Search Documents

By Daniel Tao, Jike Qiao, Hao Ren, Feifei Ji, Gonglun Chen

The floatation of niobite was studied using a number of collectors at various dosages and solution pH’s. Octyl diphosphonic acid was found to be an effective collector for niobite flotation with good selectivity. A flotation recovery of 91.2% was obtained with 140 mg/l octyl diphosphonic acid at pH’s less than 5.0. Infrared absorption spectroscopy (IAS) and X-ray photoelectron spectroscopy (XPS) were used to characterize the interactions of niobite with octyl diphosphonic acid. Species distribution diagram of octyl diphosphonic acid and niobium species was used to elucidate the flotation behavior of the mineral with octyl diphosphonic acid. A chemical adsorption mechanism of niobite with octyl diphosphonic acid was proposed. Keywords: octyl diphosphonic acid, electrokinetic measurements, niobite flotation, XPS.

Jan 1, 2005

By A. Supomo, A. Partanen, M. Mular

Although many SAG operators may agree that on-line measurement of SAG feed-size is an attractive notion, applying this information in a control strategy that recovers the investment, engineering time, and maintenance is not necessarily straightforward. The P. T. Freeport Split-Online system was justified based on the assumption that SAG feed-size could be used in a feed-forward control strategy either at the regulatory or expert system control level. Something like “as the feed size changes adjust the throughput to avoid under or overloading the mill” was envisioned. However, following installation and calibration, Cluster Analysis showed that such an approach would not be successful. However, the sensor has been successfully integrated into Freeport’s grinding control strategy other ways. It provides an input to the Kalman filter parameter estimator used in a model-based control strategy that optimizes throughput and grind. The Split sensor also provides a characteristic feed size parameter for use in an on-line work index estimator. This paper describes the calibration and installation of the Split SAG feed-size analyzer, and reviews the evolution of its use in the Freeport C3 grinding circuit control strategy.

Jan 1, 2001

By S. Gallagher, A. Mayton

Introduction The mining industry has long been associated with a high incidence of low back disorders and pain (Klein et al. 1984, Leigh and Sheetz 1989, Brinckmann et al. 1998). It is believed that the higher incidence of these injuries among miners is the result of high exposures to postural demands, heavy manual work, and exposure to whole-body vibration (WBV). Recent work has indicated that miners involved with heavy lifting (especially in restricted spaces or on uneven ground) or who have been exposed to whole-body vibration in undamped seats experience noticeable changes in their spines that are consistent with degeneration of the intervetebral discs of the spine (Brinckmann et al. 1998). As will be described shortly, there is mounting evidence that disc degeneration plays a large role in the development of low back pain, particularly chronic back pain. Until fairly recently, medical doctors generally assumed that back pain was the result of muscle strain, ligament pain, or so-called “trigger points” (Bogduk, 1997). However, research supporting these mechanisms of pain has been very scant. When subjected to scientific scrutiny, none of these mechanisms has been shown to relate to back pain in a convincing manner. On the other hand, there are three mechanisms that have been shown to be highly associated with back pain in controlled scientific studies: sacroiliac pain (present in 13% of back pain sufferers) (Maigne et al. 1996), facet joint pain (present in 15 % of back pain sufferers) (Schwarzer et al 1994), and disc disruption and degeneration (present in 39% of chronic back pain sufferers) (Moneta et al. 1994). The latter mechanism, which bears the highest relationship to back pain that has been objectively demonstrated, will be the focus of this section. Scientists now believe they have a good idea how back pain may develop in cases involving disc disruption and degeneration (Bogduk 1997). As the spine experiences loading during lifting tasks or whole body vibration, the first structure to fail is called the vertebral endplate, which is a structure that attaches the disc of the spine to the vertebral body (Figure 1). The endplate typically experiences a fracture, which the body will attempt to heal by means of scar tissue. Unfortunately, this scar tissue impedes the flow of nutrition to the disc itself (discs are dependent on nutrition from the vertebral bones), and if the supply is reduced sufficiently, the disc will start to degenerate. As this degeneration process proceeds, fissures or tears in the fibers of the disc start to develop. If any of these tears is a grade 3 fissure (Figure 2), an inflammatory response occurs in the disc, which will lead to the well-known sensation of low back pain (Peng 2006).

Jan 1, 2007

By Steve Kral

The Society for Mining, Metallurgy and Exploration’s origins can be traced back to 1871. This was when 22 Pennsylvania coal mining engineers founded the American Institute of Mining Engineers (AIME). The organization’s objective was to “promote the arts and sciences connected with economic production of the useful minerals and metals, and the welfare of those employed in those industries by all lawful means.” Metallurgy and Petroleum were added to the AIME name in 1919 and 1956, respectively. Divisions of AIME were formed throughout the following years in recognition of the increasing trend toward specialization among mineral industry engineers. At the time, SME’s divisions consisted of the Coal Division (1930, now known as the Coal and Energy Division), the Industrial Minerals Division (1935), the Mineral and Metallurgical Processing Division (1948) and the Mining and Exploration Division (1949). The Environmental Division was created in 1997.

