Search Documents

By S. Durapraj, R. T. Masethe, U. Maqina, A. C. Adoko

This study investigates seismicity and rockburst control within the Merensky Reef and UG2 orebody of an intermediate-depth platinum mine located in South Africa's Bushveld Complex. Utilising a mine-wide seismic monitoring system, over 1,900 seismic events were recorded between April 2023 and May 2024, revealing complex seismic patterns driven by mining-induced stress changes. The largest event, with a magnitude of ML 2.0, underscores the seismic risks associated with mining at increasing depths. Key findings include the spatial and temporal variability of seismic events, with high seismic activity observed near pillars and geological structures. A significant portion of events correlated with pillar and foundation failures. Moment tensor analysis identified dominant failure modes, such as stress-driven fracture closures and dynamic pillar failures. To mitigate risks, the study emphasises advanced support system redesign and rockburst risk assessment using the rockburst damage potential (RDP) method. The research highlights the importance of monitoring, geotechnical compliance, and adaptive designs in enhancing safety and reducing seismic hazards in underground mining operations. The study applied the RDP framework, classifying damage across R1 to R5 scales, where most instances fell into low-risk categories (R1 and R3), indicating minor to moderate damage. However, data limitations and the tabular stoping method's complexity led to inconclusive results, highlighting the need for more robust data and customised risk assessment tools. Despite these challenges, the RDP approach provided valuable insights into rockburst mechanisms and the effectiveness of existing support systems.

Jan 12, 2025

By S. T. L. Harrison, A. Kotsiopoulos, M. D. Maluleke, E. Govender-Opitz

In the extraction of base metals from printed circuit boards (PCBs) using bioleaching, the accumulation of metal ion stress in solution has been shown to inhibit the microbial regeneration of ferric iron. This poses a challenge for the development of this technology for e-waste treatment. The paper explores the application of a microbial immobilisation system in a two-stage bioleaching system consisting of a chemical leaching reactor in series with a microbial ferric iron regenerating reactor to mitigate microbial inhibition and to enhance base metal extraction. A mixed microbial culture dominated by L. ferriphilum, L. ferrooxidans and At. Caldus was maintained over a period of two months in the presence of polyurethane foam which acted as the biomass support particle. Microbial metabolic activity of immobilised cells and their tolerance to inhibitory Cu ions was investigated. Results showed that immobilised microbial cells maintained higher ferrous iron oxidation activity compared to planktonic cells in the presence of increasing Cu2+ concentrations up to 6 g/L. This presents an opportunity for microbial immobilised systems to be adopted in two-stage bioleaching system. Keywords: Bioleaching, microbial immobilisation systems, microbial inhibition and ferrous iron oxidation

Jan 1, 2020

By J-C. Lv, S. Zhao, F-L. Zhang, T. Yan

"To eliminate nozzle clogging during continuous casting of ship plate steel and reduce the calcium addition required, the composition of CaO-MgOAl2O3 inclusions in the liquid phase region must be controlled. Thermodynamic calculations using FactSage show that when the balanced Al content is 0.03 mass %, aCa in the liquid steel is 1–10 ppm, and aMg is 0.01–0.3 ppm; and when the balanced Al content is 0.06 mass %, aCa in the liquid steel is 1–30 ppm, and aMg is 0.05–0.9 ppm. The CaO-Al2O3-CaS inclusions can be controlled in the liquid region below 1600°C at aCa values of 5 ppm, 15 ppm, and 30 ppm, and the balanced Al content should be controlled in the range of 0.001–0.050, 0.005–0.250, and 0.010–0.50 mass %, respectively. Based on theoretical analysis, the refining slag composition should be controlled to 45–53 mass % CaO, 30–37 mass % Al2O3, 6–12 mass % SiO2, and 6–8 mass % MgO. Optimization of the slag system and steel composition can reduce, or even eliminate, the requirement for calcium treatment. The total oxygen content in the slab can be controlled to 15–21 ppm, with typical micro-inclusions ??10 ??m in size, with compositions in the CaO-Al2O3-MgO and CaO-Al2O3-CaS systems. Introduction With the rapid growth in steel output in China and the changes in the macroeconomic environment, competition in the steel industry has become more intense. The technology for economical cleaning of high-grade steel is important for improving product quality and reducing production costs. However, the functions of refining equipment have not been fully taken into consideration, and the combination of refining methods has not been optimized completely. These problems have become a bottleneck, restricting modern steel enterprises from developing an economic clean steel production process. Ship plate steel produced by the converter long process has been selected as the example in this study. The composition of the steel is shown in Table I. This steel is a high-strength low-alloy steel for rolling media and heavy plates, mainly used for ocean-going vessels and other steel structures. The carbon content in the steel is far from the peritectic point, and the crack sensitivity of the slab surface is weak, so impurities and gas content are strictly limited. Therefore, the process route BOF (basic oxygen furnace) – LF (ladle furnace) – CC (continuous casting) needs to be studied."

