Search Documents

By K. N. Karparov

The classical limit equilibrium methods are suspected to be ineffective in predicting the potential for highwall failure in many instances in coal mines around the world. Slope engineers have for many years recognized a block thrust failure mechanism for slope failures, but little work had been done before 2000 to explain the actual mechanisms which must be responsible for the failure. The main reason for this is that limit equilibrium methods implicitly assume rigid blocks, and the resulting force equations must be satisfied everywhere simultaneously for them to have any meaning. This paper will show that the material involved in the slope failure is not rigid; indeed it undergoes considerable permanent deformation during failure. This observation allows the authors to treat the block boundaries independently, because they need not maintain a constant spatial relationship with one another, as is assumed in other methods. To enable analysis of this type the authors assume that the weight of the blocks is evenly distributed. This is reasonable, because the slope material is not strong enough to be self-supporting without some sort of constraint, or strong enough to be able to apply point loads to the surrounding material. The purpose of this paper is to extend the practical application of the analytical method developed from mechanism studies to provide an objective assessment of the risk of slope failure, and therefore guidelines for more stable slope designs. This work is based on studies carried out on two failures in an open pit coal mine in South Africa, and provides a methodology to assess the potential for failure more objectively than is possible with currently accepted methods, while at the same time remaining sufficiently simple to allow a ?back of the cigarette box? assessment by geotechnical engineers on site.

Jan 1, 2009

A Special General Meeting of the Institute was held in Kelvin House, Johannesburg on Wednesday, 29th September, 1971. The President, Prof. D. D. Howat opened the meeting at 9.55 a.m. The President read the notice of meeting which was as follows: "In order to bring industry into closer liaison with the work of your Institute and to place the Institute's finances on a sound basis your Council recommends that companies be admitted to membership of the Institute under clause 2.6 of the Constitution, that is, as Non-Corporate members. The designation for this class of member will be that of "Company Affiliate". 2 Membership: This clause to be amended as follows:- 2.6 "Non-Corporate members shall comprise the grades of:- Company Affiliate Honorary Fellow Graduate Associate Student" 2.6.1 This clause to be added:- "Companies involved in or associated with the mining or metallurgical industries are eligible to become company affiliates" 2.14 Add:- "A special certificate shall be issued to all company affiliates". After giving the background to the recommendation made by Council the President asked for a proposer and seconder for the resolution. Mr J. K. E. Douglas proposed and Mr D. G. Maxwell seconded the resolution. The meeting agreed that the constitution be amended as proposed. The meeting closed as 10.05 a.m.

By D. Tsweleng

In the Evraz Highveld production process, iron ore is prereduced in rotary kilns prior to charging into submerged arc furnaces (SAFs). Owing to the highly aggressive slags that are formed within the combustion zones of these kilns, chrome-oxide-containing lowcement castables have been used for some years in the kiln lining. Due to concerns around the potentially harmful effects should Cr(V1) be present in the spent linings, Highveld and its suppliers of kiln castables devoted time to developing alternative chrome-free lining materials. Such materials needed to be cost-effective and ensure good performance and improved kiln availability. This paper discusses all the parameters surrounding this development. Keywords Low-cement castable, chrome-oxide free, chrome (VI), titaniferous magnetite ore, rotary kiln, submerged arc furnace, open slag bath furnace, Evraz Highveld Steel & Vanadium Limited.

Aug 1, 2013

By T. Celik, B. Genc, C. Musingwini

"This paper discusses a new methodology for defining and measuring mine planning software utilization in the South African gold mining sector within an evolving data-set framework. An initial data-set showing the mine planning software providers, their corresponding software solutions, as well as the software capabilities and information on the number of licences was collected and compiled in 2012 in an online database for software utilized in the South African mining industry. Details of the database development and implementation were published in the Journal of the Southern African Institute of Mining and Metallurgyin 2013. In 2014 the data-set was updated with additional and new information. Using the 2012 and 2014 timestamps, a methodology for estimating the software utilization was developed. In this methodology, the three variables of commodity, functionality, and time factor were used to define and measure the software utilization in order to ultimately inform decision-making strategies for optimal software utilization. Using six different functionalities, namely Geological Data Management, Geological Modelling and Resource Estimation, Design and Layout, Scheduling, Financial Valuation, and Optimization, utilization in the gold sector was measured. This paper presents the methodology employed for measuring the mine planning software utilization. The methodology is useful for stakeholders reviewing existing software combinations or intending to purchase new software in the near future and who want to estimate the comparative attractiveness of a certain software package. These stakeholders include mining companies, consulting companies, educational institutions, and software providers. The work presented in this paper is part of a PhD research study in the School of Mining Engineering at the University of the Witwatersrand."

