Search Documents

By Kotaro Ohga, Gota DEGUCHI, Kiyoshi HGUCHI

The situation of Japanes coal mine is in the severe enviroment, because the policy on coal mining has changed. Every year one or two coal mines will be foced to close. To continue the production of coal, we have to reduce the cost of production. Therefore, the mining by longwall method which is more than 250m was attempted at Taiheiyou Coal Mine to reduce the cost and this mining method have had successful results. To get successful results by this mining method, the controlling and prediction of gas emission from the longwall panel will be most important things. In this paper, the comparison of the predicted gas emission from the mining panel based on the measured gas content by using new device with the observed results is described.

Jan 1, 1993

Diesel engines are used in underground mining 1 throughout the world. Exhaust gases from those engines contain toxic components. To protect quality in underground mines, diesel emission control was introduced decades ago, many years before the first surface applications. Today, emission controls, such as catalytic converters, are standard on underground diesel engines in countries concerned with occupational safety and health. Nett Technologies manufactures a range of diesel emission-control devices for underground mining. Emission problems are not the same at each mining operation. And there is no universal control technology. The selection of exhaust aftertreatment technology depends on raw exhaust emissions, particular emission problems, fuel quality and economics. Some of the technologies that have been used in underground mining to control diesel emissions include catalytic converters, diesel filters, fume diluters and water scrubbers. Table 1 compares the effectiveness of these technologies to control the particular components or aspects of diesel emissions.

Jan 1, 1997

By Edward DeLilla

Formalized technical audits for mining machinery during manufacturing are a fairly new concept to the North American mining industry. Although used extensively elsewhere, especially in Australia, the concept of independent auditing of machinery design and manufacturing has been slow to gain acceptance in the United States and Canada. Simply stated, a technical audit is an independent, third-party review of all or specific portions of machinery design, manufacturing and assembly to verify compliance with purchase specifications and suitability of the machinery for the specified application. If specified correctly, the useful life of different kinds of structural and mechanical components can be extended beyond normally accepted usage. There is no reason why, if properly designed and built for the application, major structural components on mining machinery cannot be made to last for 20 years before being rebuilt. Also, gearing can be made to routinely last for 15 years.

Jan 1, 1995

By Wolfgang H. Roth, Stephen J. Navin, Samuel K. Louis, Anthony F. Stirbys

This paper presents a case history of the design and construction of the access shaft and cross adit utilized to gain access to the Los Angeles Metro Rail tunnel alignment, at the A146 Contract site. The access shaft, a 14 m (45 ft) inside diameter structure, was constructed using ring beams and lagging with concrete backfill to a depth of 18.59 m (61 ft). The cross adit was hand excavated in sequential benches using liner plate, arch ring beams, and posts for support. The sequence of excavation and support placement are discussed. Soil conditions encountered at the project site are discussed together with the development of the design criteria. Instrumentation data collected during the excavation are also presented.

Jan 1, 1989

By R. Kramer

The Process Mineralogy review arrived too late to appear in the May issue. The Process Mineralogy Committee scheduled programs with both SME and The Metallurgical Society. At the 1991 SME Annual Meeting in Denver, CO the committee sponsored five sessions containing 31 papers. Four process mineralogy sessions were sponsored at the 1992 annual TMS meeting in San Diego, CA. Process mineralogy is used to understand and evaluate mineral behaviors during mineral beneficiation, phase reactions during metallurgy, recoveries and reactions of precious metals during processing and mineral and phase behaviors with respect to environmental problems. The most recent refinement in mineralogical studies with respect to mineral beneficiation has been the wider use of image analysis and combined materials balancing techniques of image analysis data. Image analyzers that can perform analysis with respect to mineral beneficiation are expensive. They are used only for solving major processing problems. Nevertheless, the methodology of analysis continues to be refined. Much better data are collected, and methods of evaluating the data continue to improve. One interesting development involves modifying the ultrasound unit used in medical studies to perform a three-dimensional analysis of ore particles.

Jan 1, 1992

At present, increasing focus of public perception is placed on the environmental and social benefits, risks and impacts of metals and metal-bearing products. To address these issues, the concept of product stewardship has recently been introduced into the political debate. In this paper, results from a survey of existing environmental and social reporting practice in the copper mining, smelting, refining and fabricating industry are presented. In this context, particular emphasis is placed on the reporting practice regarding products and product performance over the life cycle. In a few companies there has recently been a shift towards adopting product stewardship principles and putting them into action. As part of an ongoing exercise within the Non-Ferrous Consultative Forum on Sustainable Development sponsored by the International Copper Study Group (ICSG) key issues of interest to the non-ferrous metals sector are being addressed. The Forum, for example, has developed a series of principles, criteria and indicators that could form the basis for a voluntary, industry-lead product stewardship scheme. Current achievements and way forward of this product stewardship initiative will be presented.

