Search Documents

By Feng Dingwu, Chen Jin, Sun Zhongyuan, Peng Shiying

The recent development of rare-earth permanent magnets has impacted the field of magnetic separation. The permanent magnets technology led to the advent of various magnetic separators particularly designed for application in mineral processing. In this paper, a new type of rare-earth PHGMS possessing a higher magnetic field strength in the working zone was developed using finite element analysis techniques. The NdFeB permanent magnets used had properties of 38 MGOe stored energy, and magnetic material flux levels exceed 1.2 T, The combination of scientific and engineering design and suitable matrices can offer an effective separation of industrial minerals, such as kaolin, feldspar, etc. Compared with conventional high intensity electromagnetic separators, the equipment can reduce electrical energy over 80% with lower operation and maintenance costs, and less installation space.

Jan 1, 1995

By R. Llerena, P. Dunstan, R. L. Amelunxen

A single four feet diameter cell, treating a Cu/Mo rougher concentrate, has been fully instrumented and linked to a Distributed Control System. This has enabled the writers to further understand the mechanics of operation of the cell, particularly that of the "TRANSITION ZONE". This is the volume between the feed port and the pulp-froth inter- face. The results have shown a need for the re-designing the control loops whereby the Transition Zone volume (or pulp level ) becomes the single most important control parameter to achieve the de- sired recovery. Air consumption, previously thought to have played this role, is now kept at precoalescence level s for maximum efficiency.

Jan 1, 1988

By R. R. Rollins

Field data combined with theoretical derivations were used to design a surface mining operation using explosive casting. Calculated casting results varied from 44% to 65% depending on bench height. The field tests were performed at an Eastern, contour, coal stripping operation. Results from five experimental casting shots, using a shovel and trucks, are summarized and compared to conventional mining methods. The overburden material removed by casting ranged from 35% to 65%, with an average of 50%. Fragmentation was improved, and it was demonstrated that this procedure is economically attractive, with a resultant cost savings of $0.59/m3 or $5.93/t of clean coal.

Jan 1, 1988

By F. H. Mertens

The concentrators of Gecamines are fed by a great variety of ores and produce different types of oxide and sulfide concentrates. It is therefore important to translate the performances of each circuit in terns of dollars in order to reach cost optimization in each mine to product line. A new system has been recently implemented for achieving this objective. Technical data and expenses are collected, allocated and analysed on mainframe applications. On the other hand, optimization and simulations are carried out on microcomputers which are linked with the mainframe files. Various kinds of auditing reports can be produced, including those leading to investments and cash-flow pattern which are

Jan 1, 1991

By Shoung Ouyang, Pinnaduwa H. S. W. Kulatilake

Available literature on the topic is reviewed. Methods are suggested to improve the presently available techniques to perform probabilistic modeling of shear strength parameters for rock discontinuities. The Mohr-Coulomb model and a power law model are used as strength criteria to model shear strength of rock discontinuities. Use of various regression techniques for point estimation of shear strength parameters from direct shear data are discussed. Goodness-of-fit tests for bivariate beta and bivariate normal distributions are developed, and the applicability of them to represent the distribution of shear strength parameters is tested through examples. Both distributions seem to have potential to represent the statistical distribution of strength parameters.

Jan 1, 1986

By P. S. Parobeck, T. F. Tomb, R. S. Ondry

From October 1980 through August 1982, surveys were conducted on 19 longwall mining operations to obtain data relative to respirable dust levels associated with particular longwall operations and occupations, to make recommendations for enhancing dust control, and, where applicable, to evaluate the effectiveness of new technology implemented to control dust. The paper summarizes the data collected during these surveys and, where possible, draws conclusions and discusses actions that can be utilized to reduce exposures to respirable coal mine dust on longwall mining operations.

Jan 1, 1987

By M. J. Meulendyke, J. D. Purdue

Within the mineral processing industry, a range of grinding conditions exists which include semiautogenous grinding (SAG),rod milling, and conventional ball milling. Each of these mill environments presents a unique environment for grinding media, requiring the application of specific physical and chemical properties for optimum grinding media performance. The environments are characterized by varying degrees and combinations of abrasive, corrosive, and impact wear. An extensive test program has been conducted to determine the extent wear rates vary between these different applications. Test results are related to production results, ball size, and mill operating conditions.

Jan 1, 1990

By Jeff W. Butwell

Mill flotation tailings impounded at the Gooseberry Mine site between 1976 and 1984 were determined to be an economic source of gold and silver recoverable by standard heap leach technology in conjunction with feed agglomeration. Metal recovery at 85 percent Au, 75 percent Ag is attained on properly agglomerated (pelletized) tailings which average 85 percent -75 micron. Because the impounded tailings averaged over 18 percent moisture (32 percent moisture maximum at depth) in place behind the storage dam, the mining method, mixing and agglomeration technique, and materials handling practice were major considerations in making this operation a financial success.

