Search Documents

By Raj K. Rajamani, M. K. Abd El-Rehman

The planetary mill is very much suited for the ultra-fine grinding of mineral fillers. Ultra-fine grinding here refers to grinding powders to a size range 5-1 0 rnicrons. Such powders enhance the quality of the final product. The operation of a specially built planetary mill is described. It is shown that a target size of 5 rnicrons can be reached in a few hours using the dual drive planetary mill. A centrifugal field of 37G is generated by the gyration arm of the mill. The design allows the desired setting of canister critical speed. The ultra-fine grinding of alumina, titanium dioxide, hematite, magnetite, kaolin and silicon carbide are described. Also, the continuous operation of the mill is shown.

Jan 1, 2003

By Hong Zhang, Quanming Li, Gang Li

China, a globally recognized major mining country, holds one of the largest quantities of tailings pond country in the world. The total number of mines in China has been ranked first in the world. It is a major concern for Chinese safety management to give great importance for tailings pond safety, stability and sustainable development. For the past few years, China has increased efforts to investigate and govern discrete issues of tailings and to carry out a series of special renovation and comprehensive treatment actions to improve safety management levels and to decrease the likelihood of tailings pond accidents. In the end of 2015, China successfully eliminated hazardous tailings ponds and dangerous tailings ponds. Moreover, the total number of tailings decreased from 12,273 to 8,869. However, there are still 1,425 "head-top" tailings that threaten the lower masses’ safety. This greatly signifies the Chinese tailings pond safety, stability as well as sustainable development. In turn, this may improve the Chinese tailings life cycle safety management system and help reach the goal of attaining closed-loop management in the tailings pond life cycle. Based on the summary of the tailings pond accidents in both China and other countries from 1961 to 2015, and by analyzing the types and causes of accident, this paper investigated the successful experiences and effective measurements of British Columbia (Canada) and Australia in the tailings pond life cycle safety management. This paper summed up each country’s tailings life cycle safety management requirements and analysed the characteristics and differences of tailings safety management by comparing 5 aspects: tailings life cycle safety management process, main design parameter, construction requirements, monitoring, and the tailings pond closing management. Based on these observations, this paper suggests some measurements to improve the tailings pond life cycle safety management in China, such as strengthening tailings pond safety management, improving tailings classification, increasing design parameter values, establishing mine reclamation fund, and so on.

Jan 1, 2017

By S. Becker, M. Gruner

"Microstructure stabilized crushed rock salt is a newly developed backfill material for infrastructural openings in HAW repositories. The motivation for this research is based on the fact that the microstructure stabilized crushed rock salt is considered to be superior to the currently used crushed rock salt. The avoiding of settlements with a simultaneous 100% backfilling of openings, early stabilization of the geological barrier and low permeability (< 10-14 m²) are the main improvements. With the newly developed backfill material, the gap between the crushed rock salt and the saliniferous composite backfill materials is closed. Due to the minimized amount of a binding agent, the material will still be easy to handle like a bulk material, yet guarantees close to 100 % backfill success without any settlements. This is accomplished with a long-term stable re-mineralization that is formed by the components of the binding agent. INTRODUCTION The permanent storage of high active waste in underground geological formations (HAW-repository) is the labored method in Germany as well as internationally. Experiences have been made over the last decades, e.g. in the Waste Isolation Pilot Plant (USA) and the mines Morsleben and Asse (Germany). For this purpose salt formations are preferred as host rock due to the adequate heat conductivity, creep capability, and low permeability. In order to maintain the low permeability of the host rock and to avoid any contact of the stored waste with the biosphere, the formation of flow paths has to be prevented. The cavities which have been mined for the purpose of waste storage have to be backfilled with material that is alike to the host rock. Therefore crushed rock salt is considered as an appropriate backfill material. Crushed rock salt is a bulk material that is produced by mining saliniferous formations. This material is mainly used in underground repositories as a dry backfill that is brought into the cavities by the use of mechanical (loading machine, slinger machine or scraper) or pneumatic energy (pneumatic stowing). In Germany it is intended to use dry crushed rock salt with a maximal grain diameter < 64 mm for backfill in a future repository in saliniferous formations. With this method applied, the porosity of the backfill is up to 35 % [1]."

