Search Documents

By F. Calizaya, I. Duckworth

An ore-pass is an underground conduit used to transfer ore from one level of a mine to another. This method of transportation depends on the elevation energy only; therefore, it has very low operating cost. However, two inherent problems may hamper this process: (1) hang-ups of interlocked pieces and (2) a sudden release of trapped air from the ore-pass (belching). These events can create unsafe conditions with the potential for catastrophic consequences. This paper presents a summary of CFD modeling studies that were formulated to investigate the pressure build-up and belching of dust and rock particles from long ore-passes. The models were calibrated against field data collected from an actual ore-pass system and used to predict the airflow-pressure distributions in the mine for various ore feed rates and ore-pass geometries. P.T. Freeport Indonesia’s Grasberg ore-pass system (240,000 tpd capacity) was used for this purpose. This system comprises of four active ore-passes, with each being more than 600 m in vertical length.

Jan 1, 2004

By R. A. Hodge, J. W. Murray

By an order of the Executive Council of the Provincial Government dated January 18, 1979, a Royal Commission was established under the Public Inquiries Act to: 1) Examine the adequacy of existing Federal and Provincial requirements for the protection of the health and safety of workers associated with exploration, mining and milling of uranium in B.C. and for the protection of the environment and of the public. 2) Receive public input on these matters. 3) Make recommendations for setting and maintaining standards for worker and public safety and for the protection of the environment as a result of the exploration for the mining and milling of uranium ores. At that time,and at the present time in British Columbia, no uranium mines were, or are, in operation. Exploration at a number of sites was under way and one deposit, the Blizzard deposit, with estimated reserves of 1.92 million tonnes containing approximately 4.74 million kilograms of U308 was at an advanced stage of exploration. With our Terms of Reference, and because of the diverse geology of the western Cordillera which could potentially host a broad variety of uranium, deposit types, the Commission was faced with the task of considering environmental and health protection necessary for the potential development of [any] kind of uranium mineralogy situated in [any] of the environments found in British Columbia. Over the past 17 months since that time, much has transpired, culminating in the February 27, 1980 Provincial Government announcement of a seven year moratorium on exploration, mining and processing of uranium coupled with the termination of our Inquiry before completion of the hearings. The Government sebsequently modified its decision to terminate the Commission completely, deciding instead to stop the hearing but allow time for the Commission to gather in the work that had been initiated

Jan 1, 1980

By E. F. C. Ferrett

The benefits derived from the use of main fan evasees or diffusers are well known. If a well designed evasee is fitted to a fan either more air will flow through it or the same air flow rate will be discharged at a lower fan speed. This latter possibility will reduce the air power requirement of the mine, the fan input power and the overall energy costs. Despite these apparent advantages, many reports have been received from the industry of poor evasee performance. After examination, it appears that these problems are often caused by installation difficulties or inaccurate design procedures. The performance of an evasee is affected by several independent factors. Some of these factors describe the evasee geometry whilst others are concerned with the behaviour of the air as it passes through the evasee. This paper shows that the divergence angle is by no means the only ;important parameter which affects evasee performance and that the size of the inlet boundary layer has a significant influence. The performance of evasees of differing geometric shape are compared and the criterion to be used for optimum performance is discussed. It is shown that the commonly used evasee efficiency is a poor indicator of good performance. Recent work by the author and others is evaluated and a simple design. guide discussed. For more sophisticated work, details of a. computer program are provided. Finally, a brief resume of the performance of truncated diffusers is given. Since compressibility effects can be ignored for most mining applications, incompressible flow has been assumed for most of this paper.

