Search Documents

By R. Q. Honaker, D. P. Patil, A. Sirkeci

Because of increasing production of fine coal during mining over the past century and because of inefficient fine-coal recovery technologies, a vast reserve of high-quality coal now exists in refuse ponds. A novel finecoal circuit, consisting of a hindered-bed classifier, an enhanced gravity concentrator and a flotation column, was evaluated for the recovery of fine coal from refuse ponds. The treatment of a pond derived from Pittsburgh No. 8 seam coal resulted in the production of a premium fuel containing less than 5% ash and a calorific value of about 30,170 kJ/kg with 60% mass yield. Results from the treatment of two refuse pond materials are presented in this paper.

Jan 1, 2002

By S. Chander, A. Briceno

The properties of surface films on pyrite have been studied through electrochemical techniques of cyclic voltammetry and AC impedance, measurements. The characteristics of the surface films depend on the conditions of oxidation and the source of pyrite. At potentials near 0.0 V, some pyrites have large values of polarization resistance, showing a certain degree of passivity. Some pyrites show more passivation than others, however. On oxidation, meta- stable phases of Fe(OH)2 and Fe(OH)3 form that transform to more stable phases on aging. The growth of surface films near the corrosion potential of pyrite follows a linear kinetics that is attributed to a chemical (or an electrochemical) reaction as the rate determining step. The surface film is considered to be a hydroxide or an oxide because it is hydrophilic. This study has also demonstrated that AC impedance ,measurements can be used to study the growth characteristics of films at mineral/solution interfaces.

Jan 1, 1988

By Richard W. Hornung, Steven Samuels

A great amount of work in recent years has been devoted to refining older survivorship models, e.g. life tables, and developing newer ones, e.g. Cox regression. In this paper, these models are applied to data from an epidemiological study of uranium miners in four western states conducted by the U.S. Public Health Service. One of the principal problems addressed in this paper concerns the appropriateness of using cumulative dose as the measure of radiation exposure. An alternative is considered that incorporates dose rate into the model. This procedure does not implicity assume that equal cumulative doses produce the same lung cancer mortality, but instead considers the amount of time in which each miner's dose was accumulated. Results of the statistical analysis indicate that dose rate is a significant factor at higher cumulative dose levels, with lower dose rate apparently more damaging than higher dose rate. The shape of the dose response curve is curvilinear at higher dose levels. No interaction was found between smoking and radiation exposure on a multiplicative or relative scale.

Jan 1, 1981

By D. III Earley, R. L. Blake

The Bureau of Mines is investigating the potential for in situ mining (ISM) of gold and silver mineralization. This preliminary study examined samples from several types of deposits. It used light optical microscopy and the electron microprobe to characterize the ore and gangue minerals and textural features of these samples. This included the spacial relations between the target minerals and likely natural fluid channel ways. Low-grade disseminated deposit types from the western US were found to contain fracture- hosted or matrix-hosted gold and silver minerals, some of which are encapsulated by quartz or pyrite. Successful ISM application to gold and silver deposits needs this data in order to understand potential problems of the lixiviant reaching the ore minerals.

Jan 1, 1991

By B. A. Carbon

Western Australia is the largest state in Australia with an area one and three quarter times the size of Texas. Most of the State is desert or semi-desert, and only the southwest corner is heavily populated. The State has a population of one and a half million people, and one million of these live in and around the city of Perth. Perth is located on the narrow Swan Coastal Plain and is flanked by the Indian Ocean and the Darling Plateau. The Darling Plateau is an ancient peneplain rising some 300 metres above sea level, and forms an important resource base for the population. The Darling Plateau is old, having been formed some 200 million years ago, and its soils are deeply weathered. The parent materials were granite and gneis which have broken down to form lateritic gravels, overlying dense kaolinitic clays. Some 30 million years ago, in the Tertiary period, a sub - tropical climate prevailed. Appropriate conditions of moisture, temperature and drainage led to extensive laterisation. Some of the laterite contains bauxite of mineable quality. Some 1.9 million hectares of the south-west of Western Australia is covered by eucalypt forests. Threequarters of this forest is referred to as "Jarrah

Jan 1, 1984

By David McGregor, Ashoke SenGupta, Jerry Darlington

The stability of bentonite clay suspensions against flocculation in the presence of certain anionic polymers was investigated. These polymers included a purified sodium lignosulfonate, a sodium oxylignosulfonate, a potassium salt of humic acid, and a sodium polyacrylate. The polymers differed from one another in molecular weight as well as in carboxylic, phenolic, and sulfonate group contents. The scope of this study is in evaluating the extent of thinning achievable in a bentonite clay suspension in the presence of these anionic polymers under varying electrolyte concentration, presumably as a result of deflocculation of the clay platelets by the polymers. Under certain conditions of polymer dosage and electrolyte concentration, the lignosulfonate seemed to have flocculated the clay suspension, while the other polymers served fairly well as a deflocculating/dispersing agent. The lignosulfonate, however, showed some deflocculating ability when the electrolyte concentration of the suspending medium (water) was increased by adding sodium chloride to the clay suspension. Among the four polymers tested, the polyacrylate was found to be the most effective in deflocculating clay particles, followed by the humate and the oxylignosulfonate.

