Search Documents

By F. N. F. le Roux

This paper describes the method used for excavating the upper 33m of emergency access shaft E2 for the underground single track tunnel running between Park and Rosebank station of the Gautrain Rapid Rail System. The soil was decomposed shale and diabase from the Witwatersrand Supergroup. The location was in the car park of The Wilds (a public park) in Johannesburg. The method proved very simple and required less complex plant and equipment than normal when excavating the shallow soil sections in shafts. It involves driving steel sheets ahead of the shaft sump into the soils and then excavating inside the ?tub? created by the sheets whilst supporting the sheets above with regularly spaced circular Steel Rings. It is the intent of this paper to discuss the method and design approach to the method. This will be done at the hand of experiences at E2 shaft..

Jan 1, 2009

By J. Gholamnejad

In open pit mine planning and design, push back mine sequencing is widely used for long-term production planning. In push back design, a series of nested pits is generated and then considered as possible push backs with regard to the minimum push back width requirements. These nested pits are produced by parameterizing on one economic parameter like commodity price, mining or processing cost, stripping ratio, etc. The most important characterization of these push backs is that the innermost push back has the highest value per ton, the second innermost push back has the second highest value per ton, and so on. These nested pits are generated based on the best estimates of grade within a representation of the orebody in a three-dimensional matrix form. Therefore, the inherent uncertainty associated with reserve estimation (for our discussion, grade uncertainty) is not taken into account when push backs are designed. These methods do not attempt to establish which part of the deposit is likely to be worth most. This paper introduces a new algorithm that incorporates ore grade uncertainty during the pushback design process. The suggested strategy tries to seek to schedule risky blocks later in the extraction sequence. Keywords: open pit mine, push back, ore grade uncertainty.

Jan 1, 2007

By S. Adams, J. R. C. von Holdt, J. L. Broadhurst

Fugitive dust from mineral extraction and processing activities can significantly influence air quality, the environment, and the health and quality of life of workers and surrounding communities. Poor engagement and communication between experts and lay persons, disciplinary silos and polarised viewpoints have made it difficult to develop a holistic understanding of the complex health issues associated with environmental emissions of mine dusts, and consequently to design meaningful and integrated approaches to address such issues. The collaborative Global Challenges Research Fund (GCRF) Mine Dust and Health Network, hosted by Minerals to Metals at the University of Cape Town, serves as a collaborative think-tank to inform research directions within and across disciplines, government policy and regulations, health monitoring programmes at public clinics, industry best practice, community healthcare and impact prevention programmes. It focuses initially on the southern African region, but with the intention to expand to mining-intensive developing countries within the rest of Africa, South America and Asia. This paper outlines the approach and activities of this global transdisciplinary and intersectoral network and presents some of the key outputs and achievements to date. Keywords: Mine dust, Global Challenges Research Fund Mine Dust and Health Network

Jan 1, 2020

By K. Shin

Determining the anisotropy of rocks has in the past been difficult and rarely attempted in engineering practice. Here we have developed a new practical methodology for measuring orthotropic anisotropy that requires only one hollow cylinder specimen to determine the anisotropy of a set, even when the directions of the anisotropic axes are unknown. Autrefois, la détermination de l’anisotropie des roches était difficile et elle a été rarement essayée dans la pratique de l’ingénierie. Voilà c’est nous qui avons mis au point une nouvelle méthodologie pratique pour mesurer le coefficient de conductibilité thermique de l’anisotropie qui exige un seul spécimen du cylindre creux afin de déterminer l’anisotropie d’une série, même si les directions des axes anisotropiques sont inconnues. Früher war die Bestimmung der Anisotropie von Gesteinen ein schwieriges Verfahren, das in der technologischen Praxis nur selten in Angriff genommen wurde. Wir haben hier eine neue praktische Methodik zur Messung der orthotropen Anisotropie entwickelt, bei der nur ein Hohlzylinder an Gesteinsproben benötigt wird, um die Anisotropie einer Reihe von Steinen zu bestimmen, selbst wenn die Richtungen der Anisotropieachsen unbekannt sind.