Jan 1, 2018

By Y. Yang, L. Li, X. Liu

Coal mining in China is facing the transition from output to quality. Based on the total mining capacity and average production, the current situation of coal mining at mine, city, and province levels is analysed, and data in support for the layout of sustainable mining development and the optimization of output provided. The results show that 87% of China's coal is mined by underground methods, with an average production capacity of 0.93 Mt/a per mine. Open pit mining accounts for 13%, with an average mine production capacity of 5.73 Mt/a. The average mining capacity of coal mines in China is 1.05 Mt/a, with 1181 coal mines with an average capacity less than 0.3 Mt/a, accounting for 35% of the total coal mines but contributing only 4.51% to output. They are distributed in about 48 cities in six provinces, seriously restricting the transition to green coal mining. The coal industry should speed up the closure of small coal mines in key provinces and cities, eliminate outdated production capacity in the central region, increase the speed and proportion of coal resources moving westward, and promote high-quality development of coal mining.

Jan 26, 2023

By K. Thambi

"A recent amendment to Section 36(11)(e) of the Income Tax Act, 53 of 1968 (Tax Act) now extends the allowable deduction of ‘capital expenditure’ incurred by mining companies pursuant to the Mineral and Petroleum Resources Development Act 28 of 2002 (MPRDA). In terms of the Taxation Laws Amendment Bill 2016 (TLAB 2016), the allowable deduction has been extended to include expenditure incurred on infrastructure in terms of Social and Labour Plan (SLP) requirements as per the MPRDA. Interestingly, what necessitated the amendment was the need to recognize SLP requirements and to circumvent administrative difficulties for mining companies and the South African Revenue Services (SARS) in differentiating the use of developmental infrastructure by employees or the community. The successful implementation of such a deduction hinges on a sound SLP system. However, given the challenges within the current SLP system, this amendment could be considered somewhat premature. IntroductionSection 36(11) of the Income Tax Act 58 of 1962 (Tax Act) enabled mining companies to deduct certain capital expenditure in lieu of its other sections. In particular, it made provision for mining companies to deduct capital expenditure incurred pursuant to the Mineral and Petroleum Resources Development Act 28 of 2002 (MPRDA), but excluding capital expenditure incurred in respect of infrastructure or environmental rehabilitation. As such, mining companies could only deduct such capital expenditure that related directly to their employees and not to the wider community (Clegg, 2018).In terms of the Taxation Laws Amendment Bill 2016 (TLAB, 2016) (South Africa, 2016a), the recent amendment to Section 36 extends the relief provided under section 36(11)(e) to include capital expenditure incurred on infrastructure in terms of the Social and Labour Plan (SLP) requirements of the MPRDA. In other words, the capital expenditure incurred by the mining company for the benefit of the people living in mining communities. To qualify for such a deduction, the infrastructure erected or developed by the mining company should reflect what was agreed between the mining company and the Department of Mineral Resources (DMR) as per the SLP requirements of the MPRDA (TLAB 2016)."

