Search Documents

By J. D. Miller, C. L. Lin

Liberation of valuable minerals during size reduction is an important aspect of mineral processing technology. In practice, most quantitative information on liberation is based on the application of stereological theorems for the analysis of image data from two-dimensional polished sections. On this basis an estimate of the volumetric grade distribution is made. Recently, a new method based on cone-beam xray microtomography has been used for direct determination of the three-dimensional liberation spectrum of multiphase particles 100 microns in size or less. Preliminary results for a packed bed of particles indicate that high spatial resolution (approximately 15 microns) and the direct processing of raw volumetric data are two important benefits offered by this new method. Three dimensional liberation analysis by microtomography provides an excellent opportunity to overcome many of the limitations of currently used polished section techniques. For example, detailed textural information is provided. Of course microtomography provides an independent method to verify current procedures used for analysis and transformation of polished section data into an estimate of the volumetric grade distribution. More important, however, is the possibility that this method could be developed as a routine procedure for liberation analysis in the 21st century.

Jan 1, 1997

By Eduard Hamm

The main reasons for the development of higher heat levels in German coal mines are the increasing depth of working with the con- sequent higher rock temperatures, increased use of electrical equipment, and increasing coal output due to concentration and mechanisation of workings. In place of the normal decentralised underground cooling plants, schemes and pilot plants have been developed to produce the required cooling capacities in central air cooling units, which then supply the cold air to the underground working points where needed.

Jan 1, 1980

By Shaning Yu, Yosry A. Attia

The purpose of this work was to investigate the feasibility of using column flotation as a floc separation technique. In this study, the ultrafine coal (minus 25 microns) slurries were cleaned by using the Integration of column flotation with selective flocculation. It was found that using column flotation as a floc separation technique during the "cleaning" stage, achieved much better results than that either using column flotation as a rougher separation technique for coal flocs, or using It directly to recover the ultrafine coal from the slurries without adding selective flocculant. Thus, the ultrafine coal slurries were first separated by selective flocculation process to reject a certain amount of the dispersed ultrafine ash minerals, and to aggregate the ultrafine coal particles as flocs. Thus, the entrainment of ultrafine ash minerals Into the coal floc-froth concentrate during flotation could be considerably reduced. Subsequently, the coal flocs were further "cleaned" by column flotation. The experimental results Indicated that this approach was technically feasible and particularly suitable for a slurry containing a large amount of ultrafine particles. The effect of flotation time, and collector dosage on column flotation of coal flocs were also Investigated and reported In this article.

Jan 1, 1988

By J. Chia, M. H. Kobler, J. Cheung, M. J. Robison

INTRODUCTION The Lake Merced Transport is being constructed as part of San Francisco's Clean Water Program. The Clean Water Program, which began in the early 1970's, is designed to control wet weather, storm sewage overflows into the Pacific Ocean and San Francisco Bay. To accomplish this goal, a system of large underground storage and transport facilities, pump stations, modernized treatment plants, and outfalls is being built. By 1991, eighty percent of the system had been completed and was in operation. One of the remaining projects for the Clean Water Program is the Lake Merced Transport. The Lake Merced Transport is located in the extreme southwestern portion of San Francisco, as shown in Figure 1, Project Location. The transport will convey dry weather flow from the existing Lake Merced Pump Station to the Westside Pump Station. During wet weather, the transport will fill with sewage and runoff, with a storage capacity of 36 million liters. The Lake Merced Transport was expected to be excavated entirely within the Colma Formation, an alluvial deposit consisting of weakly cemented sand. Once excavation of the access portal at the Sloat/Great Highway parking lot began, it became evident that a portion of the tunnel would be excavated through beach/dune sand. Based upon the expectations of the Geotechnical Design Summary Report (GDSR), encountering beach/

Jan 1, 1993

By Qing Wang

A longterm overburden removal plan can be realistic and optimum only when the cost and capacity profiles off the equipment assigned to the operation are taken into consideration. Therefore, the planning should involve the proper assignment of equipment capacity by insuring a timely investment and a timely replacement policy throughout the mine life. A dynamic solution algorithm has been developed, by which all possible truck fleet alternatives are evaluated for each year off the operation. Cumulative cost off the operation is carried throughout the analysis. The optimum solution is obtained by selecting the minimum cumulative cost at the last year and tracing backward the best fleet alternative for each year. The solution provides: 1. the optimum amount of overburden to be removed each year; 2. the best fleet to be assigned to the job; and 3. the best equipment replacement policy.

