Search Documents

By Cheng Ang, Yun Bai, Zhi Liu

"This paper presents a conceptual design of an innovative tunnelling method named the Ring Pipe Jacking Method (RPJ) which is conducted by the Ring Pipe Jacking Machine (RPJM). The RPJM consists of a double ring shell which forms a ring section where small interlaced cutter heads or several micro tunnelling machines are assembled to cut soil. Similar to the conventional pipe jacking method, the RPJM also needs a thrust system, a slurry transport system, and a control system. To satisfy the need for large/super large or special section tunnels in future, the RPJM is designed to reduce sharply the excavation face to the annular section, thus enhancing the face stability. Part of the innovation is that the RPJM uses modular cutter heads or micro-TBMs which can be reused. The typical double shield shape can be easily changed by reinstalling the modular cutter heads. Modularity allows the tunnel to be cut in any cross-section shapes, ranging from a circular tunnel to a rectangular one. INTRODUCTION The demand and requirement to utilize urban underground space is rising with the rapid social development in recent years. It is necessary to reduce excavations of the urban ground surface to ensure smooth traffic in cities. Therefore the conventional open cut construction method for underground tunnels can no longer satisfy the need of practical engineering, and it is taken over by trenchless technologies .The Pipe jacking method is an important trenchless technology and is used more and more frequently to install underground pipelines, but the present pipe jacking method still has many problems. For example, it is not suitable for installing large-diameter tunnels and it also has difficulty in construction of short radius curved tunnels. This paper presents a conceptual design of an innovative pipe jacking machine named the Ring Pipe Jacking machine (RPJM) and introduces the correspondent Ring Pipe Jacking Method (RPJ) which can be applied to construct large-diameter tunnels. Furthermore, technical characteristics and superiority of the ring pipe jacking method are analyzed in this paper."

Jan 1, 2016

By T. A. Toney

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers, and recirculation have been attempted with some success. This paper reports on a novel (Patent Applied For) approach to retreating spiral middlings m a heavy-media-cyclone circuit.

Jan 1, 1998

By Paul Grisley

Air-supported belt conveyors-conveying systems that replace troughing idlers with a film of air-were a revolutionary concept when introduced in the 1970s. But high installation and operating costs limited their application. Now, system refinements have led to successful applications, even under the challenging conditions of mines and process plants. In this presentation the author will discuss the latest developments in the engineering of these systems, including the ability to retrofit existing transfer points with modular air conveyor components. Air conveyor applications and limitations in mineral-handling operations will also be examined.

Jan 1, 2002

By C. Leal

Modern production has as goal to reach high and uniform quality in their products. To success with this, it is essential to have a good knowledge of the different variables involved in the process. Investigation or analysis of a process or system has as references the measurements of the variables. These measurements are presented normally in form of data. These data are measured in intervals over time. The aim with measurement of the data in a process is to obtain information about the state of it in order to have it under control. Other goal is to know how the results are affected by the process variables to improve upon product quality, redunding manufacturing cost, better pollution control etc.

Jan 1, 1994

By Laurent Rus, Bakar Amara, Jean Habimana

The La Fontaine Tunnel in Montreal, Quebec is currently undergoing major structural rehabilitation work and systems upgrade work to comply with current codes, standards and best practices in fire life safety and to extend its lifespan of this 55-year-old immersed tube tunnel for at least another 40 years. The paper discusses design consideration of ongoing works that include structural analyses to evaluate repair strategies for the post-tensioned reinforced caissons, the scheme to repair two leaky joints between caissons, the design of passive fire protection that involved in situ and real scale laboratory tests, and other tunnel systems upgrades.