May 1, 2019

By D. J. de Clerk

Global trends stipulate the need to optimize existing assets while reducing environmental impacts. This paper illustrates the procedure that was followed to achieve such goals at one of the coal burning flash dryer units at an Anglo American smelter. An in-depth study of the process and related literature led to the development and installation of a revised control philosophy. This system includes modifications to the existing regulatory control structure as well as a hybrid rule-based and model-predictive advanced process control (APC) layer. Since commissioning of the APC, this flash dryer?s average throughput has increased by more than 6%, despite higher feed moistures. Furthermore, even though coal consumption has increased slightly, operating efficiency has improved by close to 5%. This was made possible by improving stability of the drying column outlet temperature by approximately 40%, which in turn enabled selection of a more optimal setpoint. Recent data has shown that APC utilization now exceeds 95%. This is indicative of a successful controller installation with good site acceptance. The same philosophy has therefore since been rolled out to most of the other flash dryers in the group.

Jan 1, 2012

By L. G. Austin

The paper summarizes the current state of development of simulation models for SAG and FAG mills, and gives the results of recent investigations of the physical processes occurring in autogenous grinding. The breakage process is treated as the sum of three regions of breakage actions: normal breakage caused by nipping of particles between media (steel balls or pebbles); abnormal breakage caused by media when the particle or lump is too big in relation to the media to be readily nipped; and self-breakage resulting from the chip¬ping fracture and abrasion of the tumbling action of rock lumps. Each region of breakage action has associated specific rates of breakage and primary progeny fragment distributions. A simplified form of the model was used to predict the performance of an 8 m diameter SAG mill with L/D = 0.5 grinding a copper ore, and predicted maximum capacity and minimum kWh/ton at about 6% ball load at 25% total filling. Two FAG mills of L/D = 2 were necessary to give the same capacity, and the simulations indicated a lower kWh/ton for these mills. For this ore, both systems were technically feasible.

Jan 1, 1987

By J. H. Selby

The Southern African Institute of Mining and Metallurgy hosted the 6thInternational Heavy Minerals Conference at the Zulu Nyala Game Lodge near Hluhluwe in Zululand, during September 2007. This series of conferences has run for 10 years and has been held on three continents. The interest that has been shown in the conference over the years has demonstrated that the field of heavy minerals is a dynamic and profitable one. It is perhaps appropriate that the tenth conference was held in Zululand, South Africa, where it had its roots. The conference theme was ?back to basics?, and this implied revisiting many of the technologies that made this industry a great one. In doing so, we got a view of how those basic technologies have been put to new applications. There were 39papers accepted for the conference, covering all aspects of the industry. These were presented over a period of four days. This edition of the Conference Proceedings provides the reader with a permanent record of these papers. We hope this volume will join the other five, which this series of conferences has produced, and give a lasting record of the development of our industry.

Jan 1, 2007

The comments by Mr Chaston were constructive and much appreciated. Considering firstly the recovery of cassiterite from fine deslimed material. A size distribution analysis shows that 58 per cent of cassiterite in Union Tin flotation concentrate reports in the minus 15 micron (quartz) size range. This is achieved at a recovery of 67 per cent and concentrate grade of 42,6 per cent. It is of interest to note that at Altenberg in East Germany 85 per cent of the tin in deslimed minus 43 micron material is recovered into a 14 to 16 per cent Sn concentrate using para-tolyl arsonic acid as collector. Reconcentration of this material is then carried out using two shaking table stages which recover 53 per cent of the tin in a 50 per cent Sn concentrate. Flotation was resorted to after recovery rates of 35 per cent and concentrate grade of 30 per cent had been achieved in a 275 ton per day plant comprising 130 tables. Tests on tabling of deslimed minus 43 micron material have not been carried out at Union Tin. The cost of equipment actually associated with cassiterite flotation amounts to about R60 000. The