Jan 1, 2003

By R. Y. Wan

Newmont Gold has advantageously used the capabilities of mineral oxidizing bacteria to develop a process for the pretreatment of low-grade sulfidic and carbonaceous-sulfidic refractory gold ores. The biooxidation process results in the oxidation of the sulfidic minerals with increased exposure of gold for subsequent gold recovery. The biooxidized carbonaceous-sulfidic ores cannot be heap leached with cyanide because of the preg-robbing characteristics of the carbonaceous matter in the ores. Therefore, an alternative heapleach process using ammonium thiosulfate was developed to extract gold from these preg-robbing bioaxidized ores. The ammonium thiosulfate leach process was successfully applied in both laboratory and pilot plant tests. Satisfactory test results were achieved, encouraging the continuation of process development.

Jan 1, 1997

By G. T. Adel

Hindered-bed separators are often used in the minerals processing industry to classify particles according to size and density. A new technology, known as the Eriez CrossFlow, was recently developed to overcome some of the limitations associated with hydraulic separators. The innovative feature of this unit is a novel feed presentation system that improves separation efficiency and capacity. In the present work, a detailed process engineering evaluation was conducted to determine the basis for the improved performance of this unit. The evaluation included controlled separation tests using well-characterized feeds, particle and liquid tracer experiments and mathematical modeling studies. Data obtained from this work show that the new separator is capable of maintaining good separation efficiencies at higher solid feed rates than traditional designs due to improved hydrodynamics in the separation zone. This paper reviews the operating principle of the Eriez CrossFlow separator, discusses the results of the tracer experiments and modeling studies and presents test data obtained from recent laboratory and plant trials. Key words: Size classification, CrossFlow separator, Hindered-bed separator, Hydraulic separator

Jan 1, 2003

By A. L. Mular

Steady-state material balances calculated from data measured at various locations around process units are useful for many purposes, such as metallurgical accounting, on-line control, and the development of mathematical models. Often it is possible to calculate material balances by several independent procedures when excess measurement information, i.e., redundant data, is available. Clearly, if the data were collected without measurement errors, a theoretical condition never found in practice, all material balances calculated from redundant data would be in agreement. The real situation is that error exists in practical measurements, so that the results of material balances determined from available optional procedures differ. Consequently, best fit computational procedures to improve the material balances by taking measurement errors into account have been formulated. Such procedures can be used also to judge whether measurements are grossly in error due to either faulty observations or defective data sensing devices. A variety of mathematical techniques are available which serve to adjust raw data. The adjusted data permit mass balancing that does not depend on the computational method. To illustrate the need for an adjustment procedure, Table 1 shows a raw data set acquired around the Brenda Mines Ltd. No. 4 grinding circuit shown schematically in Fig. 1. At least seven optional ways to calculate a circulating load ratio may be employed. These are shown in Table 2 where, depending upon the calculation [ ]

Jan 1, 1979

By E. D. Attanasi

Exploration for non-fuel minerals has declined since 1988 as recessionary pressures have slowed growth in the industrialized economies. By most accounts, however, 1990 expenditures were still significantly greater than the low levels experienced in the mid-1980s. The Persian Gulf crisis introduced instability in energy prices and greater uncertainty into an already cloudy economic picture. As 1990 unfolded, the US savings and loan problems spread to the commercial banking system, leading to the failure of several major US commercial banks. The Japanese stock market also suffered significant losses as Japan's Central Bank raised interest rates. The Soviet Union experienced shortages of food and other basic items. Its government faces resistance to changes leading to a market economy. Individual Soviet republics also are seeking more control of their own destiny. The cost of German reunification, in terms of the capital required to bring the east's infrastructure and industrial base to western standards, also appears to have been underestimated.

