Search Documents

By Aladar B. Dory

INTRODUCTION Practical experience in mines with known presence of radon daughters in the mine atmosphere in Canada and elsewhere shows that a very high concentration builds up in an unventilated dead end heading. As Holaday et al1 observed, even a minimal air movement results in a drastic reduction in radon daughter concentration. It is therefore obvious that the main objective of radon daughter control in the working environment is to design the ventilation system providing an optimized flow of fresh air into the workplace, resulting in acceptable climatic conditions and achieving radon daughter concentrations resulting in exposures as low as reasonably achievable. BASIC OBJECTIVES Large mining companies, having extensive material resources and professional expertise, have utilized elaborate electrical modelling in the design of mine ventilation systems as early as 1950 (coal mining industry in Europe) and with the advance of computer modelling techniques, their utilization in ventilation systems design is on the increase. Unfortunately, these methods are usually not available to small mining companies and even the large companies might not achieve the fullest benefit from utilizing them, if proper limiting factors are not considered in the modelling. When an evaluation of a ventilation system of a mine is undertaken in literature, a measure of the amount of air supplied underground per one ton of ore mined is used as an indicator of the efficiency of the ventilation system. Yet, even the greatest amount of air forced into the mine might not result in an acceptable working environment if a proper distribution of this air into individual working places is not achieved. The volume and the age of the air are probably the two most important factors in achieving acceptable radon daughter concentrations in the workplace, but other factors also have to be considered. DIRECTOR MINE - ALCAN, NEWFOUNDLAND FLUORSPAR WORKS ST. LAWRENCE, NEWFOUNDLAND, CANADA Ventilation To illustrate the effects of the design of the ventilation system on the control of radon daughter concentration, let us review the gradual development of the ventilation system of this mine from the earlier years of its development up until its final years of operation. This mine, located near the community of St. Lawrence on the south coast of Burin Peninsula was developed in the late thirties and reached full production by 1942. Unfortunately as was customary at that time, the only source of ventilation was a natural draft. The mine was extremely wet, and no significant attention was initially given to possible health effects of dust. It was not until the mid-fifties, when a number of cases of silicosis had surfaced, that de Villiers and Windish2 observed a significant increase of lung cancer incidence among the miners in comparison to its incidence among the general population of Newfoundland. Suspicions regarding radiation as a cause of the lung cancer were expressed, but it was only in surveys taken in late 1959 and early 1960 that Windish3 and Little4 established the presence of radon daughters in the mine atmosphere in very high concentrations. Windish, de Villiers and Hurley suggested that the most likely source of the radon in the mine was the mine water which dissolved radon during its passage through the granitic country rock in the surrounding geological area. This conclusion was confirmed by analyses of water from various areas of the mine by the Atomic Energy Canada Limited laboratories. The radon values in the samples varied from 4,240 to 12,850 pCi/L5. Following the discovery of the presence of radon daughters in the mine, the company took speedy action to install mechanical ventilation for the mine. The system was not designed as a total unit, but fans were installed rather on a trial and error basis. The basic system installation began in March 1960 and was completed by 1962. It remained basically unchanged with only minor modifications until August 1973 when a wholly new, redesigned ventilation system was implemented. A schematic section of the mine and its ventilation system for the period prior to March 1960 is given in Figure "A", for the period 1960-1973 in Figure "B", and for the period after August 1973 in Figure "C". The ventilation system prior to 1960 is not known. All workings of the mine were ventilated only by natural ventilation. If any measurements of airflows at different or any times of the year ever existed, no records have been preserved. The very minimal natural ventilation was augmented by "blowing" air from compressed air supply lines and exhaust air from drills. It is known that the compressor capacities of the mine were limited and therefore no significant air movement was probably created by the "blowing".