Jan 1, 1980

By Roy E. Williams, Muriel S. Robinette

Ground-water contamination from uranium operations could be avoided with proper site analysis techniques. Contamination from tailings disposal sites is carried downgradient within permeable hydrostratigraphic units which can be located and delineated with a combination of drill holes and borehole geophysical logs. Engineering safeguards can be designed into a disposal site by determining if permeable hydrostratigraphic units exist which will dominate the flow system and provide seepage paths for contaminates. It is more cost-effective to accurately assess seepage potential with geophysical logs before contamination becomes a problem than to be faced with a major clean-up effort after contamination has occurred. If a uranium waste impoundment already has a ground-water contamination problem, then borehole geophysical logs may be used to delineate the contaminated zones which need to be cleaned up. It is less expensive to withdraw the contaminated plume from only within the affected zones rather than attempt to dewater the entire area. Consequently, the geophysical logs are invaluable in assessing which zones should be pumped and where packers should be set for construction of piezometers to allow monitoring of water-quality changes. A surface geophysical technique is being tested and developed for monitoring of seepage frum uranium tailings impoundments. Geoelectric soundings and profiles from direct current resistivity surveys can locate anomalous areas for the placement of drill holes to better assess seepage. This reconnaissance technique should eliminate random hit-or-miss drilling at sites where monitoring is required. Tests and experiments are being done on developing the capabilities of this technique to incorporate complex resistivity data to assess cultural impedence noise which complicates simple resistivity data.

Jan 1, 1980

By A. C. Beaulieu

CITY OF EDMONTON Rate of Growth The City of Edmonton has been classed by some economists as being the most progressive City in Canada since the early 50's. The high rise buildings that are changing Edmonton's skyline, the rapidly expanding sewer and water network, and the proposed rapid transit system all indicate the requirements of an ever expanding City. Edmonton, the core of Canada's Energy Empire is the country's seventh largest metropolitan area. Bisected by the 22 mile long park of its magnificent river valley, it sits in the midst of the 50,000 sq miles of riches that have created it. Underneath the City, however, extending down for thousands of feet and encircling it for a radius of scores of miles, lies a fabulous store of petroleum wealth. By the early 1940's, based upon the needs of the farming areas, accompanied by some small exploitation of coal and timber, Edmonton grew to 100,000 people. Then in a short space of 20 years Edmonton shot up to be a city of 450,000. Figure 1 (Slide No. 1) indicates the population growth in the City of Edmonton and the Census Metropolitan Area from 1906 to 1971.

Jan 1, 1997

By Oleg N. Tikhonov

A new extraction method which includes a combination of gravity and alternating electromagnetic fields with interfriction of mineral particles was proposed (Tikhonov O.N., 1979) and tested in lab conditions at Mineral Processing Department of St. Petersburg Mining Institute. At the beginning of the work the main goal was to find an efficient alternative to traditional extraction methods (like shaking table, etc.) used for concentration of fine alluvial gold particles. After the method and a series of gradually improved lab separators (Tikhonov, et al., 1983) were positively tested for gold (Tikhonov, et al.. 1986) the efficiency of the method was also proved for extraction of and other heavy minerals from alluvial and ground ores in experimental work at the St. Petersburg Mining Institute. The fine heavy minerals were separated to concentrates with high technological indices (Andreev et al., 1987), (Tikhonov, Gladkov, 1987), (Tikhonov, Gladkov 1989). In parallel a semi-industrial gravi-electro- magnetic separator was made and several technological flowsheets were designed for testing the method in industrial conditions (Tikhonov O.N., Miazin B.N., 1987), (Tikhonov O.N., Tolstunov S.A., Jebelev V.V.,1989). A series of industrial tests accompanied with complete sampling and standard technological measurements were performed at several alluvial deposits, with good technological indices. Thus the method and the flowsheets displayed high additional recovery of fine alluvial gold particles during elkrated industrial experiments in Siberia (Aldan province). At higher concentrate grade this method, even in one-stage operation, increased gold recovery more than by 25% compared with shaking table (for particles -0.10 mm gold recovery was 82% vs. 55% by shaking table, for particles - 0.25mm the recovery was 97.5% vs. 61.8%). Experiments were performed by joint team of St. Petersburg Mining Institute and the Irkutsk Institute of Rare Metals (Tikhonov O.N., Gladkov S.A., Tarasova T.B., 1991).