Jan 1, 2015

By J. W. Hawkins

Understanding aquifer properties in surface mine backfill is essential for managing the groundwater flow system as well as controlling the formation and discharge of acid urine drainage. Slug tests (injection and withdrawal) performed on wells in mine spoil may yield two distinctly different response characteristics. One type of response is indicative of a porous media system. The second type of response indicates the presence of a pseudokarst system. The presence of voids or conduits in the backfill is indicated by an almost instantaneous partial recovery of the water level displacement. This rapid recovery is turbulent flow and cannot be analyzed by conventional (Darcian) methods. The turbulent flow may cause the calculated hydraulic conductivity to be less than the actual values. The slug dissipation surface area created by the voids contiguous to the test well add to the known dissipation surface area of the screened interval. This can cause the calculated hydraulic conductivity to be greater than the actual hydraulic conductivity or the aquifer to appear more permeable. Whenever analyzing data from aquifer tests in mine spoil, these potential problems must be kept in mind. In spite of the problems encountered during slug testing of spoil, the aquifer hydraulic parameters derived and the slug responses observed remain useful in the hydrologic characterization of a mine site.

Jan 1, 1994

By Richard Hogg, Erol Kaya, Jan M. Mutmansky

Characterization of the size, shape, chemical composition, and mineralogical content of mine airborne dusts generally requires a larger mass of dust particles than is typically collected using traditional sampling devices. In this paper, the general design of a passive dust collector is described and the field results are presented. The collector was constructed of galvanized sheet metal duct with a resin-coated honeycomb to provide an elutriation-type system for particle collection. Several versions of the collector were used in the field portions of the research. The dust samples collected from underground coal mines were found to possess angular particle shapes, relatively consistent size distributions, and elemental compositions that showed relatively little variation, at least for the more prevalent elements. In addition, the distributions of particles sizes obtained from the passive dust collector appear to be similar to those of samples collected at the same time in a conventional personal sampler except that the passive device seems to collect a larger quantity of coarse, non- respirable particles. Conclusions on the suitability of this dust collector for collecting characterization samples are presented. In addition, the potential for using such a dust collection system for supplying dusts for biomedical research is discussed.

Jan 1, 1993

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, BRADLEY BENNETT, Patrick Zhang

The purpose of this work is to develop a conceptual recovery process for thorium dioxide (ThO2) from its primary source, monazite. The study-level design presented in this paper represents an economically viable method for conducting ThO2 extraction from monazite ore while also recovering byproducts that include P2O5 and other rare earth element oxides rather than producing unnecessary waste streams. Three key points to note in the development of this process design are: (1) the process economics relied heavily on recovery of rare earth byproducts, (2) the thorium handling portions of the process could effectively be segregated from the rare earth and phosphate handling portions of the process, and (3) the thorium and uranium content in waste streams should be carefully managed and eliminated where possible.

By H. Wu, V. Izaxon

Intensive ventilation is required during the excavation of a mine opening and the subsequent exploitation of the mineral resources. The exchange of heat between the ventilation air and the rock mass has a major influence on the thermal regime of a mine, especially in the initial segment of the airway. In frozen ground, heat flow into the rock mass from the ventilation air can result in the eventual thawing of the permafrost, which can result in roof-rock instability. This paper presents a mathematical analysis of the dispersion process of ventilation-induced heat by thermosyphons placed on the surface of the mine. The principal uses of thermosyphons in the Arctic are to reduce the ground temperature to prevent potentially unstable permafrost from thawing and to increase the bearing strength of the material. The mathematical model of the physical problem, generally known as "the Stephan problem," takes into account the varying thermo-physical properties of air and the frozen and thawed rock mass, the thermal properties of the freeing fluid in the thermosyphons and the phase change of water. Finite-difference techniques were employed to determine the temperature isotherms around the thermosyphons. It was found that two rows of thermosyphons on a 10- x 10-m grid provide an acceptable design spacing for reducing the ground temperature around the mine airway.

