Search Documents

By P. T. L. Koh, M. P. Schwarz

A series of parametric studies were carried out for a flotation cell using computational fluid dynamic (CFD) modelling to determine the local response of hydrodynamic performance measures to change in operating conditions. As an example, an Outotec cell was used to carry out the response analysis. The hydrodynamics of the flotation cell has been previously investigated by laboratory measurements presented by Schwarz et al (2019), and a CFD model of the cell was developed and validated using these measurement data (Schwarz et al., 2019). In this work, parametric studies have been performed by modelling the flotation cell at different stirring speeds and gas flowrates, varying above and below standard conditions. Predictions of void fraction, bubble size, bubble surface area flux and particle–bubble collision rate are presented showing the effects of increasing and decreasing stirring speed and gas flowrate around the base case. Generally, the total gas holdup in the flotation cell was found to increase with increasing gas flowrate. The bubble diameter was found to decrease with increasing stirring speed and increase with increasing gas flowrate. The collision rate increased with both stirring speed and gas flowrate. The parametric results show that there is a correlation between the bubble surface area flux Sb which is affected by stirring speed and gas flowrate, and the particle–bubble collision rate. With the collision rate as an indication of flotation collection, it is also possible to show that cell performance can improve more by increasing stirring speed than by increasing gas flowrate in a situation where everything else remains constant. The CFD results can form the basis for a Response Surface Method (RSM) analysis which can then be used for automated optimization of cell performance. Keywords: Flotation kinetics, computational fluid dynamics, bubble surface area flux, particle-bubble collision rate

Jan 1, 2020

By John Taylor

?Introduction to Black Mountain ?Historical metal accounting practice ?Metal accounting audit ?Feed measurement ?Sample precision ?Concentrate measurment ?Current metal accounting practice ?Further refinements to the metal accounting practice

Jan 1, 2005

By L. Wade

Laboratory testing of the self-heating propensity of coal, using crossing-point temperature and differential thermal analysis techniques, involves the frequent recording of several temperatures. The volume of data and the desire for high accuracy of measurements motivates an automated recording system. The data which are recorded must be adjusted for calibration factors and the results presented in both graphical and tabular form. The paper describes hardware and software features of a computerised system which is being used to establish the relative propensity to self-heating of a wide variety of coals.

Jan 1, 1987

By A. C. Wingrove

The paper outlines the selection of a dewatered tailings backfill system for the Johannesburg Consolidated Investment Gold Division, and covers the following aspects: (i) 16 Shaft pilot testwork; (ii) engineering design problems relating to the Cooke 3 Shaft backfill operation; (iii) in-line mixing - applications with respect to the Randfontein Estates Gold Mine and Western Areas Gold Mine backfill operations; and (iv) pipeline friction losses.

Jan 1, 1988

By S. Banisi, A. Ghasemi, E. Nematollahi

Discrete element method (DEM) has been used as a popular simulation method to verify designs by visualising how material will flow through complex equipment geometries. Although DEM simulation is a powerful design tool, finding a DEM model which includes real material properties (e.g., shape, cohesion and friction coefficients) is not computationally feasible. In order to obtain more realistic results, particle energy loss due to rolling friction has been highlighted by many researchers. To implement a reverse torque to account for rolling friction, various models have been proposed. On account of the complexity of the problem, there is no unique model for all applications (i.e. dynamic and pseudo-static regimes). In this paper, an in-house developed DEM software (KMPCDEM ©) was used to assess the robustness of three commonly used models by comparing the repose angle of iron ore pellets obtained through the draw down test in a laboratory setup and then the elastic–plastic spring dashpot model was modified based on considering the individual parameters instead of relative parameters of two contact entities. Results showed that the modified model could produce higher repose angle. The modified model was used to calibrate DEM simulation of repose angle of iron ore pellets in a laboratory setup of the draw down test. Comparison of the calibrated DEM simulation and laboratory results showed 2° differences between the predicted and measured angle of repose. This difference was attributed to considering the particle shape effects by assuming a spherical shape for particles. Keywords: DEM, rolling friction,particle shape, repose angle

Jan 1, 2020

Orebody modelling and reserve estimation are now subject to sophisticated procedures, but folded stratiform and stratabound deposits present particular problems in transforming coordinates of samples and blocks into their correct relative positions prior to deformation. In this paper an approach is taken whereby a geologically interpreted reference plane is used as a control. The study area is the Rio Tinto Minera copper mine near Santiago de Compostela, Spain. The transformation procedure on the 'unfolded' state is described, its limitations assessed and advantages considered.