Jan 1, 1990

By Wayne R. Charley

High operating costs and environmental restrictions have combined to increase smelting costs for precious metals to a level where many mining companies cannot afford to operate. The need for a hydro-metallurgical process to produce bullion with an efficient, economical and environmentally safe method is well recognized by the industry. This paper describes the research and development program conducted by Behrent Engineering Company in its investigation of the use of an acidic solution of thiourea for the extraction of precious metals from concentrates and high-grade ores. The areas discussed are: process design parameters, health and environmental aspects and economics of the process. The scope of this paper includes the leaching process, the recovery of precious metals from pregnant solutions and the production of dore'. Thiourea leaching offers a complete alternative to smelting and cyanidization for those concentrates and ores amenable to this process.

Jan 1, 1984

By P. M. Solozhenkin

The proposed technology of antimony calcine processing includes ferrochloride leaching of calcine, reducing solutions, hydrolysis of hydrochloride solutions with antimony oxochloride isolation, synthesis of antimony trioxide by SbOCl neutralization and its drying, regeneration of hydrolysis solutions. The optimum parameters of separate stage of process has been determined and the chemical character of process has been given. During the leaching of calcine we succeeded to transfer 92.16- 95.66% antimony to solution. On the worked out sheme we attained recovery of antimony to antimony trioxide near 90 .5% Antimony triozide contains 99.5% Sb2O3. The composition of sinter burdens for pigments preparation "Naples Yellow" different colours from brightly-yellow, yellow and lightly yellow has been proposed. Three-sulfuretted antimony-antimonic cinnabar have been prepared by precipitation of antimony solutions by potassium sulfur-bearing solution. The prepared compounds correspond to inorganic pigments for artistic paint. The amorphous antimony-ferrous black we prepared by aluminium cementation of hydrochloric antimony solutions. The ferrous black were used as artistic paints and for coating of metals by antimony.

Jan 1, 1995

By G. D. Elliot, R. L. Grayson, G. L. Winn

For the years 1990 and 1991, West Virginia's underground coal small-mine fatality rate was approximately 10 times higher than the national coal-industry fatality rate. Although the number of fatalities went down from 22 in 1991 to 17 in 1992, West Virginia still led the nation in coal-mining fatalities. A team of mining and safety professionals from West Virginia, interfacing with the Mine Safety and Health Administration and the West Virginia Office of Miners' Health, Safety and Training, studied this problem. A clear path for formal intervention was determined and is presented here.

Jan 1, 1996

By R. F. Al-Fariss

The phosphoric acid industry is expected to develop in Saudi Arabia in the near future. There are three main reasons for expecting this: the discovery of phosphate deposits in the Sirhan-Turayf region, the construction of phosphate fertilizer facilities of the TSP, DAP and NPK plants on the east coast of the country, and the availability of an ample amount of sulfur As a by-product from the petrochemical industries. This study is a part of the research work performed in the chemical engineering department At King Saud University to evaluate the Saudi phosphate rocks for the wet process phosphoric Acid production and to test different flotation methods for the carbonate rich phosphate rock In a laboratory scale flotation cell. Experimental results for the above tests, as well as Beneficiation by calcination, are presented.

Jan 1, 1993

By Michael J. Martinson, John R. Larsen, J. Warren Andrews

Measurements reported in the paper were recorded in an active Green River, Wyoming, trona mine, partly as a teaching exercise and partly to provide the mine in question with additional input data for its ventilation network program. Measurements were made: - in representative three-entry intake airways in room and pillar sub-mains; - between the lower portion of a vertical down-cast hoisting shaft and the start of an intake airway system established in a room and pillar main; - in a representative downcast section of a divided vertical shaft, and of the collar entrance loss at the top of the same compartment. Pressure differences were measured with manometers and trailing hoses, air flowrates with calibrated anemometers, and barometric pressures and wet-and dry-bulb temperatures were recorded for density determinations. Where possible, results are quoted as Atkinson friction factors, and relevant measurements are recorded in some detail to show the magnitude of fluctuations in observed pressure differences.

Jan 1, 1987

By Jin Anshi, Wang Dai, Wang Zingshen

Both fire and gas problems in Fully Mechanized Sublevel Caving Coat Face are quite different from those in common fully mechanized coal face. Pouring N2into the goaf would be the best method to prevent fire in the goaf. In this paper how to determine parameters of pouring N2 is discussed. Comparing distributions of gases and temperature before pouring N2into the goaf with those after pouring N2 into the goaf, the effectivenesses of preventing the fire by pouring N2 into the goaf are testified. Some special gas problems appear in Fully Mechanized Sublevel Caving Coal Face, which are proved to be serious and interrelated with pouring N2 into goaf. Finally, a few methods adopted to deal with gas problems are described simply.