Jan 1, 2007

By V. Osterholt

Sustainable development of mineral resources is based on a spatial model of the orebody that is only partly known from exploration drilling and associated geological interpretations. As a result, orebody models generated from the available information are uncertain and require the use of stochastic conditional simulation technique. This paper considers three methods for simulating orebody geology: (1) pluri-Gaussian simulation that limits the allowable contacts between the various units; (2) sequential indicator simulation using indicator kriging; and (3) an experimental multiple-point approach that captures some higher-order spatial statistics. The data requirements of the methods, how to meet them in mining applications, and performance characteristics are discussed. The application of these methods in a hypothetical deposit consisting of three geological units provides a comparison and illustrates the advantages of the different simulation approaches.

Jan 1, 2005

By H. -J. Langhoff

"The paper describes not a result, but a starting point to implement sustainable development to a region characterized by a typical down river landscape, agriculture, and extractive industry. The NaturFreizeitNiederrhein GmbH (NFN) is a private company with associates from administrative bodies, the local mining companies and multiple representatives of environmental protection groups (local and national), tourism organizations, cultural societies and also aquatic sport and fishing clubs. Center of the concept is the "NFN Lake District." The development concept aims to provide the agricultural industry with alternative means of income, while protecting wildlife and the ecological balance as well as preserving the social und cultural system and enhance the safety against flooding from the river Rhine. The mining industry contributes their coordination of obligation concerning reclamation and recultivation of the already existing individual projects. While designing the landscape components and establishing the infrastructure for the different tasks, the production of gravel and sand is yield as a by product. The result is a long term perspective for region and industry."

Jan 1, 2005

By K. C. Tran

This paper reviews the advancement of measurement technologies for the control of raw materials processes in the basic industries. The combination of digital technology and on line spectroscopy enables the development of intelligent instruments for composition and particle size analyses in real- time high- frequency control conditions. In many industries, the applications result in productivity improvement and energy savings. Plant specific examples include operating experience and benefits realized in sorting, blending and beneficiation processes. Instruments of the future not only measure specific parameters of the process and monitor its own health combined with self-corrective mechanics but also acts with intelligence to effect the quality of the process or regulate the primary apparatus.

Jan 1, 2001

By K. E. Kolm, W. H. Langer

Developing natural aggregate resources (sand, gravel, and stone) creates environmental impacts. A systems analysis method has been designed to characterize the components of the environmental system, identify potential impacts to those systems, and evaluate the extent of those impacts. The step-wise method consists of problem definition, data collection, preliminary conceptualization and characterization, additional data collection, data analysis, and refinement. The method requires analyzes of various systems making up the environment, including land surface, geomorphic, subsurface, and groundwater systems. After system characterization is complete, the method focuses on identifying and evaluating potential environmental impacts to determine acceptable mining strategies.

Jan 1, 2001

By William R. Yernberg

The 2006 North American Tunneling (NAT) Conference was held June 10-15, 2006, in Chicago, IL. The biennial conference was the first NAT conference by the newly formed Underground Construction Association of SME (UCA of SME). The UCA of SME was formed earlier this year at the request of members of the American Underground Association (AUA) (ME, April 2006, page 75). The conference included a keynote session, technical programs, workshops, a trade show and social activities. The conference exceeded expectations with 570 attendees. They included engineers, equipment manufacturers, representatives from government agencies and other interested individuals in the underground construction industry. The trade show was also a success with more than 86 booth spaces sold. Vendors included the biggest names in the underground construction and tunneling industry and included equipment manufactures, construction contractors and engineering companies. The trade exhibition provided a forum for interested parties in the tunneling industry to meet and discuss services, equipment and techniques.

Jan 1, 2006

By J. Pesl, R. Hurman Eric

Metal-slag phase compositions of molten iron and ilmenite smelting slags or solid titanate phases were determined between 1500° and 1700°C. The influence of oxygen partial pressure and impurity oxide additions including Al2O3, Cr2O3, MgO and SiO2 were investigated along with amount of reductant-carbon. The XRD revealed that the quenched slag crystallized as pseudobrookite (M3O5) solid solution in equilibrium with iron. Silica additions formed separate silicate phases because of its immiscibility in the titanate phase. Under strong reducing conditions iron oxide was almost completely reduced and the slag phase solidified as a consequence thereof. Cr2O3. SiO2 and MnO were also reduced to a high degree. Under weak reducing conditions the slag was fully molten and non of the impurity oxides were reduced. A significant portion of manganese, some magnesia and silicon, in the form of SiO gas, were removed via the gas phase due to their considerable vapour pressures. Alumina was not reduced under the applied conditions. A comparison of the experimental results with industrial data clearly suggested that industrial ilmenite smelting process operated under non-equilibrium conditions.