Notices TRANSPORTATION AND THE ENVIRO NMENT The 5th Quinquennial Convention of the S.A. Institution of Civil Engineers will take place at the Carlton Centre, Johannesburg, from 20th to 24th August, 1973. ENVIRONMENTAL ENGINEERING A conference on environmental engineering problems in industrialized and developing countries is to be held at the United Engineering Centre, New York, on 19th and 20th September, 1973. RABCEWICZ-COLLOQUY The Austrian Society for Geomechanics is to honour Professor Ladislaus V. Rabcewicz, on the occasion of his 80th birthday, with a meeting in Salzburg Congress Hall on 11th and 12th October, 1973. The themes of the four half-day sessions will be as follows. PYRO MET ALL URG ICAL EVENTS IN 1974 Diisseldorf is to be the venue for the following three events: International Iron and Steel Congress O.F.S. Branch Welkom THE MARCH GENERAL MEETING OF THE BRANCH WAS HELD IN THE ST. HELENA CLUB AT 8.00 P.M. ON TUESDAY, 6TH MARCH, 1973 O.F.S. Branch Welkom MINUTES OF A GENERAL MEETING HELD IN THE ST. HELENA CLUB ON WEDNESDAY, 16TH MAY, 1973, AT 8.00 P.M.

By T. Bhambhani, E. Arinaitwe

Solvay has developed several novel reagent innovations to improve separations in sulfide ore flotation and address major industry challenges. These innovations include: a) carbon management strategies to reduce the deleterious impact of organic carbon on flotation circuits; b) new collectors for heavily tarnished or oxidized Cu-Au ores; and c) a functionalized depressant for minimizing penalty elements in metal concentrates. Owing to their unique chemistries, these innovations exhibit a wide spectrum of rather unique properties that are quite in contrast to the traditionally used reagents. The chemistry, attributes, application, and advantages of these innovations are discussed in this paper based on laboratory, pilot, and plant results and observations for various ores

Jan 1, 2023

By S. Tshikhudo

This paper outlines an investigation into the recovery of saleable fractions of coal from ?as-arising? South Export Plant effluent streams, using Baleen microscreening technology. South Export Plant, a subdivision of BHP Billiton Energy Coal SA (BECSA) Coal Processing, is a two-module plant treating 2000 t/h. The nominally -150 µm coal is untreated and is therefore passed from classifying cyclones to the thickeners for process water recovery. The thickened underflow is pumped into a series of slurry cells for further settling and recovery of supernatant water. The marginal quality, moisture content, and handlebility of this settled material renders it unsuitable for inclusion into saleable products and it is thus stockpiled and trucked to designated pits for disposal. Over the years, stockpiling and trucking has become an overly expensive exercise. In an effort to recover some of this cost, a task team was assigned to investigate less costly options to process slurry across BECSA plants. Various technologies such as froth flotation, sieve bends, and Reflux Classifier were considered, although the results were generally not beneficial ? this could be attributed to weathered/oxidized coal. A decision was made to pursue an alternative approach by testing the suitability of the new ?Baleen Filter?. The concept is to screen out the higher-grade fraction (+50 µm) as saleable product and reject the finer fractions to the slurry ponds. The Baleen Filter was found to effectively screen at an acceptable efficiency between 94% and 99.99%, with a very sharp cut-point (d50 and Ep). The actual yields from the screening results were better than the predicted yields in terms of both mass and energy as predicted from feedstock analysis.