Jan 1, 1981

By Nenad Spoljaric

Greensand, greensand marl, and green earth are names given to sediments rich in the bluish green to greenish black mineral known as glauconite. The word glauconite is derived from the Greek word glaukos, meaning bluish green. The term "greensand" as a rock name for a glauconite-bearing sediment is more appropriate than "greensand marl," a term that has been doggedly perpetuated in the literature. Because of its potash and phosphate content, greensand was mined and marketed as a natural fertilizer and soil conditioner for more than 100 years. The advent of manufactured fertilizers with adjustable nutrient ratios led to a decline in the use of greensand in agriculture. The material has since been recognized as useful in water treatment. Unfortunately, despite large reserves and world- wide distribution, glauconite has not been utilized to any significant commercial extent because no major application has been found for a substance with its chemical composition and properties. This is probably due mostly to a paucity of research on its potential commercial uses. Extraction of potash received considerable attention during and just after World War I. Because of relatively high extraction costs and a generally low potash content (viz., less than 8%), glauconite lost its appeal as a source of this commodity. Historical Background Greensand was used as a fertilizer in New Jersey in the latter part of the 1700s. During the early 1800s its use became more common; applications of as much as 22.5 kg/m2 were sometimes made, although recommendations for agricultural use suggested 4.5 to 11 kg/m2 (Tedrow, 1957). Many crops, especially the forage type, were said to improve with greensand application; however, because of its slow release of potash, large quantities were required. Certain greensands that contain sulfur and sulfide minerals are harmful to plant growth, and these were classified as poison, burning, or black marls. The availability of higher grade potash salts from other mineral sources and the manufacture of prepared fertilizers displaced the agricultural use of greensand during the latter 1800s. During the mid-1800s the greensand industry, centered in a small section of the eastern United States, grossed more than $500,000/y. Toward the end of the century, however, annual production had dwindled to less than $100,000 in value. By 19 10 there were only six or eight greensand producers grossing less than $5,000/y each (Tyler, 1934). There was a brief revival of the US industry during World War I because of the curtailment of foreign potash, especially from Germany. During the latter 1940s and early 1950s greensand was again recommended as a food nutrient for plants and farm crops. Agronomic studies discussed its potential as a soil additive that gradually releases potash and many trace element nutrients essential for plant growth (Tedrow, 1957). Greensand was sold with the idea that it would condition soil and absorb and hold water while its base exchange properties would release trace elements. For a short time glauconite was used in certain parts of New Jersey as a binding additive in the brick industry, and in the 1800s it was used for making green glass (Cook, 1868). In the early 1900s the base exchange properties of glauconite were recognized for water treatment and the mineral gained acceptance as a water softener. Mansfield (1922) does not mention base exchange even though this phenomenon was known in 1916 or earlier. From 1916 through 1922 several patents for the use of glauconite as a water softening agent were granted. A method was also patented for treating greensand to improve it for water softening and ready regeneration with common sodium chloride brine (Borrowman, 1920, Spencer, 1924, Kriegsheim and Vaughan, 1930). Treated glauconite, on contact with water containing magnesia or lime, takes up magnesium or calcium ions and releases sodium ions. This exchange is limited to the outer surface of glauconite grains, and when all the surfaces have absorbed their capacity, the grains must be regenerated. Regeneration, simply stated, consists of treating or backwashing the glauconite with a sodium chloride solution, which replaces the hard water elements with sodium, thus reviving the glauconite. The process has become more sophisticated due to competition among companies in the water softening business. Greensand products for water softening generally consisted of several different grades distinguished by the particular treatment the glauconite was given during processing. The standard greensand water softener was produced from natural glauconite that was only washed and classified. Its characteristics for water softening are given in [Table 1].

Jan 1, 1994

By R. P. Upadhyay

The Deserado Mine, located in northwest Colorado, is an underground coal mine designed to produce 1.225 million tons (1.35 million short tons) of clean coal per year for the Bonanza Plant located in northeastern Utah. Coal is transported to the power plant via a 61 kilometer (38 mile) captive railroad. Most of the surface facilities and the stationary underground equipment is controlled and continuously monitored by the computers located at the surface control room. In addition to system control, the computer also continuously monitors vital environmental conditions using sensors located at various critical locations underground. The system's advantages are increased mine productivity and safety.

