Search Documents

By V. B. Achanti

This paper deals with the effect of various bit geometric parameters on failure characteristics of rock material. Improvement of rock cutting efficiency of continuous mining machines has been an interesting research topic for the last few decades. In the current study, an automated rotary rock cutting simulator, duplicating a continuous miner, was utilized to study these parameters in the laboratory. Improvement of bit performance in terms of its life, cutting efficiency, dust production and energy consumption has drawn wide spread attention over the years. Research shows that optimizing bit parameters can result in efficient fragmentation of rock. Indiana limestone rock material was utilized in this study while bit tip angle, bit tip size, bit spacing, depth of cut and cutting velocity of rotary drum were varied to investigate the failure characteristics. The cutting pressure, penetrating pressure and the depth of cut were monitored on the simulator during the cutting process. Air borne dust and settled dust were measured for each experiment. Then, the specific airborne dust and specific energy were determined for the each type of bit. Triaxial tests were carried out to correlate the failure angle of the rock in static case to dynamic cutting process failure. The physical and mechanical properties of the rock were also determined in order to assess their influence on the wear characteristics of each bit.

Jan 1, 1998

By Y. T. M. Ocsa, V. O. Tenorio

This research is the result of a geotechnical study carried out in a natural slope in an Open Pit mine in Southern Peru, highlighting earthquakes as an important cause of instability within the case study presented. This leads to analyze the stability of a slope, according to the safety factor and thus consider a future construction in its environment according to the identified requirements. There are known disasters at national and international level that involve human lives because of the lack of analysis of slope stability conditions, which based on the results will allow to control and to take adequate corrective measures. These mass movements are classified whether they are soils or rocks, considering the mechanism and type of rupture, as well as the presence of water, the speed and magnitude of the movement. The movement problems are due to factors of inherent nature and constitute a reason to perform a calculation study to analyze and estimate the safety factor of each of the evaluated cases

Mar 2, 2022

By R. A. Haney

The Mine Safety and Health Administration has developed a model to estimate diesel particulate (dp) exposures in underground mines. The estimate uses either in-mine measured dp concentrations or engine manufacturers' standardized emission data and through a series of calculations estimates full shift dp concentrations by applying standard engineering principles of ventilation, control technology and work cycle. This model, in the form of a computer spreadsheet, provides the mining industry with a method to estimate diesel particulate levels and determine the impact of various diesel particulate controls on occupational exposure to dp in underground mines. A detailed description of the estimator and several examples demonstrating the results are provided.

Jan 1, 1998

By S. Lin

Fan stall is a notorious phenomenon with axial-flow fans. When multiple fans of this type serve a ventilation system, their mutual impacts are very complicated and not well understood. Results from laboratory experiments indicated that the immediate consequence of a fan working across its stall zone (i.e., the pronounced trough on the fan characteristic curve) is that some branches in the system may suffer abrupt and even drastic changes in air quantity and pressure. The quantity range of the fan that causes the abrupt change is called an unstable operating range. The corresponding quantity range of a branch is called a non-achievable quantity range of the branch because any quantity within this range cannot be achieved without changing some parameters of the ventilation system (e.g., branch resistances). These concepts are introduced based on the test results from tubing networks to bring attention to these important characteristics of ventilation systems.

Jan 1, 1996

By D. W. Park

Longwall mining is popular in underground coal production in the United States due to higher production rates and safety concerns. Because of the extreme complexity, it is necessary to plan an adequate design to achieve a safe and efficient working place. The proper sizes of yield and abutment pillars and panels can be determined by simulation using numerical modeling techniques. By means of three-dimensional modeling, stresses to be imposed on the pillars, panels, gob, and powered supports can be analyzed. In this study, an initial three-dimensional finite element model was developed and then modified into four different models. Using these models, the numerical outputs of distributed stresses on three different sizes of yield pillars, three different sizes of panels, and two different sizes of abutment pillars were compared and analyzed to determine the most adequate pillar and panel sizes. Progressive failure theory based on the Hoek and Brown failure criterion was used to determine redistribution of stresses in the yielded and failed areas in the longwall mine.