Jan 1, 2005

By K. Wenrich

The uranium industry has made a dramatic turnaround in the past three years that even the most optimistic economist was not willing to predict during the uranium downswing of the 1990s. Uranium reached a 30-year low in February 2001 of $6.50/lb. By the end of February 2006 it had soared to $38.50/pound. This nearly 600% increase in the uranium spot price within 4 years dwarfed the increase in gold price that has barely mustered a 100% increase. The initial slow rise from $6.50 in February 2001 to $10.75 in April 2003 (fig. 1) was primarily driven by the decrease in the value of the dollar. Since then several factors have contributed to the soaring price: (1) The awakening of many to the simple fact that uranium supply has not met demand for several years and that the world’s stockpiles are being drawn down, (2) How sharply this fragile supply can be impacted by disasters at the world’s major uranium production facilities, such as a) the flooding of the McArthur River Mine in the spring of 2003, b) fires at Olympic Dam, c) the potential that Rossing, with an annual capacity of 4000 tonnes uranium might close by 2007, (3) the withdrawal of Tenex from the HEU (highly enriched uranium) feed agreement, and (4) the announcement by the Chinese of their intent to build 30 new nuclear reactors.

Jan 1, 2007

By R. Thornton

Montana Tech is located in the historic mining town of Butte, MT and is adjacent to the Orphan Boy mine. This abandoned underground mine will be the heat source for a down-hole heat exchanger (DHE)/heat pump system. The mine was abandoned in the 1950?s and has since filled with water to within approximately 30 m of the surface. The shaft is composed of a 245 m vertical shaft connected with horizontal crosscut drifts at 60 m and 150 m below the water level that connect to a large stope with approximately 1250 million liters of water at a consistent 75-78°F temperature. The intent is to build this heating system to augment or fully heat a newly built 2,000 m2 building on the Montana Tech campus. As designed the system uses ?off-the-shelf? parts making the basic configuration straightforward with the exception of the DHE?s which need to be placed into the vertical shaft. Because there is little or no examples of placing the heat exchangers in a vertical shaft, the primary focus of this work was to model the heat exchanger placement and configuration in the vertical shaft such that thermal currents develop between the stope and vertical shaft in, via the horizontal crosscut drifts, in order to move the water and thereby provide the required energy. This study includes the modeling of water flow, temperature profiles, and the heat contribution from the surrounding rock walls.

Feb 27, 2013

By Matthew Wallin

A part of the East Bay Municipal Utility District?s Folsom South Canal Connection Project, 430 feet of raw water pipe was installed using micro tunneling beneath the Mokelumne River. The access shafts for this crossing were constructed 50 and 35 feet deep through very dense sands and soft sandstone and siltstone. High groundwater and the immediate source of recharge from the river required watertight shaft construction methods. The shaft contractor, Drill Tech of Antioch, CA, used a brand new Bauer cutter-soil mixing (CSM) rig to construct the large shafts. The structural concept is similar to secant piles, but instead of creating cylinders of soilcrete, the CSM rig creates interlocking rectangular panels. This technology has been used previously in Europe, Asia, and Canada, but this was the first project to use CSM technology in the United States. Cutter-soil mixing technology has other applications beyond shaft construction, including retaining wall construction and levee reinforcement.

By Michael Jatczak

The San Vicente Tunnel Project is an 11-mile water tunnel constructed for the San Diego County Water Authority. One of the many challenges of the project included tunneling a 22,000-foot single-heading tunnel on the western half of the job in varying geology using a 3.66m (12ft) diameter open shield excavator or ?digger shield.? This paper will discuss the design considerations for the temporary liner, the tunneling, and ancillary equipment. It will also highlight the challenges faced while mining this geology, explain the methods implemented to drive this section of tunnel, and discuss the experiences while performing mechanized tunneling in an extensive and varied San Diego geology.

By James J. Graham

Uravan, Ambrosia Lake, Gas Hills and South Texas are all historic names in US uranium. These mining areas supplied the uranium that brought the United States into the nuclear age during the 1960s, and fueled the birth of nuclear energy for peaceful uses — a promise of nearly limitless, clean energy for the world’s future. That promise still exists today, but it is hard to hear over the rhetoric of environmental activists and politicians. Nuclear power offers dependable electricity with limited environmental impact at stable prices. Nuclear power releases no greenhouse gases or particulate matter into the atmosphere. High level nuclear waste (HLW), although long lived, is readily controlled and compact. In the United States, generating 1 billion kWh of electricity with coal produces 47 kt (52,000 st) of solid waste (ash and sludge), compared to 3.6 t (4 st) of HLW produced by nuclear.