Jan 1, 1988

By J. E. Oberholtzer, M. G. Fernald

INTRODUCTION Approximately six years ago the U.S. Bureau of Mines (USBM) developed a data acquisition system (DAS) specifically designed for measuring radon levels and other environmental parameters during studies of means to control radiation hazards in underground uranium mines. The DAS system records data in machine readable form using a paper tape punch, which represented the state-of-the-art at that time for a moderate cost output device. However, the use of paper tape as a recording medium for field studies is somewhat unwieldy. Reducing the raw data required either that the tape be shipped to a computer center equipped with a high-speed paper tape reader or that the tape be transmitted at low speed over the telephone lines to a remote computer. Transmitting, at ten characters per second, the data from a 10-channel DAS taking Four readings per hour would require about 30 minutes For each 24-hour day's data. Telephone lines from remote mine sites are often of marginal quality and data errors can be introduced during transmission. Paper tape punches are also prone to occasional punching errors. Both problems make it necessary to carefully check for and correct data errors, a process which is possible because each DAS produces an independent printed data record, but the error checking and correction process can be quite laborious. Aware of recent advances in microcomputer technology which have brought the price of a personal computer down to about the cost of a paper tape punch 5-10 years ago, the Bureau decided to explore the feasibility of using a low-cost personal computer in the field to process DAS data in real time. On behalf of the Bureau, Arthur D. Little, Inc., developed a simple interface circuit which permits an Apple II computer to accept data from one or two DAS units as it is being transmitted to the paper tape punches. Computer software converts each measurement to appropriate engineering units, e.g., radon concentration, Working Levels, air velocity, temperature, or barometric pressure. The computer also calculates 1-hour and 8-hour running averages of all converted data and prints those results as soon as they are obtained on a line printer located at the test site for immediate inspection. After development, the system was used continuously and successfully for a 5-month period at a Utah uranium mine. DAS DESIGN AND MODIFICATION Each of the two USBM data acquisition systems used in this work consists of two separate modules. A multiplexer module located below ground near the measurement transducers acquires signals from each of nine tranducers. Six input channels were devoted to measurements of radon or Working Level. The outputs of those transducers, photomultiplier tubes or G-M tubes, respectively, are digital pulse trains which are accepted directly by the mutliplexer. Three channels were used for environmental parameters--air velocity, temperature, and/or barometric pressure. Each of the environmental tranducers is fitted with dedicated linearizing and voltage-to-frequency conversion circuitry so that the outputs to the multiplexer are also pulse trains having frequencies of one tenth of the value of the measured parameter expressed in the appropriate engineering units. A 100-Hz reference signal was input into the tenth channel for use in monitoring system integrity and performance. All ten pulse trains are then timeseries multiplexed into a signal line for transmission to the above-ground data acquisition module. Above ground, the composite signal is de-multiplexed into ten separate lines, each of which is connected to a digital counter which converts the pulse train to a numerical value. The acquisition of each set of readings is initiated by an adjustable "scan cycle comparator" timer. The acquisition process proceeds in three phases. First, radon and Working Level channels are counted for an extended period of time, typically 5-10 minutes depending on activity, because of the low pulse rates involved. Then the other four channels are counted for ten seconds, and finally, all ten readings, along with the Julian day and time of day are output serially onto paper tape and printed on a strip printer. When the scan cycle comparator reaches its preset time (15-minute cycle times were used in this work), it resets itself, initiates another readout cycle, and begins timing again. The only modification made to the data acquisition systems used in this work was to disconnect the scan cycle comparator in one unit, which became the "slave" and bring in the scan cycle comparator signal from the other unit, the "master", to initiate data acquisition cycles in the slave. Synchronizing the two data acquisitions in this fashion and using two slightly different radon counting times insured that the two systems never attempted to output data to the Apple II at the same time. THE APPLE II COMPUTER The Apple II computer used in this work was equipped with 48 KBytes of semiconductor random access memory (RAM), two floppy diskette drives, a Centronics Model 730 impact matrix printer and a modulator for driving an ordinary color television as a video display device. A single California Computer Systems Model 7720A dual 8-bit bidirectional parallel input/output (I/O) card was installed in the Apple to accept the digital data from both data acquisition systems. This card is