Jan 1, 2003

By A. S. Macfarlane

The introduction of new technology into mining operations is seen as a strategic necessity by many mining companies, in order to improve safety and to improve operational effectiveness. Many attempts have been made in recent years to introduce new technologies into mining operations in southern Africa. Amongst these are noteworthy successes, as well as some disappointing failures. Often, the reason for failure does not lie with the technology itself, but with the work system into which the technology is introduced. Such failures may come with a significant opportunity cost, and have a detrimental effect on future development, simply because the system has not been adequately engineered, and the risks have not been adequately assessed and managed. This paper examines the reasons for such failures, and proposes a methodology to be followed to ensure successful and sustainable implementation of new technologies, such as to reduce technical and financial risk to the company, and to energize the workforce into ensuring the initial objectives of the project are met. The paper also focuses on the application of appropriate technology, and the development of technological applications which are commensurate with the level of development of the work environment into which it is introduced. The paper therefore focuses on the application of risk management, change management, systems engineering and feasibility analysis as being key elements of a successful and holistic technology implementation programme.

Jan 1, 2001

By U. Sachse

This paper explores a systematic approach for mining decision-makers to use when faced with choosing which method to use for a specific rockpass length. The different excavation methods available in the broad South African mining industry are compared against a number of critical parameters, as applied to rockpasses of varying length. This approach is not meant as a definitive, prescriptive planning tool, but rather as a proposed approach to enable designers and planners to choose the best system to excavate their specific rockpasses

Jan 1, 2005

By J. -P. Chilès

The discrete Gaussian model is a very popular change-of-support model for estimating block grade distributions. It is designed for a stationary random function Z(x) that is regarded as the transform of a stationary random function Y(x) with Gaussian marginal. It is based on an assumption that is not fully true and thus constitutes an approximation to the exact solution. We examine the effect of this approximation on the modelling of the marginal distribution of block values of a lognormal random function. The initial discrete Gaussian model and a variant of that model are considered.

Jan 1, 2014

By L. J. Gardner

Ore pass systems play a critical role in moving broken rock from the workplace to surface, and the integrity of the ore pass excavations is crucial. Over the life of the mine, ore pass integrity deteriorates, which may eventually result in the ore pass no longer being fit for purpose. This paper presents several case studies of successful ore pass rehabilitation exercises.

Jan 1, 2006

By P. J. Rider

Diamond Value Management?s objective is to achieve $/ton revenue improvement across De Beers group mines. The respective %improvement contributions are measured against targets set by each of the operations. Degree of target achievement is measured via a maturity model at each operation. DVM comprises seven elements. It spans several value chain facets and various collaborative projects are conducted under its umbrella. New technologies in De Beers are also evaluated from a DVM perspective.

Jan 1, 2003

By X. Pan

Slag-metal equilibrium experiments were conducted at 1500ºC and1580ºC under 0.03 atm, 0.05 atm and 0.83 atm CO partial pressures using silica and Cr-oxide crucibles. The complex slags belonged toSiO2-CaO-Al2O3-MgO-FeOx-CrOxand the metal phase to the Cr-Fe-C-Si-(S) systems. The carbon saturation of the metal phase was avoided using oxide crucibles and thus the results are pertinent to ferrochromium refining slags and processes. From equilibrium data and thermodynamic calculations, the CrO /(CrO+Cr2O3) ratio in the slag was determined as 0.75, 0.80 and 0.86 under 0.83 atm and 0.05 atm of CO pressure at 1500ºC and 0.03 atm and CO pressure at1580ºC, respectively. The results clearly demonstrated that a higher chromium content of the metal results in higher Cr in the slag, and chromium in slag decreases with increasing SiO2. The results were also sensitive to the crucibles used as these oxide crucibles saturated the slag either with respect to SiO2or Cr-oxides. It was also demonstrated that the relative amount of CrO in the slag was higher when SiO2crucibles were used in accord with thermo-dynamic calculations. Iso-concentration curves for carbon and chromium of the metal phase in equilibrium with the slag were drawn on a pseudo ternary SiO2? (AI2O3+CaO+MgO) ?(Cr2O3+Fe2O3) diagram. The activity coefficients and activities of carbon and chromium of the metal phase were also calculated from the experimental data and available thermodynamics information and were plotted as iso-activity curves in the same pseudo ternary diagram. Keywords: chromium, slag, equilibrium

