Search Documents

By Samuel Frimpong

In this paper, the authors present a typical mine profitability model. The method of generating system moments is used to examine the sensitivity of the profitability function to changes in the dependent variables, and to express the expected risk associated with undertaking the project in a predicted economic and technical environment. Profitability of a mining venture is a function of many variables ore grade, capital and operating costs, milling efficiency, ore reserve tonnage and annual tonnage, equity - loan structure, tax regime, etc. Estimates of the expected value and the variance of the profitability function are obtained by calculating the partial derivatives of the function with respect to the dependent variables, using the Taylor series expansion method to the second order. Sensitivity analysis is carried out by examining the effects of each variable on the profitability function, which is determined by the magnitude of the product of its partial derivative and variance. An appropriate probability density function, based on the expected value and the variance of the profitability function, is assumed to estimate the expected risk associated with the project. This expected risk is a measure of the area under the profitability density function below the appropriate, selected discount rate or the cut-off net present value (NPV). The results are compared with those obtained by using the Monte Carlo simulation technique, and they show that either of the two methods could be used to evaluate the probability of project failure or success with no significant difference.

Jan 1, 1992

By M. C. Williams

The dynamic behavior of batch mill, CSTR mill, and a closed grinding network consisting of a mill, sump, and cyclone was analyzed using the dynamic population balance model (PBM). The dynamic solution of the PBM of a batch, CSTR and a closed grinding network consisting of a mill, sump, and cyclone forms the basis of the dynamic analysis presented here. Two numerical dynamic solution approaches were used. These are: 1) providing additional constraints on breakage selection functions or 2) performing the Arbiter-Bhrany (or other) normalization of the selection functions. Actual experimental anthracite batch grinding data was used to obtain the functionality of the batch dynamic mill selection and breakage functions for a real physical system. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations is used to solve the batch dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. The mill, sump and hydrocyclone were modeled as a CSTR operating at various retention times. Batch dynamic PBM data was used to provide the mill kinetic and breakage selection function data. Different dynamic solutions were obtained depending on the numerical approach used. Each solution approach to a dynamic PBM with transport, while giving the same prediction for a single batch grinding time, gives different solutions or predictions for mill composition for other grinding times. This fact makes dynamic nodal analysis and control problematic. The fact that the constraint solution approach gives a solution may suggest that normalization for closed networks is not necessary. Differences in solutions to the PBM cannot be excused away by inaccuracies in the data used to model the grinding phenomenon.

Jan 1, 1995

By Greg R. Wheeler

Few members of the general public have a clear understanding of mineral resources. Most people do not know how minerals are mined or why they must be extracted from many diverse locations. Many people acquire knowledge of mineral development from mass media sources with incomplete details or obvious anti-mining bias. The California Mineral Education Foundation was formed in 1991 to provide educational opportunities for the public and industry. There have been major changes in earth science teaching requirements for kindergarten through 12th grade (K-12) curricula since the passage of California Senate Bill 813 in 1983. Model graduation standards, curriculum standards and the state science framework mandate substantial coverage of geoscience topics. The California State Commission on Teacher Credentialing has completed changes in multiple subject and single subject science credentials which will require more geoscience preparation for all teachers. The need for pre-service and in-service education in geoscience is at an all time high. Teachers must have continuing education to maintain their credentials and many are now seeking information in geoscience. The California Mineral Education Foundation designed and conducted the California Mineral Education Conferences held in August 1991 and 1992. The conferences involved lectures and field trips on mining geology, environmental problems and political concerns. Master teachers were employed to share how they get across mineral resource concepts in the classroom. Ninety-six percent of the participants stated that they had changed to a more positive perception of mining after taking the three day course.