Jun 13, 2023

By John T. Langstaff

Rock bursts in the deep metal mines of the Coeur d’Alene district present an ever increasing problem in the safe and economic mining of the district’s silver, lead and zinc ores. Hecla Mining Company operates two mines in the district - the Star, a 1100-ton/day lead-zinc mine, and the Lucky Friday, a 750-ton/day silver- lead mine. Rock burst problems at both operations prompted Hecla management to make an all-out attempt to find a practical method of predicting and eventually controlling these bursts. Research by personnel from the Denver Research Center of the Bureau of Mines at ASARCO's Galena Mine indicated that a recognizable pattern of seismic activity preceded some bursts and this activity could be precisely monitored by present- day, off-the-shelf electronic devices. Using information gained by the Bureau and other sources, Hecla designed and installed a 24,- channel seismic monitoring system in the Lucky Friday mine. Installation was completed in December 1973 and after a year of successful operation, it was decided that a similar system would be installed in the Star mine. This second installation was completed in June 1975. Both systems are now operating and providing continuous information on underground seismic activity. Each monitoring system consists of a network of geophones with attendant amplifiers that are connected by shielded cable through an interfacing device to a computer. The origin of each seismic event is determined by the computer and a three-dimensional location is printed out. This information is plotted daily and is used to pinpoint rock burst prone areas and chart their relative seismic activity. This paper will review the causes and effects of rock bursts in the Coeur d'Alene district, the equipment and operation of the microseismic system at the Star and Lucky Friday mines, and the results obtained to date.

Jan 1, 1977

By H. V. Scotland III

Lafarge Corporation's Texas Quarry, in Baltimore MD, achieved a substantial expansion of pit reserves by removing an inactive underground mine. The day lighting program, designed, and completed in 1997, open pit mined more than 400 meters of room and pillar workings which were originally developed to recover high brightness Calcium Carbonate. The project proved to be a challenge throughout its course as the pit plan was modified and successful daylighting techniques were developed to remove the mine without adversely affecting the safety of the operation, quality of the stone recovered, or negatively impacting the surrounding community. The design parameters and techniques developed and implemented at Texas may prove of interest to other operators as they are faced with daylighting opportunities. This article will detail the challenges we faced and the solutions which made the project a success.

Jan 1, 1999

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019

By M. Li, J. K. Thompson, A. S. Azman

"Powerful mining systems typically generate high-level noise that can damage the hearing ability of miners. Engineering noise controls are the most desirable and effective control for overexposure to noise. However, the effects of these noise controls on the actual hearing status of workers are not easily measured. A tool that can provide guidance in assigning workers to jobs based on the noise levels to which they will be exposed is highly desirable. Therefore, the Office of Mine Safety and Health Research (OMSHR) of the National Institute for Occupational Safety and Health (NIOSH) developed a useful tool to estimate the hearing loss due to occupational noise exposure in a systematic way and evaluate the effectiveness of developed engineering controls. This computer program is based on the ISO 1999 standard and can be used to estimate the loss of hearing ability caused by occupational noise exposures. In this paper, the functionalities of this software are discussed and several case studies related to mining machinery are presented to demonstrate the functionalities of this software. INTRODUCTIONPeople regularly exposed to noise can develop hearing loss at different levels of severity depending on a number of factors. The resultant hearing loss can affect one’s ability to understand speech, learning, acoustic signal perception, or appreciation of music. Hearing loss caused by overexposure to noise has long been recognized in literature. However, it still does not get serious attention by those working in noisy environments because the loss of hearing ability is a gradual process and workers are often unaware until the damage becomes an apparent problem. In the United States, occupational hearing loss is one of the most common work-related illnesses. Depending on the definition of exposure and impairment, in 2012 the National Institute for Occupational Safety and Health (NIOSH) estimated that there are between 5 and 30 million workers in the U.S. who are exposed to noise levels at work that put them at risk of hearing loss.4 In the mining industry, noise-induced hearing loss (NIHL) is particularly severe due to the fact that heavy-duty machinery is widely used to improve production efficiency, and this machinery can generate much higher-level noise than the permissible level defined by regulation. As a result, the mining sector has the highest prevalence of hazardous workplace with high noise exposures (76%) among all industrial sectors."

Jan 1, 2015

By Todd Kilduff, Ryan O’Connell

Pipe canopies continue to gain momentum as a reliable methodology for construction of excavations below critical facilities with minimal surface settlement tolerances, such as railroads or roadways. Two tunnel projects designed by Kilduff Underground Engineering in the Salt Lake City, UT area, each at varying stages of completion, had project design criteria for selection of a tunneling methodology to minimize surface settlement. Both projects consist of a pedestrian tunnel, one crossing beneath a major roadway in downtown Salt Lake City and the second beneath UPRR tracks. Both projects were in difficult, coarse alluvium/fan ground conditions with project criteria that resulted in minimal cover above the tunnel. For each project, a pre-support pipe canopy was designed, requiring the placement of steel, canopy pipes driven the extent of the tunnel length. The pipe canopy is installed using a trenchless technology and then excavated with SEM tunneling and shoring provided by traditional support of excavation methods. The pipe canopy pre-support method offers a low-impact method to install an underpass beneath critical structures by adding significant stiffness to the subgrade to mitigate surface settlement during the main tunnel excavation sequence. These case studies seek to communicate the challenges associated with pipe canopy installation in site-specific ground conditions and explains how these challenges were overcome. This paper aims to define the project risks and describes the pipe canopy methodology as a viable solution to mitigate surface settlement in low cover tunneling scenarios.

