Search Documents

By S. A. K. Forson, Newton A. Amegbey

In order to investigate production decline in Tarkwa Goldfields Ltd., located in a tropical rain forest, amongst other areas, a health survey was conducted with the aim to see 1. The health status of the workers. 2. Which parameters carry the most information about the health situation and which of them can be applied easily during screening programmes. 3. What steps could be taken to improve the situation. In all 249 workers were investigated. A non-invasive method involving taking of body weight and arterial blood pressure was used. All subjects were required to answer a questionaire. Emphasis was placed on the history of malaria and diarrhoea within the last six months. Both management and workers co-operated fully. Another set of 110 workers from a neighbouring tyre factory were also investigated for control. Among the underground workers, the percentage body weight loss during a shift increased with decreasing body weight. Dehydration levels could be as much as 4 to 5% of body weight. This could be attributed to the fact that workers took insufficient or no water during the shift. The health status of the mine workers was generally poor and in our opinion malnutrition combined with malaria severely threatens the health and well-being of the workers. Hypertension is also a problem. An improvement in production is intimately linked with the well-being of the workers.

Jan 1, 1989

By A. K. Bakshi, Komar S. Kawatra

A plant trial of a new on-line pressure vessel rheometer for slurries, developed at Michigan Technological University, was carried out at a nearby copper concentrator. The rheometer measured the flow curves (shear stress vs. shear rate) of chalcocite slurries. Viscosity of non-Newtonian slurries changes with shear rate and so, for such slurries viscosity measurement at a single shear rate (often seen in the literature for grinding and classification studies) cannot be correlated to process performance. For these slurries, viscosity at various shear rates can be measured from flow curves generated by the pressure vessel rheometer. Other rheological properties, such as flow type and yield stress can be determined by this rheometer to better characterize the slurries. The slurry at the copper concentrator consisted of ground chalcocite ore. The solids content in the slurry varied between 30-60 % by weight. Top size of the particles was 125 micron, and 80% passing size was 34 micron. Measurements by the pressure vessel rheometer showed that most of the slurries had pseudoplastic flow at shear rates below -3000 sec-l, where the viscosity of the slurry decreased with increase in shear rate. Above -3000 sec-l, like a Newtonian fluid, the viscosity of the slurry remained steady. Flow curves and viscosity from the pressure vessel rheometer were verified with a Brookfield viscometer and a vibrating sphere viscometer, and the results were found to be accurate.

Jan 1, 1997

By T. N. Moore, E. M. De Souza

Vibratory hand-tools can produce Hand Arm Vibration (HAV) Syndrome in their operators. This disease, often called Vibration White Finger, can cause varying levels of hand-arm discomfort and, in severe cases, impairment. In addition to the human suffering, there are also significant economic repercussions for industry. These include reduced operator efficiency, lost time through increased absenteeism and increasing compensation awards. In the mining industry, jackleg rock drills are a particularly troublesome source of hand vibration exposure. As a result, a significant amount of work has focused on redesigning rock drill handles to minimize hand-transmitted vibration. This paper details the results of a study undertaken to determine the effectiveness of using elastomer covered ("cushioned") handles in place of the standard steel design. The results indicate that, for a particular cushioned design, the overall acceleration level experienced at the hand-handle interface can be reduced by as much as a factor of three, relative to the steel handle. It is also shown that this reduction takes place predominantly in the frequency range above 500 Hz, with performance improving with increasing frequency. Qualitative evaluation of the cushioned handles by the drill operator indicates a significant increase in comfort over the standard steel handle.

Jan 1, 1992

By J. Pflieger

The International Iron and Steel Institute (IISI - http://www.worldsteel.org) has initiated the development of a comprehensive freely-available, internet-delivered package of highly interactive e-learning resources for undergraduate students and steel industry employees. The resulting e-learning environment (http://www.steeluniversity.org) creates a ?one-stop? shop covering all aspects of steelmaking, steel products and applications, the underlying scientific and engineering principles, industrial and academic collaboration, as well as environmental and sustainability issues relevant to the steel industry. The module entitled ?Sustainability, Steel and the Environment? of the steeluniversity.org provides interactive e-learning resources on the following topics - Sustainability. - Principles of Life Cycle Thinking. - Environmental Life Cycle Assessment. - Application of Life Cycle Assessment. The aim of this particular module is to enable the learner to identify relevant environmental parameters over the life cycle of steel products as well as to learn about the resulting environmental effects and impacts. Furthermore he/she will be enabled to explain the basic idea of Life Cycle Thinking and Life Cycle Assessment (LCA) in terms of Goal and Scope definition, System Modelling, Life Cycle Inventory (LCI), Life Cycle Impact Assessment (LCIA) and Interpretation. In addition, the learner can explore selected LCA scenarios facing the steel industry and its customers in the automotive and construction sectors.

