Search Documents

By N. A. Smith, R. J. Fowell, J. L. Hislam

Abstract: Data are presented from two sites in southeast England, where problems were encountered in tunnelling through ground containing flint. In response to the difficulties, substantial laboratory testing programmes were initiated to determine the strength of the flints.It is shown that the strength varies very considerably, even within a single flint particle and that the practice of estimating unconfined compressive strength by a single multiplier applied to the point load strength index (Is(50)) may give misleading results. The preparation of UCS specimens for testing was found to be very difficult and it is recommended that tunnel machine capacity is assessed relative to Is(50). Résumé: Des données sont presentées sur deux sites dans le sud-ouest de l’Angleterre,où le perçage d’un tunnel dans un sol contenant du silex a posé des problémes. En consequences de ces difficultés, des programmes substatiels de recherché en laboratoire ont été initiés afin de déterminer la resistance des silex. Il est demontré que la resistance varie considérablement, même au sein d’une particule de silex, et que la pratique de estimation de la résistance en compression non confinée, (UCS) par le biais d’un simple coefficient appliqué au ‘point load strength index (Is50)’ pourrait donner des resultants trompeurs. La préparation de specimens UCS destinés aux tests s’est avérée trés difficile et il est recommandé que la capacité de la machine de perçage de tunnels soit calculée relativement au Is50. Zusammenfassung: Daten von zwei Standorten in Südosten von England, wo Probleme beim Tunnelbau durch feuersteinhaltigen Grund antraffen, sind angegeben. Wegen diesen Schwierigkeiten wurden Laboratoriumsforschungsprogramme eingeleitet, um die Festigkeit von Feuersteinen zu bestimmen. Es wurde gefunden, dass die Festigkeit sehr unterschiedlich war, selbst bei einzelnen Feuersteinstücken, und dass die Praxis, die unbegrenzte Kompressionsfestigkeit (uKf) auf Grund eines einzigen Multiplikationsfaktors vom Punktladefestigkeitsindex (Is50) abzuschätzen, zu irreführenden Resultaten führt. Die Vorbereitung der uKf Prüfstücke war sehr schwierig und es wird vorgeschlagen, dass die Kapazität der Tunnelbaumaschine in Abhang der Is50 bestimmt wird.

Jan 1, 2003

By M. A. Kujoana

Following on the design of good mining layouts and regional support systems, and the implementation of sound strata control practices, stope support is the ultimate strategy to combat the hazards of rockfalls and rockbursts. The primary function of stope support in intermediate and deep level mines is to stabilize the rock mass immediately surrounding stoping excavations, that is, the zone of fractured rock which behaves in elastically around stopes. Support design is a process resulting in a support system which is both practical and meets or exceeds by a factor of safety the requirements for a particular geotechnical environment. The aim of this project was to design a support system, which accommodates the factors of rockfalls and rockbursts. The pack support unit must be easily handled, less costly and can be used in stopes without any significant convergence. The project tested the structural stability of packs to their expected deformation, in order to design a height to width ratio for stopes where little convergence is expected.

Jan 1, 2009

By S. Y. Chen

A new process comprising metallizing reduction, magnetic separation, and electroheat melting separation is proposed with the aim of achieving high recoveries of iron, vanadium, and titanium from vanadium titanomagnetite. The effects of magnetic intensity, reduction temperature, reduction time, carbon ratio, and coal particle size on the efficiency of reductionmagnetic separation were investigated, the reaction mechanisms elucidated by SEM and EDS analysis, and the optimal process parameters established. Recoveries of up to 80.08% for titanium, 95.07% for iron, and 71.60% for vanadium were achieved. The reduction sequence is shown to be: Fe2O3 ? Fe3O4 ? FeO ? Fe; Fe2TiO5 ? Fe2TiO4 + TiO2 ? Fe + FeTiO3 ? Fe + FeTi2O5 ? Fe + TiO2.

Jan 1, 2014

By D. Schreuder

Conditions in the South African market relating to atmospheric emission control has changed dramatically over the last 10 years. Companies have become more responsible, environmentally aware, and have to comply to more stringent environmental limits set by legislation. This paper describes briefly the current best available atmospheric pollution abatement technologies relating to particulates, acid gases, NOx, acid mists, aerosols, mercury, dioxins and furans. Mention is also made as to the best practices for product work-up and waste product disposal.

