Search Documents

By Y. Zeng

Experiments were performed under batchwise wet grinding conditions with dolomite mineral. The vibration signal was received by an accelerometer and transmitted to a mini-processor. The signal was first stored on a digital tape recorder (OAT) in voltage format during the grinding tests. The original signal was then re-sampled and converted into data format for IBM or compatible personal computer by a digital oscilloscope. The root-mean-square (RMS) and power spectrum was estimated on the time-domain vibration signal. A partial correlation analysis was applied to the frequency-domain signal to detect the non-zero correlation between the frequency bands and the operating parameters. A multiple stepwise regression was used to locate the key frequency bands for describing a particular operating parameter. After vibration analysis, the operating parameters in grinding, for example, the mill speed, the powder filling, the pulp density, the pulp temperature and the particle size were found to be strongly correlated with a few frequency bands. The grinding process could therefore be monitored using the vibration signal.

Jan 1, 1992

By Silvia Misk, Cristina Araújo, João Felipe Costa, Roberto Rolo

Linear estimation methods are widely used for resource evaluation. Among the existing linear estimation methods, ordinary Kriging (OK) was accepted as the best estimator to determine the average ore grade of each block. However, OK is inadequate for modeling small blocks in relation to data spacing, resulting in over-smoothed models. In this study, the results of the recoverable resource from the short-term model are compared to estimated models generated by the traditional method, i.e., OK, and non-linear methods. The conclusion is that non-linear methods improve the accuracy and precision of the long-term model when compared to the model generated by OK.

Jun 25, 2023

By J. Urosek

Since the promulgation of the Mine Safety and Heath Administration?s (MSHA?s) Final Rule on mine seals (30 CFR § 75.335(b)), which became effective on October 20, 2008, many seal designs have been approved by MSHA and constructed by the mining industry. Since the effective date of the Final Rule, several issues on the design, construction, and/or inspection of seals have been brought to the attention of MSHA. Several such issues discussed in this paper include; the directional, design-load criteria required by MSHA for 50-psi seals, 120-psi seals, and greater-than-120-psi seals; the presence of fireclay in the surrounding strata where a mine seal is to be built; the measurement of convergence of the mine opening in which a seal has been constructed; where gob-isolation seals can be used; and the importance of periodic inspection of seals.

Jan 1, 2010

By G. Labonte

The behavior of four different redox sensing electrodes (gold spiral, black platinum, chalcopyrite, and galena) during roughing and cleaning flotation is examined and related to the flotation response. Although it is difficult to provide unequivocal interpretations of the different potentials measured, the results indicate that the solution potential (as sensed by the black platinum electrode) is different from that of the pulp potential (gold spiral) and is only weakly related to the flotation response. On the other hand, the potentials exhibited by the gold spiral and the two mineral electrodes are related to the floatation response. The gold and mineral electrodes exhibit different transcient responses during the addition of flotation modifiers (e.g. NaCN, SO2). These responses appear to be related to the reactivity of the minerals and could indicate the conditioning time required to achieve flotation or depression of selected minerals.

Jan 1, 1989

By P. K. Davis

The results of a previous basic study of the flow and design characteristics of the hydrocyclone has shown that a recovery as high as 99% with a product rating of 0.95 can be achieved on a "batch?2 basis with a single, water-only cyclone if it is configured properly. The next logical step was to demonstrate continuous processing of gob for the efficient recovery of coal by means of a laboratory-size demonstration system. A project to design and construct such a single-cyclone system was also sponsored by the U.S. Department of Energy. A recovery of 93% with a product rating of 0.89 was demonstrated. The system design and the data taken are discussed.

Jan 1, 1989

By N. A. Abdel-Khalek

Laboratory flotation tests were carried out on six Polish samples of different rank. Each coal sample was screened into 7 size fractions. The floatability of size -by- size for various size ranges for different samples was investigated as: well as the original samples. The results showed that in flotation of size -by -size, the intermediate size had the maximum floatability. The range of this intermediate sizes varied with the rank of the coal. Entrainment was shown to be an important mechanism to the recovery of fine particles in flotation of the original samples".