Jan 1, 2015

By S. M. Spottiswoode

Much as one hopes to predict whether damaging seismicity might occur somewhere in the next shift, this is not possible at present. Recently, an analysis of seismicity at two mines has shown that a small increase in seismicity occasionally occurs before both large and small events. This analysis is extended here to five mines, with the same results. Earthquake seismologists forecast hazard in terms of the average incidence of earthquakes over the last 50 years, adjusted on an hourly basis according to the possibility of aftershocks of events that have happened. The rate of seismicity in any area remains approximately constant when expressed as seismicity per area mined, or better still, per unit of elastic strain energy released. It is suggested that seismic hazard in mines be estimated using historical seismicity and forward modelling, adjusted according to the possibility of aftershocks. In summary, medium-term forecasting of seismicity is viable; short-term prediction of large events is not.

Jan 1, 2010

By J. M. Benson

Metal powder compaction offers unique advantages in the manufacture of net-shape components using techniques such as laser sintering, conventional press and sintering, metal injection moulding, direct rolling, direct forging, and hot isostatic pressing. If the output from the primary metal production process is in powder form, then considerable cost and energy savings can be realized by direct conversion to semi-finished or final shapes. This possibility exists for titanium and possibly also for Ta, Zr, Hf, and Nb metals. However, these attractive benefits are associated with some significant risks. The high surface-to-volume ratio of powder particles coupled with the reactive nature of these metals means that special care must be taken when handling them. Powder explosions are unfortunately still a regular occurrence internationally and these often result in serious injury and loss of life. Even seemingly 'safe' compounds such as sugar, flour, and grain can be extremely hazardous when handled or milled and dust clouds are produced. In addition, exposure to airborne particles can have adverse effects on the human body, especially when particles are inhaled on a regular basis. Furthermore, the medical consequences of these are not fully understood, especially in the case of nanoparticles. The impact is often not observed immediately and debilitating illnesses may emerge only years or decades later. As far as is known, there are no South African guidelines for handling of metal powders. This paper attempts to provide an awareness of the risks associated with metal powders (including those produced indirectly by other metalworking/finishing operations) as well as some guidelines for their safe handling, based on international best practices.

Jan 1, 2012

By I. A. Mwamba

Titanium sponge, which is almost pure titanium, is extremely ductile and not easily processed into titanium powder. One method of producing powder is the hydride-dehydride (HDH) process, where titanium sponge is hydrided to form brittle titanium hydride (TiH2). Titanium hydride is easily milled to produce powder and is then dehydrided to form Ti powder. In this work, titanium hydride powder obtained from titanium sponge was used as a starting material for blending and mechanical alloying with elemental powders. Firstly, titanium hydride powder was blended with aluminium elemental powder to produce a homogenized powder, which was then compacted and sintered to produce powder metallurgy compacts. Secondly, titanium hydride powder was mechanically alloyed with aluminium elemental powder and then compacted. The mechanically alloyed powder was characterized in terms of particle size distribution, morphology and microstructure. In both blending and mechanical alloying, the green compacts were characterized by assessing the green density, while the sintered compacts were characterized by their sintered density, microstructure, and hardness. The two processes have resulted in the formation of TiA13 intermetallic compound. It was established that by simple mixing and homogenizing, titanium hydride can be used as a starting material to produce powder metallurgy components in which porosity is a benefit rather than a problem, much akin to metallic foams. From the products obtained in the TiHz-Al system, it appears that titanium hydride can be used as a precursor in mechanical alloying. However, the possible formation of complex hydrides may introduce detrimental properties, and needs to be further investigated. For the production of non-porous components, it would be advisable to dehydrogenate the TiH2 powder before milling i.e. producing titanium powder by the hydride-dehydride (HDH) method. Keywords Mechanical alloying, titanium hydride, titanium aluminide and blending