Jan 1, 2014

By S. Banisi, S. M. Mousavi, S. D. Tafvizi, Gh. A. Parsapour, M. Mahmoudi

Generally, regrind circuits are used to increase the degree of liberation of value minerals which are fed to flotation circuits. At the regrind circuit of the Sarcheshmeh copper complex, four ball mills are in closed circuit with their hydrocyclone clusters. In the initial design of the plant, feed and underflow percent solids, and pressure drop of the hydrocyclones were 39% and 65%, and 15psi, respectively. Over the years, due to a reduction in the feed grade from 1.17% to 0.67% and changes in the operational conditions, the feed rate to each hydrocyclone cluster has decreased from 401 to 70t/h and consequently the pressure drop, feed and underflow percent solids have reduced to 4psi, 17% and 25%, respectively. The main objective of this research was to audit the feed solids concentration and pressure drop of the hydrocyclones and make the necessary modifications based on the Plitt’s model. The results of sampling showed that water recovery to underflow was 59% which was higher than normal values. By reducing the number of operating regrind mills from 4 to 2, the feed rate to each mill increased. After this modification and taking necessary measures in the plant to implement the new operating approach, the pressure drop, feed and underflow percent solids increased to 18psi, 28% and 58%, respectively. The water recovery of the hydrocyclones underflow decreased from 59% to 12%. These changes in addition to increasing the circuit efficiency saved 1000 kWh energy and decreased ball consumption by 925 ton/year because of reduction in the number of operating ball mills. Keywords: Regrind mills, flotation, audit, troubleshooting

Jan 1, 2020

By B. Talbot

How this simple plant generates a large revenue stream. The concept behind the Tailings Scavenging Plant (TSP) is simple: it is a non-complicated modular plant which is designed to be more stable than upstream plants. This, plus the use of ?high energy?, enables the plant to recover any metal missed by the upstream operation. Impala Platinum?Mineral process started pilot plant exercises in June 2003. The pilot plant ran for one year before the capital for the full-scale plant was approved. This year was used to motivate, design and cost a full-scale plant. The metal produced during the pilot and feasibility study enabled this part of the project to run at a small profit. The scale-up to full-scale was relatively simple as the pilot plant had a capacity of 180 m3/hrand the full-scale plant was designed for a capacity of 550 m3/h. The design for the full scale plant was completed in May 2003, with ground breaking taking place on 19 May 2003. The construction phase of the project went well with the commissioning of the first two modules taking place on 22 October 2003. The remaining two modules were commissioned two weeks later. The plant was at full capacity by the 20 November 2003. A review of the plants performance for the first 5 production months is as follows: the plant has required only a few minor modifications and additions, it has run well in excess of 95%availability with no major wear apparent. In addition to this, the plant has produced 3 times the metal forecast.