Jan 1, 1989

By R. R. Tatiya

This paper describes the local estimation of mineral inventory by kriging. A mineral deposit located between two working levels of a copper mine was examined. Data for this estimation was obtained by underground diamond drilling. The mineral inventory that was computed by this method was compared to the results obtained by global estimation techniques, which were based on information front surface boreholes. A comparison between the ore reserves estimated through kriging and the ore reserves estimated at the mine using conventional methods was also made. This analysis shows that geostatistical methods can be applied to evaluate base-metal deposits similar to the deposit examined in this study. In the part of the mine that was examined, the kriging estimates show an overall increase in metal content at all cutoff grades, compared to the estimates obtained through conventional methods. Also, the ore body profiles are more continuous and regular through kriging, but they are not radically different from the profiles that were previously obtained at the mine. However, the global estimate of the deposit using kriging could not provide reliable results.

Jan 1, 1997

By K. L. Whitehead, R. A. Jankowski, N. I. Jayaraman

Most continuous miner sections utilizing flooded-bed scrubbers also use blowing face ventilation. Blowing ventilation, however, interferes with dust capture and minimizes scrubber effectiveness. To enhance the efficiency of the scrubber system and reduce dust concentrations, the Bureau of Mines tested various combinations of operating parameters. Experiments for system efficiency took place in a full- scale model mine at 3.05 m roof height. In general, higher values for scrubber and face airflows resulted in lower dust concentrations. In addition, optimum dust controls would include a face ventilation to scrubber airflow ratio of one. When the airflow ratio was either less than or greater than one, the dust levels in the return and at the operator locations increased. No single dust control technique was the most effective one at all locations due to mutual interaction among techniques.

Jan 1, 1992

By S. Chander

The advantages and disadvantages of various techniques available for controlling reagents in the mineral flotation systems are discussed. Special interest is placed on potentiometric and voltammetric sensors for monitoring flotation pulps. Different approaches to increase the sensitivity of detection and to facilitate in-stream monitoring of solution species are also discussed. The potentiometric sensors are simple to use but are limited by the availability of an electrode reversible to the species to be monitored. In some cases the response signal could be unreliable due to the presence of interfering species. In comparison, voltammetric sensors require a higher degree of instrumentation which, however, provides an opportunity to decrease interferences and increase levels of detection.

Jan 1, 1993

By Jean-Claude Bianchini, Paul Bauernfeind, Erwin Gartung

Introduction The city of Nuremberg, located in Bavaria in the Federal Republic of Germany, started building a subway in 1967. The construction operations began in a southern suburb, where no complications were encountered in the design and execution of the job. As the first subway line approached the downtown area of the city, the civil engineering challenges increased rapidly. Tunnels had to be excavated next to, or below precious historical buildings, and the work of the responsible engineers was closely watched by the public, who were very anxious about any damage to the existing beautiful old houses and churches. The job has been handled successfully to date in cooperation with the owner-designer, the geotechnical consultant and the contractors, who jointly went through a process of systematic learning and gathering of experience, and who developed a modern tunneling technique specifically tailored to the natural properties of the encountered ground conditions and the requirements of the city of Nuremberg. The application of scientific methods has been an important part of this development. Research into the geotechnical properties of the predominantly encountered soft Keuper sandstone, studies of the geomechanical performance of grout reinforced sand sections and finite element analyses of various tunnel problems for the prediction of displacements, for the assessment of stability, or

Jan 1, 1979

By H. Sevim

In long-term open pit production planning, a series of nested and maximum-value pits is usually generated first. These pits are then considered as possible pushbacks over a number of planning periods. To determine the best pushback in each planning period, the pits are evaluated for their technical and economical feasibilities under certain production constraints. Parameterization is a commonly used technique to generate a series of pits. In almost all cases, however, some of the consecutive pits generated by this technique are too far apart from each other. This is called the "gap" problem. It may make the entire pit series useless for production planning purposes. A new pit gener¬ating algorithm has been developed to overcome the gap problem. Through this algorithm, a series of nested maxi¬mum-value pits can be generated with a controllable size increment. The logic of the algorithm is illustrated through a small hypothetical case. Its capability of generating maximum-value pits that are as optimal as those generated by parameterization and its advantages over parameteriza¬tion are presented through an actual gold deposit case.