Jan 1, 1992

By L. Yuan, J. Soles, D. Bahrami, W. Tang, R. Thomas

Mine equipment fires remain as one of the most concerning safety issues in the mining industry, and most equipment fires were caused by hot surface ignitions. Detailed experimental investigations were conducted at the NIOSH Pittsburgh Mining Research Division on hot surface ignition of liquid fuels under ventilation in a mining environment. Three types of metal surface materials (stainless steel, cast iron, carbon steel), three types of liquids (diesel fuel, hydraulic fluid, engine oil), four air ventilation speeds (0, 0.5, 1.5, 3 m/s) were used to study the hot surface ignition probability under these conditions. Visual observation and thermocouples attached on the metal surface were used to indicate the hot surface ignition from the measured temperatures. Results show that the type of metal has a noticeable effect on the hot surface ignition, while ventilation speed has a mixed influence on ignition. Different types of liquid fuels also show different ranges of ignition temperature. Results from this work can be used to help understand equipment mine fires and develop mitigation strategies.

Mar 2, 2022

By Sidney A. Hiscock

INTRODUCTION Lead and zinc are today rightly regarded as sister metals. Historically, however, they differ markedly with lead being known and in general use as the metal since 3000 BC in several countries which at that time might have been described as mature economies. Zinc was not isolated and recognised as an industrial metal with distinct and valuable properties until about 1700-1800 AD (although it had, of course, been utilised as a constituent of brass for some 2000 years previously). c were well established as industrial metals by the beginning of the 20th century. The present paper briefly reviews the overall growth in world consumption* and changes in the three main areas which today represent the mature economies or industrialised areas, i. e. ,Europe, the United States and Japan. Trends in overall consumption are determined by the demands for the individual uses for lead and zinc. The changes in patterns of use in the industrialised areas - individually and collectively - and reasons for the changes are also considered. LONG TERM TRENDS - 1900-1984 The World Picture Since the beginning of the 20th century the world consumption of lead (3.9 million tonnes in 1984) has grown almost fourfold and that of zinc (4.7 million tonnes in 1984) is almost eleven times greater than it was in 1900. The long-term trend has been one of continuing expansion for both. metals although the pattern has been severely disturbed at certain periods, for example in the years immediately following the two world wars and at times of marked recessions in industrialised areas. Apart from such major setbacks, new levels of consumption have been established regularly every few years. Recently, however, consumption has not really grown and with only a slow and partial recovery in world industrial activity at present, there is no indication that the peak consumptions of 4.2 million tonnes of lead, set in 1979, and 4.8 million tonnes of zinc (1973) will be exceeded in the near future. The growth in world lead and zinc consumption since 1900 is shown in Figure 1 (which includes changes in copper and aluminium for comparison). Overall growth over the period 1900-1984 has been about two percent a year for lead and about three percent for zinc (annual growth for copper has also been about three percent). Increases in tonnage consumption and growth rates by decade for lead and zinc are summarised in Table I. However, the growth rates by decade sometimes conceal very large individual annual increases and decreases. For example, in 1975 lead consumption fell by 13 percent and zinc consumption by 22 percent compared to 1974. In 1976 consumption of lead and zinc rose by 12 percent and 18 percent respectively. The years when consumption 'landmarks' (ie one, two, three and four million tonnes) were first reached are shown on Table 2. Clearly, the pattern of shorter periods being required to attain each extra million tonnes of consumption was broken in the 1970's. The consumption of zinc overtook that of lead for the first time in 1940, and since 1946 has always been at a higher level. Trends in industrialised areas The two key industrialised areas at the beginning of the 20th century were Europe and the United States which between them accounted for some 95 percent of world lead consumption and 98 percent of zinc consumption. Figures 2 and 3 show the growth in lead and zinc consumption, and Figures 4 and 5 the percentage shares for each area since 1900. Europe has usually been the major user of lead except for some years in the 1920fs, most of the 40's and early 50's when consumption in the United States was larger. In 1900, Europe accounted for about 64 percent of world lead consumption and the United States just over 30 percent. Currently, Europe takes about 40 percent of world consumption and the