Jan 1, 1997

By D. H. Carlson, J. H. Johnson, C. F. Renders

Research was conducted at a western coal mine on a wide variety of underground mining vehicles to develop testing procedures for portable instrumentation monitoring of tailpipe concentrations of diesel particulate matter (DPM), carbon dioxide (CO2) carbon monoxide (CO) and nitric oxide (NO). DPM was measured using the Emissions Measurement Appa¬ratus (EMA) developed by Michigan Technological University (MTU), and an ECOM-KL five-gas analyzer was used to measure gaseous tailpipe concentrations. Baseline concentrations of the tailpipe pollutants were measured using vehicle systems to load the engine. Concentrations before and after the water scrubber were measured and water scrubber efficiencies were estimated by calculation. Field measurement procedures were established. Heavy-duty vehicles with automatic transmissions were loaded using the torque converter to stall the engine. Consistent engine loading for light-duty vehicles with manual transmissions involved placing the transmission in neutral and adjusting the throttle to maintain a constant engine speed of 2,500 rpm. Tailpipe CO2 concentrations for Caterpillar 3306 and 3304 engines were compared to laboratory CO2 data from Caterpillar and MSHA to help determine if engine settings were correctly adjusted for operation at high altitudes. (Perfect agreement between the mine vehicle tailpipe and laboratory measurements would not be expected because of the differences in the test conditions.) DPM concentrations for light-duty vehicles ranged from about 20 to 160 mg/m3, and one light-duty vehicle averaged near 1,000 mg/m3. DPM concentrations for heavy-duty vehicles ranged from about 55 to 200 mg/m3. Widely ranging DPM concentrations for a particular vehicle type reflect the state of maintenance, fuel rate settings and different engine loading procedures as well as differences between samples collected upstream and downstream of the waterscrubber. The calculated DPM removal efficiencies due to the water scrubber varied considerably between vehicles, ranging from 13% to 51%. Calculations indicate that, under worst-case conditions, very large reductions in DPM may be required to meet the proposed DPM PEL of 0.15 mg/m3, even on vehicles with water scrubbers. In-mine ambient air studies, which are needed to actually measure the impact of the tailpipe concentrations on the work environment and the effect of mine ventilation on the dilution of DPM were not done in this first set of tests.

Jan 1, 2000

By J. F. Rakszawski, Robert P. D'Orazio

The use of cyanide in the processing of gold has been documented for over a century. It is still one of the more effective methods of isolating gold, as witnessed by the fact that in 1987 cyanidation was used in the processing of 91.5% of the gold produced in the United States.

Jan 1, 1990

By N. D. Jagger

In order to maximize the benefits obtained from flocculating agents when used as settling aids in high rate and conventional thickeners, it is often necessary to dilute the thickener feed prior to flocculant addition. In some cases, no flocculation at all is possible unless dilution water is used. The most common method of diluting thickener feed has been to recirculate some of the thickener overflow by means of a centrifugal pumping system. This represents a significant capital and operating cost. Supaflo Technologies of Australia has developed and patented an internal recirculation method known as Auto Dilution (or "Autodil") which is based on the principle that an hydraulic head differential exists between the inside and outside of the feedwell because of the higher S. G. of the pulp inside the feedwell, By installing non-return ports in the feedwell wall at the appropriate level, supernatant solution flows into the feedwell at a calculated rate and dilutes the feed without any need for external recirculation of overflow.