Jan 1, 1995

A group of geologists is located in a remote area of North America, without telephone lines, electricity or even running water. They have spent days accumulating data for a mining company that is eager to receive any information about the dig. But the team does not have access to a wired communications infrastructure. So the geologists must wait until they get to the nearest town to transmit their data. TMI Communications has a mobile satellite communication system that allows geologists in the field to transmit their data from remote locations. The company's satellite is the heart of its North American mobile communications network. This satellite turns all of North America, including Canada, Mexico and the Caribbean into a single digital communications cell. Traditional terrestrial communications systems, such as dedicated phone lines or cellular systems, cannot handle a remote geological exploration camp's extensive communications needs. Cellular technology, where available, has high costs and limited applications. For geologists in the isolated areas of North America, accessible and reliable phone service is vital to success. For those who have established temporary camps, TMI Communications' satellite phone service has improved the speed and accuracy of their communications with home base. This wireless network is suited to meet the needs of existing data applications and the challenges of new ones. It can support any one- or two-way, fixed or mobile data transfer. TMI's network enables geologists to transmit exploration results, spreadsheet information and location co- ordinates to anywhere in the world, at any time. This is important if a team needs to relay vital data back to its headquarters to support immediate decision making on a prospect site or a find.

Jan 1, 1999

By Keith G. Wallace, Daniel J. Brunner

The traditional approach to mine ventilation planning involved making estimates of airflows, including leakage routes, and summing the corresponding pressure drops along consecutive paths in order to determine the fan pressures required. This methodology changed completely with the availability of computers. Mainframe digital computers began to be used for mine ventilation network analysis in the mid-1960's. Their use spread rapidly throughout the world in the 1970's. Mainframe machines were employed owing to the need for high speed numerical procedures and substantial storage requirements. However, during the past decade, the growing availability of low cost but powerful microcomputers has allowed the development of net- work analysis programs that can handle ventilation systems of hundreds of branches, and which can produce results within a few minutes. This paper discusses recent advances in software and hardware development specific to mine ventilation planning. Software developments include interactive data and output manipulation, graphical representation of output, internal checks on input parameters to preset ranges and subroutines which calculate the gas distribution throughout the network from known gas sources. Hardware advances have led to significant increases in memory to facilitate the analysis of large ventilation models, math co-processor chips which greatly shorten run times, and plotter hardware for graphical output displays. Recent software developments make it possible to graphically display output on printers faster than on standard plotters.

Jan 1, 1989

By Terry S. Maley

With some exceptions, minerals may be acquired on the unappropriated public lands by one of three methods: (1) mining claim location under the General Mining Law of 1872; (2) mineral lease under the Mineral Leasing Act of 1920; and (3) sale contract under the Mineral Materials Act of 1947. Leasable minerals such as oil, gas, coal and phosphate are specifically designated as leasable in the Mineral Leasing Act so the method of acquisition is clear. As a general rule, metallic minerals are acquired by mining claim location. However the nonmetallic minerals, most of which are industrial minerals or gemstones, present a more difficult problem. These minerals are acquired either by mining claim or a sale contract depending on their chemical composition, physical properties and the use to which they are put. The Act of July 23, 1955 (30 U.S.C. 61 1) provided that uncommon varieties of sand, stone, gravel, pumice, pumicite or cinders are locatable; whereas, common varieties of such minerals may only be acquired by a contract of sale. The widespread location of mining claims to appropriate such deposits has caused many land management problems. Federal court and Interior decisions offer the most useful guidelines in determining the most appropriate method of acquisition.

Jan 1, 1991

By R. D. Lama

Coal mining is one of the major sources of methane release to the atmosphere by human industrial activities and is believed to contribute to -30% of the total methane emissions from industrial activities. In 1993, world saleable black coal production, attained almost 3.5 billion tonnes from which around 65% was produced underground. Coal in underground mines can contain high quantities of methane and some deep coal seams have methane content as high as 50 cubic meters per tonne of coal. Gas is re- leased during coal mining from the mined seam and in a higher degree from the neighboring unmined seams and gas bearing strata which are fractured as mining advances. This paper de- scribes a study which was undertaken to estimate the extent of methane emissions from coal mining in the world. Measured emission related data were collected from most underground coal producing countries in the world. The data included methane flows in the ventilation system, methane flows in gas drainage system, in-situ gas content, methane utilization and coal production. More comprehensive data were collected from a range of gassy and non-gassy Australian mines. Residual gas content of samples from run of mine were also measured. Using the Australian data, mathematical expressions were established to evaluate methane emissions as a function of coal production and in-situ gas content for other mines. These emission models were then used to evaluate the emissions for the countries or coal basins without measured emission data. Trends in methane emissions from underground mining for the year 2000 and beyond were also estimated.