Jan 1, 1981

By A. M. Edwards

In many ways a government could be regarded as a macro business enterprise. Its shareholders are its peoples, the productivity of the nation depends on them, and, indeed, the profits or losses of a nation's balance sheet can be linked to the surplus or deficit in its balance of payments. International loans need to be repaid, and in most developing nations the noose is tied so tightly that one wonders if such debts will ever be repaid. In their endeavour to meet such obligations, their currencies may be devalued [sometimes in frightening proportions], in the hope of boosting the export potential. However, this is a vicious circle, since exports will not be achievable unless sufficient technical expertise and infrastructure exist to address the opportunities which may have been created through devaluation. Many of the poorer countries have exportable resources of minerals, which are supplied on the international market. This may be the good news, but, unhappily, steps were seldom taken to enhance the value of the mineral products through further beneficiation and the production of high-value sophisticated products. That is where the vicious circle comes in: inadequate infrastructure is created, competent and well-trained manpower is not generated, and the result has inevitably been that the GDP slips backwards, and the nation becomes progressively impoverished. To exacerbate the problem, it is unfortunate that the more impoverished a nation becomes, the greater is its birthrate, and hence the greater the need to create wealth at the very time that the nation is becoming poorer and poorer. Within this scenario, one may well reflect that this is exactly what nations on the African Continent are experiencing, namely exploding populations, although most of the poorest nations in the world are found on this continent. Yet they often possess a superior mineral production potential. Africa still suffers from what may be called the colonial influence, in that the developed world has regarded this continent as a source of raw materials to feed its own factories. The colonial powers gave only secondary attention to developing the nation's peoples and its infrastructure, such as railways, roads, harbours, and other services. These problems all naturally fall within the ambit of government interest, and it is therefore obvious that the state should play a dominant role in addressing them. The reasons for governmental involvement in mineral-related research and development differ considerably, depending on the state of industrial development of that country. Thus, in the highly industrialised world, government's interest will lie mostly in the fields of strategic minerals, which may not be economically exploitable. An example would be the exploitation of American low-grade chromites during the Second World War, or minerals which need to be imported from unfriendly or unreliable sources, such that disruption would not be in the national interest. Colonial powers like the United Kingdom and France established R&D facilities to assist, inter alia, in the exploitation of mineral resources in their colonies. The approach of developing countries would differ from that of the industrialised nations, in that their primary quest would be to promote, support and encourage the development of infrastructure, and the establishment of major industries in order to create and provide employment opportunities, as well as to support small operators who cannot afford to undertake their own research and development. On the debit side, it is a sad fact that, however good their intentions may be, underdeveloped countries are invariably unable to provide the requisite financial support to sustain their own research-and-development laboratories. In a high-tech world, the cost of sophisticated equipment is steep and cannot be afforded. Again, the proverbial vicious circle comes into play. The competent researchers find themselves without rewarding employment and would therefore shun such institutions. Recent trends in the developed world have been to privatise research-and-development institutions, the argument being that they should draw closer to the industry they serve, and that the provision of taxpayers' money for strategic purposes is no longer as important as it may have been once. Complete state withdrawal has had its negative effect in that long-range, high-calibre research has tended to be replaced by short-term problem-solving projects. Industries engaged in the minerals business differ somewhat from major ones, like motor, computer or pharmaceutical industries, which are large enough to support their own internal research and development, and whose work is highly confidential, so that any leakage could have disastrous consequences. Furthermore, private companies are answerable to their shareholders and costly long-range, 'blue-sky' research would be difficult to justify. Since mineral research has become of lesser importance in the sophisticated First World, this trend has persisted. On the positive side, R&D institutions which are totally financed by government, suffer because they tend to forget the reason for their existence. They have often become a form of auxiliary to an academic institution where higher degrees are collected by scientific boffins who, in their quest for academic excellence, tend to disregard the benefits that industry may ultimately gain from this research endeavour. The trend in recent years - and South Africa is no exception - has been for the state to progressively reduce its subsidy, whilst at the same time encouraging research organisations [for their ongoing survival] to interact closely with industry, and to conduct work directly for them on a contract basis. Organisations such as CSIRO in Australia, CANMET in Canada, the USBM in the United States and Mintek in South Africa all generate income from the private sector. However, the critical fact is that the State should never withdraw

Jan 1, 1995

By L. P. Meade

The particular impact of imported industrial minerals varies within the Industry and is dependent upon many diverse factors. In a similar way, the impact on individuals has been varied and the degree of impact will depend partially on the individual's ability to handle change. Just as many corporations are adjusting their marketing strategy and production methods to compensate for imported mineral products; individual managers, mining engineers and geologists are making adjustments to their own personal job marketing techniques and on-the-job operating procedures. Modifying the degree of impact for both industry and individuals depends upon the ability to adapt.

Jan 1, 1988

By B. C. Lewis

When John F. Kennedy made this statement, I am sure he was not thinking about the valuation of limestone reserves. However, it is certainly applicable. The objective of this paper is to demonstrate how the discomfort of thought (i.e., the analytical and methodical process performed by a reputable professional) builds the foundation for an opinion that provides assurance as to the value of a property. In its final form, a valuation is nothing more than an opinion. The credence of that opinion is directly proportional to the knowledge of the appraiser and the efforts and judgment extended in developing said opinion. Presented herein are the methodologies for formulating a defensible opinion. Before detailing the valuation process, an overview of the limestone industry is presented along with some historical parameters relating to the industry. Secondly, the most widely used valuation methodologies and a brief discussion of each are presented. Two case studies are then presented, which review actual valuation studies. The paper concludes with how the valuation process should be published in a report format that is defensible from a legal standpoint, bankable from a financial standpoint, and decipherable from a layman's standpoint.