Jan 1, 2002

By K. Fleck

Energy West Mining Company (EWMC) has implemented a geologic program for improving stability and support requirements along deep two-entry longwall gateroads at its Deer Creek Mine operations located near Huntington, Utah. Together with geotechnical monitoring and concurrent review of mine seismicity in cooperation with MTI staff, it has become possible to improve longwall layout designs for two seam extraction of the Hiawatha and Blind Canyon seams. The geologic program consists of surface and in-mine exploration drilling, surface and in-mine geologic mapping, rock mechanics testing and detailed measurements of changes in depositional and structural conditions during development of every longwall gateroad. The geotechnical program consists of underground measurements at seven locations in two neighboring mining districts located in the Hiawatha and Blind Canyon coal seams under moderate to deep cover. Within the last five years, additional measurements, including data on seismicity and face conditions, have been incorporated into the data collection program for verifying the insitu coal strength and load transfer mechanisms for improving two-seam designs and support systems. Geologic mapping results are also used to predict local stability of headgate and tailgate entries, combining mine roof mapping, stratigraphic profiles of the coal and roof, and depth-of-cover information and dual-seam mine overlays, for use by operations personnel in planning roof and rib support for the retreating longwall sections.

Jan 1, 2012

By D. Hopkins, D. Türler, R. D. Giauque, W. B. Davis, M. Karaca

In a highly collaborative research and development project with mining and university partners, sensors and data-analysis tools are being developed for rock-mass characterization and real-time measurement of mineral content. Determining mineralogy prior to mucking in an open-pit mine is important for routing the material to the appropriate processing stream. A possible alternative to lab assay of dust and cuttings obtained from drill holes is continuous on-line sampling and real-time x-ray fluorescence (XRF) spectroscopy. Results presented demonstrate that statistical analyses combined with XRF data can be employed to identify minerals and, possibly, different rock types. The objective is to create a detailed three-dimensional mineralogical map in real time that would improve downstream process efficiency.

Jan 1, 2002

By Leigh Freeman

This article provides an overview for a series of leadership development workshops offered through the SME Young Leaders Program. The first of these workshops, “Accelerated Development Plan,” will be held at the upcoming SME Annual Meeting in St. Louis, MO on Sunday, March 26. How does a foundation of technical competencies relate to the development of social competencies necessary for management and leadership roles in the resource sectors? Technical competencies provide the foundation for a successful career. Social competencies provide the framework on that foundation. Successful leaders will be those who develop competencies in all areas.

Jan 1, 2006

By Y. Wang, E. Forssberg, A. Johansson, B. Chan

A super-conducting high gradient magnetic separator with matrix vibration in dry separation mode is a powder purification device, which has been used to remove weakly magnetic impure particles from fine calcite powders below 53 µm in this study. A fundamental question concerned is the evolution of the matrix clogging under gas-solids loads. This paper presents the improvement of the separation selectivity using a method of mechanically based vibration on the matrix in the separator. The functions of the matrix vibration are discussed. The results indicated that the mechanically based vibration on the matrix within a high intensity magnetic field while a feed was introduced in an air stream, was found to be effective for the dry purification of fine powder materials.

Jan 1, 2001

By S. G. Dixit

Alunite (KAl3(SO4)2(OH)6] is one of the important nonbauxitic resources for aluminum in U.S.A. The major gangue material associated with a unite ore body is quartz. Experimental results indicate that oleic acid flotation of alunite is quite effective in upgrading the ore. The flotation chemistry of the alunite/oleate system has been investigated using various techniques such as: hallimond tube flotation response, measurement of adsorption density using I4C labeled oleated, electrokinetic measurements, infrared spectral studies, contact angle measurements and thermochemical measurements using an isothermal microcalorimeter. Alunite has been found to float readily with oleate in the pH range 4-10.5 and its flotation response is enhanced at higher temperatures. The PZC of alunite has been determined to be at pH 7.2 ± 0.15 which agrees with what would be predicted from solution chemistry and from the flotation response with physically adsorbed collectors. Infrared spectra show a specific peak in the range 1585-1600 cm-1 which has been attributed to the formation of an aluminum oleate surface species. Both adsorption density measurements and infrared spectra indicate that during adsorption multilayers are formed. The heat of adsorption of oleate on alunite has been found to be endothermic and of the order of 4-6 KJ/ mole.

Jan 1, 1980