Jan 1, 1997

By John Clarke Holman

Industrial growth and survival in today's competitive world means both economic efficiency and technological superiority. Superior technology includes not only exploiting the best methodologies and techniques presently available, but also a continuous search for and development of, better ones. In practical terms this translates into an investment of substantial sums of money. Of course, even a relatively small investment will not be justified if the fruits of the project cannot be secured to the investor and the inventor alike. There are at least three ways to protect new or improved technology. If the improvement reaches the height of an invention, "patenting" usually is the preferred mode of protection. If, however, the improvement is novel and valuable but does not satisfy the requirements of the patent laws, one may then consider "trade secret" agreements as a means of obtaining appropriate return for the investment made so long as the improvement is capable of being maintained in secret and cannot be "reverse engineered." If one develops a new and useful organism and seeks immediate protection from infringers, current thinking is that the copyright law may afford such protection simply by publishing the genetic code. Here is one instance where you may publish without perishing! This paper will endeavor to highlight the pros and cons of various legal mechanisms and their applicability to the frontiers of technology.

Jan 1, 1985

By P. K. Crane, S. C. Gambrell

The work reported herein compares the support characteristics of two different types of roof truss subjected to the same force in the horizontal tension member. The major differences between the two trusses are in the sequence of tensioning the horizontal and inclined members and in the design of the loading brackets. A photoelastic model was used to compare stresses at points along the roof of the mine opening and at the junction of the roof surface and the rib. The effects of simulated subsidence on stress in the roof and on tension in the horizontal member were analyzed. Results indicate that there are significant differences in the overall support characteristics of the two trusses. Conclusions are drawn relative to which type of roof truss provides the most favorable support if the horizontal members are tensioned equally.

Jan 1, 1986

By R. C. Bryan, D. B. Jamison

This paper describes a procedure for minimizing the operational costs associated with blending sodium in coal at a surface mine in the Powder River Basin. Mine site blending is performed by adjusting daily production rates for high- and low-sodium pits. These adjustments are designed to produce a consistent sodium value called the blending target. The mine's contractual limit for sodium is sufficiently close to the field average value that any decrease in the sodium blending target may result in an opportunity cost, if the number of potentially minable tons is reduced. Conversely, any increase in the blending target may result in a higher sampling cost if more information is required to keep the blend within contractual limits. Blending parameters were defined using a geostatistical block model of sodium content that was based on analyses of hundreds of in-pit sample holes. Variograms for these data were used to compute the marginal costs of opportunity and sampling for a series of hypothetical in-pit drilling patterns. These marginal costs provided a basis for selecting optimum values for key parameters such as the blending target, production variance and in-pit sampling density. The benefit of implementing these optimized parameter values is that operational costs of sodium blending will be minimized over the long-term. At the mine where this procedure was developed, each dollar spent to increase the sampling density to the optimum value was shown to generate a $10 savings in opportunity cost.

Jan 1, 1991

The objective of this study is to classify ore and waste in a selected mine. The support vector machine, was used for the classification purpose, is applied to a zinc ore body in a skarn deposit located in the central region of the Peruvian Andes. The input parameters used for the model are spatial coordinates and the lithological information of the ore body. The input data was divided into training and testing data sets and the performance of the model was tested using the testing data set. The results show that more than 76% of the data could be properly classified by this method. The ore waste maps of the deposit was then developed using SVM model. From the result it was observed that a comparatively very few number of cells classified as ore. The ore is concentrated in small lodes at the middle of the volume of study, and not uniformly distributed throughout the study area. The lithological map of the deposit was also constructed as it was used as an input parameter for the SVM model. The indicator kriging was used for generation of lithological map of the ore body. Key word: Ore waste classification, Support vector machine, Indicator kriging, Confusion matrix.