Jan 1, 2011

By G. O. Oniyide, H. Yilmaz

The South African platinum mines in the Bushveld Complex (BC) have unique features that distinguish them from the gold mines. They have a higher horizontal stress closer to the surface, lower occurrence of seismic activity (caused mainly by pillar failure), and are sited in an area of high geothermal gradient. One of the future challenges of platinum mining is the increasing temperatures as the mining depth increases. High temperatures invariably bring about higher ventilation costs and require different approaches to human factors and ergonomics. Excavation stability would also be another area of concern due to increasing stresses. In this investigation, the effect of temperature on the physical and chemical properties of selected Bushveld rocks (chromitite, pyroxenite, norite, leuconorite, gabbronorite, mottled anorthosite, varitextured anorthosite, granite, and granofels) was studied by means of optical microscopy and scanning electron microscopy using energy-dispersive Xray spectrometry (SEM-EDX). The rock specimens were heated in a temperature-controlled oven a rate of 2°C /min to 50°C, 100°C, and 140°C and kept at temperature for five consecutive days. Samples were allowed to cool to ambient temperature (approximately 20°C) before image capturing. Micrographs of the specimens were taken before and after heat treatment. All the SEM samples were also subjected to heating and cooling on alternate days for ten days in order to observe the effect of repeated heating and cooling on the rocks. The results of the optical microscopy analyses showed minor physical changes in the rocks. The SEM images revealed that cracks initiating at lower temperatures extend with increasing temperature. The chemical analyses showed that the temperature range considered in this research is not high enough to induce changes in the chemical composition of rock samples.

Jan 1, 2016

By J. C. Ion, O. Isaksson, J. Stjernberg

Iron ore pellets are a preferred feedstock for ironmaking. One method used for pelletizing is the grate-kiln process, first established in 1960.During the past decade, the establishment of new grate-kiln plants has increased rapidly, especially in China, and new constructors of pellet plants have started to operate in the market. It is well known that the grate-kiln method yields a superior and more consistent pellet quality compared with the straight-grate process. However, certain issues exist with the grate-kiln plant, which are discussed here, together with proposed practical solutions.

Jan 1, 2015

By E. S. Peters, M. J. van Rensburg, M. Le Roux, Q. P. Campbell

"The demand for energy has continued to rise worldwide in line with population growth. The majority of South Africa’s electricity is supplied by coal-fired power stations. The amount of fine coal (-2 mm) generated at coal processing plants has increased, due mainly to mechanized mining methods. Fine coal retains more water, which lowers its heating value.Drying the coal is costly and it is difficult to achieve the required moisture content. Consequently, coal fines are often discarded. An estimated 8% of the total energy value of mined coal is lost1.Fluidized bed technology is often used to dry coal thermally, but this method is expensive and has an adverse environmental impact. The objective of this study was to investigate the removal of moisture from fine coal (<2 mm) in a fluidized bed operated with dry fluidizing air at moderate temperatures as the drying agent. The effects of different air temperatures and relative humidity levels were investigated in a controlled environment. The study further investigated the influence of coal particle size on moisture removal.The drying rate was found to increase with increasing temperature. The relative humidity of the drying air had a more pronounced effect on the drying rate, even at temperatures as low as 25°C.. It became more challenging to remove moisture as the particle size decreased. The gain in calorific value was greater than the energy required to dry the coal samples, showing that a fluidized bed using moderately warm dry air is an energy-efficient drying technology. The energy efficiency of the fluidized bed compared favourably with other thermal drying methods.Paper written on project work carried out in partial fulfilment of Degree in Chemical Engineering(NWU) - Pursuing Masters in Coal Beneficiation"

Jan 1, 2015

By J. H. Van Reenen, H. Thiele, C. Bergman

For some time spirals have been the process equipment chosen to recover metal in the size range 0.15 to 3mm from ferrochrome and silico/ferro manganese slags. Recoveries of metal obtained using spirals are usually about 70%. Spirals are also difficult to control. By combining a novel gate on the Apic pneumatic fines jig with the recently developed Apic classifier, metal recoveries of 76% and grades of over 90% have been obtained for FeCr and SiMn slags in the size range 0.15 to 3 mm. The paper compares classifier operating performance and costs with those spirals for FeCr and SiMn metal recovery from slags. The classifier technology can also be applied to chromite and iron ores and coal fines.

Jan 1, 2004

By S. Kwon

When an underground excavation is created near to an instrumented measuring location, deformation at the location increases. The characteristics of this deformation increase, as well as the duration of the influence caused by the adjacent excavation, is dependent on parameters such as opening geometry and measuring location. In this study, neural networks were applied to investigate the deformation increase and the influence of each parameter on the deformation change derived from extensometer measurements at the Waste Isolation Pilot Plant (WIPP) site in New Mexico, USA.