Jan 1, 1993

By P. Berendsen

Structures along the rift were subjected to episodic reactivation. Major north-northeast-trending high-angle normal or reverse faults and northwest-trending trans-current fault systems, may exercise control over ore-forming processes. Gabbro and basalt are the dominant igneous rock types. Carbonatite and kimberlite occur in Nebraska and Kansas. Concentrations of Cu, Ni, Co, Ti, Au, Ag and PG-minerals are known to occur in this setting Arkosic sandstone, siltstone, shale and minor carbonate units occur on top of the rift basalts and in flanking basins where they may reach thicknesses of 10 km. The potential for stratiform or unconformity-related metal liferous deposits must be considered.

Jan 1, 1986

By D. G. Mirakovski, B. Krstev

The paper presents models of auxiliary ventilation systems with leaky ducts and algorithms for calculations of pressure loss, air leakage, and volume flow ratio and pressure fans. Two basic models are discussed: 1st model for a duct with leakage through the flange joints; 2nd model for a duct with an equivalent longitudinal aperture. The present analytical system has been successfully applied to developing of computer software named DAVentS. A. sample problem is used to illustrate efficiency and accuracy of DAVents software in solving most common problems in process of designing AVS.

Jan 1, 2002

By J. A. Finch, G. Labonté

The behavior of four different redox sensing electrodes (gold spiral, black platinum, chalcopyrite, and galena) during roughing and cleaning flotation is examined and related to the flotation response. The results indicate that the solution potential (as sensed by the black platinum electrode) is different from that of the pulp potential (gold spiral) and is only weakly related to the flotation response. On the other hand, the potentials exhibited by the gold spiral and the two mineral electrodes are related to the flotation response. The transient responses of the gold and mineral electrodes during the addition of flotation modifiers could indicate the conditioning time required to achieve flotation or depression of selected minerals.

Jan 1, 1991

By Lynn B. Hales, Randy A. Ynchausti

Object-oriented technologies have been developed to more closely model the way we think about the world and our natural approach to solving problems. Higher levels of abstraction, generalization and classification are benefits of an object-oriented approach. Object-oriented programming, design, and expert systems are part of this technology which is shaping the future of real-time supervisory control. Goals of real-time supervisory control systems include: minimizing variations in process operations, improving efficiency, maximizing production, and implementing procedures for starting and stopping the process. Incorporating object-oriented technology in design, development and implementation of real-time supervisory control systems provides new opportunities for these tasks. This paper discusses some of the opportunities and challenges of implementing real- time supervisory control using an object-oriented expert system for a rougher flotation circuit

Jan 1, 1993

By L. A. Morley, S. C. Gambrell

Behavior of a jour-leg shield design used on a soft floor in an operating longwall system is presented. The shield examined in this study was constructed having a split base and a split caving shield. Attention is focused on other-than-normal loading on the canopy and its effect on deformation of the lemniscate links. Examples of the magnitudes of typical bending and twisting deformations are given. Schematics of the canopy, caving shield, and lemniscates showing important forces and moments are presented. Approximate minimum values of the forces and moments required to produce the deformations are calculated based on the mechanical properties of the material. The need for use of more inclusive three-dimensional design techniques is demonstrated.

Jan 1, 1991

By Selamet G. Ercelebi, Mahmut Yavuz

An inherent aspect of longwall mining is moving the equipment from a mined-out panel to a newly developed panel. Moving times may be reduced by detailed preplanning. A very useful tool for planning is MS Project. Using MS Project, one can efficiently plan, manage and coordinate a project from conception to conclusion. The critical path analysis identifies potential critical activities which may cause excessive time delays. Changes to the tasks on the critical path can have significant impact 0.n the completion of a project. Assigning additional resources to these tasks (either moving labor from other tasks to critical tasks or providing labor overtime work) may reduce the move time. Simultaneous activities are the candidates for moving the labor from an activity to another. Each time a change is made, the critical path should be recalculated. MS Project quickly recalculates schedules and lets you see how changes in one part of the project will affect the overall plan. In this fashion it is possible to minimize the longwall move time.