Jan 1, 2006

Abstract A new approach is introduced for study of the behaviour of geotechnical strength parameter prior to slope analysis to ascertain whether strength parameters of slope materials are homogenous or heterogeneous at different mine depths. The strength parameters used for the study are uniaxial compressive strength, tensile strength and shear strength. The analysis is based on statistical analysis of variance technique for one-way classification. The application of the technique is given through a case study in an openpit mine. Auszug Eine neue Annäherung wird für Studie des Verhaltens des geotechnischen Stärke Parameters vor Steigunganalyse eingeführt, um zu ermitteln, ob Stärke Parameter der Steigungmaterialien homogenous oder an den unterschiedlichen Grube Tiefen heterogen sind. Die Stärke Parameter, die für die Studie verwendet werden, sind einachsige zusammenpressende Stärke, Dehnfestigkeit und Scherstärke. Die Analyse basiert auf statistischem varianzanalytische Technik für Einwegklassifikation. Die Anwendung der Technik wird durch eine Fallstudie in einer openpit Grube gegeben. Abstrait Une nouvelle approche est présentée pour l'étude du comportement du paramètre géotechnique de force avant l'analyse de pente pour établir si les paramètres de force des matériaux de pente sont homogenous ou hétérogènes à différentes profondeurs de mine. Les paramètres de force utilisés pour l'étude sont résistance à la pression uniaxiale, résistance à la traction et résistance au cisaillement. L'analyse est basée sur statistique la technique de l'analyse de variance pour la classification à sens unique. L'application de la technique est donnée par une étude de cas dans une mine à ciel ouvert.

Jan 1, 2003

By B. Samanta

LHD (load haul dumper) is now used as a loading machine for intermediate mechanization in underground coal mining. For survival in the intense competition in the global business environment in recent years it is essential that LHD machine should be reliable and maintained effectively and efficiently. This paper seeks to study the reliability, availability and maintainability (RAM)of an LHD machine with failure and repair data by Markov modelling. The constraints and reasons for machine unavailability are outlined. The reliability and maintainability of an LHD and its subsystems are evaluated. Possible modification or design alternatives are highlighted. Reliability and maintainability of an LHD system are disappointing. There is room to take decisions on optimal maintenance planning and machine improvement from this analysis. Keywords: reliability, availability, maintainability, Markov model, LHD

Jan 1, 2004

By A. Beitz, P. Smartt, G. Einicke, G. Rowan, P. Glynn

Coal is Australia’s highest export earner and Australia is the world’s largest exporter of coal. With coal now being extracted from deeper reserves under increased risk profile, and in the interest of aiding the stability of coal supplies, Japan is funding a number of safety projects in Australia and China. The CSIRO, Australia’s premiere research organisation with the country’s largest exploration and mining research group, are currently undertaking a jointly funded Japan-Australia safety project at Anglo Coal’s new Grasstree Colliery in central Queensland. The project, entitled Mine Communication and Information for Real-time Risk Analysis, will deliver step-change capabilities in data integration, decision support, gas monitoring, geo-technical monitoring, emergency response and personnel safety to the Grasstree Colliery. Some key activities include: developing and installing underground coal mine Ethernet LAN components, real-time monitoring of gas and geo-technical sensors, MODBUS serial to TCP/IP converters, e-reporting of underground conditions, emergency guidance systems and underground trials of Internet Protocol telephone and video. The project seeks to integrate (in real time) key data sets from the comprehensive and diversified range of propriety system currently in use at mines (ventilation, strata, operations e.g. haulage, pumps, conveyors etc) into a single integrated risk management interface. This interface will filter the data through a rules-based inference engine that will cross reference the various data streams, compare with past events and outcomes associated with the similar historical data and present this “intelligence” to

Jan 1, 2003

By Y. Jin

Magnesia ramming materials have been widely used in China instead of magnesia bricks as furnace lining materials of ferroalloy refining furnace. The paper introduces the development of the ramming material, recounts its chemical composition, physical property and application characteristics. Because of its high MgO contents and fine sintering property, the ramming furnace bottom has the properties of good refractory, monolithic construction and thermal shock resistance. The changes in mineral composition and furnace tearout characterization show the reasons for the bottom?s long service life. The obvious benefits are widely achieved, the annual saving cost in refractory is about 2 millions US dollars.