Jan 1, 2004

Ninth International Symposium TECHNIQUES FOR DECISION MAKING IN THE MINERAL INDUSTRY The Symposium which is to be held in Montreal during the week of 14th to 19th June, 1970, follows the Computer Symposium held in Salt Lake City in September, 1969. The purpose of the Symposium is to define the role of decision-making techniques within the mineral industry and to stimulate the development of specific applications. The subject of the Symposium-mathematics, operations research and computers as applied to the mineral industry-have permitted us to structure it in such a way that a complete picture of the mineral industry in its public policy, corporate, financial and technological environment emerges. Topics for the sessions are: . The Public Policy Environment;. The role of Decision Making Techniques in the Mining Company; . Information Storage and Retrieval; . Markets-Forecasting, Patterns and Strategies;. Search for Mineral Deposits;. Quantification of Geological Variables;. The Mine Development Decision; Production Systems;. Planning, Scheduling and Control Systems. The sessions will be directed energetically by chairmen who have been in continuous contact with the authors, providing them with information about related papers and sessions. This symposium is sponsored by the Canadian Institute of Mining and Metallurgy, McGill University and Ecole Polytechnique. Further information may be obtained from: The 9th International Symposium. W. H. Gauvin, General Chairman, J. Elbrond, Programme Chairman. Department of Mining Engineering, Ecole Poly technique, P.O. Box 501, Snowdon, Montreal 248, Quebec, Canada. ACHEMA 1970 The European meeting of Chemical Engineering and the Achema Congress 1970 is being held at Frankfurt/Maine, from 17th to 24th June, 1970. The programme includes some 110 plenary and specialised lectures, numerous technical films, excursions, and technical discussions in front of the exhibits which form the central feature of the Achema-Exhibition Congress. Further information may be obtained from the honorary representative of Achema in South Africa, Mr F. Schilling, P.O. Box 31274, Braamfontein, Johannesburg. NINTH COMMONWEALTH CONGRESS PROCEEDINGS Publication of the proceedings of the Ninth Commonwealth Mining and Metallurgical Congress, 1969, is being undertaken by the Institution of Mining and Metallurgy, London. There will be four volumes covering papers presented at the Congress together with the discussion and author's replies, and the addresses by Sir Duncan and Sir Ronald Prain. These will be available April-June 1970. Special pre-publication prices apply to orders received before 1st April, 1970. Order forms may be obtained from Secretary S.A.I.M.M., P.O. Box 1183, Johannesburg. 6th World Congress on the Prevention of Occupational Risks This Congress, dealing with industrial accidents and occupational diseases, will be held in Vienna from 10th to 15th May, 1971. Further information may be obtained from: VI Weltkongress für Unfallverhütung, Postfach 745, A-1015 Wien, ÖSTERREICH. International Vacuum Metallurgy Conference 1970 The Vacuum Metallurgy Division of the American Vacuum Society is organizing an international meeting that will be held at the Convention Center in Aanaheim, California from 15th to 19th June, 1970. Enquiries should be directed to the Arrangement's Chairman, L. M. Bianchi, TRW Inc., 23555 Euclid Avenue, Cleveland, Ohio 44117, Tel. No. (216) 383-2111. AIME WORLD LEAD-ZINC SYMPOSIUM This symposium is being held from 21st to 23rd October, 1970, in St. Louis, Missouri, U.S.A., in conjunction with the Fall Meeting of the Society of Mining Engineers, and a Rapid Excavation Conference. In addition to local field trips to smelter and refinery operations there will be a number of extended trips of six to eight days. Information may be obtained from: Mr. John C. Fox, Secretary, Society of Mining Engineers of AI.M.E., 354 East 47th Street, New York, N.Y. 10017, U.S.A. NEW SUBSCRIPTION RATE TO THE JOURNAL As from 1st JANUARY, 1970, the subscription rate for the Journal has been increased from R12.00 to R18.00 per annum, i.e. R1.50 per issue instead of R1.00. The discount to booksellers is 15 per cent. COURSEOF THE THEORYOF THE UNIT OPERATION OF GRINDING The South African Institute of Chemical Engineers is arranging for Prof. L. G. Austen to conduct a course on the above subject in September, 1970. Interested persons should contact Dr G. S. Harrison, S.A. Institution of Chemical Engineers, A.E. & C.I., 15 Anderson Street, Johannesburg. METRICATION The S.A. Bureau of Standards has published a document entitled "Metric Scales and Units for use in the Building and Construction Industry." It has been compiled by the Metrication Committee of the National Building and Construction Advisory Council and is the first of the series of informatory documents relating to the programme for the metrication of the Building Act Construction Industry. This document is obtainable from the South African Bureau of Standards, Private Bag 191, Pretoria at 50c per copy.