Jan 1, 1986

By A. H. Leuschner, P. J. Kruger, J. Kruger

INTRODUCTION This paper deals with some practical aspects of the use and interpretation of dosimetric methods for assessing the exposure of workers to natural uranium. Consideration must be given not only to the scientific value of the method of dosimetry, but also to the practicality of the method in the particular working environment. It is generally accepted (IAEA, 1976) that uranium does not present a hazard during the mining and extraction processes up to the final concentration stage, that is precipitation as ADU or calcining to the oxide. Further processing (e.g. conversion to oxides, fluorides, etc.) is generally associated with the nuclear industry. It is customary for uranium processing facilities to be managed according to industrial norms rather than according to those applied for the purpose of radiation protection. This is mainly because of the large quantity of material to be processed and the fact that uranium is considered to be of a low radiotoxicity. Although ventilation is used to some extent, provision is not made for the same level of protection as would be required in a radiochemical facility. It is typical in such a plant to find that the process itself may be enclosed and ventilated, but the ventilation is inadequate to cope with an accidental release of material. The working environment is poorly ventilated, sometimes only by natural ventilation, and one frequently finds areas with high airborne dust levels, designated as mandatory respirator areas. Protection of personnel is dependent on personal protective equipment. Radiation protection is not of prime concern and personnel are not specifically trained in this subject. It is in this type of environment that acceptable monitoring procedures and personnel dosimetry must be established. The effectiveness and practical application of the dosimetry must also be judged against this working environment. DOSIMETRIC TECHNIQUES The methods available for assessing personnel exposure, whether it be in terms of chemical or radiological hazard, include urinalysis, faecal analysis and [in vivo] monitoring. Faecal analysis does not present itself easily as a method for routine use. Techniques for [in vivo] monitoring have been developed recently and as expensive instrumentation is required, it is not generally available. That leaves urinalysis as a dosimetric technique for routine use, and it is probably for this reason that urinalysis is still widely used. Guidelines for the interpretation of urinalysis results, as originally provided by Neuman (Neuman, 1950), are still used in practice, even though it has become clear that this method has severe limitations as regards the assessment of the dose as a result of the intake of class W or class Y compounds (Alexander, 1974). Typically a level of 300 µg [U/C] urine can serve as an indicator of an acute exposure (above which chemical damage to the kidneys may occur) and a level of 100 µg [U/C ] urine can serve as an indicator for an investigation. Such levels are determined and are used in conjunction with several factors, such as mode of intake (ingestion or inhalation), solubility of compound (D, W or Y), means of intake (acute or chronic), environmental monitoring results and frequency of urine sampling. Since the ICRP concept for internal radiation limitation changed from that of the critical organ, i.e. the single organ of greatest significance under the circumstances, to that of effective dose equivalent, i.e. account being taken of the total risk due to the exposure of all tissue, the maximum permissible organ burden (MPOB) was replaced as secondary dose limit by the annual limit on intake (ALI) (ICRP, 1977). The ALI values are calculated from the committed dose equivalents of the various organs, and are used to determine organ burdens, which are then used to interpret the dosimetric results. Using the ICRP model (ICRP, 1979), a comprehensive calculation was made by Johnson (Johnson, 1980), giving organ burdens and excretion data in terms of intake for acute and chronic exposures for different categories of uranium compounds. The question arises as to what extent the direct measurement of intake can be utilised as a method of dosimetry. This will require a method of personal intake measurement for each individual worker, with both ingestion and inhalation being taken into account. A measurement of