Jan 1, 2003

By Lynn E. Bowman

Efficient filtration of fine kaolin particles plays a crucial role in the processing of raw kaolin to a marketable product. Filtration can often be the rate-controlling step of the whole process. Consequently, plant production depends on the rates being achieved in filtration. To alleviate the bottleneck in production, Nalco Chemical Co. initiated a reagent development program to chemically enhance the performance of the filtration units. Filter aids of different classes were assembled and evaluated in bench simulations. These included reagents whose primary mode of functionality were coagulation, flocculation, thickening and combinations of each. This article discusses the development and application of a new reagent that improves the filter production rate with minimal impact on filter cake percent solids. Plant data indicate that this reagent can increase production rates by as much as 35% on clays of varying particle size, as well as clays that are calcined. The reagent's impact on solids content, re-slurrying characteristics, Brookfield and Hercules viscosity and drying is within the standards set by plants that evaluated and now use this product.

Jan 1, 1993

By J. C. Yingling, V. Badaker, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

The University of Kentucky has developed reclamation cells at a surface mine in southeastern Kentucky to evaluate the impact of spoil handling (reclamation methods) and compaction alleviation methods on the physical properties of replaced growing media and on tree survival rate. From 1997 through 2001, penetration depth, penetration resistance, bulk density, and tree survival data have been collected at the reclamation cells and correlated to determine the relationships that exist between the soil physical properties at the site and tree survival. Regression models have been developed for each reclamation method evaluated using the collected data to predict tree survival rates on reclaimed surface mined lands as a function of the soil physical properties of the replaced growing media. Procedures have been developed for handling soil/spoil during reclamation that can minimize compaction in the replaced growing media. Procedures have also been developed for alleviating compaction in growing media on reclaimed and orphaned surface mined sites. These procedures, if implemented, will increase the potential for reforestation success. Finally, procedures have been developed for collecting soil physical property data for use in evaluating the suitability of spoil conditions for reforestation.

Jan 1, 2003

By Mark E. Smith

Large scale copper heap leaching in Chile began in November 1980 when the Lo Aguirre heap leach project was put into operation. At almost the same time, El Indio gold mine began production. While El Indio was not a heap leach project, it was Chile's first major bulk tonnage, open-pit gold deposit. This paved the way for the introduction of North American gold heap leach technology in the early 1980s. Heap leaching has become more popular in Chile during the past five years because it allows the exploitation of large but relatively low grade ore bodies at a reasonable cost. Pioneering research in hydrometallurgy carried out at some Chilean universities and at the Centro de Investigaciones Minero Metalurgicas (CIMM) played an important role. There are more than 10 large copper heap leach and solvent extraction/ electrowinning (SX/EW) process plants in different stages of development in Chile. Total production from these facilities will eventually increase Chile's present copper exports about 50%.

Jan 1, 1995

By A. G. Sciulli, G. P. Ballock, G. Hearnshaw, K. K. Wu

Waste disposal underground is the most effective method when viewed from an environmental aspect. As costs of other methods of disposal continue to escalate, the cost effectiveness of underground disposal during the mining cycle becomes increasingly attractive. The use of concrete for sealing abandoned mines has proved to be suspect when associated with a relatively incompetent adjacent strata due to its shrinkage characteristics. Complete failure of the plug has been known to occur in some instances. A more effective, cost competitive seal can be obtained using pneumatically stowed material and incorporating a polyurethane grout, which has greater adhesion characteristics than concrete. Injection of the surrounding strata and of the stowed material helps to ensure an impervious barrier and prevent the plug from moving when subject to high pressure heads. When properly placed, impervious seals cause the old workings to flood, raise the mine pool level, and thus eventually eliminate the potential for oxidation, which is the primary cause of acidity in the water

Jan 1, 1987

By G. Trusler, P. Dama, C. Buckley, C. Jänisch

In the 1990s, Cleaner Production (CP) approaches were successfully introduced to a number of industrial sectors in South Africa. Building on this success, the South African Water Research Commission has commissioned a 3-year study to investigate the use of CP and its related set of environmental assessment and management tools in the mining industry. A scoping study is being carried out on the current knowledge of CP approaches being used in the industry, as well as the proactive and preventative measures being undertaken. One of the significant findings of the scoping study is that distinct differences exist between the larger global companies and the smaller local companies. Being a water research project a key focus area of the project is to reduce the impacts related to mining on the South African water resources. Some of the significant water related threats identified include acid mine drainage, the shortage of the resource and the effects of inter-mine flow.

Jan 1, 2005

By Thomas W. Camm

A WINDOWS-based object-oriented expert system for prefeasibility evaluation of hard rock mines is being developed at the Western Field Operations Center (WFOC) of the Bureau of Mines. Designed for use with the Bureau's Cost Estimating System (CES), this expert system assists an evaluator in choosing an underground mining method, and the related design parameters. The system provides the engineering and design guidelines necessary for an evaluator to perform a prefeasibility type cost estimate.