Jan 1, 1991

By C. Timothy Shaw, Michael Karmis, Hans de Ruiter

The Society of Mining Professors/Societät der Bergbaukunde was established during a meeting hosted by the Montanuniversität, Leoben, Austria, in 1990. Since then, the Society has primarily functioned as a European entity of senior academics in the mining engineering discipline. The Society is considered the natural successor of the historic Societät der Bergbaukunde, formed in the early 18th century and recognized as the world’s first international scientific society. At the 14th Annual General Meeting of the Society, in Milos, Greece, 2003, a decision was made to examine the role of the Society in global minerals education, to reassess its vision and membership guidelines and to develop the future direction of the organization. A special Planning Subcommittee developed a plan of action to allow the Society to transform and position itself as the premier global voice of the academic minerals disciplines and to lead the effort of restructuring minerals education. The new vision calls for reconstituting the Society as a vibrant global society, representing the majority of minerals academics and making a significant contribution to the future of the minerals disciplines. This paper will present the history, vision, goals and action plans of the Society to help ensure that the necessary scientific, technical, academic and professional skills are available for the sustainable supply of minerals to mankind.

Jan 1, 2005

By Simona Markic

With the aim of environment protection the program package HOMOGEN is used for realizing the planning and noxious components control in the coal produced. Using the program package PRIPREMA the division in levels and transformation (Hermite polynoms) in the N (0,1) distribution are made. By separated kriging 50 m x 50 m blocks are estimated on the levels and detailed distributions of the estimated component content are obtained. The face - longwall face is built in the blocks estimated in this way, and the direction of mining is determined. Using the stochastic simulation the distribution of the estimated production component (e.g. sulfur) on the face is obtained. Simulating the production of all faces in operation the distribution of the estimated daily mine production component is obtained. The estimated depot component is obtained in the same way. This procedure is used in the short-term planning of the estimated component movement for a given period in advance, and also in the daily production control in the case of changing conditions, e.g. the increased atmospheric pressure. The technology is successfully applied to the Velenje Lignite Mine Slovenia.

Jan 1, 1992

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations. Key words: Mineral liberation, Flotation, Image analyzers

Jan 1, 2003

By Richard R. Klimpel

The author was the banquet speaker at the 48th Annual MPD meeting, sponsored by the SME Colorado Minerals Processing Section, May 14-16, 1998, in Colorado Springs, CO. Here are his remarks. It has been an exciting experience to have spent 34 years involved with the process of generating patented technology eventually leading to commercialization. In today's terminology, this process is called technology transfer. I have had the unusual experience of being involved doing basic research as an inventor while also being responsible for managing new product development and commercialization. In addition, I worked for 31 years before my retirement for a large research-oriented company, The Dow Chemical Co. In 1995, the company spent more than $1 billion dollars on research and development. The last three years of my career have been spent working with a research-oriented university, The University of Florida. And I have worked as a consultant helping several companies to optimize their products and processes. It is on this cumulative experience base that the preparation of this article is based.

Jan 1, 1998

By Stanley M. Miller

Analysis of discontinuous rock masses for engineering design purposes requires information about fracture characteristics. For such studies, fractures or other elements of the rock fabric (bedding, foliation, etc.) should be considered in a statistical manner because they generally have high frequencies of occurrence and are discontinuous over the design area. A practical design procedure includes defining structural domains as those areas which contain fractures with similar orientation patterns. Within a structural domain, the statistical distributions of fracture set characteristics (spacing, fracture density, dip, dip direction, etc.) may be computed from mapped data and then used to quantitatively describe the rock fabric. These distributions can then be randomly sampled (using Monte Carlo techniques) to simulate the rock fabric and to help define potential failure surfaces along fractures. 1 The prediction of failure geometries is an essential part of stability analyses used in designing rock slopes or underground openings. In current probabilistic design procedures, Monte Carlo techniques that rely upon the iterative generation and analysis of deterministic instability models do not incorporate spatial aspects of the random variation in fracture set characteristics, 1,2 but consider the characteristics to be spatially independent.

Jan 1, 1979

By P. Coleman, J. C. Kerkering, S. Iverson

A fatal accident may result when a dozer is driven over a hidden void in a coal surge pile and the dozer falls into the void, burying and suffocating the dozer operator. This type of accident was analyzed by researchers from the Spokane Research Laboratory of the National Institute for Occupational Safely and Health using inexpensive fault-tree programs that had been developed, for use on a personal computer. Fault-tree analysis is a systematic safety-analysis tool that proceeds deductively from the occurrence of an accident event to the identification of the root causes of that event. The analysis identified basic and intermediate events that led to the burial of the dozer and graphically depicted the interrelationship between the basic events as well as the intermediate events leading up to the accident. A sensitivity analysis on assigned probabilities showed which events had the greatest influence on dozer burial in a coal surge pile. Operational guidelines and engineering controls are suggested to decrease the probability of a burial event.

Jan 1, 2002