Jan 1, 1998

By C J. de Beer

The Kwaggashoek East pit is one of the four production areas of Thabazimbi Iron Ore Mine. The Kwaggashoek East Open pit mines through the abandoned sublevel caving operations of the Kwaggashoek East underground workings. A risk assessment indicated that the primary risk is the occurrence of surface subsidence. Based on local knowledge, a hypothesis, that most of the cavities were filled with broken rock as a result of roof collapse and bulking of failed material was formulated. To test the hypothesis a number of geophysical methods as well as probe drilling was utilized. The results of the resistivity, gravity and ground penetrating radar surveys were inconclusive in determining the position of voids. Either there were no voids present or the resolution of the surveys was not high enough to pick it up. It is accepted that only small voids remained, and that the supported roof hypothesis is valid. As a precautionary measure all the production blast holes within the caving area were over-drilled by forty percent. This would collapse the roof of any small voids or tunnels immediately below the block. This operation proved to be successful as two of the three underground levels have been mined out with no subsidence occurring in the pit floor.

Jan 1, 2006

By S. Subramanian, L. Mweene

A siliceous low-grade copper ore from Mpanda Mineral Field (MMF), located in south west Tanzania consisting of SiO2 (58.3%), Fe (10.4 %) and Cu (0.9 %) was initially subjected to selective dispersion-flocculation using sodium trisilicate (STS) as a dispersant and xanthan gum (XG) as a flocculant. Subsequently, the selectively flocculated fraction was floated using a collector combination of potassium ethyl and amyl xanthate (1:1) in the presence of poly-ethylene oxide (PEO) as a silica depressant, to get a copper concentrate. The mineralogical investigations confirmed that the MMF ore was mainly composed of quartz, chalcopyrite and pyrite. Adsorption studies indicated that the adsorption density of XG on MMF ore decreased with an increase in pH, while that of PEO was independent of pH. The adsorption isotherms of XG and PEO on MMF ore exhibited Langmuirian behaviour. The zeta potential studies of MMF ore indicated that the iso-electric point (IEP) was located at pH 2.6, presumably due to its high silica content. In the combined presence of XG and STS, the zeta potential of MMF ore became more negative, with an increase in the concentration of STS. However, in the presence of PEO, the zeta potential of MMF ore became less negative with an increase in the concentration of PEO beyond the IEP, without shifting the IEP. Selective dispersion-flocculation of MMF ore improved the flocculated chalcopyrite grade to 19.8 %, yielding a degree of flocculation and a maximum separation efficiency of 12.1 % and 85.7 % respectively, after three desliming stages in the presence of 30 ppm of STS and 30 ppm of XG. A copper concentrate of 29 % grade and 90 % recovery containing silica of 0.9 % grade and 1.7 % recovery was achieved by flotation of the selectively flocculated component, using PEO as a depressant for quartz. Keywords: Flotation kinetics, flotation machines, flotation bubbles, particle size

Jan 1, 2020

The additive property of dispersion variances was found experimentally by D.G. Krige using data from the gold deposits of the Witwatersrand. In this property, called ?Krige?s relationship?, the dispersion of a small unit, v, within the deposit is equal to the sum of the dispersion of v within a bigger unit, V, and the dispersion of these units, V, within the deposit, D. It is known that the variance of the grades decreases as the support increases, the so-called volume-variance relationship. To analyse volume-variance and Krige?s relationship, the methodology herein proposed combines blending piles and geostatistical simulation to simulate the in situ and the pile grade variability. Variability reduction in large piles is based on the volume-variance relationship, i.e. the larger the support, the smaller the variability (assuming perfect mix). Based on a pre-defined mining sequence to select the blocks that will form each pile for each simulated block model, the statistical fluctuation of the grades derived from real piles can be simulated. Using this methodology, one can evaluate within a certain time period the expected grade variability for various pile sizes, and also calculate the Krige?s relationship between the small blocks and the piles of different sizes. A real case study using a large Brazilian iron ore deposit illustrates the methodology and demonstrates the validity of the results.