Jan 1, 1989

By V. Karra

Based on extensive investigations on the effect of design variables on process performance, during 1982-85, Nordberg developed a 1000 hp cone crusher, with the objective of boosting crushing productivity in existing plants. The 2390 fits on the same foundation as the 7' SHD Symons cone, but is designed to give two times the capacity of the 7'. The economies of scale involved give the customer substantial cost savings. In this paper process performance of the Nordberg 2390 relative to the 7' SHD Symons cone, while crushing the same ore, will be presented. Also, implications of such a crusher scale-up to associated cost savings will be addressed.

Jan 1, 1988

By J. H. Mackey

"Where can I obtain a reclamation bond today?" "Who is writing your bonds?" These questions are common and heard frequently. The fact that the Society of Mining Engineers has determined that two of the five environmental topics reviewed at the 1989 Annual Meeting relate to reclamation bonding indicates to me that those who are involved in the coal industry, no matter what capacity, remain very cognizant of the reclamation bonding dilemma.

Jan 1, 1989

By M. Fig, J. Brune, C. Strebinger, G. Bogin, J. Grubb

"Although it is known that explosive gas zones can form and sustain combustion in a longwall coal mine gob, a complete account of the interaction of the methane flame and gob remains obscure. The goal of this study is to examine the impact of several gob parameters such as packing orientation and void spacing. The impact of ignition location is also detailed. A series of experiments with methane flames were performed in a horizontal cylindrical quartz reactor. The reactor was tested both empty and packed with an obstacle wall consisting of spherical glass beads to investigate the impact of various gob parameters. Results demonstrate that methane burning velocity is sensitive to all parameters investigated, and most sensitive to packing density and ignition location. INTRODUCTION The explosion at the Upper Big Branch Mine in 2010 and several other underground longwall coal mine fires and explosions show that explosive gases can mix with fresh ventilation air creating explosive gas zones (EGZs). Investigative reports of these fires have found that EGZs are able to move from the gob and into the active longwall face, endangering workers and equipment [1]. Currently, researchers at the Colorado School of Mines are using computation fluid dynamics (CFD) modeling to predict the location and movement of EGZs in the gob and along the longwall face [2,3]. It is the goal of this work to validate combustion models [4] that include interactions of the flame and the gob for future incorporation into ongoing CFD modeling of EGZs [2,3]. Throughout the years, there has been significant research investigating how flames interact with obstacles and propagate through porous media [4,5,7-11]. Since there is limited access to the gob in a longwall coal mine (Figure 1), the orientation and size of rocks and void spaces within the gob is unknown. Experiments of a simulated gob have been performed in a large scale flame tube in order to investigate the effect of scale (Figure 2) [4,5]. However, the variation in rock spacing, rock orientation, and void location makes it difficult to determine the impact of each of these parameters on methane flame dynamics. This study aims at gaining a stronger fundamental understanding of gob parameters such as spacing, orientation, and ignition location on methane flame propagation. The results from this study will provide a basis for experimentation in larger explosion vessels and will be used to validate methane combustion models for incorporation into longwall ventilation models of EGZ movement [2,3,4]. BACKGROUND Researchers have been studying flame propagation across obstacles and porous media for many years using various fuels and experimental setups [4,5,7-11]. Experiments have been performed in horizontal chambers with both ends open [7], horizontal chambers that are semi-open [4,11], horizontal chambers with both ends closed [8], and vertical arrangements [9,10]. Due to the variation in experimental setups and methods of characterizing flame dynamics such as flame speed, peak overpressure, or burning velocity it becomes difficult to directly compare results. Flame speed is a property of the mixture and refers to the speed of the unstretched flame front normal to the direction of propagation. This study characterizes the flame by its burning velocity, which is the difference between the flame speed and the speed of the unburned gases just ahead of the flame front. However, some references use the terms flame speed and burning velocity interchangeably. In this study, a semi-open quartz cylindrical reactor was used to determine methane burning velocity, which was used as a basis for comparison to determine the impact of obstacle configuration on methane flame dynamics. The quartz reactor also has the unique ability to allow for flame visualization. These features allow for faster combustion model validation [4]."