Jan 1, 2007

By Steven H. Brown

Ore bodies which were once uneconomical to mine by conventional methods such as tunneling or open pits, have become attractive due to the development of nonconventional techniques, involving considerably less capital expenditure. Technologies such as uranium solution mining or in-situ leaching, have enabled commercial scale mining and milling of relatively small ore pockets of lower grade, and may make a significant contribution to overall U.S. uranium supplies during the next 20 years. Commercial size solution mining production facilities have operated since late 1975. Solution mining involves the pumping of ground water, fortified with oxidizing and complexing agents into an ore body, leaching and solubilizing the uranium in-situ, and then pumping the solutions to the surface where they are fed to a processing plant. Processing involves ion exchange, precipitation, calcining, and packaging operations. This paper presents an overview of the solution mining process and the health physics monitoring programs developed over the last four years at several production facilities as a result of the radiological character of these processes. Although many radiological aspects of the process are similar to that of conventional mills, conventional-type tailings as such are not generated. Some special monitoring considerations are presented which are required due to the manner in which radon gas is evolved in the process and the unique aspects of controlling solution flow patterns underground. An overview of the major aspects of the health physics compliance and monitoring programs that have been developed are discussed.

Jan 1, 1981

By Betty L. Gibbs

A short course, held during the SME Annual Meeting in Phoenix, AZ in February, focused on software for surface and underground mine modeling. The objectives of the short course were to review techniques for surface and underground mine planning. Mine planning software vendors were invited to demonstrate how their software runs, given a standard data set. Six vendors of mining-specific software participated in the workshop. They were Exploration Computer Services (MINEX 3D), GEMCOM Services, Inc. (PC-MINE), KJRA Systems (VULCAN), Mine Development Associates (SURPAC), Micromine and MINEsoft (TECHBASE). Data set A data set was created to challenge the capabilities of each vendor's software. The criteria used for the data set selection were: • a minimum of 300 drill holes; • the data must include topography, drill hole survey, assay and formation contacts; • the deposit was multimetallic; and • there was the potential to be mined by surface and underground methods. The data set used was an actual, complex copper ore body with a small amount of gold. The ore body was close enough to the surface to be mined by surface techniques. Part of it, though, was also amenable to underground mining. To further complicate the problem, a river ran across the area of the ore body. This presented mine planners with the problem of either moving the river or mining around or below it. The ore body had not been mined, so no data was available for the tons and grade actually produced. Data for the mine planning problem was distributed to each vendor about two months before the short course. They had the opportunity to load the data into their systems, build an ore body model and perform preliminary work. During the first day of the workshop, the vendors received problems concerning the ore body. They went to work on their machines, attempting to show short course participants how their software could help solve the problem.

Jan 1, 1992

By J. Alton Burks, Roy C. Bartholomae

The chain conveyor is utilized extensively in underground mining to convey raw ore, especially coal. It is estimated that several thousand loading and continuous mining machines rely on this type of conveyance. Although the chain conveyor is both efficient and highly reliable, its use is generally associated with the production of noise levels that often exceed 105 dBA at the operator's position. Thus, it is one of the most significant contributors to the occupational noise problem experienced by miners in the underground coal mining environment. Conventional engineering noise controls that result in an average reduction of 4 dBA have been previously designed and implemented. However, a novel solution involving a change in conveyor operation has been proposed that takes advantage of two aspects of conveyor noise: 1) conveyor noise has an approximately cubic dependence on conveyor chain speed and 2) due to the damping provided by coal, a full conveyor is 5 dBA quieter than an empty one. An engineering analysis has shown that a significant reduction in the operating noise level of a typical continuous miner can be achieved through the use of an adjustable speed drive automatically controlled by a coal loading sensor that maintains a full conveyor at all times. The potential reduction depends primarily on the mining conditions (coal seam thickness and the presence of either rock or water) and varies from 7-18 dBA. Other benefits to be derived from the use of a variable speed drive include reductions in power consumption, dust, and maintenance costs.