Jan 1, 2014

By S. Budavari, F. M. C. C. Vieira

For several decades, the deep, gold-bearing reefs of the Witwatersrand basin have been mined predominantly according to layouts characterised by longwalls with strike pillars to provide regional support. During the past few years, a new generation of mining layouts has been introduced. These layouts are based on the concept of grid-type, scattered mining with dip pillars for regional support. As the extraction of the gold reefs extends to depths below 3500 m, the hazards associated with mining at these ultra-depths are expected to increase to unacceptable levels. Therefore, the question arises as to, which of the currently applied mining layouts is most acceptable for the economic and safe extraction of an ultra-deep orebody. The purpose of this paper is to describe a research investigation carried out to evaluate the degree of acceptability, from the rock engineering view point, of four currently used mining layouts for application at a depth-range of between 3500 and 5000 m. Pendant plusieurs décades, les filons d’or profonds du bassin du Witwatersrand ont été exploités d’une manière prédominante selon des dispositions caractérisées par des longues tailles avec des piliers directionnels pour donner un support local. Les dernières années ont vu la naissance d’une nouvelle génération de dispositions de mine. Ces dispositions sont basées sur le concept d’extraction type grille, éparpillée, avec des piliers au pendage pour le support local. Comme l’extraction des filons d’or va à des profondeurs en dessous de 3500m, il faut s’attendre à ce que les risques associés à l’exploitation à ces profondeurs extrêmes atteignent des niveaux inacceptables. Par conséquent, la question se pose de savoir laquelle des dispositions de mine couramment utilisées est la plus acceptable pour l’extraction rentable et sans danger d’un gisement ultra profond. Le but de l’étude présente est de décrire les recherches exécutées pour évaluer le degré d’acceptabilité, du point de vue d’ingénierie de roche, de quatre dispositions de mine couramment utilisées pour application à un rayon de profondeur entre 3500 et 5000m. Die tiefen, goldträchtigen Riffs des Witwatersrandbeckens wurden über einige Jahrzehnte hindurch vorwiegend nach jenen Layouts abgebaut, die von Langfrontstreben mit Schlagpfeilern charakterisiert waren, um regionale Unterstützung zu gewährleisten. Während der letzten Jahre wurde eine neue Generation von Grubenlayouts eingeführt. Diese Layouts basieren auf dem Konzept der Rasterfeld-Art, gestreuter Bergbau mit Neigungspfeilern für regionale Unterstützung. Es kann erwartet werden, daß auf Grund der Tatsache, daß sich die Extraktion der Goldriffs auf Tiefen unterhalb 3500 m verlagert, die Gefahren, die mit dem Bergbau an diesen Ultratiefen verbunden sind, sich auf ein nicht annehmbares Niveau erhöhen. Folglich erhebt sich die Frage, welche der gegenwärtig angewendete Abbaulayouts für die ökonomische und sichere Extraktion eines ultra-tiefen Erzkörpers am annehmbarsten ist. Zweck dieser Arbeit ist es, eine durchgeführte Untersuchung zu beschreiben, die vom Gesichtspunkt der Gesteinstechnik gesehen, vier gegenwärtig angewandte Abbaulayouts für den Einsatz in einem Tiefenbereich zwischen 3.500 und 5.000 m evaluiert.

Jan 1, 2003

By N. Anacleto, S. Ganguly

Reduction of Groote Eylandt (Australia) and Wessels (South Africa) manganese ores using CH4-H2-Ar gas mixture was investigated in a fixed bed laboratory reactor in the temperature range 1000?1200oC. The extent and kinetics of manganese ore reduction as a function of gas composition and temperature were determined by on-line off-gas analysis using mass-spectrometer and dew point sensor. Morphology of ores and its change in the course of reduction was examined by optical and scanning electron microscopy. Phases of raw materials and reduced samples were analysed by XRD and EPMA. Manganese oxides were reduced to carbide Mn7C3. High extent and rate of reduction by methane-containing gas in comparison with carbothermal reduction were attributed to high carbon activity in the reducing gas, which was in the range 15 - 50 (relative to graphite). The reduction rate of Wessels manganese ore increased with increasing temperature. Reduction rate and extent of Groote Eylandt manganese ore achieved maximum at 1050oC. The decrease in rate and extent of reduction of Groote Eylandt ore at higher temperatures, particularly at 1150-1200oC, was due to sintering and formation of semi-liquid silicate slag. The optimum conditions for the reduction of manganese ores were established as follows: a) temperature: 1150-1200oC for Wessels and 1050-1100oC for Groote Eylandt ores, b) methane concentration: 10-15 vol%, c) hydrogen concentration: above 30 vol%, (d) size: 1-3 mm. An addition of lime (10-15 wt% CaO) to the Groote Eylandt manganese ore increased melting temperature of slag and significantly increased the rate and extent of reduction at elevated temperatures.