Jan 1, 1995

By K. Biswas, H. C. Lee, S. J. Jung

Ore passes are circular openings excavated in rock for in-mine gravity-transportation of ore. It is a very important component of the overall load-haul system of an underground mine. The function of an ore pass is two-fold: first, gravity-transportation of ore from the extraction level to the haulage level and second, the loading operation at the haulage level utilizing the gate assembly. In reality, like any other system component, an ore pass breaks down either due to a hang-up within the ore pass or due to a failure in the gate structure. The failure of the gate assembly may be attributed to a greater extent to the impact load as experienced by the components of a gate structure as a result of the direct impacts of the rock fragments and to a lesser extent to the static or 'dead weight' loads of the accumulated materials in the ore pass. This paper uses simulations in Working Model® as an aid to investigate the effect of both the impact and static loading on the gate assembly and on the inner-walls of the ore pass. The paper also investigates the impact of ore pass inclination and the presence or absence of dogleg on the static and impact loading of the same.

Jan 1, 2002

By John A. Shuster

INTRODUCTION Controlled ground freezing for mining and construction applications has been in use for over a century. Despite the great technological evolution which has occurred during this period, ground freezing is still used on projects today with much the same basic technology as that used originally over 100 years ago. Major developments have occurred in the separate fields of frozen soil mechanics, refrigeration, and heat transfer analysis. However, except for a few projects in Europe and Asia, these developments have not been combined to upgrade ground freezing techniques to their potential level. In view of this situation, it is believed desirable to examine the art of ground freezing in light of recent technical developments, together with highlights on some of the apparent advantages, disadvantages and economics of the various alternative approaches. The purpose of this paper is to attempt such an examination, with particular emphasis on the practical application of presently available technology. GENERAL ADVANTAGES AND DISADVANTAGES Ground freezing may be used in any soil or rock formation, regardless of structure, grain size or permeability; however, it is best suited to soft ground rather than rock conditions. Freezing may be used for any size, shape or depth of excavation and the same physical plant can be used from job to job despite wide variation in these factors.

Jan 1, 1997

By Michael J. Shulman

During-all phases of exploration limited resources must be allocated among exploration methods and among exploration prospects. This problem,, an exercise in optimization, can be treated mathematically. For three objective functions - maximizing return, return to cost and return minus weighted cost - theoretical results exist which enable the exploration planner not only to gain valuable insight into the problem, but also to estimate the resources necessary and to allocate these resources for' at least-two stages of exploration prior to initial field work. A two-stage exploration strategy for volcanogenic-sedimentary iron in northern Egypt illustrates, how the results can be used. Stage 1 consists of an aeromagnetic survey to map the structure of five areas;" stage 2 consists of field reconnaissance work. For the three objectives, lower bounds are calculated as a function of exploration expenditures for each stage in order to facilitate the choice of an-optimal exploration budget. Nomograms are then presented which, based on the Kuhn-Tucker Conditions', enable the incremental allocation of airborne and reconnaissance effort among the five areas.

Jan 1, 1989

By Ryota Kasahara

In 1981, a gas outburst accident occurred in the Yubari Shintanko coal mine, the only expectant mine in Japan, it caused 93 deaths. As a result, Yubari Shintanko closed in 1982. This major disaster was a turning point for sustainability of Yubari City, the largest coalfield in Japan. Finally, Yubari City was bankrupted in 2007. This paper aims to explore how miner’s children experienced this disaster and felt about region, family, and themselves, and to explain the relation between region declining and children’s lives. The data of this paper are the archived 600 essays, written by the junior high school students at the time of the disaster. There are three findings. First, the children who lost their father were the most shocked. They faced profound sadness. But they expressed that they had decided to overcome their sadness with surviving family. Second, the children who didn’t lose their father were also influenced. They were anxious about the future of Yubari, their family, and themselves. Furthermore, they decided to strive for their future. Third, they understood the disaster as a turning point of Yubari declining and looked ahead their future outside of Yubari. In conclusion, this disaster created their hopelessness to Yubari region and, as a result, promoted the decline of the city through their migration to other city. Furthermore, it is important to clarify that Yubari City has to continue the struggle to the regeneration.