Jan 1, 2008

By Felicia F. Peng

Two modes of collector addition techniques are applied in the column flotation for cleaning ultra fine coal. The collector can be: 1) added directly into the coal slurry through the feed system; and 2) gasified collector and transported in the gas phase through the bubbles. Operating parameters of the column flotation were investigated through three phases of work plans for Pittsburgh No.8 seam coal. In present study, the column flotation using two modes of collector addition techniques were tested and compared. Ninety percent or higher combustible recovery can be achieved by using both methods. However, utilizing the gasified collector addition technique in column flotation has more potential than direct liquid addition technique to obtain the higher recovery at same collector dosage.

Jan 1, 1993

By H. Ziock, J. Ruby, A. A. Johnson

Power generation systems that promote energy security and environmental benefits are highly desired and pursued by a number of government and industry programs. Gasification of coal, other fossil fuels, or biomass has the technical promise of high efficiency and low or zero emission. Gasification for the purpose of electrical power generation has been researched, developed and demonstrated over the last 20 years, but for many reasons is not viewed as economically competitive. This paper describes a coal-based gasification technology well suited to mid and long-term goals of secure, environmentally clean energy. The technology should be adaptable for use with other carbon-based fuels including biomass and a full range of fossil fuels. The new zero emission gasification process is sponsored by ZECA Corporation, a continuation of the Zero Emission Coal Alliance (ZECA). ZECA has completed process design and engineering to assess the viability of a concept originated at Los Alamos National Laboratory, and the creation of a business plan to define paths for advancing the technology toward a near-term goal pilot plant. The zero emission carbon (ZEC) technology includes hydrogasification, the production of hydrogen and the carbonation of lime with CO2. For the power generation base case, the hydrogen is used in high temperature coal compatible fuel cells to produce electricity and the carbonate is calcined to produce a pure stream of CO2for sequestration. This paper provides the status of work with the ZEC technology and the availability of crucial equipment, materials and required testing. Discussions are presented for future actions to accelerate the technology assessment, testing and demonstration of a ZEC plant. Brief remarks are provided on complementary projects dealing withCO2separation and gasification costs.

Jan 1, 2004

By E. B. Kroeger, Y. P. Chugh

The goal of this project is to develop, demonstrate, and document the beneficial use applications of a ponded F-fly ash as a road subbase material for the 2.1-mile Meredosia Industry Access Truck Route in Meredosia, Illinois. Approximately 60,000 to 70,000 cubic yards of ponded fly ash are proposed for use on this project without negative environmental impacts to surface water or groundwater. The County Highway Truck Route will consist of a 24-foot wide road built on a 0 to 7-foot thick compacted F-fly ash subbase. Laboratory testing indicates this fly ash will serve adequately as a road subbase, conforming to IDOT standard specifications. The economic considerations of using the Meredosia F-fly ash will also be developed so that a detailed cost-benefit analysis can be prepared for this project and for future projects. This project represents a two-year cooperative development and demonstration effort among the Office of Coal Development and Marketing (OCDM) of the Illinois Department of Commerce and Community Affairs (IDCCA), Southern Illinois University (SIU), Morgan County Highway Department (MCHD), Illinois Department of Transportation (IDOT), AmerenCIPS, and the Morgan County Regional Planning Commission. It is anticipated that monitoring activities will continue for a period of three (3) years after the completion of this project. The MCHD and IDOT will oversee all construction activities and long-term performance evaluation studies. Successful demonstration of large-volume beneficial use applications of F-fly ash at this site will significantly reduce management costs for power plants burning Illinois Coal. Furthermore, it will encourage similar utilization strategies at other sites in the State of Illinois.