Jan 1, 1996

By Jan M. Mutmansky, David R. Kalasky

Computer simulation continues to be one of the most successful analytical applications of computers in the mining and mineral processing industries throughout the world. Through simulation, managers and engineers can explore the impact of new technologies, equipment designs, plans and operating strategies to improve their operations. It is not uncommon for a single simulation application to provide a quick payback of analysis expenses (within weeks or months) yielding long-term financial and operational dividends. The paper will present a summary of the types of software systems that are available for use on PCs and other computer systems. Support software for curve fitting, statistical analysis, and optimization of simulation models will also be presented. Methods of leveraging simulation efforts through networking and coupling of software systems will be discussed. Finally, the trends in simulation in the mineral industries will be analyzed. Areas of strength and weakness of simulation will be discussed along with the usefulness of commercial general-purpose and custom-writ- ten simulation packages. The future possibilities for simulation in the mineral industries will be outlined and predictions on trends for the future will be presented.

Jan 1, 1996

By R. A. * Russell, J. R. * Brooks, E. J. Griffith

In 1967, a major impoundment to contain phosphate tailings was built near Columbia, TN. Precise records were maintained on the behavior of the impoundment throughout its 20-year active life. The volume of the impoundment was determined. The DNT (dry net tons) of solids added to the impoundment were continuously measured. The rise of the mud line in the impoundment was measured monthly. The density of the settled strata was determined, as required to understand the behavior of the settled tailings. And experiments were per formed to increase the settled density of the clays. The impoundment is currently being retired and stabilized. It covers more than 400 acres and the settled muds are almost 200 ft thick. The clays have been sufficiently solidified with electroendosmosis to support the growth of cypress trees. More than three milllion trees are being planted.

Jan 1, 1992

By David G. Laughton, Richard Poulin, Michael R. Samis

Real options (RO) valuation is an alternative net present value (NPV) framework that is able to incorporate both management flexibility and dynamic project risks. In this paper, management is considering the development of a satellite low-grade zone while operations in a developed high-grade zone continue. If the low-grade zone is developed prior to high-grade zone exhaustion, mine capacity must be expanded before additional production from the low-grade zone can be processed. This expansion can be avoided only if low-grade zone development is delayed until the high-grade zone is exhausted. The RO model presented here allows the development and capacity expansion decisions to be reconsidered on a discrete half-year basis. It delineates price regions, for given levels of high-grade zone reserves, in which it is optimal to develop the low-grade zone, defer low-grade zone development and abandon the mine irrevocably.

Jan 1, 2002

By J. A. Herbst, Y. C. Lo

An attempt has been made to parameterize the population balance model for a ball mill based on measurements of the elementary breakage process obtained using an ultrafast load cell device. Detailed insight obtained concerning the fragmentation of particle assemblies with the ultrafast load cell leads to a better understanding of ball mill grinding. The ball mill breakage function and specific selection function are derived from an average single event representing the multiple breakage events which occur in ball mill grinding. Since both the breakage function and the specific selection function depend on the loading mode in the mill, predictions of breakage mechanisms in ball mills are possible by using data obtained in various elementary loading modes. The application of this model to the description of batch ball milling behavior has resulted in reasonably accurate predictions of product size distributions for various energy inputs.

Jan 1, 1992

By E. R. Braer, C. J. Bise

The trend in underground room-and-pillar coal mining is to employ remote-controlled, continuous-mining machines and extended cuts to depths of 12 m (40 ft) or more. This system of coal extraction, adopted by more than 435 mines, can create additional worker safety hazards. To address the ground-control-related safety hazards, a combination of statistical analysis and numerical modeling was used. Initially, the reported roof-fall incidents and fatalities were reviewed to delineate the ground-control hazards. Then, the application of the coal mine roof rating (CMRR) for estimating safe extended-cut depths was evaluated. Finally, computer modeling was completed to predict roof displacements during extended-cut mining. This paper describes the results of these studies and their impacts on the safety of extended-cut mining.