Jan 1, 1992

By G. E. Bandelis

In this paper, solid bed erosion processes and the mechanisms involved when a two-phase liquid-solid mixture flows over a bed of solids in a horizontal annulus are analyzed. There are few such studies available with some authors arguing that the flow rate for erosion is always less than the flow rate for the suspension of solid particles thus necessitating further study and analysis of such phenomena. Tests were run to determine the mechanism of erosion and the erosion velocities of the solid bed formed in a concentric annulus for three flu-ids, water, a low concentration water solution of Carboxyl-methyl-cellulose (CMC), which behaved as a Newtonian fluid and a higher concentration CMC water solution which behaved as a power law fluid. Glass spheres of 2 mm nominal diameter were used as solids. The flow rate at which erosion occurred together with the mechanism of bed erosion were determined visually, while the whole process was video recorded. Our tests indicated different erosion mechanisms and different erosion velocities for the three tested liquids, with the liquid viscosity playing a major role. The first mechanism, observed for water flow, gives erosion from the front of the bed while the second mechanism, observed for the flow of the two viscous fluids, gives erosion from the top of the bed. The role of each of the parameters to erosion is investigated, whether it is turbulent flow with the turbulent fluctuations being more capable to remove the solids from the formed bed or whether it is liquid viscosity, which results in the hydrodynamic shearing force. The results demonstrate that liquid viscosity plays a role in the erosion mechanism and yields different erosion velocities of the solid bed hence, it should be taken into account when modeling flow pattern transitions for solid-liquid flows. Prior studies have not identified this and it could be the reason of the disagreement between theoretical models and experimental and field data.

Jan 1, 2006

By D. E. Piggott, B. E. Hartmann

The thought of constructing an intake shaft five miles from the shore and 142 feet below the surface of Lake Huron from the bottom up sounds like a questionable venture. Why would one want to raise a shaft from the bottom at the end of a 16 foot diameter, six mile long tunnel to within six feet of the bottom of Lake Huron? The answer lies in the fact that Lake Huron is seldom a tranquil lake. The construction period and workable days from the surface are limited. Two previous attempts to construct this intake shaft by conventional means had been thwarted by lake storms. These approaches were circular sheet-piling cofferdams with the intention of sinking a 30 foot OD, five foot wall thickness concrete casing in the center. However lake storms, particularly in the months of November and December, proved disasterous. The last attempt was halted in December 1970 when three of the seven circular cofferdams on the north side were destroyed by pounding waves. Then, due to the nature of the technical difficulties and limited construction schedule time, it seemed desirable to devise a way in which construction could proceed without being too lake-sensitive. Obviously, if men could work from the tunnel and proceed upward toward the bottom of the lake, not having to worry about the soil collapsing and bringing the lake in on their heads, the construction would be unimpeded by adverse weather. The answer to this, however, required techniques beyond the ordinary. Approximately two years previous to the start of this shaft, nine shafts had been efficiently constructed on the same project site

Jan 1, 1974

By Joseph M. Keane

Introduction The English word "sedimentation" is derived from the Latin verb "sedere" meaning to sink down. As a mineral processing unit operation, sedimenta¬tion has been defined as the separation of a suspension into a supernatant clear fluid and rather dense slurry containing a higher concentration of solid (Brown, G.G. 1960). Sedimen¬tation has been historically subdivided into thickening, which has the primary purpose of increasing the solids content of one of the thickener prod¬ucts relative to the feed stream, and clarification, which has the primary purpose of removing solids from the feed stream to produce a product essentially free from particu¬late matter. There is no absolutely precise distinction between these subdivisions and in certain applica¬tions, both objectives can be accom¬plished. Major Design Factors The capacity of conventional metal¬lurgical sedimentation devices is a function of slurry throughput and its attendant settling rate. Important factors, recognized by early investigators (Taggart, 1972), which influence the settling rate of a given metallur¬gical slurry include: Feed dilution or solids-liquid weight ratio Size and shape of the particulate solids Specific gravity differential between the solids and liquid phases Presence of electrolytes and/or flocculants Pulp viscosity Slurry temperature In addition to the foregoing histor¬ical factors, recent investigators have noted (Pearse, M.J., 1977) that other parameters which may have an influence upon settling rate and, thereby, thickener performance include: Method of flocculant application Particle size distribution Particulate wetting characteristics Feeding arrangements Rake speed and type Existence of convection currents Wind disturbance Evaporation All of the above factors should be examined and the effect upon thick¬ener performance brought about by manipulating the factor over the expected operating range should be determined if performance optimization is desired.