Jan 1, 2017

By E. De Souza

Rockbursts and rockfalls cause very large safety and productivity losses in underground mines. One of the major unsolved problems of safe, economical rock support in underground mining has been that of maintaining anchorage during dynamic rock loading conditions or seismic related occurrences. It is recognized that the large displacements and high strain rates in excavation walls and underground structures cannot be countered by increasing the strength of stiff rock-reinforcing systems but must be accommodated by introducing yieldability into the support elements. This paper introduces a low cost yieldable support system which provides viable solutions to dynamic support loading. Such system should not only provide a feasible and more effective rock mass stabilization strategy but improve mine safety and reduce losses.

Jan 1, 1998

By L. P. James

The Bulagidun copper-gold system occurs in Tertiary andesitic volcanic rocks. It is located (figure 1, from Curless, 1991) ca. two days walk from the coast in an isolated area on the northerly slope of the main range of mountains, in steep terrain dissected by erosion. Detailed and district-scale exploration from 1988 to 1991 by BHP Minerals defined a small, sub-economic resource of gold and copper. One preliminary estimate of the resource in bedrock suggests 14.4 million tons at 0.68 grams / Tonne Au and 0.61% Cu, in multiple small bodies.

Jan 1, 1993

By B. R. Addison

In the Spring of 1991, Georgia Marble Company of Arizona (GMCOA), acquired the Andrada Marble Company located near Vail, Arizona, approximately 32 km southeast of Tucson. The Georgia Marble Company operation consists of an open pit quarry and a recently constructed, state of the art calcium carbonate milling and processing facility. The open pit quarry exposes white, crystalline, CaCO3, Escabrosa limestone that meets our customer criteria for Consumer and Industrial Filler applications. The Georgia Marble Company Arizona Division facility is designed and engineered to produce a wide range of milled calcium carbonate that includes finely ground and coarse screened products.

Jan 1, 1994

By R. L. Keaton

Since the earliest days of mining, the job of digging coal out of the earth has been considered one of the world?s most dangerous occupations. From 1880 to 1910, mine explosions and other accidents claimed thousands of victims. In 1907 alone, over three thousand deaths occurred in U.S. coal mines. Public concern has prompted the passage of much needed safety legislation; from the creation of the U.S. Bureau of Mines in 1910, to the comprehensive laws of the Federal Mine Safety and Health Act of 1977. This type of legislation, along with the cooperation of industry, labor, and MSHA has contributed greatly in making mining safer and more healthful. Mining deaths and injuries have declined Significantly since those early days. However, even though this trend is positive, none of US can afford to look at the injury numbers and frequency rates and label them as acceptable.

Jan 1, 1988

By E. L. Schrader

Statistical Process Control (SPC) is a cooperative arrangement between a component or raw materials supplier and a manufacturing customer. The supplier must analyze his own manufacturing process and determine, predict, and control those variable elements in the circuit which affect finished product characteristics according to the customer's specifications. The results include: control of fluctuations in product characteristics to a narrow range, close communication between supplier and customer, and an increased responsibility for quality control placed on the supplier. In the mining and. processing of airfloated kaolin some unique problems arise with the SPC concept: 1) The SPC system was designed for manufacturing facilities that did not have to deal with natural variations in their raw material; 2) The airfloat process is relatively simple and offers limited opportunity to change processing steps or "fine tune" a circuit for special product needs; 3) Determining adequate sampling frequency for a plant which processes hundreds to thousands of tons per day is statistically difficult; and, 4) Due to the variety of customer industries served, different SPC programs must be set up to deal with widely varying specifications. For airfloated kaolin, SPC is "in line" process control, not after the fact "quality" control. The emphasis must be on statistically valid sampling of the kaolin ore and complete monitoring of its path through the beneficiation circuit.