Jan 1, 2004

By Peter Townsend, Sergei Diachenko, Allan Moss

The Palabora Mining Company has successfully extended the life of its operation by developing a 30,000tpd block cave underground mine below the now closed open pit. The process of transitioning from surface to underground mining has been technically, operationally and managerially challenging. This has been due to a number of factors; in particular, the development of a block cave in a very competent rock mass. The competence of the rock mass is clearly demonstrated in the open pit that preceded the block cave, one of the steepest deep open pit excavations in the world. With cave breakthrough, however, the pit was ?instantaneously? deepened by 400m causing a major failure of the northwest wall involving close to 100Mt of waste material.

Jan 1, 2006

Sulphide minerals, such as pyrite and sphalerite, are leached by ferric sulphate. This reaction produces ferrous sulphate and other dissolved products. The ferrous sulphate is re-oxidized to ferric sulphate by bacteria. These reactions can be written as: [ ] However, in 1964 Silverman and Ehrlich proposed that this is not the only role that is played by bacteria. These researchers proposed that T. ferrooxidans enhances the rate of oxidation of pyrite above that achieved by chemical reaction with ferric sulphate at the same solution conditions. This enhancement in the rate of dissolution was proposed to occur by direct microbiological action, possibly by the extra cellular secretion of an enzymatic oxidant. Since the Silverman and Ehrlich proposal, different authors have made opposing claims concerning the action of T. ferrooxidanson pyrite. This ?direct mechanism? of bacterial dissolution of pyrite can be given by the following reaction: [ ]

Jan 1, 2000

By M. R. Samis

The great variability of mineral and energy prices has motivated some governments to incorporate a windfall profits tax into their mineral taxation regimes. Windfall profits taxes are a means for governments to capture additional mineral revenue when mineral prices are considered higher than some historic level. Governments need to be aware of the effects of such contingent taxes on the exploration, development and operating decisions of mining companies. Mining companies need to be able to calculate the full impact of windfall profits taxes on the economics of their projects. This paper examines the valuation of a multi-phase copper-gold project in the presence of a windfall profits tax. Real options Monte Carlo simulation is used to characterise the different exposures of the mine owner and of the government to the risky cash flow streams that they receive from the project. The results highlight that Monte Carlo simulation paired with the real option valuation method is able to account appropriately for the differing risk exposures, while the traditional discounted cash flow valuation model is not. Our key conclusion for governments and mining companies is that the impact of contingent tax and royalty terms can and should be assessed using advanced valuation techniques, and the results used to improve contract designs under the constraint of actual and perceived fiscal system stability.

Jan 1, 2007

By Conné Spangenberg

Contents ?Introduction ?Metal accounting environment ?Problem statement ?Investigations & Achievements ?Metal Accounting ?Principles ?Standards ?Audits ?Questions

Jan 1, 2005

The modern theory of sampling of particulate minerals essentially consists of a recent generalization of the procedures for applying and calibrating the formula usually known as ?Gy?s Formula? for sampling variance control, in which the central concept is a parameter called the liberation factor l. A model which can be experimentally adjusted was proposed by one of the authors several years ago, based on geostatistical considerations. This new model, which relates the liberation factor to the sizes of the fragments and mineral grains, solves the usual difficulties faced in the past, and permits predictions that are well verified in practice. Unfortunately, an older, arbitrary and less general formula is still widely used. The vast majority of today?s misapplications of Sampling Theory of Particulate Materials can be traced back to the use of this antiquated and generally incorrect model. Following a brief history of the models used for the liberation factor and a description of its main variable, the liberation size, and to illustrate the importance of proper modelling of l, this paper presents demonstrative calculations of the absurdity of the incorrect model using the particular case of gold mineralization as an example, followed by some more positive examples of application.