Jan 1, 2002

By S. K. Kawatra, S. A. Moffat, K. A. DeLa’O, T. C. Eisele

It was observed that the efficiency of some autogenous grinding circuits was dependent on temperature, with the energy-efficiency of the grinding process decreasing in the winter months, accompanied by an increase in critical-size production. Several possible causes of this phenomenon were suggested, including: • Increased brittleness of the ore during blasting in the pit at low temperatures, leading to increased levels of internal cracking that would lead to rapid breakage to critical size in the mill; •Brittleness changes of the rock in the mill; and • Changes in the durability of the rock caused by either formation of ice on the surface, or freezing of water inside the pores and cracks of the rock. To determine which mechanisms were occurring, drop tests were carried out using frozen and unfrozen rock with varying degrees of porosity, both dry and water-saturated, and which had been blasted for mining in summer and in winter. These tests showed that there was no difference between the summer-blasted ore and the winter-blasted ore, and that durability changes in dry rock over the temperature range from 25ºC to -25ºC were negligible. However, water-saturated rock showed an increased resistance to breakage upon freezing, particularly when the rock was highly porous, or when a layer of ice formed on the surface. Seasonal changes in the durability of rock in grinding are therefore due to formation of ice in and around the rock.

Jan 1, 1995

By S. K. Kawatra, A. K. Bakshi

Mineral suspensions in water show Newtonian flow properties at low percent solids. However, this changes to a non-Newtonian regime as the pet-cent solids increases. For Newtonian fluids, viscosity is independent of shear rate, hut, for non-Newtonian fluids, viscosity varies with shear rate. Therefore, if the slurry is non-Newtonian, attempting to measure the viscosity at a shear rate different from the shear rate experienced by the fluid within the process is futile. This is especially true for a hydrocyclone, where the rate of shear is different at different points within the hydrocyclone. In this case, it is very important to determine the flow type of the suspension before attempting to establish any correlation between the viscosity and the process efficiency. A new technique to distinguish such changes inflow type was developed. This involves two viscometers: a coaxial cylinder-type viscometer that measures apparent viscosity at low shear rates and a vibrating sphere-type viscometer that measures the apparent viscosity at high shear rates. For each of these instruments, special precautions were taken to allow, for the measurement of the viscosity of rapidly settling mineral suspensions. Because the vibrating sphere viscometer is operated at a much higher shear rate than the rotating viscometer, the two instruments together could determine the shear-rate dependency of the viscosity. Ground silica (80% passing 65 µm) in water was used to prepare slurries at concentrations ranging from 10% to 70% (by weight) solids. The viscosity of each slurry sample was measured simultaneously by both viscometers, and the results were compared. With this technique, it was found that all of the silica-slurry samples tested were in the Newtonian flow regime for up to 70% (by weight) solids. Methocel and Cellosize polymer solutions showed clear non-Newtonian behavior using this technique. This confirmed that non-Newtonian behavior of the silica slurries, if present, would have been detected by this arrangement.

Jan 1, 1997

By K. K. Haramy, J. McDonnel

INTRODUCTION Primarily because of mining at greater depth, an increasing number of coal mines in the United States experience floor heave problems. In many instances, the floor heaves at a slow rate without causing health and safety related problems; only additional roadway maintenance and coal handling equipment are required. However, when rapid, massive heaving occurs, the safety of mine personnel in the vicinity is jeopardized. Extensive floor heave causes a redistribution of stress around the mine opening and can cause additional ground control problems. This paper presents an analysis of rapid floor heave in a deep western coal mine. The analysis is based on field measurements, laboratory data, and beam design theory. Factors affecting floor heave, such as mining-induced stress, mine opening size, entry orientation, mine geology, rock physical properties, and gas pressure, are considered. Examination of floor heave in the mine indicates that heaving is primarily caused by deformation of a soft floor member that is subjected to high mining-induced stress. Theoretical analysis of in situ floor stresses resulting from overburden loading indicates that floor failure will occur. The analysis is confirmed by visual observations of floor heave in the mine. Recommendations for mine layout and opening design to control rapid, massive floor heave under these conditions are also presented. MINE-FLOOR-FOUNDATION THEORY The floor stratum in a coal mine acts as a foundation to support coal pillars and artificial supports, thereby providing support to the mine roof. The overburden load, transferred through pillars and other supports, applies tremendous stress to the floor. Soil mechanics theories provide solutions for foundation design problems that apply to the mine floor. Based on foundation theory, vertical load on pillars causes high shear stress zones in the floor. If the floor is relatively weak, it may fail and dislocate upward into the mine opening. Strong roof strata that do not readily fail transmit most of the overburden load through pillars to the floor. Heaving may result, depending on the thickness and physical properties of the floor