Jan 1, 1987

By J. J. Fallon

Las Vegas is a place of many distractions. It is difficult for one to apply himself to sophisticated technical matters in the midst of gambling, liquor, scantily clad young ladies and the top entertainment available in the United States. But, I know that the men and women of SME are made of stronger stuff and will not be tempted by these things.

Jan 1, 1989

By Richard J. Ebens

The trace element geochemistry of the cherty, clay-rich carbonate residuum. Covering much of southern Missouri and adjacent parts of Arkansas was investigated during the early 1970's as part of a statewide geochemical survey of Missouri-1/2/3 The study was environmentally oriented and focused on the character of the "natural' geochemical environment of the state. A great deal of effort was made to collect samples that would represent the geochemical variability of the near-surface environment in an unbiased way. In general, this was accomplished by use of randomization procedures in both collection and analysis. Most of the sampling sites were selected randomly to prevent personal bias from entering into sample selection. In the laboratory, samples were analyzed in a randomized sequence to circumvent the effects of any systematic bias that may have entered into the laboratory procedures. Several residuum samples contained 1 000 parts per million (ppm) or more of Pb, Zn and Ba. All these samples were collected in Washington County in or near the barite district. The frequency distributions shown in figure 1 indicate just how unusual the residuum in Washington County is with regard to these three metals and copper. The shaded parts of the histograms represent the samples from Washington County. The histograms are based on analyses of 141 samples from 38 localities scattered over the subcrop of the Cambrian and Ordovician Formations of southern Missouri and northern Arkansas. Eight localities were selected randomly from over each of four bedrock units--Bonneterre Dolomite, Potosi and Eminence Dolomites, Roubidoux Formation, and the Jefferson City, Powell and Cotter Dolomites. Six localities were selected randomly from over the Gasconade Dolomite. The geochemical "background" for these elements in residuum is defined by samples from outside of Washington County (unshaded part of the histogram); lognormal distribution curves have been fitted to the corresponding parts of each histogram. Clearly, these lognormal models (curves) describe well the background

Jan 1, 1977

By Ian Sheppard, Kugan Kuganathan

The Mount Isa Rocky Paste Fill (RPF) was one of the five fill options investigated for the Enterprise Mine filling between June 1996 and September 1996. Co-disposal of deslimed cemented tailings (CHF) and suitably graded rockfill (RF) in certain ratios produced the rocky paste fill. The RPF behaved like a cohesive paste with very high proportion of rockfill in the mix. Several large-scale mixing trials and drop tests proved that the rocky pastefill results in a homogeneous fill mass after placement. Segregation of RF was a common problem with MIM's traditional cemented rock fill (CRF), which is a combination of CHF and RF. The segregation was eliminated and a non-segregating paste like fill was created by optimising the particle size distribution of RF, and combining the RF and the CHF in optimum ratios. In rocky pastefill, the excess water in the cemented deslimed tailings slurry is taken up by the rockfill as the surface moisture on the rockfill particles and also as pore water between the particles. This results in thickening of the CHF, and the resultant mix is a non-segregating cohesive paste, which can easily spread to any horizontal distance inside a stope at a very low surface angle. The rocky pastefill releases no free water and relatively more pervious than the standard CHF due to rockfill component. With an average cement addition of 1.5 to 2% the rocky pastefill can develop higher strengths over 1Mpa. The rocky paste fill is applicable in many situations and can accommodate a variety of coarser materials that would be available in different mine sites. This paper present the research work and the experience associated with the rocky paste fill, and gives clear design principles for any potential users.