Jan 1, 1981

By William F. Brandom

INTRODUCTION Cross, et al. (1974), produced a retrospective study of standard setting for underground miners. This report had two distinct components; i) criteria of importance for the protection of the miners, and ii) economic considerations for standard setting. The methods for setting radiation safety standards reviewed were: dose calculations and consensus methods; epidemiology; pathology; bioassay; animal experiments; sputum cytology; chromosome aberrations; and, the Mantel-Bryan Model. By looking back, the authors intended to enable officials to look ahead in making future decisions based on reasonable conclusions. Now it may be time to consider underground miners' protection from another perspective: are there miners who may be especially susceptible to toxic environments?; and if so, are there any biomedical assays that might be indicative of exceptional sensitivities to toxic substances? The human population is genetically very heterogeneous. The data of Saccomanno, et al. (1973), reveal great variability in individual response to radon daughter exposure and only a small portion of the miner population subject to toxic inhalants develop squamous cell metaplasia (Saccomanno, et al., 1970). The majority of the miner population is either not susceptible or is resistant to the toxic agents. This information suggests the existence of a small subpopulation with increased sensitivity or reduced resistance and underscores the need for indicators from biomedical assays that might prove of value for the detection of such individuals. The heightened awareness of the contribution of pollutants in the environment for the potential induction of mutations and carcinogenesis lead to a profusion of short-term bioassays to circumvent the high cost and time-consuming large toxicity animal studies. Over 100 bioassays across taxa from microbes to man are at various stages of use or development (Hollstein, et al., 1979). Less than a dozen tests currently offer early promise for application to[ in vivo] effect studies of man. Many are still in early development, lack the sensitivity needed for a retrospective or prospective study at current permissible exposures, are impractical to conduct in the field, or are not cost effective. The purpose of this paper is to review some of the bioassays that may now, or in the near term, prove applicable for the detection of individual underground miners with increased susceptibility to toxic agents. Throughout this statement, it is assumed that any single test may give false negatives or false positives and, therefore, a tier of tests should be investigated. The possible tests are in various stages of development; some tests better proven than others with a firmer data base and, therefore, with greater probability of usefulness. Some of the less proven assays are not ruled out if they have practical or theoretical promise as indicators. Table I summarizes the assays critiqued for their potential to monitor the effects of [in vivo] exposure to genotoxic substances. POTENTIAL INDICATORS OF HIGHLY SENSITIVE MINERS Assays of Body Fluids It is desirable to have data on the agent(s) to which subjects are exposed when humans are monitored by biomedical effects. Obviously, to varying intensity, the underground mining environments are monitored for radon daughters and it is recognized that the miners are also exposed to other pollutants, most notably, uranium ore dust and diesel fumes. Further testing for the metabolites of the pollutants can be done on body fluid, urine. [High Performance Liquid Chromatography (HPLC)]: This is a very sensitive method for the detection of mutagenic metabolites in urine. The urine is treated with the enzyme sulfatase and beta-glucuronidase to permit identification of substances that are made nonmutagenic by conjugation as glucuronides. The sample is then passed through an XAD-2 resin column and the absorbed organic molecules eluted with acetone. The sample is then split and evaporated to 1 ml and used for direct chemical analysis using HPLC. One drawback to the test is the inability to measure cumulative exposure, but multiple samples can be obtained and comparison to baseline (control) and exposure samples can reveal qualitative differences as a consequence of exposure to mutagens. [The Ames/Salmonella Microbiological Assay]: The Ames/Salmonella microbiological mutagen test is the most extensively used short-term bioassay, with over 2,600 chemicals having undergone testing by this method (Hollstein, et al., 1979). The method, thoroughly worked out and tested for 10 years, consists of taking the second split urine sample from the HPLC preparation, evaporating to dryness and dissolving in dimethylsulfoxide (DMSO). The sample is then applied directly to