Jan 1, 1987

By D. Royston

Mill liners provide the wear-resistant surface within grinding mills, they also impart motion to the mill charge, ie the grinding process, by providing the key between the charge and mill shell, and, at the discharge end, they remove the ground contents of the mill. As semi-autogenous grinding (SAG) mills have grown in size the process aspects of liner design and their impact on mill performance have become particularly important. While feedback from practical experience is critical to good mill liner design, increasingly sophisticated computer-based tools are being developed to assist in mill liner design.

Jan 1, 2007

By T. De Lange

Extensions to the beneficiation plant at the Grootegeluk Coal Mine are currently being planned in order to provide power station coal for Escom's Matimba Power Station, presently under construction. A simulation model was developed on the Olivetti M-24 microcomputer to facilitate the development of the envisaged flowsheet. The computer program simulates the heavy-medium separation and screening unit operations. The model is based on the construction of the Tromp partition curve described by an arctangent function, allowing ideal and non-ideal separations. The paper discusses the determination of the parameters required by the arctangent curve from standard process parameters such as Epm, Wolf cut-point, Tromp cutpoint and screening efficiency. The accuracy and shortcomings of the model are discussed, while an overview of the application of the model to evaluate borehole and bulk sample analyses is also given. It is concluded that the model is an invaluable aid to general flowsheet development.

Jan 1, 1987

By K. Lomberg

In this paper the process of sampling and assaying as it relates in particular to the platinum group elements (PGEs) is presented. A discussion of the geology of PGE deposits is included to provide an understanding of the mineralization that is considered necessary prior to sampling, as this has a direct bearing on the mineral resource estimate and also the selection of an appropriate mining cut. The discussion includes the selection of the sampling technique (drilling or face sampling), the size of the sample relating to the requirements of the laboratory, the potential mining cut, as well as a reference to sampling theory. The selection of an assay technique that is appropriate and will yield the optimal result based on sample turnaround, precision, accuracy, and cost is then considered. Examples are drawn from work undertaken on the Bushveld Complex (Merensky Reef, UG2 Chromitite Layer, Platreef) and Great Dyke (Main Sulphide Zone). A discussion of the appropriate QA/QC programme includes the chain of custody, CRM selection and the QA/QC process. Keywords sampling, assaying, QA/QC, platinum group elements.

Jan 1, 2014

By B. B. Tati

The project report is based on vacation work done by the writer at the Khutala Colliery during December/January 2009?2010. The purpose of this report is to explain and describe the design process in a multi-seam mine design for coal extraction at the Khutala Colliery. The multi-seam design will focus on the No. 2 and No. 4 seams as these are the seams that are currently being mined by underground methods at Khutala Colliery. The seam thicknesses and the parting thickness between the seams provide suitable conditions for designing a multi-seam mine design. An investigation into the pillar design aspects is carried out followed by a numerical modelling analysis of various scenarios. This analysis validates the first principles approach provided by multi-seam design guidelines. The design results from the analysis of the selected pillar design indicate sufficient parting for primitive conditions between seams, thus illuminating the need for superimposing in-panel pillars. This multi-seam mine design confirms the potential for the extraction of coal in a new panel. The design indicates that significant amounts of power station coal are present and suitable for extraction by room and pillar mining methods. The panel block indicates 401 625 tonnes of ROM coal. This block has a life of panel that will be mined just over a 4-month period. This 4-month period is assumed to mined at a production rate of 48 000 tonnes per month. The total capital cost required for the new panel is R48 281 127.05. Keywords Multi-seam mining, panel design, ventilation flow, superimposition.