A General Meeting and Colloquium was held in Kelvin House, Johannesburg on Wednesday 29th September, 1971. The theme of the Colloquium was "The Ferro-alloy Industry". Prof D. D. Howat (President) was in the Chair. The meeting was attended by 106 delegates and was opened by the President at 10.05 a.m. OBITUARY The President: "It is my sad duty to announce the death of G. C. Needham, Fellow, who joined the Institute in 1966 and passed away on 27th September, 1971. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments silence." MEMBERSHIP The President: "I have much pleasure in announcing that the names of the following candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute. Fellows: Richard Lloyd Blandy, Brian Roger Borton, Brian Teversham, Peter Donald Dickson. Members: Frederick Brian Peacock, Peter John Stacey, Kenneth Niles Thanstrom, Byron J. Hayley, Ian Flemming Buchan, Abraham Hercules le Roux. Graduate: Ian William Coy. Students: Peter Boesley J ames, Kenneth Brian Perel. TRANSFERS From Member to Fellow: Cecil Eugene Fivaz, Peter Edwards. From Student to Graduate: Roy Stavely Traviss. From Student to associate: William Mitchell. I welcome the new members to the Institute and congratulate those members who have been transferred to a higher grade. COLLOQUIUM The first paper, presented by Mr S. Selmer-Olsen, Consulting Metallurgist, Amcor Limited, on 'Trends in Ferro Alloy Production' was published in the May issue of the Journal and comprised information and data relating to new developments in ferro alloy production in various parts of the world. This was followed by a paper-'Conductivity and Viscosity Properties of Slags produced in ferro-alloy manufacture' by D. 1. Ossin et al. This was a record of laboratory test work on slags containing both lime and magnesia, corresponding with the composition of slags encountered in the production of ferro chrome alloys when a dolomite flux is employed. The third paper-'Review of the work of the Pyrometallurgical Research Group of N.I.M. and Metallurgy Department, Wits.' presented by Dr P. R. Jochens, leader of the Research Group, outlined the progress made on ten different research projects presently under way in the Department of Metallurgy. These projects range from studies of the kinetics and mechanism of the reduction of chromite ores through the determination of the activities of MnO in slags to phase studies and melting point determinations in the alloy systems Cr-Fe-Si-C and Cr-Fe-Si. A new feature of this Colloquium was the introduction of the discussion panel composed of four or five individuals known to have special knowledge or interest in the subject under duscussion. Mr J. J. Coetzee was chairman of the first panel, Professor D. D. Howat of the second and Dr R. E. Robinson of the third. During the discussion of Mr Selmer-Olsen's paper an interesting contribution was made by Mr Jack Hayley of Transalloys (Pty.) Limited who pointed out that the lowest power cost in the U.S.A. was that from the TV A at 6 mils per unit (0,43 cents S.A.) while costs from other sources were 7 to 8 mils per unit (0,50 to 0,57 cents S.A.) He also referred to the use of 'pile sintering' of ore fines plus coke at certain ferro alloy plants in the V.S. and to the recent practice of 'graphitising' the paste used for Soderberg electrodes. The last session in the afternoon was devoted to a group discussion on 'Practical problems in Arc Furnace Operation', Mr H. R. Reid of Middelburg Steel Alloys (Pty) Limited occupying the chair, members of the panel being Mr J. Meintjies (Rand Carbide Limited), Mr J. Benn (Amcor) and Mr E. J. Jackson (Transalloys (Pty.) Limited). Mr Reid initiated the discussion by talking of the design and composition of electrode shoes, mentioning the use of the 85/15 Cu/Zn alloy and the comparison of hollow shoes and shoes cooled by tubes. Mr Meintjies discussed electrode management with particular reference to breakages, and dealt with casing and fin design and the welding of fins. Mr Benn dealt with aspects of closed top furnace operation with particular reference to the control of eruptions in the furnace and indicated that preheating of the raw materials might be well worth considering together with the development of a system for the detection of the water vapour present. Mr J ackson was concerned with shells, linings, refractories and tap holes. He deprecated the use of oxygen for opening the tap hole emphasising how uncontrolled use of oxygen led to loss of shape of the tap hole and quite severe burning out of the front hole resulting in time and labour in repairs. A notable feature of the Colloquium was the free discussion 'from the floor' of the hall. Many valuable and highly pertinent contributions were made spontaneously and usually in reply to some controversial topic raised by the discussion group.