Jan 1, 1986

By E. Bane Kroeger

Plane failure in rock and soil slopes is usually caused by the intersection of a discontinuity plane with a slope face. Normally, these discontinuities are weaker than the surrounding intact rock and provide a surface along which movement can occur. The discontinuities are typically analyzed to determine the stability of a particular slope. One problem that arises when evaluating the stability of a planar feature is that the method for planar analysis is two-dimensional and has difficulty dealing with planes that are oblique to the slope face. Several researchers have stated in the past that planar failures are a special case of wedge failure. Wedge failures occur when two planar discontinuities intersect in an unfavorable manner. Sliding can occur along the intersection of the planes. Wedge failures are very common in rock slopes and can often be problematic. Wedge stability analysis methods are typically three-dimensional and can analyze planar features that are very oblique to the slope face. Wedge failure analysis can also be used to determine the stability of planar features with good success. One advantage to using wedge analysis over plane analysis is that a tension crack can be both non-vertical and oblique to the slope face in the wedge analysis. This allows the engineer to more closely match field conditions. It also negates the need for the engineer to have two separate software packages to analyze a single slope, saving both time and money.

Jan 1, 2002

By E. (Walt) van Walsum

The MPTM was first applied in the U.S.A. in 1950 as described by Lewis, W.E., 1951. The method was then abandoned in the USA and rediscovered some 20 years later in France where it was greatly improved and widened in its scope of application. It was subsequently successfully introduced to Italy and Spain. The technique, at its present stage of development, provides solutions to tunneling in soil and in the softer rock types, which often were troublesome geological environments for tunneling. When used in conjunction with drilling-and-blasting, over break, excessive vibration, noise and fissuring of the rock can all be avoided. When used as an alternative to the New Austrian Tunneling Method (NATM), the MPTM provides safe, full face tunneling in stead of multiple headings, excavated sequentially; in addition, surface settlement can be virtually eliminated. When used as an alternative to a TBM, the method's flexibility and low capital cost make it attractive. This attractiveness is enhanced when ground conditions are erratic or when the length of tunnel to be excavated is limited. The method holds promise for tunnels of large cross section, to be excavated in soft ground or rock with unconfined compressive strengths of less than 80 MPa (11 600 psi). While in itself not new, recognition and development of the method's potential are. Further development work, aimed at increasing the range over which the MPTM can be applied, is in progress.

Jan 1, 1993

By Philip L. Hageman, Paul H. Briggs

An important tool for use in the geochemical assessment of abandoned mine-waste piles is a leach procedure that can easily be done in the field and used for on-site screening of historic mine-waste material. We have developed a simple field leach test that is an effective indicator of waste pile geochemistry and can be used in order to establish the relative geochemical fingerprint for a given pile. This simple procedure also provides indication of the potential chemical composition of run-off from the weathered surface of these piles. As part of developing the technique, a comparative study was carried out on eight mine-waste composite samples from different deposit types. Splits of all eight composites were leached using the field leach test procedure and a modified version of EPA Method 1312 (SPLP). We found that the field leach test consistently provides relative indication of leachate geochemical trends comparable to leachate data derived from the more regulated, time consuming and laborious EPA Method 13 12 (SPLP).

Jan 1, 2000

By Thomas J. Rudolphi

Efficient transport of bulk materials by belt conveyor systems is an important engineering design issue, especially as conveyors become longer and power requirements increase. It is well known within the industry that the parasitic energy loss of a belt conveyor, due to the indentation of the idlers into the belt backing material can be upwards of half the total energy required to drive it on a horizontal flight. Other loss sources includes the rolling resistance of the idlers, belt/roller misalignments, material trampling, frictional and acceleration losses on loading, etc., but energy absorbed by indentation of the belt backing as it passes over each successive idler is the dominant power consuming factor. INDENTATION LOSS MODELS Models to predict the rolling resistance of a cylinder (idler) on a viscoelastic foundation (backing material) have been available for some time. As a contact problem, it is nonlinear (contact length or indentation depth is a dependent on the load and vice versa) in load/deformation response. Rubber backing material is generally assumed to behave as a linear viscoelastic solid, even though it is known that most rubber compounds retain linearity only at very low strains. Because completely general solutions are impossible, practical solutions require simplifying assumptions. Those assumptions relate naturally to two separate pans of any analytical model: I. The deformation model-aspects of the problem relating to the geometry, boundary conditions and kinematics of how the material deforms. 2. The material model-aspects of the problem relating to the material properties, or constitutive relationships, i.e., the stress/strain relationships.