Jan 1, 2011

For practical reasons all basic input data for the gold mines of the Anglovaal Group conform to a regular grid of averages of sample values within 25-ft squares in the plane of the ore body; individual sample values with their metric co-ordinates are input and converted by a computer program to the basic 25-ft square averages. At the Prieska copper mine the bore- hole data are forced on to a regular grid of 15-m squares corresponding to the coordinates of the grid points nearest to the actual borehole intersections. As for the gold mines the Prieska ore body, although some 3 to 30 m thick, is also dealt with on a two-dimensional basis (Krige, 1973). On the gold mines the data subjected to geostatistical analysis cover: gold values (in cm g/t), uranium values (cm kg/t), and channel widths (cm). The gold and uranium values are normalised on the basis of log (value plus constant) and all the geostatistical analyses are performed on these transformed values. The channel widths usually conform reasonably well to the normal distribution and are, therefore, not transformed. At Prieska the metal grades analysed cover the two main products, copper and zinc, as well as the impurities lead and bismuth; in addition the specific gravity values and the hanging- and foot-wall deviations from a projection plane are also handled. These were all previously used on an untransformed basis but because of problems associated with the proportional effect the lognormal-de Wijsian model is now used for some of the grade variables. The key computer pro- grams can be summarised briefly as follows:

Jan 1, 1981

By C. Botha

The South African democratically-elected government instituted policies and legislation that are intended to bring about change and transformation in the country and have drastically affected different industries, among others, the mining industry. The Mineral and Petroleum Resources Development Act 28 of 2002 (MPRDA) and the Broad-based Socio-economic Empowerment Charter (Mining Charter) were introduced in order to redress previous inequalities and to promote women's employment in the mining industry. This research evaluates the practical implementation of the MPRDA and the Mining Charter with specific reference to women in underground mining. A quantitative research paradigm was used. Data were collected through a process of a face-to-face interview surveys utilizing a structured questionnaire. The research setting was limited to the platinum-mining industry in the area of Rustenburg in the North West Province. The study population consisted of 195 available women working undergound at the mine. It is clear from the findings that mining companies are facing major challenges in their attempt to incorporate women in underground mining activities. Company policies regarding these issues must be firmly in place; however, the challenge lies in the translation of these policies into practice. In this regard, managers will have to play a leading role in the successful phasing in of women into the underground mining arena.

Jan 1, 2012

By R. H. Matjie, J. R. Bunt, C. A. Strydom

"A number of conventional and advanced analytical techniques (proximate and ultimate analysis, low-temperature oxygen-plasma ashing, X-ray diffraction, X-ray fluorescence spectrometry, coal petrography, and lightelement electron microprobe analysis) have been integrated and crosschecked to provide detailed characterization of coals from the Highveld coalfield in South Africa, as a basis for better understanding of the mineralogical and chemical properties of the individual coal sources that are blended as feedstocks for combustion and carbon conversion processes. The techniques included methods to quantify the abundance and composition of the mineral matter (minerals and non-mineral inorganic elements), and also the abundance and chemical composition of the individual macerals in the individual coals concerned.Kaolinite is the most abundant of the minerals in the coals studied, with lesser but still significant proportions of quartz, mica and/or illite, dolomite, calcite, and pyrite. Small but variable proportions of anatase, goyazite, and siderite are present in some coal samples. Electron microprobe analysis, based on a special configuration for light-element study, shows that the vitrinite contains less carbon and more oxygen, and has significantly higher concentrations of nitrogen and organic sulphur, than the inertinite macerals in the same samples. Minor proportions of organically-associated inorganic elements, including titanium, were also identified in some of the maceral components.A comprehensive knowledge of the minerals and non-mineral inorganic elements in the coals used for feedstock preparation, obtained by integration of data from these advanced analytical techniques with more conventional analyses, may be of benefit in understanding the processes that take place during coal utilization, and also in avoiding or ameliorating some of the operational and environmental problems that may occur in different sectors of the coal utilization industry."

Jan 1, 2016

By J. Githiria, C. Musingwini

"Cut-off grade is a decision-making criterion often used for determining the quantities of material (ore and waste) to be mined, ore processed, and saleable product. It therefore directly affects the cash flows from a mining operation and the net present value (NPV) of a mining project. A series of different cut-off grades that are applied over the life of mine (LOM) of an operation defines a cut-off grade policy. Due to the complexity of the calculation process, previous work on cut-off grade calculation has mostly focused on deterministic approaches. However, deterministic approaches fail to capture the uncertainty inherent in input parameters such as commodity price and grade-tonnage distribution. This paper presents a stochastic cut-off grade optimization model that extends Lane’s deterministic theory for calculating optimal cut-off grades over the LOM. The model, code-named ‘NPVMining’, uses realistic grade-tonnage realizations and commodity price distribution to account for uncertainty. NPVMining was applied to a gold mine case study and produced an NPV ranging between 7% and 186% higher than NPVs from deterministic approaches, thus demonstrating improved project value from using stochastic optimization approaches. Background on cut-off grade calculation and optimizationCut-off grade is a decision-making criterion that is generally used in mining to distinguish ore from waste material. Consequently, it is used to determine the quantities of material (ore and waste) to be mined, ore processed, and saleable product. A series of different cutoff grades that are applied over the life-ofmine (LOM) of a mining operation defines the cut-off grade policy for that particular operation. The cut-off grade therefore directly affects the cash flows to be produced and the net present value (NPV) of a project at the mine planning or feasibility study stage."