Jan 1, 1986

By R. P. Benson, D. H. MacDonald, D. R. McCreath

1 - INTRODUCTION The Canadian Shield is well known as being among the older exposed areas of the earth's surface. Except for local zones, its extent from the Arctic to central North America is characterized by strong and durable crystalline rocks. It is generally regarded as highly competent for tunnelling and underground excavation and, as a result, many openings are excavated in it with minimal temporary support. If hydraulic efficiency is not a factor, tunnels do not usually require continuous concrete linings. A high percentage of the crystalline rocks of the Shield are of metamorphic origin and as such one of the dominant characteristics is their foliation. Zones of sheared or faulted rock are common in the Canadian Shield, particularly in association with foliation. These zones may be created during the late stages of the metamorphic process, leaving shear zones as an integral feature of foliated rock. As foliation is a preferred direction of weakness, deformation and rupture during subsequent tectonism may also create parallel shear zones. These "foliation shear zones", as described by Deere (1973), are an adverse feature of the otherwise durable rocks of the Canadian Shield. The zones may range from faults of major proportions to seams only a fraction of an inch thick. If fault gouge or alteration products exist in the zone the strength of the rock mass may be great1y reduced. As foliation is usually continuous, large unstable wedges of rock may be created if the opening is subparallel to the foliation. The effect on the construction of underground openings in terms of excavations, support and scheduling can be significant.

Jan 1, 1974

By Warren E. Fife

This paper will discuss the application of a continuous miner using a fixed drum milling type cutting head for the underground mining of hard rock and salt ores. Continuous mining machines of the ripper chain cutting head, oscillating milling cutting head and boring arm designs have been used in rock and salt applications with various degrees of success. The large boring arm miners have been successful in potash, trona and salt, but they have not been successful in mining rock materials like iron ore. The main method used in underground mining rock materials is the conventional drilling and blasting the ore from the solid. This is particularly true for the harder, more abrasive copper and iron bearing ores. The softer salt based ores of potash, trona and rock salt can use several underground mining methods depending on seam conditions. Several of these methods use underground coal mining equipment that has been extensively redesigned to adapt it for use in mining noncoal materials. Conventional mining methods employ the use of a universal cutting machine to undercut or topcut the ore body before face drilling and blasting takes place to produce a smooth parting of the ore. The boring arm continuous miner is widely used in underground mining of potash and trona ores. It produces a tunnel with a smooth semicircular contour which results in good rib and roof stability. The ripper chain continuous miner is also widely used in mining the salt based ores of potash, trona and rock salt. They are used more frequently in Europe than in the United States and Canada. Some reasons for using the mechanical mining machines as opposed to the conventional drilling and blasting techniques for mining hard rock ore bodies are the resulting improved rib and roof control, facilitates selective mining of the ore body, and requires less man-

Jan 1, 1974

By Terry Owen

Business development process. Throughout Cyprus Amax's early months in Russia, the company stayed focused on what was needed from a deposit for economic success. Cyprus Amax's reason for success in Russia is that all involved - its Russian partners, the workforce and expatriates - provided a focused effort that served the project as it worked through the tender process and the Russian regulations. The company developed an understanding of the regulatory process by working with solid, ethical partners. Infused into the Kubaka management structure were Russians with the knowledge to facilitate the process and a professional group of expatriates. Developing credibility and a solid rapport with the Russian mining authority was critical to the success of this venture. Identifying and gaining the trust of key Russian individuals was also critical during the early stages. Gaining their trust and building credibility was part of the process. These key Russians were brought to the United States to visit existing Cyprus Amax mines. These efforts proved valuable in building an understanding with the Russians about the kind of company Cyprus Amax is and the kind of efficient operations that it can run. This was a learning process for all parties. Fortunately, the company was dealing with intelligent and educated people.

Jan 1, 1997