Jan 1, 1991

By Stephen R. Pogorski, Nicholas Busigin, Colin R. Phillips

The movement of radon away from its source in porous media is determined by two key parameters: the fraction of the total radon formed which enters the intergranular pore spaces, termed the emanation coefficient, and the transport processes which exist in these pores such as diffusion and convection. The first parameter, the emanation coefficient, is of primary importance since it is a measure of the actual amount of radon which is free to migrate within the media. The effects of particle size and radium concentration on the emanation coefficient were examined using a quartz-pebble conglomerate ore from the Elliot Lake mining district of Ontario. It was found that the smallest particle size examined (<74 µm) had the highest radium concentration and contributed the most to the radon emanation. A one-to-one correspondence between radium concentrations for the various particle size fractions and radon emanation was not observed. Samples were examined using scanning electron microscopy and very small particulates were observed to be present on the particle surfaces. When these very small particulates were removed from the host particle surfaces by rinsing, the radon emanation decreased by a factor of 17. This result indicates that most of the emanation comes from the very small particles. The effect of moisture on the emanation coefficient was examined qualitatively and a trend of increased radon release with moisture content was noted.

Jan 1, 1981

By C. Babbitt, J. O’Green, N. I. Jayaraman

In many mines, dust-laden air from an entry being driven by a continuous miner will contaminate the intake air to the roof bolter operator and other downwind personnel. Through a US Bureau of Mines (USBM) contract, Foster-Miller Inc. has evaluated several control techniques to reduce the respirable dust exposures of downwind personnel. One fan and tubing technique consisted of bypassing the miner-generated dust directly to the section return. The results of the evaluation of this technique revealed that reductions in dust concentrations of 90% or more can be achieved at downwind roof bolter locations. A second method was to clean the dusty air from the upwind continuous miner by using a dust collector. The cleaned air was then supplied to the bolter through collapsible tubing. An underground evaluation showed reductions of 82% to 96% when the dust collector was operating. A third method was to reduce the quantity of dust contributed by the miner to the return airstream. A water-powered scrubber was installed over the throat area of the continuous miner. More than 1.18 m3/s (2500 cfm) of dusty air moved through five tubes with dust collection efficiency exceeding 75%. Underground evaluation results showed that return dust concentrations were reduced by about 60%. This paper discusses the ventilation and dust control techniques used for personnel downwind of the continuous miner.

Jan 1, 1987

By K. Holmberg, D. Herriot

This paper by Mr. McIvor is yet another contribution to the eternal controversy surrounding the benefits, or otherwise, of high circulating loads in closed circuit grinding. Throughout the paper it is difficult to establish whether the author is referring to effects relating to the mill, classifier, or to the overall circuit. Table 1 is put forward as indicating the advantage of operating at high circulating loads. From the two (it would be interesting to see more) product sizing points provided in each case, the conclusions to be drawn are that cases one and two have very similar size analyses. The third case, however, indicates a much flatter curve, that is to say, higher fines production and a very wide spread of size ranges. If the objective of this circuit is to provide a closely sized product with minimum overground slimes to the downstream process, then it would appear to be the less "efficient" by far. No data is given for product pulp densities either. The term "efficiency" should never be used without a careful and clear definition. In this case, "efficiency" is used to express an apparent percentage reduction in operating work index (Bond) from the measured "standard" at 250% circulating load operation. The Bond calculation is itself based upon

Jan 1, 1990

By N. Finkelstein, D. A. Hinckfuss

The large and compact but simple Bougainville Copper Limited flotation circuit has been in operation for 3-1/2 years. Discussion of problem areas encountered since start-up and remedies that have been implemented or proposed, form the main basis of this paper. Full cur- rent operational data is also provided.

Jan 1, 1976

By W. L. Fourney, D. C. Holloway, J. W. Dally

Introduction Improvements in the process of rock excavation by blasting involves better control of one or more phases of the fracture process immediately after detonating the ex- plosive charge. Total control of the process involves individual control of (1) The number of fracture planes. (2) The crack initiation sites. (3) The direction of crack propagation (usually radial). (4) The stress field driving the fracture front. Fracture plane control is usually accomplished today by using the smooth wall blasting method; however, investigations by the authors (1) indicate several areas where this method could be improved. These improvements include: a) generation of stress concentration factors at the location of the initiation sites; b) protection of the remaining region of the borehole wall to inhibit initiation of any cracks not associated with the fracture plane and fragmentation pattern; c) limit peak detonation pressures to avoid borehole crushing and maintain by stemming residual gas pressure in the bore- hole during the crack propagation period. This paper describes experiments con- ducted with a charge holding device fabricated from thin-wall steel tubing which was partially slit at fracture locations. The tube lined the bore-hole in laboratory tests to simulate smooth wall blasting. Results showed close control could be achieved relative to both the number and the location of the fracture initiation sites.