Jan 1, 2017

By B. Basim

Novel chemicals that can be used for increasing the efficiency of fine coal dewatering were developed at Virginia Tech. Reagent A was tested on three different coal samples in laboratory vacuum filtration tests. These included flotation products from Middle Fork plant, Elkview Mining Company, and CONSOL, Inc. The tests conducted with the Middle Fork coal sample (100 mesh x 0) showed that cake moisture can be reduced by more than 10% beyond what can be achieved without using dewatering aid. This improvement was achieved at 1 lb/ton of Reagent A and 0.1 inch cake thickness. At 0.5 inches of cake thickness, the improvement was limited to 8% at the same reagent dosage. The results obtained with the Elkview coal (28 mesh x 0) showed similar advantages in using the novel dewatering aid. Depending on the reagent dosage, cake thickness, drying cycle time and temperature, it was possible to reduce the cake moisture to 12 to 14% range. In addition to achieving lower cake moisture, the use of Reagent A substantially decreased the cake formation time, indicating that the reagent improves the kinetics of dewatering. The test results obtained with CON SOL coal were not as good as with the other coals tested in the present work, which may be attributed to possible oxidation and/or contamination.

Jan 1, 1998

By Javad Sattarvand, Frimpong Kwaku Asare

The safe evacuation of miners during an emergency in the shortest amount of time is one of the most essential features of a mining operation. Despite advancements in mine evacuation research, the usage of mine vehicles during evacuation has not been considered. The majority of recent studies have been done on miners’ evacuation on foot. Mathematical formulations including Minimum Cost Network Flow (MCNF) models, Dijkstra's algorithm, Floyd-Warshall algorithm, and Ant Colony Optimization models have been used to solve mine evacuation problems. These models, which concentrate on determining the shortest escape routes during the evacuation, have been found to be computationally expensive and may not offer the best solutions in some cases. The goal of this paper is to incorporate light vehicles in the evacuation process using a mixed-integer programming approach. The methodology aims to minimize the total time required to evacuate the mine, ensuring minimal exposure of the miners to the adverse conditions that triggered the evacuation.

Jun 25, 2023

By J. T. Crawford

Computer techniques for open-pit limit analysis were introduced into Kennecott Copper Corp. (KCC) during the early 1960's. The first computerized approach used block matrix mineral and economic models, and a removal increment mining simulator. A detailed description of the approach was published in the May issue of Mining Engineering (Carlson, et al., 1966) and also in Chapter 30.3 of the SME Mining Engineering Handbook (Pana and Davey, 1973). Since then, many refinements have been made to improve the system and the resulting pit limit design. The fundamentals, however, generally remain unchanged. Computerized open-pit limit analysis is presently used by Kennecott's open-pit copper properties and by the Quebec Iron and Titanium Corp. The system and the fundamental evaluation techniques it represents are cornerstones of all open-pit mine planning activities within KCC. This case study describes a typical example of open-pit limit analysis within KCC. The case involves a copper sulfide porphyry deposit with additional minor amounts of molybdenum, gold, and silver. The ore-grade mineralization within the pit design will be mill feed for a sulfide ore concentrator, and subore grade mineralization will be classed as waste and placed on dumps. The contributions to production and profits from dump leaching are insignificant, having minimal effect on the pit economics and design, because the material responds poorly to leaching solutions.