Jan 1, 2004

By S. Ganguly

Slag samples taken from adjacent to the furnace wall of a submerged arc ferromanganese smelting furnace have been found to contain high concentrations of K2O. To characterize the phase equilibria relevant to these slags experimental studies have been carried out to determine pseudo-ternary sections of the form ?MnO?-CaO-(SiO2+Al2O3) with a fixed Al2O3/SiO2 weight ratio of 0.65 and 6.0 wt% K2O for temperatures in the range 1523-1673 K. In the pseudo-ternary section investigated the primary phase fields are found to be mullite, 3Al2O3?2SiO2; corundum, Al2O3; spinel, MnO?Al2O3; manganosite solid solution, (Mn,Ca)O; dicalcium silicate,2CaO?SiO2; gehlenite 2CaO?Al2O3?SiO2; anorthite CaO?Al2O3?2SiO2; kalsilite KAlSiO4 and leuciteKAlSi2O6. It was found that the presence of K2O in the slag decreases liquidus temperature in the anorthite and gehlenite primary phase fields. The manganosite primary phase field is expanded in the direction of increased (Al2O3+SiO2) and the liquidus temperatures in the manganosite primary phase field are increased significantly with the presence of K2O in the slag.

Jan 1, 2007

By Christian Roche

Our study is focused on the sub-assembly con-tact shoes, pressure rings and pressure bellows. We were keen to mainly study [ ] 1.The contact shoe design 2.The most efficient pressure to ensure an optimal electrical contact between the contact pad itself and the casing 3. The contact shoe cooling circuit in view to provide to the shoe the best mechanical and electrical characteristics in order to bring to the users of COFOR® components a new standard in process setting technical solutions. A finite elements simulation, combined with a thermal and structural studies were used. Our presentation which follows is dedicated exclusively on the influence of the contact shoe cooling system on the process through a thermal and structural analysis. [ ]

Jan 1, 2007

By R. P. Goel, P. N. Chaudhary, R. K. Minj

The bulk of high carbon ferromanganese produced in India continue to have more than 0.35% phosphorus since they are produced by carbothermic reduction process. The low phosphorus manganese ores are depleting fast and ferromanganese manufacturers will have no option but to use medium and low grade ores having high phosphorus content resulting in high phosphorus in the product. A systematic study was taken up at NML to solve this problem. Initially, a thermodynamic analysis was carried out for which Ba-P-O ternary predominance diagrams were constructed at several temperatures to predict the most suitable conditions for selective removal of phosphorus from high carbon ferromanganese. These conditions required a usage of a flux having a high level of basicity, moderate oxygen potential as well as low melting temperature. The experimental results showed that it was possible to remove phosphorus from high carbon liquid ferromanganese from 0.56%to 0.18% using BaCO3 based fluxes at the rate of 16-wt% of the ferromanganese charged. However, the Mn loss varied in the range of 2-5%. The objective of the subsequent study carried out at the laboratory scale was to optimize the flux consumption as well as minimize the Mn loss with effective dephosphorization by using BaO based calcined pellets instead of BaCO3 based powders. It was felt that the handling of pellets under plant conditions would be easier and also eliminate the loss of flux as a dust, which occurs when powder is added. These pellets were forced towards the bottom of the melt for better efficiency. For this purpose, a plunging system was designed and fabricated in-house that helped in reducing the flux consumption to less than 5% and also improved the kinetics of the process. The desired results were achieved within 10 minutes of the addition of the flux. The know-how is ready for transfer to interested parties and authors are willing to conduct large scale trials with them.

Jan 1, 2007

By Rajendra Singh

Underground depillaring of contiguous coal seams/sections is a difficult problem, which becomes even more complex if the interburden/parting between them is thin. Conventionally, the depillaring with caving of contiguous seams/sections is done in descending order. However, if the parting is thin, the influence of the top sections/seams working over the standing pillars of bottom the sections/seams becomes extremely important for the safety and optimal exploitation of coal. Field investigations were carried out at Nowrozabad East mine where superimposed pillars of the Johilla top section were depillared above the developed pillars of the Johilla bottom section with a 3 m thick parting between the two sections. The competency of the 3 m thick parting (which consists of alternate layers of shale, sandstone and shaly sandstone) was improved by reinforcement (underpinning). The strata control investigations did not show any considerable instability problem of the 3 m thick reinforced parting and pillars of the bottom section due to top section depillaring. On the basis of this field investigation and a laboratory study on simulated models, simultaneous extraction of both the sections, along with reinforcement of the parting, was suggested for the geomining conditions of the Johilla top and bottom sections. Adopting the suggested simultaneous depillaring process, two sub panels of Johilla top and bottom sections have successfully been extracted without any strata control problem. This paper presents this case study along with the results of the strata monitoring conducted to evaluate performance of the underground structures during the field trial.