Jan 1, 1989

By H. Wagner

INTRODUCTION One of the most important tasks facing the opera¬tors of deep-level gold mines is supporting the roof strata in the immediate vicinity of the stope faces. Some of the deeper gold mines operate at depths ex¬ceeding 3.0 km; the extreme mining depths and the tabular nature of the gold-bearing reefs result in high stress concentrations at the abutments of the stope faces. These, in turn, lead to extensive fracturing of even the hardest quartzites. Although most of these fractures develop in a stable manner, there have been many instances where rock failure occurred suddenly, resulting in a considerable amount of damage to the underground workings. Such violent rock failures commonly are known as "rock bursts," and they are typical of many hard-rock mines that are operating at great depths. To safeguard mining personnel and equipment against the effects of stable and unstable rock failures, adequate support must be provided to the fractured roof as quickly and as effec¬tively as possible. Traditionally, timber props and timber packs have been utilized to provide roof support in gold mine stopes up to 1.5 m wide. Both methods of support suffer from the fundamental disadvantage of generating sup¬port only in reaction to movement of the strata. Since unrestrained strata movement often results in a break¬down of the frictional forces that preserve the stability of the intensely fractured roof strata, it is essential that stope supports have rapid load-bearing characteristics. An equally important requirement is that the roof sup¬ports be able to accommodate displacements of the rock mass. A third requirement of roof supports in gold mine stopes is that they must be able to accommodate the high rates of stope convergence typical of rock bursts. The hydraulic prop is the obvious choice for sup¬porting the stope faces in deep-level hard-rock mines. Since hydraulic props can be installed with a positive setting load, they can provide roof support that is independent of strata movement. By equipping the hydraulic props with yield valves, they meet the require¬ment of being able to accommodate rock-mass displace¬ments. However, the requirement of being able to accommodate high rates of stope convergence without overloading or damaging the rock strata was rather difficult to meet. The first introduction of hydraulic roof supports into gold mine stopes showed that conventional hy¬draulic props, such as those used in coal mines, were completely unsuitable for a number of reasons, in¬cluding: 1) Since drilling and blasting are used to break the ore in gold mine stopes, supports installed close enough to be effective are exposed to the vigor of the blast. Conventional coal-mining props suffered extensive blast damage, despite being protected by a blast barricade. 2) The environmental conditions in gold mine stopes favor corrosion. The high quartz content and the abrasiveness of the ore further aggravate the problem by damaging the protective coatings on the hydraulic surfaces. Simply changing the design of gold mine props to have the piston project from the bottom rather than from the top resulted in dramatic improvements in the service life of the props. The improvement was attributable to external water in the stope washing the fine quartz grit away from the hydraulic surfaces, rather than concentrating the particles between the cylinder and piston of the prop. 3) The most obvious deficiency of conventional coal mining props was their inability to yield rapidly enough to accommodate the high convergence rates of rock bursts without overloading the supports. As a result of the first disappointing results with hydraulic supports in narrow hard-rock stopes mined by drilling and blasting, a comprehensive research and development program was undertaken. The hydraulic props resulting from several years of research and exten¬sive field trials are described herein. To date (1978), more than 130,000 of these props have been manufac¬tured and used successfully in a number of mines and under a variety of geological conditions. Although many of the detailed specifications are directed spe¬cifically to gold mining conditions, there are a number of points that are of general importance in the design of underground support systems for tabular excavations in hard-rock mines of any type. SPECIFICATIONS FOR RAPID-YIELDING PROPS Yield Requirements The yield requirements for hydraulic props in deep¬level hard-rock gold mines are summarized in the fol¬lowing paragraphs. Slow Yield Load: The design of the yield valve must allow the yield load to be preset to between 300 and 400 kN. This flexibility is necessary to account for the differences in the strength properties of the roof and floor strata. Drop in Load Under Slow Yield: The drop in sup¬port load during a slow yield should be as small as possible, but it should not exceed 5% of the slow-yield load. Rapid-Yield Load: The load exerted by the prop during periods of rapid stope convergence should be as close as possible to the slow-yield load. The rapid-yield load should not exceed the slow-yield load by more than 15% at yield rates of 1.0 m/s. The limitation of the upper valve of the yield load is important; it deter¬mines the hydraulic performance of the yield valve. The hydraulic props that satisfy this criterion have performed well, even under severe rock bursts. Load Changes Under Rapid Load: On some of the earlier rapid-yielding props, conditions of dynamic in¬stability were observed; these conditions resulted in a complete breakdown of support resistance. It is essen¬tial that the force oscillations during rapid yielding be as small as possible, not exceeding -*5% of the average rapid-yield load at a yield rate of 1.0 m/s. Longitudinal Resilience: During rock bursts, vibra¬tions of the roof and floor sometimes are observed. To