Jan 1, 1979

By R. C. Karra

Mining is one of the oldest profession and second after agriculture. Unfortunately Mining is not so familiar in the society. Due to lack of recognition in the society, existence of mines in remote places and in dusty and humid working conditions, led the poor response for mining engineering. Mining engineering programs have been increasingly less attractive to the student population over the years due to negative image of mining industry. After graduating in mining engineering, there is not much problem of employment at present. In the last 10 to 15years most of the mining engineering graduates have joined software industry. Even those joined in mining industry also left with in 2 years of service. The main reason for this is not being satisfied with job, it is not only working conditions but also work environment, work culture, remote location of the mines etc. Though many were trying to leave mining profession, the recent economic slow down has prompted some of them to incline towards job safety and retained to mining job. At this juncture a systematic study was taken up to analyze the job satisfaction of mining engineers in India.

Jan 1, 2011

By William Moser, B. P. Shagula

INTRODUCTION Every day mine management and mining personnel face the threat of a possible mine disaster or fire. Their ability to deal with such a situation safely and effectively depends on the level of emergency preparation developed and maintained. After conducting numerous informal evaluations or audits at different mine sites throughout West Virginia (as well as other states), the authors concluded that many mining operations are not prepared to handle a fire situation. The results of the audits indicate that while most mines are in compliance with federal and state legal regulations regarding levels of emergency equipment, water systems and training sessions, these levels - particularly in the area of fire training - are probably not sufficient to enable the mine employees to effectively combat a fire in its early stage. This paper will present the authors' recommendations for designing and maintaining an efficient mine emergency preparedness Program and an overview of the curriculum of the mine fire training Program currently being conducted. MINE EMERGENCY FXEPAREDNESS PROGRAM The Mine Emergency Preparedness Pro- gram (MEPP) is a management tool developed by the Mining Extension Service at West Virginia University and was designed to assist company personnel in effectively managing a mine emergency operation. The program goes beyond the traditional and required training of mine rescue teams by offering a complete emergency operations package. Included in MEPP are suggested approaches for training and organizing all personnel, ideas for developing plans of action concerning transportation, security and communications. The MEPP program may also be used as to assess present readiness levels. While the MEPP program is designed to address all types of emergency operations, the authors are convinced that emergencies involving mine fires are the ones of greatest concern and so are concentrating their efforts in that direction. Incidents where fires are involved seem to be increasing in frequency and are extremely costly to control if allowed to go beyond the incipient stages. With a proper emergency preparedness program in place and properly trained and equipped fire brigades, the authors feel that it is possible

Jan 1, 1992

By Barton Kelby Cross

In the early 1960's the feasibility of mathematical modeling was demonstrated in Northern Rhodesia and southwestern United States, where techniques were developed to use these models in a new approach to aid engineers in the estimation of ore reserves, mine designs, and financial evaluations. These rudimentary models closely followed the manual methods, producing ore reserves and production schedule estimates that were as accurate as the manual methods, yet were many times faster. Mines evaluated and designed using these new tools gradually came into operation during the 1970's and entered the phase at which production scheduling and ore-grade control became day-to-day problems. Management expected the number of operational engineers to be small because small planning engineering staffs had produced the original designs and operated the smaller high-grade pits. Unfortunately, the tools needed by the mine engineer to perform short-term production scheduling and ore-grade control were labor intensive; they had not yet been generally computerized. Several attempts to use the original or exploration model for these two functions were futile. While an exploration model based on data from exploration work proved sufficiently precise for overall mine design and long-term production scheduling, the model lacked the precision required for short-term scheduling and grade control.

Jan 1, 1979

The estimation of local recoveries, such as the local recovered tonnage of ore and its corresponding grade at a given cutoff grade, is an important problem in a selective mining operation. Multigaussian kriging provides a simple solution to this specific problem. The solution is also complete in the sense that local recoveries are estimated together with their estimation variances. It is thus possible to assess confidence limit intervals on the estimated recoveries. Multigaussian kriging has been applied to the Jerritt Canyon deposit in a most realistic situation. The various steps of the estimation procedure are presented in detail and the potential of the method is demonstrated in view of the results. The obtained results show that the estimated recoveries are in good agreement with the actual recoveries and the actual estimation errors are correctly predicted by the estimation variances. Multigaussian kriging thus appears as a useful and fully operationable tool for the mining industry.