Jan 1, 2004

The current methodology to design stope support systems in South African gold and platinum mines is based upon the tributary area concept. The discontinuous nature of the hangingwall rock is not adequately addressed, and mechanisms leading to rock mass failures between adjacent support units are poorly understood. The work reported here aims to formulate a basis for quantifying support mechanisms and gain insights into the influence of rock discontinuities on stable hangingwall spans. Numerical models are used to qualitatively investigate the stress transfer from the support units to the discontinuous hangingwall. Stable hangingwall spans are quantified by considering two failure mechanisms, namely (i) beam buckling, and (ii) shear failure due to slip at the abutments. The output of the proposed design methodology is appropriate site specific support spacing, based on discontinuity spacing and orientation. The method is particularly suited to mines at intermediate and great depth, where typically the hangingwall is highly discontinuous due to face parallel mining induced fractures. Results of parametric studies show that with increasing in situ compressive hangingwall stress, beam thickness and friction angle, hangingwall stability is increased, leading to wider stable hangingwall spans between adjacent support units.

Jan 1, 2000

By U. Weber

The effect of grinding media performance on milling and operational behaviour was demonstrated under different selected conditions of calcium carbonate slurry milling. A variety of grinding media materials and bead sizes, along with two different stirrer tip speeds, were used in the grinding process to generate a particle size reduction of the calcium carbonate (CaCO3). To determine the optimum milling parameters the collected test data were used to calculate and evaluate specific energy as well as stress intensity under different milling conditions. Keywords: Grinding, mill media, high energy mills, industrial minerals, precious metals.

Jan 1, 2010

By G. R. Lane, A. Vermeulen, S. van de Venter, S. Bhoowanpursadh

Over the past two years Anglo Platinum made use of the specialist skills of Cyest Corporation to develop a Mine Optimization Tool (MOT) to enhance the current suite of in house mine planning tools and processes. The application was built in a multidimensional modelling environment developed by Cyest called CarbonL. This has allowed complex modelling that is transparent to the business users and therefore is not prone to the ?black box? approach that generally exists with these types of complex tools. The purpose of the MOT is to have an integrated software tool that can schedule production activities by half level for a shaft complex, while at the same time integrating the economics concomitant with that schedule. The tool allows the user to configure all activities relevant to the selected mining method, define the mine design parameters and geological parameters, define scheduling rules and then schedule all activities. This allows the user to test various production strategies and schedules very quickly and easily in terms of shaft value, costs and revenue profiles, labour complement and production ramp up so as to determine the option that best fits the overall strategy. This allows assessments of multiple scenarios in a relatively short period of time, after which only the best option is taken forward for graphic design and scheduling. This paper discusses briefly the rationale behind the Mine Optimisation Tool and the underlying workings of the modules that comprise the tool. It also covers the life cycle of this tool from the original prototype through to the final Mine Optimisation Tool software and discusses the positioning of the final tool.

Jan 1, 2007

By H. E. Bartlett

In the operation of some flotation plants treating platinum ores it was found that there were imbalances between the inputs and outputs. The inputs and outputs were sampled as slurries and it was determined that the imbalances arose from biases in the sampling, despite the samplers having been designed according to well-established rules. The launders feeding the sample cutters, and the sample cutters themselves were redesigned using finite element analysis to model the flows. A new set of design rules were formulated. The application of a Components of Variance Analysis, to determine the variance of primary and secondary sampling and of analysis in the lab for a concentrate is presented to illustrate the need for frequent sampling of process streams.