Jun 13, 2023

By Frank W. Reinrniller

Mill ball charging systems have undergone little change during the past two decades. Most operations utilize a locomotive/ball car combination to load and haul charges from the ball storage bin to the mill charging boxes or, alternatively, transport charges to the charging boxes by means of a ball bucket handled by bridge crane. This paper describes a new concept in ball handling systems that is in operation at the Island Copper Concentrator of Utah Mines, Ltd. at Port Hardy, B.C. This system employs a narrow belt conveyor to convey a weighed charge to each of nine belt unloading stations at the mills. In operation, the system has proved to be practicable, trouble-free and economical of operating labor.

Jan 1, 1977

By Wade W. Bristol

The Jerritt Canyon Joint Venture project is located about 80 km (50 miles) north of Elko, NV. It produces approximately 9.3 t/a (300,000 oz/year) of gold. The joint venture is 70% owned by Independence Mining and 30% by Meridian Gold. Independence Mining is the operator. The Jerritt Canyon Joint Venture started operations in 1980 by mining a series of open-pit mines. The discovery of deeper ores during early 1990s made it neccessary for the operation to mine a large portion of its annual production by underground mining methods. Underground production started in 1993 at the West Generator Mine. This was followed by the Murray Mine in late 1994. Two additional underground projects are being developed. Underground mining at Jerritt Canyon is scheduled to produce about 3.9 t (128,000 oz) in 1997.

Jan 1, 1997

By S. A. Moffatt

For several years iron ore processing plants, located in the northern U.S. experienced seasonal decreases in the grinding efficiency of their primary autogenous mills. Kawatra and Eisele (1992) studied this phenomenon in an operating plant and characterized it in terms of specific energy consumption (Fig. 1) and production of critical size material (Fig. 2). Critical size material is defined as ore that is too small to be effective grinding media and too large to be ground. This data showed that both specific energy consumption and critical size production increased during the winter months. The increased energy consumption was in part a result of an increase in the viscosity of the mill pulp at colder pulp temperatures. However, viscosity could not fully explain the changes in critical size production. These changes are most likely due to changes in the breakage characteristics of the ore. Other studies were also conducted to determine if thermal and physical properties of iron ore changed at colder temperatures. These are summarized below:

Jan 1, 1993

By P. Knudsen, S. Rosenthal

INTRODUCTION In 2010, Montana Tech was gifted 65 acres of land immediately west of the campus. The parcel of land included an old silver mine called the Orphan Boy Mine. The Orphan Boy and its sister, Orphan Girl, were developed about1895 and operated until 1956. In addition to the gift of land, a significant industry gift was obtained to develop a first class training facility, which we call the Underground Mine Education Center (UMEC). The UMEC has been funded primarily by industry through donations of dollars, equipment, and supplies. The UMEC is a unique hands-on, educational environment for today’s students who are being trained to find, develop and process the worlds' natural resources. The center complements courses in mining engineering, geological engineering, environmental engineering, metallurgical engineering and occupational safety and health. It also serves as a as research facility utilized by students and faculty, and other organizations interested in doing research a hard rock underground mine. LOCATION The Orphan Boy and Orphan Girl Mine are located approximately 700 feet (ft.) apart and the Orphan Girl Mine is part of the World Museum of Mining. Underground they are connected on various levels and all levels below the 100 ft. level are currently flooded. The Orphan Boy mine was 804 ft. deep and Orphan Girl was 3200 ft. deep. The surface locations of the two mines and some of the underground workings on the 100 ft. level are shown on Figure 1 (2015). CONSTRUCTION Land ownership was gifted from BP/ARCO in 2010 and planning started immediately. In June of 2011, site development for the decline to the 100 ft. Level of the Orphan Boy began with a satisfactory portal site developed (Figure 2). We hoped to be able to start driving the decline in July. However, the portal was sited approximately 125 ft. away from a natural gas line that bisected the Montana Tech campus. While outside the right of way for the line, Northwestern Energy requested that no blasting be performed near the gas line until such time as the gas line was abandoned in the fall so decline development was put on hold. The gas line was officially abandoned in January of 2012.