Jan 1, 1986

By Byron Belew, Juris R. Harlamovs, D. B. Dreisinger, John L. Watson, G. A. Kordosky, Thomas O. O’Keefe

Unwanted impurities, present in raw materials, are often coextracted along with desired constituents during leaching. Due to its abundance and ease of extraction, the presence of ferric iron in leach solutions, solvent extraction circuits, and subsequently in electrowinning circuits, has always been a problem. In the case of zinc hydrometallurgical processing, iron is frequently an impurity in leach solutions. Purification of such solutions by solvent extraction, using di (2-ethylhexyl) phosphoric acid (D2EHPA) in a kerosene diluent, results in ferric ions being readily extracted along with zinc into the organic phase. Ferric iron has proven difficult to strip from the organic phase, but it is known that ferrous iron may be easily stripped from D2EHPA, and hence a process to effect reduction of iron present in the organic would have great potential. This research investigated a process to directly reduce ferric to ferrous iron in the organic phase, and to strip the ferrous iron using a dilute acid solution. The process utilized metallic zinc as the reductant and a low concentration sulfuric acid stripping solution. The results of the laboratory tests illustrated that iron could be readily removed from the organic phase by simultaneous direct reduction and acid stripping. The reductive stripping process was subsequently utilized in industry at the laboratory and pilot plant levels. The results of the industrial tests were encouraging and demonstrated the potential of this novel concept.

Jan 1, 1993

By Paul B. Queneau, Barry J. Hansen, D. Erik Spiller

Most lead and zinc secondaries are recycled pyrometallurgically. However, many problems encountered in secondary smelters have been solved by addition of physical concentration and/or hydrometallurgical processing steps, with resulting important environmental benefits. U.S. secondary lead and zinc operations are described, covering conventional smelters, EAF-dust treaters, and zinc sulfate/fertilizer producers, including plant capacities, technologies, and outputs. During the past two decades, remarkable advances have been achieved by recycling spent lead-acid battery components. Interaction between primary and secondary zinc producers, the fertilizer industry, and the zinc chemical industry has substantially decreased waste generation.

Jan 1, 1993

By B. M. Sadashiva Murthy

Increasing quantities of nutrients and pesticides in agricultural runoff in recent years has caused the more developed western nations to become concerned about diffuse agricultural pollution. Thus, the problem of diffuse pollution is of greater importance and concern for any integrated water quality management programme. The above mentioned sources and activities causing pollution to groundwater cannot be completely avoided. The best solution is to entail a firm understanding of the principles of solute transport through porous media. The complex factors that control the movement of contaminants in porous media and the resulting behavior of contaminant plume are usually intricate to assess because of interaction of many factors such as dispersion, advection, sorption, degradation, volatilization, etc. As accurate quantification of solute under field conditions is inherently difficult, the fate of nitrate and phosphate have been analyzed in laboratory column and channel studies. From the analysis of the breakthrough curves, the dispersion co-efficient for nitrates and phosphates through sandy soil was found to be 0.262 m2/d and 0.114 m2/d for column studies, 0.321 m2/d and 0.231 m2/d for channel studies respectively. The column studies revealed that the concentration of nitrates and phosphates increased steadily in the first few days (around 5 days) and then it increased rapidly after 8 to 10 days. However, it attained equilibrium after 20 days. Similarly, the channel studies revealed a steady increase in concentration of nitrates and phosphates in the first few days (1 to 2 days) and rapid increase up to 15 days and there after it attained equilibrium. In the study, one-dimensional analytical model has been developed which include the advection, dispersion, and a characteristic term called ?total elimination rate?. The comparative study of column and channel studies, and model output (in which the term total elimination rate ?K? is considered as zero) exhibited a variation of 30 to 50 % in leaching characteristics of pollutants (nitrates and phosphates).

Jan 1, 2008