Jan 1, 2002

By G. van Aswegen

Seismic monitoring became commonplace in the deep South African gold mines in the early 1990’s. The discipline has, to a large extent, developed beyond the ‘research’ stage, and a ‘Guide to Seismic Monitoring in Mines’ has been accepted by the Department of Minerals and Energy1. Although ongoing research is a requirement for the achievement of all the objectives of seismic monitoring in mines, sufficient knowledge exists to apply seismic monitoring for routine seismic hazard assessment as an aid to risk management. The design and management of seismic monitoring systems can be tested against requirements spelled out in the ‘Guide’. Assuming the seismic monitoring system performs as per requirement, the best practice for routine seismic hazard assessment in mines includes • Long term seismic hazard assessment: through back analysis of seismic data and correlation with numerical modelling output, reasonable tests for planned mine designs are possible. • Medium term seismic hazard assessment: o Spatial analysis through contouring of seismic strain related parameters, with superimposed contours or event plots of stress related parameters allow the delineation of potential instabilities in space. o Quantitative and statistical analyses of seismicity in smaller spatial units (usually encompassing production sites) allow the comparative seismic hazard rating of different areas/sites so that rock engineering input and risk management can be optimised • Short term seismic hazard assessment relies mainly on time history analyses of particular seismicity parameters. The temporal patterns are controlled by a combination of temporal and parameter filters, the optimisation of which determines the success rate.

Jan 1, 2003

The effect of composition on electrical conductivity (resistivity), viscosity and liquidus temperature of the slags encountered in electric smelting of PGM containing suphide concentrates is reviewed, along with the relationsip between slag composition, slag-matte separation and metal losses to slag. Optimization of slag composition at furnace temperature is attempted on the basis of opposite and parabolic trends of the viscosity-conductivity relationships of the slags. The importance of surface tension of slags is emphasized using available and estimated information which are grouped into a useful correlation. These values are coupled with or incorporated into slag viscosity plots to illustrate the correlation between the two factors, which influence slag-matte separation as well as refractory attack. The electrode in the slag-resistance furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power. The obvious parameters are the size and positioning in the slag bath, which are defined by slag resistively, furnace resistance, cell constant and power input. The flow of heat generated by the electrode current determines the energy distribution and furnace dimensions creating viscosity profiles, which in turn affect flow conditions. Thus the flow of slag and matte are discussed in conjunction with the furnace geometry, stirring action of the electrodes, buoyancy and electromagnetic effects. The action of the electric furnace as a settler is discussed. The rectangular furnace is considered as a channel reactor in this analysis, and the action of the electrodes is described to indicate a balanced settling rate in the area of electrode action. Discussion of the design and production capacity of the electric furnace, with reference too perating current, power input, furnace dimensions and electrode size, are based on considerations derived mainly from slag properties such as its resistively, viscosity and liquidus temperature.

Jan 1, 2004

By H. Kotzé

Titania slag is used as feedstock in the production of titanium dioxide pigment. It (titania slag) is the product of ilmenite smelting,a process whereby ilmenite is reduced at high temperature utilizing anthracite as a reducing agent. Although various slag tapping configurations are employed throughout the ilmenite smelting industry, the method of tapping the slag from the furnace into bell shaped cast steel pots, was the subject of investigation in this study. The paper describes the formulation of a cooling model used to calculate and subsequently predict the temperature profile of a slagblock during its cooling within the various cooling environments of pot cooling, air cooling and water cooling. The model was calibrated against actual internal slag temperature measurements and verified with information obtained from both pilot and industrial scale blocks. The paper concludes with solidification results and their practical implication.

Jan 1, 2010

The re-use of waste water from coal preparation plant tailings is always desirable, but is generally problematic in terms of solid-liquid separation. Dewatering and disposal of coal slurry at a high percentage of moisture poses a major technological and environmental challenge to mining and mineral processing industries world-wide. Characterization and flocculation of these coal tailings reveals that the separation of fine coal tailings depends on factors such as size distribution, slurry viscosity, zeta potential, pulp density, circuit design, plant operating parameters, and the behaviour of solid particles in an aqueous medium. The present study was carried out on -600 mm coal tailings collected from a coking coal preparation plant of Jharia Coalfield, India, using anionic flocculent. Characterization studies revealed that the zeta potential was highest (-44 mV) at a pH of 9.0, the size range of the particles was 1.1?700 m, and the average ash content was 62.57%. Flocculation studies were performed at different solid concentrations, pH values, and polymer dosages. The results indicated an efficient settling rate of 178.15 mm/min at 8% solid (w/w) at a flocculent dosage of 32.50 g/t solid. The turbidity of the clear liquid obtained was 7.42 NTU.

Jan 1, 2014