Mar 1, 2019

By I. Ashmole

The dimension stone industry is not widely known or appreciated within the mainstream mining industry. This is in spite of the fact that the industry has grown at an average of over 7% per annum since 1980, and is estimated to now have a global turnover in excess of US$ 60 Billion per annum. Production technologies, particularly in the developed world where labour costs are high, have developed rapidly over the past two decades. Aligned with this, there has been a significant trend in adoption of a more professional mining approach in the exploration for and operation of dimension stone quarries. In fact, in the experience of the authors, mining a dimension stone deposit successfully if often more challenging from a mining engineering point of view than many conventional surface mines. This paper gives an overview of the industry and then proceeds to discuss best practice in exploration for dimension stone and to outline the latest technologies applied in mining of dimension stone. These technologies are varied and the specific combination of technologies applied in any given quarry is determined by both the physical properties of the material as well as the influence of geology which significantly impacts on the recovery of saleable material and hence the economics of the quarry.

Jan 1, 2008

By H. Edinger

China?s engagement with the African continent has increased impressively in the past decade. Even though China is not the African continent?s largest stakeholder, the rapidly increasing engagement is evident in the huge number of Chinese migrants that have come to Africa in the wake of unprecedented trade and investment levels, as well as in increasing diplomatic and political interactions, which has taken most other commercial partners by surprise. All but four countries in Africa have adopted the ?One China?1 policy stance; and in so doing opened the door for new or strengthened commercial dealings with China, including increasing investments into Africa?s extractive industries. This has been particularly evident since the turn of the century, with a clear shift in China?s policy towards Africa elevating the continent in China?s foreign policy objectives. As such, Africa has become a strategic focus2 for Chinese outward bound and internationalizing companies, especially in the extractive industries. This planned shift in focus is based largely on geo-strategic and commercial needs and interests, rather than previous ideological ones.3

Jan 1, 2011

By J. N. Van der Merwe

Following the Coalbrook disaster in 1960, research into coal pillar strength resulted in the adoption of the concept of a safety factor for the design of stable pillars in South African coal mining. At the time when the original statistical analysis was performed by Salamon and Munro in the early 1960s, 27 cases of failed pillar workings were considered suitable for inclusion in the database of failed pillars. Pillar failure did not stop after the introduction of the safety factor formula by Salamon and Munro (1967). In the ensuing years, pillars that were created before the application of the formula deteriorated and later failed, as did ones that were created after the introduction of the formula. This means that over time, the database of failed pillar cases increased in size, allowing ever more reliable analyses to be performed. The number of failed cases in the database had grown from the original 27 in the 1960s to 86 by 2011. All the failed cases are contained in the updated database. The database of stable pillars, which is also used in the derivation of strength formulae, has now been extended from 125 to 337 cases. The new database of intact pillar cases is more complete as it bridges the time gap between the Salamon and Munro (1967) and the Van der Merwe (2006) databases. The original requirements for inclusion into the database were satisfied in the compilation of this latest collection. The characteristics of the original database of intact pillars did not change in a meaningful way. The mining depth and pillar dimensions of the new database are largely as they were in the original database. Time-related trends with regard to pillar dimensions and depth of mining could not be found, indicating that the geometrical parameters of coal mining in South Africa have not changed meaningfully in approximately a century of mining. The characteristics of cases in the updated database of failed pillars does not differ substantially from the one published by Van der Merwe (2006). The same difference between that database and the original Salamon and Munro database, namely that the average safety factor of the failed cases had increased dramatically, from 1.0 to 1.5, is still apparent. This may be due to the inclusion of more failures from specific areas that exhibit a disproportionate number of failures at higher safety factors. These areas are the Vaal Basin, Klip River, and Free State coalfields. The new database confirms yet again that there is no correlation between the safety factors of failed pillars and their time of failure. The safety factor on its own is thus not a reliable predictor of longterm stability of pillars. Keywords coal pillar, stable pillar cases, pillar collapse, pillar data base.