Jan 1, 1982

By Wallace Jarman

Introduction As with many gravity concentration processes, pneumatic concen¬tration traces its origin in antiquity. The use of winnowing to separate chaff from grain has long been known, and such procedures were undoubtedly practiced in ancient civilizations for the concentration of ores and the separation of slag from metal whenever specific gravity, size, and shape differences were favorable. Taggart142 has reported on the use of dry rockers and dry panning techniques for use with gold ores in arid regions such as Western Australia. The present day air table was developed in the last century for this purpose. Devices and Processes Classification. All classifiers make a separation on the basis of size, shape, and specific gravity. In addition to specific gravity and size, particle shape factor is often particularly important to pneumatic processes, and advantage is taken of the fact that both flat and fibrous particles settle at velocities substantially lower than that of their equiv¬alent spheres. Another factor of importance in this process is the bulk density of the material since substances such as exfoliated ver¬miculite or partially opened fibrils of asbestos have bulk densities significantly lower than those of the pure in situ mineral. Winnowing takes advantage of all of these physical factors to affect a separation starting with a closely sized feed, and vermiculite has been separated from rock by this process.142 When air classifiers are used to size minerals, the separation will often not be perfect because heavy particles will respond similarly to somewhat coarser light particles while flat, elongated, and low bulk density particles will act as would particles finer than the cut size. An example of a classification process that also results in concentration is the zig-zag classifier"' used to separate paper from glass, metal bottles, and cans during the recycle of municipal solid waste. Application of this process to minerals showing the proper specific gravity, size, and shape differ¬ences is obvious. An important device of this type is an air-aspirated screen used to remove asbestos from its associated rock during the dry processing of that mineral.144 The raw ore is crushed and screened and the asbes¬tos removed by aspiration from the surface of the screen by virtue of its shape and low bulk density. Hindered Settling. Based on the discussion in the section on "Hindered Settling Concentration and Jigging," the use of air devices could be anticipated in desert areas or where moisture may be deleteri¬ous to the product to be separated. Such processes have three major defects: (1) dust may be difficult to contain, (2) fines are difficult to process, and (3) the process is inherently less efficient than are wet processes as may be seen from Eqs. 3 and 4 in the section on "Hindered Settling Concentration and Jigging p. 4-47." Taggart142 has reported on the use of both dry panning and a dry rocker for gold separation in and regions. The dry panning makes use of winnowing, defection on the basis of specific gravity and shape during fall, and hindered settling. Prescreened placer material is poured from one pan to another as air blows across the falling stream. The process is repeated many times with hand picking to produce a rough concentrate. Magnetic minerals are then removed, and the residue, one grain deep in the pan, is air blown. In dry rocking the gravel is sized on a steeply inclined screen with the undersize fed to a riffle box with a porous bottom which is blown from underneath."' This device was the forerunner of the present-day air table. Air Tables and Jigs.145. 146 At least nine types of these devices have been developed, all but two of them for coal. While the devices used for coal may be characterized as pneumatic jigs, pneumatic tables, and pneumatic landers,145 only pneumatic jigs survive today. The same is true for ores.'" In these devices presized particles are fed to the separator which consists of an inclined vibrating conveyor with a porous surface through which air is carefully introduced to form a fluid bed. The lighter particles are lifted by the air out of uphill conveyance and float downhill, while the heavier particles in contact with the surface are conveyed uphill by the vibrator. Typically both transverse and longitudinal slopes are used. A plan view of a Triple S air table and the type of separation made is shown in Fig. 44.147 Because of its external appearance, the device has been called an air table, although it functions essentially as a jig. However, some of the asymetrical acceleration conveying function of a standard shak¬ing table is also performed by the eccentric vibrator incorporated into this device. Low pressure air is admitted below the vibrating table surface consisting of cloth (e.g., canvas), porous plastic, woven wire, or punched metal supported on a wire mesh or grid. As with a shaking table, the device produces a concentrate, middlings, and tailings. The middlings are recycled or are subsequently treated on another concentrating device. As with many wet separations, presizing by screening is necessary. The oft-repeated admonition of Professor Richards, "Separation without classification is damnation," is cer¬tainly true here. In this way a small heavy particle which might weigh the same as a large light particle and thus report to the same place on the air table has already been removed in the sizing step. Air tables are almost universally encased with a canopy to remove dust by aspiration. Some concentration may also be achieved in this step when favorable specific gravity, size, and shape differences are present. Applications Ore Separations. Air tables were originally developed for ore separations, and they find application in and regions or where water is deleterious or inconvenient to use or remove (e.g., small tonnage materials already dried). They have been used for asbestos, bauxite, calcite, cassiterite, columbite-tentalite, diatomaceous earth, fluorite, gilsonite, graphite, kyanite, manganese minerals, mica, managite, perlite, pyrite, pyrrhotite, vermiculite, and uraninite ores. More recently, air tables have found favor in separating a wide variety of secondary materials such as abrasive grains, bone char, catalysts, fiberglass, scrap glass, scrap wire from its insulation, prills from slag, dross and coke from metal or from each other, metal from crushed crucibles, lead from plastic in old batteries, and cubic particles from flat ones. The devices also finds considerable application in the preparation of food¬stuffs. As stated before close sizing before separation is desirable, and if the specific gravity difference is slight, very tight