Jan 1, 2004

By N. Demirel, O. Gölbasi

Draglines are massive machines extensively utilized in opencast mines for overburden stripping. The demanding working environment induces fractures, wear and tear, and fatigue failures in dragline components and eventuates in extended maintenance, lengthy downtimes, and loss of production. The bucket is the main source of external loads on the machinery, since interactions with ground materials take place in this region. This study aims to develop a generic finite element model of the stress on an operating bucket. This entails (i) three-dimensional modelling of a dragline bucket, (ii) analytical estimation of resistive forces in the bucket movement, (iii) three-dimensional simulation of the moving bucket using finite element analysis (FEA), and (iv) sensitivity analysis to examine the effect of formation characteristics on stress variation. Simulation results imply that the drag hitch and digging teeth are the elements of the bucket that are most prone to failure. In addition, sensitivity analysis indicates that internal friction angle of the formation is the dominant parameter leading fluctuations in stress values. Changes in stress level are least influenced by formation density.

Jan 1, 2015

By T. Scheldt, M. Lu, A. Myrvang

Abstract: In this paper both continuous and discontinuous modelling are utilised in order to analyze the stability of the Gjøvik Olympic Mountain Hall. The large span cavern (62 m) was built for the 1994 Winter Olympic Games at Lillehammer, and is a unique case study because of the large amount of available input data, through a comprehensive pre-investigation, stress and deformation monitoring program before, during and after the excavation. Phase2, a two-dimensional non-linear finite element program, and the Discontinuous Deformation Analysis (DDA) are used as representative tools for continuous and discontinuous modelling, respectively. The analysis results are compared and discussed taking the reliability of the models, time-consumption and costs into consideration. Some guidelines for the total modelling process, from field measurements to final results, are also presented. Zusammenfassung: In diesem Artikel werden sowohl kontinuierlich als auch diskontinuierlich Modellierung verwendet, um die Stabilität, der in den Berg gebauten Olympiahalle in Gjøvik zu analysieren. Die Olympiahalle wurde 1994 zu den Olympische Spielen in Lillehammer errichtet. Ihr Dach erstreckt sich über eine Breite von zweiundsechzig Meter. Für den Bau wurden umfangreiche Daten durch Voruntersuchungen, und Überwachung von Gebirgsspannungen und Deformationen bevor, während und nach Exkavation eingesammelt. Auf Grund dieser großen Datenmenge stellt die Olympiahalle ein herausragendes Beispiel für den Bau ähnlicher Projekte dar. Für die kontinuierlichen Modellierungen wurde „Phase2“, ein zwei-dimensionales, nicht lineares „endlich Element“ Rechnerprogramm angewandt. Die diskontinuierlichen Modellierungen erstellte man mit Hilfe von der „Diskontinuierliche Deformations Analyse“ (DDA). Die Analysenergebnisse sind mit Rücksicht auf die Zuverlässigkeit der Modelle, Zeitverbrauch und Kosten verglichen und diskutiert worden. Im Artikel werden Richtlinien für den Modellierungsprozess von Dateneinsammlung bis Schlussfolgerung gegeben. Résumé: Dans cet article la modélisation continue et discontinue sont utilisés pour analyser la stabilité de Gjøvik Olympic Mountain Hall. Cette caverne de grande portée (62 m) a été construite pour les Jeux Olympiques d’Hiver de 1994 à Lillehammer, et est une étude de cas unique grâce à la grande quantité de données disponibles, de par un programme de pré-investigation compréhensive, monitorage des contraintes et déformations avant, pendant et après l&apos;excavation. Phase2, un code d’éléments finis non linéaire à deux dimensions, et l’Analyse en Déformations Discontinues (DDA) sont utilisés comme outils représentatifs de la modélisation continue et discontinue, respectivement. Les résultats d&apos;analyses sont comparés et sont discutés, prenant en compte la fiabilité des modèles, la consommation en temps de calcul et les coûts. Quelques indications pour le procédé total de modélisation, des mesures sur place aux résultats finaux, sont aussi présentées.

Jan 1, 2003

By S. K. Murphy, K. B. Le Bron, A. K. Ward, S. Hayes, T. Rangasamy

A process for evaluating different options for extraction of mining blocks is presented. The process is described and an example of the application of the process to a case study is presented. Un procédé pour évaluer différentes options pour l’extraction de blocs d’exploitation est présenté. Le procédé est décrit et un exemple de l’application du procédé à un cas particulier est présenté. Ein Prozeß für das Auswerten der unterschiedlichen Optionen für die Extraktion von Abbaublöcken wird dargestellt. Der Prozeß wird beschrieben und ein Beispiel der Anwendung des Prozesses zu einer Fallstudie wird dargestellt.

Jan 1, 2003