") and the installation of a central process control system has been described (Kesler, S.B. et al. "The introduction of a central process system at Rössing"). At the beginning of 1983 a decision was made to develop a computer system for metallurgical plant optimisation which included mass and volumetric balances, analytical assays for up to 5 chemical elements and the costs for the major consumables. Within 10 months this computer system was developed and implemented. A large number of test runs were made and computer studies were undertaken. The metallurgical division now has a scientific tool for production; planning for actual comparison with plant results and for strategic investigations and decision making.

Jan 1, 1986

By Patrick R. Taylor

This paper presents a fundamental study of the thermodynamic and kinetic effects of copper and iron on gold-cyanide leaching. It quantifies the solubilities of the impurities, complex formation, and kinetic effects. The necessity of solution recycle, to meet environmental standards, requires that fundamental information be generated to characterize behavior and allow the identification of treatment methods. Mathematical descriptions of both solubilities and kinetics will be presented

Jan 1, 1983

By Jae-Chun Lee, Sadia Ilyas

"The present study was carried out to develop an economically feasible and environmentally friendly technique to extract metals such as Al, Fe, Cu, Zn and Ni from electronic scrap by employing Penicillium chrysogenum strain KBS3. Studies were carried out in various leaching modes, including one-step leaching with combined growth and leaching phases (Mode 1), two-step leaching with alternative growth and leaching phases (Mode 2), spent medium leaching with separated growth and leaching phases (Mode 3), leaching with fresh growth medium without fungal culture (Mode 4), leaching with deionized water (Mode 5) and leaching with commercial organic acids (Mode 6). The main lixiviants produced in leaching Mode 1 were citric, tartaric, oxalic and gluconic acids in concentrations of 12, 2.5, 1.8 and 152 mM, whereas in leaching Mode 2, the concentrations were 15, 0.5, 1.0 and 1,162 mM, respectively. In leaching Mode 3, 63 mM citric acid, 23 mM tartaric acid and 29 mM oxalic acid was observed. At 5% pulp density, both leaching Modes 1 and 2 showed similar metal extraction yields from the electronic scrap at 35º C. Approximately 96% Al, 98% Zn, 48% Cu, 25% Fe, 66% Pb and 73% Ni were extracted in leaching Mode 1 in 14 days. In leaching Mode 3, 85% Al, 81% Zn, 97% Cu, 22% Fe, 50% Pb and 63% Ni were extracted in 14 days. The extraction yield of Cu was much lower in leaching Modes 1 and 2 (48- 50%) than in leaching Mode 3 (97%), as well as in leaching Mode 6 (98%) with organic acids, including citric, tartaric, oxalic and gluconic acids.IntroductionTechnical innovations in electrical and electronic equipment with new functionalities and designs stimulate consumer purchasing and lead a rapid increase in the production of waste materials. Terazono et al. (2006) have reviewed the data on electronic waste generation in different parts of the world. Studies by Bertram et al. (2002) have also affirmed that waste electrical and electronic components are the fastest growing waste category, which emphasizes the need for efficient recycling strategies. The recycling of electronic waste is an important subject, not only from the perspective of waste treatment, but also from the perspective of the recovery of valuable materials. However, the recycling of electronic scrap is still limited, due to the heterogeneity of the materials present in the products (Veit et al., 2005).Bioleaching-based processes offer a number of advantages over conventional pyro or hydrometallurgical methods (Lee et al. 2007; Lee and Pandey, 2012). These advantages include simple, inexpensive (in some cases) and ecofriendly approaches and the generation of less active leach residue relative to other metallurgical processes. Although biohydrometallurgical processes have been successfully applied to the leaching of metals from ores (Olson et al., 2003; Rawlings, 2002), data pertaining to the application of these processes for the extraction of electronic scrap are still scarce. Recently, a few studies have been undertaken for the extraction of metals from electronic scrap/ printed circuit boards (Brandl et al., 2001; Faramarzi et al., 2004; Ilyas et al., 2007; Ilyas et al., 2010). These studies were conducted with mesophilic chemolithotrophic bacteria (Acidithiobacillus ferooxidans and Acidithiobacillus thiooxidans), cyanogenic bacteria (Chromobacterium violaceum) or moderate thermophilic bacteria (Sulfobacillus thermosulfidooxidans). However, compared to bacterial leaching, fungal leaching has several advantages, including (i) the ability to grow at a higher pH, thus making it more suitable for the bioleaching of alkaline solid waste; (ii) a generally faster leaching process with a shorter lag phase and (iii) the chelation of excreted metabolites (e.g., organic acids) with metal ions, thus reducing toxicity to the biomass (Burgstaller and Schinner, 1993; Aung and Ting, 2005)."