Jan 1, 2002

By S. L. Huang, J. D. Rockaway, N. B. Aughenbaugh

Shale has long been recognized for its tendency to swell when exposed to the atmosphere. Interaction of moisture with exposed shale strata can cause serious ground stabi1ity problems, since the initial strength of a shale is reduced if the material is sensitive to moisture variations. In this paper, the authors present a classification system to estimate the response of swelling generated within shales. This characterization of the swelling potential is based upon plasticity, susceptibility to moisture, mineralogical constituents of clay size particles, and fabric. Use of this classification system in conjunction with other existing rock properties tests will provide data for more rational engineering design.

Jan 1, 1986

By E. G. Kelly

Many methods of evaluating the efficiency of mineral separations have been described in the literature. In most cases, these present the efficiency as a single number. This paper argues that single-number measures of efficiency are inadequate because they seldom allow reliable comparisons, and are unlikely to correspond to the optimum operating conditions. To realistically make comparisons, it is necessary to distinguish the particle-induced component from the equipment- induced component. In a number of situations where the separating property can be identified (such as in gravity concentration and classification), this can often be done. However, in more complicated systems, such as flotation, this has not been possible. A technique is described whereby particle and equipment contributions to efficiency can be distinguished without the need to define the separation property. Because smelter schedules define a boundary correlation between grade and recovery, they generate some of the better single¬-number measures of efficiency, but even these have limitations.

Jan 1, 1991

By A. D. Davis, C. J. Webb

Brohm Mining Company&apos;s Gilt Edge Mine in the northern Black Hills was a surface heap-leach operation that was active from the 1980s until 1999. Financing problems and acid drainage concerns at the mine were reported in the late 1990s. In February of 1999 the Governor of South Dakota announced plans to request the U.S. Environmental Protection Agency to help clean up acidic water at the mine and reclaim the site. In July 1999 the parent company of Brohm, Dakota Mining, filed for bankruptcy in Canada. Because of the bankruptcy and environmental problems, the State of South Dakota intervened and began water treatment. The mine was declared a Superfund site in 2000. Hydrologic issues include the potential for acidic drainage from the site. The mine is at the headwaters of Strawberry Creek, which drains into Bear Butte Creek. About four miles downstream, Bear Butte Creek loses its discharge to swallow holes in the karstic Madison Limestone aquifer, a regionally extensive and valuable ground-water reservoir. Other concerns at the site include treatment of acidic water in mine pits and a waste rock dump.

Jan 1, 2002

By D. Koren, D. Carson

Disposal of smelter slag may be subjected to regulatory leach tests to deter- mine whether they produce a leachate containing contaminants in excess of stated limits. Contaminants that are most often of concern for smelter slags are As, Cd, Cr, Cu, Ni, Pb, and Zn. The present regulatory tests are based on the assumption of storage in a municipal landfill dump, where wastes are in contact with organic acids. Since slags are not normally stored in such an environment, these tests do not adequately assess the true leachability potential of the slags. Ten slags from six major Canadian nonferrous sulfide smelters were studied. Leaching was done following regulatory and modified tests, including leaching in columns with synthetic acid rain for a 25-week period. The slags were characterized by mineralogical analysis before and after leaching with synthetic rain. The synthetic mineral equivalents (hereafter referred simply as phases) in the slow cooled slags consist of fayalite grains and dendrites, amorphous glass, some spinel and small quantities of complex sulfidic prills and metallics. The phases in the quenched slags consist of amorphous glass, some spinel and small quantities of complex sulfidic prills and metallics. Some metal dissolution took place during leaching. However, for all leaching tests, the concentrations were always below the regulated limits. In general, the content of the potentially leachable elements remains unchanged in the fayalite, in the amorphous glass and in the spinel, whereas the quantity of sulfidic prill and metallics decreases after leaching. Therefore, most of the deleterious element dissolution comes from the sulfidic prills and metallic phases. Metal dissolution increases by crushing the slag, probably due to an increased exposure of the sulfidic prills to the leaching solutions.

Jan 1, 1998