Jan 1, 1981

By L. Borsch

Geochemical laboratories are commonly criticized by geologists about poor analytical reproducibility and erratic anomaly patterns, especially when gold and trace metals from resistant minerals are reported. Geochemical analysis in mineral exploration is a compromise between high productivity on the one hand, imposed by large numbers of samples, and analytical precision and accuracy on the other. However, the physical properties of resistant minerals, such as cassiterite, gold, beryl, chromite, zircon and others, interfere with both of these requirements. Therefore, the degree of sample homogeneity that can reasonably be achieved in sampling and sample preparation must be considered. Subsequently, the understanding of its effects on analytical data quality and the consequences on data interpretation will provide a basis for understanding the problems common to exploration as an interdisciplinary science. Complaints about poor and inadequate analytical performance are not confined to exploration geochemistry. They are a common feature in mining and metallurgy and wherever sampling and analysis of "grains" are concerned - the "nugget" or "grain size effect." The "grain size" effect Poor analytical reproducibility is normal for gold and a well-defined group of other elements usually found in resistant placer minerals. Those who use and interpret geochemical data must realize and appreciate the chemical, the physicochemical, the physical and the mineralogical properties of the elements and their minerals. Especially for the "placer" minerals and their elements, such comprehensive interpretation is crucial. The most important factor to consider is the behavior of a mineral and its metal component(s) during weathering and their integration into the sampled medium, in exploration mostly sediments and soils. (Data interpretation for samples of water, gas, to a certain extent rock, follows different patterns.) A mineral may be chemically and physically stable or it may easily disintegrate physically or decompose chemically, or any combination of such processes, at varying degrees. The breakdown products, in turn, may or may not, interreact with the environment. If the nature of an element or a mineral predestines it for a heterogenous distribution in the sample medium, then nature, size and number of grains likely to occur should be considered in relation to the sample portion taken for analysis. This allows the estimation of their effect on analytical precision and accuracy. Elaborate and sophisticated statistical calculations exist on this subject. But these approaches do not cope with the complexity of the natural surface environment. The miner alogical, chemical and environmental behavior of elements and minerals can be estimated but not calculated. However, the mineral grain sizes and their influence on analytical precision can be precisely calculated if certain conditions, assumptions and idealizations are made. If the geochemical and mineralogical characteristics of minerals and elements are understood, such calculations demonstrate the grain (or nugget) effects that mineral properties and (geo)chemical behavior of minerals and elements cause on the precision and accuracy of geochemical analysis through their influence on sample homogeneity. Two other factors that influence the sample homogeneity and the nugget effect are the efficiency of sample preparation and the sample portion taken for analysis. In this way, certain element- or mineral-specific parameters can be established as a guide for the sampling program. The information, for example, may assist in determining sampling procedures in the field, especially the sample weight to be taken for "representative samples." Also, it may help assess whether analytical data, as provided by the laboratory, are acceptable. Finally, it may help determine the approach in data interpretation. However, all such simplified calculations are based on idealized, that is, unreal assumptions and conditions. As such, they represent one extreme end on the scale of probabilities. The reality is found somewhere away from this extreme, towards homogeneity. An example from a study of an eluvial gold prospect may be given for illustration: •Original sample weight: 20 kg (44 lbs) of rock gravel, crushed and ground to -0.18 mm (-80 mesh). •Au content: 20 grains of Au, average size of about 0.5 mm3 (0.03 cu in.) each = 7.5 mg each, making a total of about 150 mg Au in the sample = 7.5 ppm Au. Assumptions •Au occurs in the sample as free, discrete grains only. •Not more than one grain, if any, goes into each sample split (analyte) portion (20 grains of 7.5 mg Au each). •Analysis of original rock sample: 100 g sample for analysis, 20 kg/100 g = 200 samples 20 samples with 1 grain each: result, - 75 ppm Au. 180 samples with no grain: result, 0 ppm Au chances 1:9 •10 g sample for analysis:

Jan 1, 1996

By P. Sander, M. Spiegl, J. Reilly, A. Van Droogenbroeck

Although the outdated idea of calculating risk as the deterministic product of its likelihood and impact is not entirely a thing of the past, a multitude of organizations have adopted the usage of probabilistic methods for risk analysis, as they better reflect the inherent uncertainty of cost and risk estimates with ranges. But are these advancements sufficient in a complex environment such as tunnelling projects, where inadequate modelling of cost and risk can result in estimate discrepancies that run into millions of dollars? This paper explores two advanced probabilistic modelling techniques for tunnelling projects. The first one demonstrates how the cost and schedule uncertainty related to changes in excavation and support classes can be modelled with correlated variables. The second example models the risk related to explosive ordnance clearance on construction sites using a probabilistic event tree.

Dec 1, 2022

By T. D. Murphy

In the fall of 1988 it became evident that the accuracy of sulfur forecasts for Monterey Coal's No.1 Mine needed to be improved. In addition, it became necessary to predict if any individual train shipments during a month would exceed a contract sulfur limit. The challenge was to develop a forecasting process that would take into account the variability of the coal in the ground as well as the difference between laboratory and preparation plant sulfur reduction efficiency, and the effects of mining coal with multiple units. This paper describes how geostatistics and simulation techniques were used to meet this challenge.

Jan 1, 1992

By J. R. Palmes

Flocculation of coal fines with varying degrees of wettability was studied under well defined hydrodynamic conditions. In this study, three coal samples were tested with three different flocculant types. The results revealed that flocculation depends strongly on both the coal surface properties and the type of flocculant used. A hydrophobic flocculant was found to be effective for hydrophobic and slightly oxidized coal, a semihydrophobic flocculant was found to flocculate, to different extents, all of the samples except the oxidized cool, and polyacrylimide flocculated all of the coals, which is a clear indication of its insensitivity towards coal wettability.