Jan 1, 2015

By M. Yekich, W. R. Reed, G. Ross, A. Salem

"Canopy air curtain (CAC) technology has been developed by the National Institute for Occupational Safety and Health (NIOSH) for use on continuous miners and subsequently roof bolting machines in underground coal mines to protect operators of these machines from overexposure to respirator coal mine dust. The next logical progression is to develop a CAC for shuttle cars to protect operators from the same overexposures. NIOSH awarded a contract to Marshall University and J.H. Fletcher to develop the shuttle car CAC. NIOSH conducted laboratory testing to determine the dust control efficiency of the shuttle car CAC. Testing was conducted on two different cab configurations: a center drive similar to that on a Joy 10SC32AA cab model and an end drive similar to that on a Joy 10SC32AB cab model. Three different ventilation velocities were tested—0.61, 2.0, 4.3 m/s (120, 400, and 850 fpm). The lowest, 0.61 m/s (120 fpm), represented the ventilation velocity encountered during loading by the continuous miner, while the 4.3 m/s (850 fpm) velocity represented ventilation velocity airflow over the shuttle car while tramming against ventilation airflow. Test results showed an average of the dust control efficiencies ranging from 74–83% for 0.61 m/s (120 fpm), 39–43% for 2.0 m/s (400 fpm), and 6–16% for 4.3 m/s (850 fpm). Minor modifications to the shuttle car CAC design and placement improved the dust control efficiency to 51–55% for 4.3 m/s (850 fpm) with minimal impact on dust control efficiencies for lower ventilation velocities. These laboratory tests demonstrate that the newly developed shuttle car CAC has the potential to successfully protect shuttle car operators from coal mine respirable dust overexposures. INTRODUCTION The development of the canopy air curtain (CAC) dates back to the 1970s starting with the initial development of the CAC by the Donaldson Company, Inc. under contract from the U.S. Bureau of Mines [Krisko 1975]. This CAC was originally developed for continuous miner operators when continuous mining machines had cabs. The need for a CAC on the continuous miner was eliminated when the cab was removed from the machine design. However, CAC development progressed to include CAC designs for a roof bolting machine to protect roof bolters from respirable coal mine dust [Goodman and Organiscak 2002, Listak and Beck 2012, Reed et al. 2017]. This roof bolting machine CAC research continues to the present day."

Jan 1, 2018

By Roe-Hoan Yoon

Froth flotation is widely used for separating particulate materials from one another in aqueous media. The basis of this important separation process is to control the hydrophobicity of particles. However, it is difficult to predict the kinetics of flotation based on contact angle (?), which is a thermodynamic property. A solution to this difficulty would be to develop a relationship between ? and the gradient of the hydrophobic forces across the solid-liquid and bubble-liquid interfaces. Such information can be obtained using the surface force apparatus (SFA), the atomic force microscope (AFM), and the thin film balance (TFB). The present communication reviews the results of the measurements conducted using these methods, and offers a methodology for deriving a rate equation for bubble-particle interactions

Jan 1, 1999

By K. A. Natarajan, M. K. Yelloji Rao

The electrochemistry of sphalerite and chalcopyrite was investigated under both open-circuit and applied potential conditions. Emphasis was placed on the selective dissolution of sphalerite from a mixture of sphalerite-chalcopyrite flotation concentrates as a function of applied potential, acid concentration, pulp density, and time. Morphological studies using a scanning electron microscope (SEM) were also carried out with chemically leached, galvanically leached, and unleached surfaces of sphalerite and chalcopyrite. Selective dissoulution of sphalerite could be achieved if the mixed chalcopyrite-sphalerite concentrate slurry was maintained at a negative applied potential of -0.4V (SCE). Probable mechanisms involved in the selective dissolution of zinc are disscussed.

Jan 1, 1990

By W. J. Adamson

Strategic Data Planning (SDP) is an emerging technique for the analysis and design of information systems. This paper describes the use of strategic data planning in the formulation of a complete integrated set of mining technical systems for the Koolan Island iron ore mine. Applications covered include hydrogeology, geology, mine planning, surveying, quality control, laboratory and mine production recording. Koolan Island is 13 kilometres long and 5.5 kilometres wide at its widest point. Its sole industry is an open pit iron ore mine of 3 million tonnes annual capacity, owned and operated by BHP Minerals. Some of the production is used by BHP Steel International, but most is exported. The orebody is steeply dipping and is mined bench by bench. Outturn grades for run-of-mine product are iron 66.5%, silica 3.0%, alumina 1.0%. Computer systems are run on Data General equipment, currently an MV10000. Computer applications, which are shared across mine sites, are developed and maintained by BHP Information Systems in BHP's Melbourne Office.

Jan 1, 1986