Jan 1, 2000

By P. J. Suardini, S. K. Kawatra

A number of on-stream coal slurry analyzers are presently being developed and commercialized for measuring ash and solids in coal process streams, particularly around flotation circuits. The eventual goal of these efforts is to develop on-line quality control systems for flotation circuits and other fine-coal cleaning operations. As part of this on-line monitoring and control effort, it is important to gain a better understanding of the response of industrial flotation circuits to changing operating conditions. This paper summarizes the results from a detailed sampling program performed at an industrial coal flotation circuit in western Pennsylvania. The testing focused on evaluating the response of the circuit to changes in reagent dosages, operating conditions and feed compositions. The testing indicated that it is desirable to maintain high collector-to-frother ratios to enhance coarse particle flotation. The recovery of fine impurity particles was also proportional to water recovery, due to hydraulic entrainment. Key words: Industrial, Coal, Flotation, Circuit, Reagent, Response.

Jan 1, 1995

By Robert A. Haney

Utilizing the recently developed laser velocimeter and a Pitot-static tube, the United States National Bureau of Standards (NBS), has calibrated various types of anemometers that are commonly used in the mining industry. This paper presents a summary of the performance characteristics including accuracy, precision, starting and stopping speeds of each instrument tested. The specific instruments that were calibrated by NBS have become Mine Safety and Health Administration (MSHA) primary reference instruments. These primary reference instruments are used in turn to calibrate secondary reference instruments for each Coal Mine Safety and Health District. Each District calibrates anemometers that are used by District engineers and inspectors. Calibration is accomplished through a substitution procedure in which the reading on the anemometer is compared to the true velocity determined by the reference instrument. Calibration is performed over the entire range of the instrument using an open jet wind tunnel to produce the various approximate velocities. Some specific details of the calibration procedure are presented in this paper.

Jan 1, 1980

By L. Xu, S Jones, R. Bhaskar, J. McKenzie

The objective of this project was to optimize the ventilation parameters of a continuous miner underboom scrubber. This would result in further control of the amount of airborne dust discharged during mining, reduce the exposure of face personnel for an exhaust brattice ventilation system, and avoid recirculation of contaminants at the face. This research was performed in an underground coal mine in Utah. The tasks performed included preliminary face ventilation evaluation, and optimization of the scrubber system to eliminate recirculation of the scrubber discharge air. Airflow tests were conducted on the currently used dust control system and the modified scrubber system. Tracer gas tests were performed to evaluate face ventilation effectiveness. Confirmatory tests of the scrubber system under actual operating conditions, modifications to the scrubber system and a comparative evaluation of the scrubber system vs. the existing system were performed. This paper presents the results of the airflow pattern tests and the respirable dust levels in the modified scrubber system and the existing system. The optimized face ventilation parameters and the developed operating guidelines may provide the benefits of dust reduction, better lace ventilation and improved visibility.

Jan 1, 1994

By Numan Elmas

Barite deposits located in Dinek and surrounding region have important economic features with their large reserve capacity for Turkey. The objective of this study is to elucidate geological and depositional characteristics in terms of. site investigation and chemical analysis. In order to do this, geological area of about 300 km2 was examined and detailed geological map was constructed. It was observed that Barite mineralization in these deposits was occurred in carbonate and pelitic rocks of Lower Cambrian-Lower Ordovician. Deposits were exposed to advanced diagenesis regional metamorphism and tectonics that rotated and deformed the barites; therefore, barites shows secondary veins, brecciate and fracturing structure. Even though, a few light isotope values of barites may suggest hydrothermal and exhalative sedimentary characteristics or possible mixing with magmatic fluids, generally heavy isotope values indicate that the sulfate ions were supplied from coeval seawater and, many of sedimentary features and petrological, geochemical characters support dominantly sedimentary origin.

Jan 1, 2005

By DeVerle P. Harris

The structure of an exploration model reflects a number of design considerations, one of which is the question or issue-to be investigated by the model. Thus, a model designed to evaluate the magnitude of risk and its economic implication to optimal decision making at each decision juncture of a multistage exploration architecture differs considerably from one designed to evaluate, say, the long run average cost of discovery, in which the architecture of exploration is suppressed and risk is simply an element of average cost. The perspective of the model examined in this paper is that exploration is investment in (purchase of) information and that the next stage of an exploration program is undertaken only when the expected value of information to be acquired in that stage exceeds its cost. The degree to which this perspective is honored influences considerably model design. Consider two design objectives:

Jan 1, 1989