Jan 1, 2002

Sishen Iron Ore Mine previously used only A-grade material (>60% Fe in situ value) from the pit for beneficiating in the DMS plant to a final product grade of 66% Fe in lump and 65% Fe fine ore. The B-grade (between 50% and 60% Fe) and C-grade material (between 35% and 50% Fe) were stockpiled separately, owing to the inability of the existing DMS plant to beneficiate material at densities higher than 3600 kg/m3. The ability to beneficiate the B-grade material at densities higher than 3600 kg/m3 was evaluated, and air-pulsed jigs were found to be techno-economically feasible and value maximizing. The beneficiation of B-grade material would add to the existing DMS production of 28 Mt/a, with no additional mining cost and only limited costs for the handling of waste and B-material. The objective of the Sishen Expansion Project (SEP), i.e. the jig plant, was to produce 10 Mt/a of saleable product with six modules to the set physical and chemical specifications by 2009. During the start of construction, it was decided to add another two jig modules to the plant to increase production to 13 Mt/a. During commissioning and ramp-up the shortcomings and advantages of the jigs were fully experienced and understood, resulting in many changes to optimize jigging performance..

Jan 1, 2014

By R. M. Lamya

The leaching behaviour of nickel?copper matte in an acidic?copper sulphate solution during the repulping stage at Impala Platinum Refineries has been studied. The base metal recovery process consists of a matte repulping stage prior to a series of pressure leach stages. Therefore, the repulping stage is basically an atmospheric leach stage in which the matte containing mostly Niand Cu is leached in copper-spent electrolyte from the tank house, resulting in dissolution of nickel and precipitation of almost all the copper. To understand the nature of the leaching process during this stage of the operation, the effects of temperature stirring rate and matte particle size on the rate and extent of base metal dissolution and copper rejection from the solution have been investigated. The leaching mechanism of the matte in the investigated system is alsoproposed.

Jan 1, 2006

By A. Sariisik

This study analyses the results of a pilot trial of a newly developed armed-chained stone-cutting machine. The machine was developed in Turkey and trialed at the Kaklik/Kocaba travertine quarries in the Denizli District. An armed-chained cutting machine is an alternative to the diamond wire cutting method more frequently used in the production of natural stone quarry blocks, and increases production efficiency and quality. Since there is no need to collapse the blocks using the armed-chained cutting production process, there is no risk of the block developing cracks. This results in a considerable increase in the efficiency of natural stone block production. The armed-chained cutting machine is easier both to assemble and run when compared to other block cutting methods. This process resulted in the production of a larger number of blocks at a lower cost within the same time frame, particularly in travertine quarries and in all other natural stone quarries. The block efficiency in travertine quarries was calculated as 65?80%using the armed-chained cutting machine, compared with 7?14% using the normal diamond wire cutting method.

Jan 1, 2010

By D. D. Ndenguma

This investigation compares the results from an experimental and numerical study of air flow in a scaled-down underground coal mine model. This was done in order to determine if numerical analysis can be relied upon when searching for ventilation solutions to control high concentration of coal dust and methane gas in underground coal mines. Steady state analyses were used to identify flow patterns and recirculation regions within the mining section while transient state analyses were used to determine the time taken to extract the initial air from the model. The agreement between the experimental and numerical results indicates that numerical modelling is useful in this regard. The study went further to devise a method of determining the optimum position of the jet fan that is responsible for mine-gas dilution at different stages of mining.

Jan 1, 2014

The paper provides a brief review of a multivariate uniform conditioning and a localized multivariate uniform conditioning (LMUC) technique, and presents a production reconciliation case study based on a porphyry copper-gold deposit in Peru. The reconciliation study compares the longterm LMUC mineral resources model (typical of new mining projects, which are invariably based on drilling data on a relatively large grid) to the corresponding production blast-hole grade control model, as well as the final plant production.

Jan 1, 2014