Jan 1, 2008

By Charles L. Kimbell

In 1989, worldwide total mineral industry activity registered advances from 1988. The advances may not have been as noteworthy as in 1988, but they can be regarded as a worthy theme for this article. The momentous political events throughout the centrally planned economy world had only a modest impact on actual 1989 industry performance. But these events have such potential for worldwide changes in economic activity in future years that they dwarf the actual happenings of 1989 in the minerals industry. Perhaps most significant factor here is the rapidity with which these changes have occurred. The end of World War II saw the almost immediate division of the world into major economic blocs. Since then, mineral industry activities and other industrial operations have been governed, to a considerable extent, by this partitioning. The developed market economy nations have operated as a group, the centrally planned economy states as another group. And these two groups essentially have vied for recognition in mineral industry operations in the developing economy states of Asia, Africa, and Latin America. The boundaries of these country blocs were fixed in the late 1940s and early 1950s. They were not markedly altered in the ensuing 40 years. We have seen the establishment of the Organization of Petroleum Exporting Countries, the continued Arab-Israeli confrontations in the Near East, the upheavals surrounding the rise of Moslem Fundamentalism in Iran, and the establishment of Soviet-oriented governments in Cuba and Nicaragua. These events have had notable effects on the world economy. But they have done little to change the pattern of market economy states functioning as a competitive bloc with the centrally-planned economy countries.

Jan 1, 1990

By Ing. E. h. Martin Herrenknecht

The paper will describe a number of developments and innovations now in use in microtunnelling machines. These include the use of fuzzy logic steering systems, the proven ability to successfully undertake complex curved microtunnel drives, the ability to complete ultra long drives using microtunnelling techniques, and machines with access to the face of the machine from inside the machine. The ability to tunnel in relatively hard rock utilizing a rock head with back loaded cutters changeable from inside the microtunnel machine and the ability to utilize microtunnel machines in multi modes, such as hard rock mode, “open” mode, EPB mode, and slurry mode with the same base machine again with access to the face of the machine will be described. In addition, the latest computer technology gives the operator “full visualization” of machine functions together with the ability to data log machine operating parameters. Reference will be made to a number of projects worldwide recently completed or under way where these innovations have successfully been utilized.

Jan 1, 1999

By R. C. Kirkman

Your interesting and well-written paper brings up the issue of the purpose or use of a mineral property appraisal, specifically the value of these evaluations when the quality and quantity of the mineral resource to be exploited have not been thoroughly investigated. I am not a practicing professional in regards to valuation of limestone investment opportunities. I simply wish to make a few generic observations about the appraisal process in order to stimulate meaningful thinking by appraisal professionals whose reports may be reviewed by professional investors and "laypersons" alike. It is my contention that the analysis given in your paper is very thorough, considering the data that was made available to you. But I would not like to be the person responsible for investment decision making without having a feel for the risk involved. Therefore, the reviewer must classify this type of analysis as relatively "subjective" because they have not received an indication of the inherent risk involved in exploiting a mineral resource. This risk can best be quantified by using probabilistic methods in conjunction with the quality and quantity of the mineral to be produced. Most appraisals passively ignore this problem. Specifically, you have accurately identified the various costs and values entering the economic appraisal process. These can usually be quantified with a great deal more certainty than the capability of the resource to provide 25 years of quality material. Also, in Cases A (West Virginia)and B (Alabama), you are fortunate enough to have previous operations data. What if there had never been production from these properties? How does a potential mineral property investor evaluate the resource capability to meet various projected financial outcomes without spending a good deal of up-front capital to drill and delineate enough quality resources for a 20-plus year operation. These questions pose a substantial risk to any potential mineral investor. Only probabilistic methods should be used to quantify this type of problem, short of drilling and metallurgical testing. I might be considered a "layperson," not being familiar