Jan 1, 1977

By G. Reed Marchant

In 1967 the US Congress passed the "Clean Air Act." This act was amended in 1970. As a result it soon became obvious that American industries were going to have to make significant changes in their methods of operation to be able to comply with quickly developing federal regulations. One of the first regulations developed was on sulfur dioxide. For this reason, the nonferrous smelting industry was immediately affected by these new regulations. This is true because the smelting process produces sulfur dioxide as a natural product of combustion when the sulfur-bearing ore is oxidized to purify the metal. The federal government&apos;s approach for setting standards included public hearings at which government, industry, and private citizens were allowed to make comments. For this reason, it was apparent to Kennecott&apos;s Metal Mining Div. that it was desirable to make a maximum effort in working with the agency to see that correct input was provided at the hearings to assist the government in setting fair and realistic standards. It was also obvious that more complete monitoring would be required. It soon became apparent that the efforts required input from many levels of the corporation from the chief executive to the plant operators. In order to accomplish both the administrative and the technical needs, an organization was needed that could respond quickly to these needs, obtain information from diverse sources, and bring it to focus in an organized approach to the problem.

Jan 1, 1979

By J. A. Finch, J. Yiantatos, A. R. Laplante

This paper re-examines the mixing conditions in the collection zone of flotation columns. These have in the past been characterized with a single uniaxial dispersion coefficient, E. The relationship between E and column diameter, Dc, is examined based on residence time distributions (RTDs) in columns of Dc ranging from 5.lcm to 184cm. Results agree with published correlations in chemical engineering, i.e. E a Dc &apos;" , Data explain why pilot columns display significant upgrading between the feed level and the interface, whereas plant columns do not. It also suggests that, for plant columns, the full collection zone (up to the interface) can be considered when calculating the residence time. A mathematical model considering two regions of different mixing was compared to the single E model. Both models adequately fitted measured age distributions inside the column and overall RTDs. Measured and simulated mixing characteristics are compared to those of flotation banks, using a tanks-in-series approach; banks of comparable mixing to columns are identified.

Jan 1, 1988

By Tso-Min Shih, Ching-Hua Liu, Chung-Jen Lin, Hsi-Chiang Fang

This paper presented herein, describe the special design of an open type coal dust explosion apparatus and the laboratory works for investigating the effectiveness of the parameters on coal dust explosion and the prevention of the propagation of the coal dust explosion flame. Coal sample which were taken from the San-Ying collieries, were passed through the process of crushing ,grinding and screening to get the required particle size, ranged from 40 mesh to 200 mesh under size for testing purpose, the rock dust spreaded on the surface of coal dust and water mixed with coal dusts were employed for preventing the coal dust explosion and the propagation of the explosion flame.

Jan 1, 1991

By H. Peter Knudsen

Karst hosted lignite deposits are characterized by variable thickness of lignite that was deposited in depressions in the karst topography and by the variable extent and shape of the lignite pods. Since the lignite to be mined will feed a mine mouth generating plant, an extremely important criteria in the mine plan is to assure continuous feed to the plant. The variability in both the extent of the pods and the thickness of the lignite within the pods must be taken into account in any mine design in order to quantify the risk that an area being developed will have enough lignite to feed the plant for the specified period. Indicator kriging was used to create a model of lignite thickness of the deposit. Pod boundaries were determined from the indicator kriging model by two methods. First, contour maps showing the probability that the lignite is above a minimum mining thickness were prepared. Using these maps the mine planning engineer can determine either conservative or optimistic boundaries. The second method recognized that the most costly error that can be made in the mine plan is to run out of lignite. Thus, a loss function was determined from the costs of overestimation and underestimation. Using this function, the probability that minimizes the risks of overestimation versus underestimation was calculated.

Jan 1, 1989

By J. K. Whyatt

A microcomputer controlled data acquisition system has been developed for automatic monitoring of underground instrumentation from a remote location. The system has been used extensively by Spokane Research Center personnel for monitoring rock instrumentation in shafts, drifts, and stopes in hardrock and coal mines, especially where instrument access is limited. Ruggedness was a major consideration in designing the underground portion of the system and it has performed satisfactorily under extreme environmental conditions, including temperatures to 1100 F, 100% humidity, and falling water. The major advantage of the system is that it multiplexes the data from 16 channels through a single twisted pair cable to the receiver, significantly reducing cabling requirements. This receiving station can be as far as 8,000 ft from the instruments without the addition of line drivers. The receiver maintains a data buffer with the latest scans, which is periodical 1 y accessed by a micro- computer, either locally or through a modem, that automatically records and reduces the data. Utilities allow on-site plotting of data and uploading of data to mainframe computers.

Jan 1, 1986