Jan 1, 1985

By H. E. Goetzman

A cooperative research project supported by the taconite industry and the Minnesota DNR was undertaken to establish quality standards for carboxymethyl cellulose (CMC) based organic binders. The objective of this study was to identify the effect of CMC quality parameters such as degree of substitution, molecular weight, and purity as well as the effect of inorganic extenders such as sodium carbonate on performance. These factors have been evaluated by green-ball testing with two taconite concentrates followed by pot-grate tests. Balling tests with bentonite and Peridur were conducted to provide baseline data. At a constant DS the molecular weight as measured by viscosity had the greatest effect on green-ball drop strength. Dry-ball compression strength was most dependent on CMC addition rate and sodium carbonate content. DS was not found to have a major effect on green-ball quality for medium molecular weight CMC.

Jan 1, 1988

By D. K. Grubbs

Red bauxites from Breadnut Valley, Clarendon Parish, Jamaica, are very homogeneous in texture. Bauxite minerals are uniformly distributed in a groundmass, the predominant grain size being smaller than l um (Figure 1 Although the deposits have a massive, non-stratified structure, they all seem to have been affected by postformational faulting which is evidenced by shear zones running subvertically through the deposits. These shear zones stand out very clearly because of a yellow staining along their faces. Often yellow zones, ranging from a few m to several cm in thickness, have developed. When the shear zones are cut at an angle, they appear as yellow veins. Near the surface of the deposits, yellow material forms shallow irregular lenses (Figure 2). In most cases, tree roots (hair roots), or their imprints, are associated with the shear zones or stained areas. In fact, the yellowish color is especially pronounced along these roots and often disappears where the roots end (Figure 3). The mineral composition and texture of red groundmass and yellow zones are markedly different. Secondary phosphate minerals and a higher goethite to hematite ratio characterize the mineral composition of the yellow zones. It should also be noted that Al-substitution in goethite from these areas is significantly higher than in goethite occurring in the groundmass (Figure 4).

Jan 1, 1980

By H. Yoon

Several processes involving injection of sorbent and humidification water downstream of the air preheater in a coal-fired boiler unit, are being developed as low capital cost retrofit S02 control options. Extensive laboratory work, pilot plant programs and larger scale programs have developed performance data and design information. Many of these programs were supported by the U. S. Department of Energy (DOE) as "proofs-of-concept" of three different processes proposed by Dravo, Bechtel and General Electric. Based on these project results, DOE formulated a comprehensive in-duct sorbent injection development program to fully commercialize the technology by 1992. Also, EPRI will conduct a 4 MWe pilot program to develop its HYPAS process. The Consol Coolside process is scheduled for utility demonstration in 1989 on a 104 MWe unit at the Ohio Edison Edgewater Station under partial sponsorship of the DOE Clean Coal Technology Program.