Jan 1, 2001

By P. Asadollahi, M. Invernizzi

"This paper describes the innovative full-face conventional tunnel excavation technology, with its advantages in terms of savings and safety. The full-face approach has been developed throughout the experiences gained in tunnel construction. The innovative design approach is focused primarily on the deformation response of the ground acting first and foremost ahead of the face, which is analyzed, predicted and controlled by pre-confinement of the core. The advantage of this method is particularly evident in difficult grounds. This paper will present the outstanding benefits given by the adoption of the full-face approach in two projects, the “Sochi” and the “Visnove” tunnels. THEORY AND DESIGN ASPECTS OF THE FULL-FACE EXCAVATION The main challenges in tunnel and underground construction industry are gathering the design data from the ground that is being excavated and foreseeing the critical stage during construction, where the materials are in its most critical configuration. These challenges shall be addressed during excavation when the lining and the excavation disturbance have not yet reach the equilibrium. The in situ stresses in the ground are redistributed (forming an “arch-effect”) around the opening, with zones of increased stresses around the walls of the excavation (Figure 1). The distribution of the stresses can be close or far from the excavation profile, depending upon having a ground capable of withstanding the deviated stresses well or unable to withstand them, respectively. In the latter case, the ground will plasticize and deform in proportion to the volume of ground involved in the plasticization phenomenon. When the ground completely cannot withstand the stresses redistribution, it will cause the collapse of the excavation. While in the first case, the arch effect occurs naturally, in the second case, it does occur naturally only when the ground is stabilized properly. In the case of collapse, the arch-effect must be produced artificially operating on the ground prior excavation. The design should be based on the understanding of if and how the arch-effect can be mobilized during tunnel excavation and ensure that is formed by calibrating excavation and stabilization operations appropriately. The arch-effect is function of the medium that is being excavated, the action taken to excavate and the reaction expected following the excavation."

Jan 1, 2018

By Gordon R. S. Smith

This paper is in two parts. The first part describes Membrane Back-Pulse Filtration and the effects of very short filter downtimes on cycle filtration rates. Part II describes the use of Membrane Back-Pulse Filtration for combined thickening and polishing soda ash thickener feed material followed by a description of computer modeling of CCD circuits by Iterative solver.

Jan 1, 1991

By Fabiola Espinoza Carmona, Elena Chiriotti, Edoardo Misano

"INTRODUCTION Ganntas Tunnel is part of the modernization project of the railway between Alger and Oran, in Algeria. In order to double and rectify the existing line between El Affroun and Khémis Miliana, the alignment foresees the excavation of a 7 km-long twin tunnel. The excavation works started in June 2011 with the contractor CCECC, under the supervision of SYSTRA. Excavation is driven in conventional method by hydraulic hammer simultaneously on 8 different faces since excavation was started also from a junction window towards the middle of the tunnel. The minimum longitudinal distance to be respected between two contiguous tunnel faces has been set to 30 m. The tunnel cross-section is a 70 m² oval shaped profile, temporary support consists of shotcrete, bolts and steel ribs. A 30 to 50 cm thick cast in situ concrete final lining has been provided as well. When the tunnel reached a fault zone in soft clayey marls extreme squeezing occurred, works were stopped and re-profiling operations were carried out along more than 100 m. To date, works proceed at slow rate since high convergences are still monitored and completion of works is not expected before December 2016.GEOLOGY The project is located within the Tellian Atlas mountain area, including in particular the Djebel Ganntas massif in between Mitidja and Chleff plains. Djebel Ganntas is characterized by an extensive massif aligned in East-West direction with smooth slopes made of soft clays that emerge in multiple cliffs and ravines. On the top of it, along the edge, a more recent sandstone formation is found. The existing data on the geology did not allow to establish an accurate geological model at tender stage. In-situ investigations allowed at design stage to identify a Quaternary alluvial cover of clays and gravel, followed by a Miocene stratum divided in a sandy top layer and a lower clayey layer. From a structural point of view, geological maps suggest a north direction dip of layers, but the in situ surveys showed that layers were highly folded. The lack of information at tender stage on the structure of the geological series should have triggered an extensive investigation campaign at detailed design stage which did not take place causing serious consequences on costs and time at construction stage."

Jan 1, 2016