Jan 1, 1991

By J. J. Kellar, W. M. Cross, J. D. Miller

Infrared spectroscopy has been one of the most useful experimental techniques for the analysis of surface reactions in flotation systems, including surface alteration and surfactant adsorption reactions. With the advent of Fourier transform infrared (FTIR) spectrometers, many low-energy throughput IR experimental techniques previously unused by flotation researchers have come into greater use. In particular, internal reflection spectroscopy (IRS) is the most often used technique for in-situ studies. To date, three IRS methods have been used for in-situ measurements. These techniques are evaluated for use in characterization of surface reactions in flotation systems. The method using mineral crystals as reactive internal reflection elements (IRE) is of particular interest because it allows surfactant adsorption densities to be calculated directly from in-situ spectral data in real time. Application of in-situ FTIR/IRS with reactive internal reflection elements will be demonstrated for collector adsorption reactions in each of the major flotation systems. The alumina (A1203)/sodium dodecylsulfate system is used as an example for insoluble oxide/silicate flotation, while the fluorite (CaF2)/oleate system serves as a paradigm for semisoluble salt flotation. For sulfide flotation, sphalerite (ZnS) is used as the reactive IRE with potassium amylxanthate and potassium ethylxanthate as collectors. In the case of soluble salt flotation, sylvite (KC1) is used as the IRE with n-octylamine as collector. Finally, the use of reactive IREs in the near-IR spectral region and in spectroelectrochemical research is discussed.

Jan 1, 1989

By J. A. Finch

The photographic measurement of bubble diameter is tedious and restricted to vessels with transparent walls and relatively low bubble concentrations. A new method for predicting bubble diameter in a flotation column has been developed and confirmed by comparison with measured mean bubble diameter (Yianatos et al., 1987) Flotation columns are not mechanically agitated. This note describes an extension of Ms method to a mechanically agitated flotation machine. A recent publication by Szatkowski (1987) provided sufficient data to calculate bubble diameter by the proposed method and compare with values determined photo- graphically. Method In a two-phase system (gas and liquid), bubble diameter (db), superficial gas rate (Vg) and liquid rate (Vl), and gas holdup (Eg) are linked by two relationships (see the nomenclature at the end of the paper for definitions of symbols). [ ] Equation 1 is the definition of slip velocity (relative gas to liquid velocity) for a countercurrent gas-liquid system, and equation 2 is an adaptation (Yianatos et al., 1987) of the expression of Masliyah (1979) for hindered settling in a multispecies system. The solution for bubble diameter is by repetitive substitution of estimates of db in equation 2 until the calculated Ubs is equal to the measured Ubs in equation 1. Results and discussion Table 1 presents the data obtained by Szatkowski (1987) from a mechanically agitated laboratory flotation machine. The machine generated bubbles by directing a gas stream into the vicinity of a disk rotating at Ngh speed (up to 8000 rpm) in the flotation slurry. The air was completely dispersed in a swarm of fine bubbles. A photographic technique was used to determine the distribution of bubble size. The mean diameter and standard deviation were then calculated. Table 1 provides all the information necessary for computing bubble diameter (Vl is assumed zero). The calculated bubble diameter is presented in Table 1 as d;. Figure 1 plots measured versus calculated bubble diameter and shows reasonable agreement between values. There is an apparent tendency to undercalculate the small bubbles and overcalculate the large ones.

Jan 1, 1987

By C. Douglas Lee

This case study describes the work done at the University of Arizona on the development of a computer mine model for an irregularly shaped and spotty ore deposit. The purpose of the work was to develop techniques for modeling any highly irregular deposit, for which the regular 3D fixed block model is not well suited. The deposit contained complex geology consisting of sedimentary beds that had been faulted, thrusted, and intruded by igneous rocks (see Fig. 1). The physical dimensions of the modeled ore body were 1067 m (3500 ft) along the N-S direction and 914 m (3000 ft) along the E-W direction. Topographic relief in the modeled area was approximately 274 m (900 ft). The highest grade of ore was found near the surface with mineralization extending down to approximately 152 m (500 ft) below. Using a fixed bench height of 12 m (40 ft), the model required 25 levels with the highest elevation being at 1286 m (4220 ft). Fig. 2 shows a cross section of the developed computer model of the ore deposit. The particular modeling approach selected for this deposit was the 3D irregular block model.* This meant that only the dimension of bench height was fixed at 12 m (40 ft). Irregular size blocks in the form of polygons were adopted in the model to describe the ore zones and geologic contacts. The following sections of this chapter describe some of the techniques used in modeling.

Jan 1, 1979