Nov 1, 2013

By S. T. L. Harrison, A. Kotsiopoulos, J. R. Amaral Filho, J. L. Broadhurst

The land disposal of voluminous fine-grained tailings from the processing of mined ore bodies poses a long-term risk to the surrounding environment and local communities, while also representing a loss of valuable natural resources; including water, land and mined minerals. To date, the development and practical implementation of alternative approaches and technologies for removing risk and reducing the burden associated with these wastes, particularly in South Africa, remains limited, and value recovery is largely limited to the extraction of precious metals. To this end, researchers at the University of Cape Town have developed a programmatic multi-phased approach to explore and develop opportunities for the valorisation of large-volume mine wastes, based on the innovation value chain. This paper outlines this conceptual approach and presents key outcomes from its application for the specific case of sulfide-bearing coal processing wastes from South African collieries. Through the application of a combination of qualitative and quantitative tools and methodologies, a number of potentially viable opportunities and processing routes for value recovery and bulk re-purposing of these wastes have been identified and tested on a laboratory scale. Studies have, however, also shown that there are several technical and non-technical factors currently constraining commercial application of these opportunities. Overcoming these constraints will require a commitment to innovative waste management approaches and effective multi-sectoral collaboration. Keywords: Coal processing wastes, physical separation, waste re-purposing and utilisation, technology transfer

Jan 1, 2020

By T. Feroze, B. Genc

"Blind headings in room and pillar coal mines are a major source of methane and coal dust. Most methane and coal dust explosions therefore occur in the blind headings. The primary cause of these explosions is the disruption of the local ventilation system. Line brattice (LB) ventilation systems are used to ventilate blind headings by directing air from the last through road (LTR) into the heading. The amount of air available to ventilate the face of the empty heading depends on the heading dimension, settings of the LB, and velocity of air in the LTR. LBs are commonly installed by underground supervisory staff based on work experience, which may result in ineffective ventilation. The correct installationof LBs remains a challenge. In this study, a validated computational fluid dynamics (CFD) model has been used to analyse the effect of the LB ventilation system variables on the air flow rates close to the face of the empty heading. Full-scale three-dimensional models with various heading heights, heading depths, LB settings, and LTR velocities were simulated. The air flow rates and patterns at various locations inside the heading were analysed. A comparative study was carried out to quantify the effect of each of these system variables on the flow rates close to the face of the heading. Based on the findings, a user-friendly numerical model was formulated that can be used to estimate the flow rate close to the face of an empty heading for different practical settings of the system variables. This model can help the supervisory staff to swiftly implement the ventilation plan according to the regulations and the mine standards. The model can also serve as part of the curriculum for educating future mining engineers."

Jan 1, 2017

By T. Feroze, B. Genc

"Blind headings in room and pillar coal mines are a major source of methane and coal dust. Most methane and coal dust explosions therefore occur in the blind headings. The primary cause of these explosions is the disruption of the local ventilation system. Line brattice (LB) ventilation systems are used to ventilate blind headings by directing air from the last through road (LTR) into the heading. The amount of air available to ventilate the face of the empty heading depends on the heading dimension, settings of the LB, and velocity of air in the LTR. LBs are commonly installed by underground supervisory staff based on work experience, which may result in ineffective ventilation. The correct installation of LBs remains a challenge.In this study, a validated computational fluid dynamics (CFD) model has been used to analyse the effect of the LB ventilation system variables on the air flow rates close to the face of the empty heading. Full-scale three-dimensional models with various heading heights, heading depths, LB settings, and LTR velocities were simulated. The air flow rates and patterns at various locations inside the heading were analysed. A comparative study was carried out to quantify the effect of each of these system variables on the flow rates close to the face of the heading. Based on the findings, a user-friendly numerical model was formulated that can be used to estimate the flow rate close to the face of an empty heading for different practical settings of the system variables. This model can help the supervisory staff to swiftly implement the ventilation plan according to the regulations and the mine standards. The model can also serve as part of the curriculum for educating future mining engineers."

Jan 1, 2017