Jan 1, 1992

By Walter J. Pachucki

Mining equipment maintenance costs account for a major portion of a mine’s total operating expense. A reduction of maintenance costs while providing required equipment availability translates directly into increased profit for a mine. Therefore, having in place a successful maintenance program can be management’s most direct route to increased profits. One key element of a successful maintenance program is a practical and effective recordkeeping and information system. In recent years, many mining operations have invested in the development or purchase of computerized maintenance information systems. Computerized maintenance information systems can serve as a valuable tool in managing mining-equipment maintenance. They can also be a costly, frustrating waste of time. Why are some systems successful at one operation but a failure at others? Should all mines use computerized maintenance information systems? How does management decide what maintenance software is best for their operation? In an effort to to answer these questions and to better understand what is required to make a mining maintenance information system successful, a study was recently conducted on maintenance information systems used in the mining industry.

Jan 1, 1991

By Michael E. Allen

The building of sanitary and storm drainage sewers in urban or environmentally sensitive areas often requires the use of tunnel construction procedures. While hydraulic considerations may require only small diameters, traditional tunneling techniques make small sizes the least economical. Current state-of-the-art techniques using highly mechanized systems of pipe jacking can provide cost effective solutions to the problems of construction of small size tunnels. The characteristics of mechanized pipe jacking allow rapid advances under difficult ground conditions. The basic pipe jacking cycle is used with a variety of excavation systems to permit the contractor to satisfy engineering as well as economic parameters. These characteristics and several of the systems available are outlined.

Jan 1, 1981

By Norman F. Sweeney, H. John Hovland

Over one million yards of granite were excavated for the Helms Pumped Storage Project, including a large underground powerhouse complex. Site investigations and in situ stress measurements were essential elements of the project design and provided the necessary geologic parameters for executing a finite element study of the powerhouse. A construction monitoring program, of geologic mapping, field instrumentation, and rock mechanics testing was then designed and has been successfully implemented. This paper reports on the scope of this construction monitoring program and explicitly compares the measured deformations to those predicted. As a result of this recent field experience the assumptions used in the finite element program are reexamined.

Jan 1, 1981

By Yuusaku Tominaga, Sukumar Bandopadhyay

A power-series trend curve of elapsed time was estimated by using time series data of measured concentrations of carbon monoxide in the Taiheiyo coal mine, Hokkaido, Japan. The difference between the moving average concentration data and the estimated data from the trend curve showed linear correlation when plotted on a normal probability paper and a correlation coefficient value of 0.99. It is concluded that the estimate of carbon monoxide concentration using moving average values of concentrations compares very well with the results obtained from the trend curve within the three-sigma (standard deviation) range of the distribution. Thus, it is believed the results can be used to monitor and detect abnormal ventilation conditions in a ventilation network such as the occurrence of spontaneous combustion at an early stage.

Jan 1, 2002

By Dave Rogstad

The DART NC-1B Tunnel Project consists of two 5,100 m TBM excavated tunnels, a principal underground station, a partially completed future station, a surface station, and eight associated ventilation shafts and exit tunnels. This paper presents a case history of the project's construction, and will focus on six topics that give this project a unique and unusual history; the TBM excavation, two major differing site conditions, roadheader excavation, polyfiber reinforced shotcrete lining, the NATM design geometry, and a design/build type of contract.

Jan 1, 1995

By Joachim H. Schubert, David G. Hulbert, Ian K. Craig, Roger G. D. Henning

This paper presents a stabilizing controller for flotation plants which uses a quasi-multivariable technique. The controller monitors all the levels in the plant, and by anticipating interactions between various parts of the plant, is able to stabilize the plant far more successfully than the normal plant control. Once stabilizing control has been achieved, optimization of the process becomes easier and more sustainable. An estimate of the improvement in metallurgical performance is made and a singular value analysis was conducted to verify that the multivariable algorithm will theoretically control better than a collection of individual PID loops. Metallurgical results are presented to show that the improvements are attainable in practice. Control by the Mintek algorithm was alternated with normal plant control, to show that the improvements are statistically significant.

Jan 1, 1995

Laboratory techniques have been developed at the Julius Kruttschnitt Mineral Research Centre which relate comminution energy to size reduction. These relationships have been applied in the mathematical modelling of autogenous and semi-autogenous mills. Since their development in 1987 these models have been successfully used in many wide ranging design and optimization studies. A description of the basic structure of the models is presented with particular reference to ore characterization. Two case studies are presented which illustrate their effectiveness in evaluating and predicting the effects of circuit changes.

Jan 1, 1992

By William A. Holgate

Coal production in the in the Powder River Basin began its tremendous expansion during the boom of the mid-1970s. New mines were opened from 1976 through the early 1980s. This expansion soon placed Wyoming at the top of the list of coal producing states, where it has since remained. Mines are operated by large companies, with safety and production having equal priority. These mines have been some of the safest ever in the coal industry. Many Sentinels of Safety Awards have gone to them. Safety programs are varied, but there are commonalities. Mine safety at Wyodak Extra training is required of all supervisors. The company offers to pay for any additional first-aid training that employees participate in. Safety departments conduct weekly safety talks. All employees receive the monthly magazine Family Safety and Health compliments of Wyodak. Electricians receive extra training on electric wheel motors, from General Electric. Equipment operators receive extra training from Dresser.

Jan 1, 1994