Jan 1, 1989

By E. M. Frizzell

This paper addresses the use of the microcomputer programs BACKONE and BACKWEDG for an estimation of rock mass strength characteristics by back analysis of plane and wedge failures. The artificial support requirements are also determined by the programs PLANE2, BOLTPAT, and BOLTWEDG in terms of rock anchor installation angles, tensions, and installation patterns. These programs have been combined into a package called BACKPACK, which can be applied in open pit mines where some failures have already occurred.

Jan 1, 1988

By R. J. Roman

During the refining of primary magnesium metal: a spent flux (sludge) is produced which is considered a dangerous waste by the Washington State Department of Ecology. Four years of research, testing and marketing has identified two beneficial markets for the spent flux: 1) as a fertilizer and soil admendment as a result of the material's high potash and nitrogen content and its high lime equivalence and 2), as a roadway deicing agent to clear roads of ice and snow as a result of both the salt content and the flux containing chemical compounds which exothermically react with water.

Jan 1, 1988

By R. E. Nelson

The Alton Coal project, located in south-central Utah, lies at one point just over six miles from Bryce Canyon National Park. This region of the southwestern United States has been called the "Golden Circle" of national parks and monuments. Can a mine be inserted into this region so that it does not intrude on this spectacular landscape? The Alton Coal Project is a proposed surface coal mine designed to serve as the fuel source for the Harry Allen Power Plant, a 1,000 megawatt generating station planned for a site 25 miles northeast of Las Vegas, Nevada. The mine and the power plant will be connected by an underground pipeline through which coal will be transported in slurry form.

Jan 1, 1988

By R. L. Pozzo

The electrochemical nature of mineral-grinding media interaction in the wet grinding of one and two sulfide mineral ores was investigated with regard to the flotation behaviors of the minerals. Two iron sulfides (pyrite and pyrrhotite) and mild steel were used to represent the sulfide minerals and the grinding media, respectively. Galvanic currents in two-and three-electrode combinations under abrasive and non-abrasive conditions were correlated with the floatabilities of these minerals under corresponding conditions.

Jan 1, 1988

By D. L. McClure

Gold mineralization at the Colosseum Mine is submicroscopic and associated with pyrite. Pyrite occurs in breccia clasts, replacing dolomite, in crackle breccia veinlets with traces of quartz, and as disseminations in two small, interconnected intrusive pipe complexes of rhyolitic felsite and breccias of felsite and wall/country rock. Breccia types grade from felsite plus wall rock of Pre-cambrian gneiss to cross-cutting breccias "of felsite, gneiss, and Paleozoic sedimentary rocks that are in contact with the Precambrian gneiss terrane one-quarter mile (40Om) southwest of the Colosseum pipes. Mineable reserves are estimated to be 8 million short tons (7.3 million metric tons) at 0.074 troy ounces of gold per short ton (2.3 g/metric ton) at a cutoff of 0.03 troy ounces of gold per short ton (1.0 g/metric ton).

Jan 1, 1988

By Q. Xu

The new process consists of the selective coalescence of fine hematite particles by fine magnetite. The gangue minerals are dispersed by some dispersant; thus it can be separated by desliming. This process is particularly suitable for fine-grained hematite/magnetite-type deposits.

Jan 1, 1989

By A. W. Laughlin

Laser-Induced Breakdown Spectroscopy or LIBS can be used to provide exploration companies with precise and accurate chemical analyses in the field, in real-time, resulting in major time and cost savings. Using a Field-Portable Analyzer (FPA), anomalies can be followed up immediately while crews are still in the field. Lower limits of detection (LLDs) are element dependent, but many are sufficiently low to be useful in exploration. LLDs in ppm for selected elements of interest are: Be-2, Cu-3, Zn-20, As-200, Sb-500, Pb-30, Ag4, Mo-100, B-33, Ti-500, V-350, and Cr-1. LIBS analyses require little or no sample preparation.

Jan 1, 1999

By Tracy T. Morris

The current state of the mining community has made it imperative for operations to reduce costs and increase productivity in order to remain competitive. This has been done in Colorado with the installation of an Outokumpu flash flotation machine for the production of a gold/silver/lead concentrate.

Jan 1, 1987