Jan 1, 1994

By L. J. Laughlin

The majority of non-drive conveyor pulleys use rotating shafts, and typical idler rolls use non-rotating shafts, even though both products are used to support and guide the conveyor belt and its load. This paper will explore and compare the requirements for rotating and non-rotating shaft designs and the impact of that design on the product. Additionally, it will explore how the “roller” bearing types (deep groove ball, tapered, or spherical) affect these designs.

Jan 1, 2003

By Robert P. Mahoney, William J. Roe

Polymers of a wide variety of composition are used in coal and mineral beneficiation. Applications include flocculation and coagulation in thickeners, filtration enhancement, mill scale control, dust control, ore leaching improvement, and pond management. The proper chemistry of the polymer is determined by many factors, including the nature of the process, mineral type, and respective performance requirements. This paper provides an overview of the various current applications of polymers in mineral processing, and a description of the applicable polymer chemistries which find utility in these applications. Examples of structure/performance relationships are discussed.

Jan 1, 1994

By K. G. Sutterer, R. J. Sweigard, U. Graham, T. C. Hopkins

The prevalent use of coal combustion byproducts in engineering applications has been with Class C and Class F fly ash as admixtures in structural concrete. But, the use of fly ash and bottom ash byproducts from modern desulfurization processes is receiving increased attention. The University of Kentucky has been conducting research into civil- and mining-engineering applications of these products. The studies have included extensive investigation of the geomechanical behavior of the materials and the effect of mineralogy on this behavior. These studies indicate important mineralogical considerations in the selection of materials for a specific application and highlight the importance of quality control before and during usage on specific projects.

Jan 1, 1998

By C. R. Euston, B. T. Field, W. E. Lindquist

Pyroprocessing applications in the minerals industry range from low-temperature drying to high-temperature reactions. Material characteristics and process requirements range over a very broad spectrum and can confuse plant engineers trying to select a pyroprocessirtg system for their plant. This paper examines the important process variables and offers empirical guidelines to assist in a user's overall process evaluation.

Jan 1, 2000

By Keiichi Fujita, Michio Miyoshi, Hisashi Miyazaki

In the construction of "Hamacho" subway station (Tokyo Metropolitan Rapid Transit), in order to minimize ground surface settlement, the pipe-roof method was employed as an auxiliary measure when removing the portion between two parallel shield tunnels to form one large tunnel for the station. 14 steel pipes (dia.1,219.2mm, length 75m) were driven in horizontally so as to cover tunnels and support heavy and extremely soft covering soil and surface structures. Procedures of temporary supporting, excavation under compressed air, reinforcing, concreting, etc., and some comparisons with conventional methods are described.

Jan 1, 1979

By D. E. Ranta, William B. Ryan, Ronald W. May

The Lower Cretaceous McMurray Formation in northern Alberta contains bituminous sands interbedded with other sediments which form the reject encountered during mining operations. Grade prediction is based on a combination of geological interpretation, computer modelling and past mining experience. In addition to estimates for ore, an accurate estimate of "waste" or "reject," are required for Mine Planning. This study investigates the ability of point-kriging using geostatistics, to augment the existing data base of drill-holes in a study area on Syncrude's leases. This approach enables the assessment of potential "worst" case - "best" case scenarios within the context of Mine Planning.

Jan 1, 1992

By Joseph Cervik

Methane drainage methods can be broadly classified as surface or underground. Surface methods make use of vertical and slant holes. The underground method discussed in the present paper involves horizontal drilling from shaft bottoms and from locations along the periphery of mines. Every foot of hole drilled in coal from under- ground locations is productive and gas flows increase as hole length increases. Therefore, underground techniques have a great potential for producing large-volume flows of methane. Pumps to dewater the horizontal holes are not necessary because gas pressure forces the water out of the hole. Methane can be recovered through the use of a simple and inexpensive gas-water separator. Hydraulic fracturing, which has been used successfully to stimulate gas flows from vertical holes, has not proved practical in the case of horizontal holes.

Jan 1, 1980