Jan 1, 2019

By R. Balderrama Neder

A study consist in 20 column leach tests was performed for the "EI Arco" Copper ore deposit, located on Baja California, Mexico. The main purpose was to define the basic criteria like recovery and sulfuric acid consumption, for a commercial heap leach system design, to process the oxide Copper (Chrysocola) of the deposit. Leach parameters such as, amount of sulfuric acid in the cure solution, cure technique, particle size of the material, leach solution's flowrate application, leach solution's acid strength and height of the lifts, were evaluated to choose those parameters in which the results were the best ones for that particular design.

Jan 1, 1997

By W. L. Hollinshead

For more effective and cost saving production in tunnels, the machinery used on construction sites will be equipped with guidance systems combined with working procedure management systems. This paper describes sensors for these systems and various system configurations. A project is described which uses a computerized guidance system on an underground mining machine for guidance and profile control.

Jan 1, 1999

By Lianhui Jia, Yali Han

"The key technologies of a large rectangular pipe jacking machine with dimensions of 10.12m × 7.27m (width x height) include selection of rectangular cross-section cutting modes, analysis on the strength and stiffness of the rectangular shield, integrated control of electro-hydraulic proportional thrust systems and ground conditioning for excavation are presented in detail in this paper. These key technologies have been successfully applied and verified on site during tunneling, providing a new concept for the building of large rectangular traffic and pedestrian tunnels in urban areas for the future.1 INTRODUCTIONIn the past, underground tunnels were mainly used for drainage, sewage, utilities, metro tunnel, etc. and most of them had circular cross-sections. Recently, as a result of economic development, gradually accelerating urbanization process and diminishing ground space, underground tunnels have already become a new trend for urban underground space utilization. Due to the heavy traffic flow, the demands for rectangular cross-section underground tunnels, such as pedestrian underpass and road tunnel, are increasing gradually.The Rectangular pipe jacking machine (hereinafter referred to as RPJM) was firstly developed in Japan for the construction of metro station, pedestrian underpass, underwater tunnel by-passes, etc. Kazunaki Kawai et al. introduced a RPJM developed and manufactured by KOMATSU in 2002 [1]. Tosikazu Kubota et al. confirmed the rectangular tunnels’ superiority to circular tunnels with regard to larger inner cross-section and lower construction cost in their RPJM construction reports [2]. Compared to circular pipe jacking machines, a RPJM also has the merits of a higher inner tunnel space utilization ratio and is able to excavate in shallow overburden areas. As shown in Figure 1, the effective area of a rectangular tunnel is more than 20% higher than that of an equivalent circular tunnel."

Jan 1, 2016

By L. Adler

To properly analyze and apply mining equipment, a systematic, current, inclusive, and simple classification scheme is required. This paper provides such a classification for Roadheaders. This Roadheader classification is based on factors, such as the rock cutterhead, the boom type, and the chassis configuration. It first assigns Roadheaders as an equipment type within the larger group of Integrated Excavators. The Roadheader type is then delineated into the following subtypes: the standard, the extended boom, the tunnelers, and the miscellaneous. Next, these subtypes are devolved into kinds, and finally variants and attachments are considered. To resolve inconsistencies in characterizing the Roadheader, cross-referencing is employed within the classification scheme.

Jan 1, 1996

By R. L. Lewis

The White Pine Mine is the second largest active underground copper mine in the United States, covering an area of approximately 34 km2 in the Upper Peninsula of Michigan. A numerical flow model of the White Pine Mine was constructed to evaluate engineering controls that would reduce the rate of mine water discharge after closure. Of the passive controls evaluated, the placement of low-flow bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35 percent.

Jan 1, 1996

By Kim McKnight

Dupont has successfully incorporated a Floatex Density Separator into its wet-gravity operations for the recovery of zircon from titanium tailings. Results indicate that the Floatex achieved a zircon recovery of approximately 95% while rejecting similar amounts of quartz and other gangue minerals. Additionally, a unit capacity approaching 16 tonnes/hr/m2 was achieved. Results also show that the alumino-silicates can be separated into other product streams that will further improve process economics and minimize waste material. The improved plant feed grade provided by the Floatex has allowed for either an increase in overall plant capacity and/or final product grade. This paper will present the findings from the in-plant study.

Jan 1, 1996