By C. R. S. Needes, M. J. Nicol, G. T. W. Ormrod, N. P. Finkelstein

The industrial application of a dioxide electrode uranium by C. R. S. NEEDES, Ph.D. (London) (Visitor), M. J. NICOL, Ph.D. (Rand) (Visitor), N. P. FINKELSTEIN M.Sc. (Rhodes), Ph.D. (Liverpool) (Fellow), and G. T. W. ORMROD (Visitor) A correlation between the potential of a U02 electrode and the rate of recovery of uranium has been proved in laboratory and plant trials. When the recovery rates change because of variation in the concentrations of Fe(III), Fe(II), SO4 'and H+, a positive correlation is observed. However, an 2- increase in the concentration of phosphate in solution produces an increase in the U02 electrode potential but a decrease in the rate of leaching of U02. The correlation between the U02 electrode potential and the rate of leaching of U02 is then negative. It is concluded that, as a control device, the electrode cannot compete with the platinum electrode for use on certain plants. Nevertheless, the U02 electrode will act as a useful warning device if the total concentration of iron in solution decreases to below a level concomitant with the economic recovery of uranium. Furthermore, because of the positive correlation between the U02 electrode potential and the phosphte concentration, the electrode will also be of value in the detection of an increase in the phosphate level in solution. When it was incorporated in a suitable industrial probe, the electrode was found to be able to withstand the rigours of the leaching conditions in a large pilot-plant pachuca, and only failed after six weeks' operation.

Jan 11, 1975

By R. P. King

The University of the Witwatersrand (Wits) and the minerals industry of South Africa have grown with the city of Johannesburg. The former has provided teaching and research in mining and metallurgy, while the latter has been responsible for the practical training of metallurgists and for the testing and implementation of innovative ideas proposed by the academics. This interplay between inventiveness and industrial application is illustrated by three examples: the establishment of the iron and steel industry as a result of the persistent experimentation undertaken by Professor G. H. Stanley, the first Professor of Metallurgy and Assaying at the South African School of Mines, which later became Wits; the establishment of the research organization that eventually became the Council for Mineral Technology (Mintek) - again through Professor Stanley's faith in the role of research; and the establishment at Wits of physical metallurgy as a discipline in its own right, as first suggested by Professor C. E. Mavrocordatos of Wits against the opinion of his colleagues in the industry. The Department of Metallurgy at Wits has been well supported by the minerals industry. Not only does the industry provide grants for the financial support of students, but it supplements the salaries of personnel in the Department, making possible the recruitment of top-class academic staff. At present the greatest problem is the lack of interest shown by matriculants in the metallurgical industry as a career. However, an enormous effort is being made by the Chamber of Mines, The South African Institute of Mining and Metallurgy, and the Wits Department of Metallurgy to ensure that matriculants receive appropriate information about the career prospects in the minerals industry.

Jan 1, 1983

National Coal Board. Gate belt conveyors. London, H.M.S.O. (Price 95p.) Although the preface of this handy little book states that it has been written for the guidance of miningoperation trainees, it will prove valuable to the practising engineer as well. NIM reports Report no. 1733 A mineralogical investigation of weathered carbonatite from Salpeterkop. (14th Apr., 1975; re-issued 28th Feb., 1978). Report no. 1823 The recovery of gold and pyrite from a residue dump at Crown Mines. (10th Jul., 1976; re-issued 28th Feb., 1976). Report no. 1829 An investigation of weathered carbonatite from Salpeterkop. (20th Jul., 1976; reissued 28th Feb., 1978). Report no. 1932 A BASIC computer programme for the evaluation of intensity data from the Telsec Lab-X-250 Analyser. (12th Jan., 1978). Report no. 1940 The extraction of the noble metals with n-octylaniline,and its application to the analysis of platinum-bearing materials. (30th Jan., 1978). Report no. 1945 Analyses of the NIMROC reference samples for minor and trace elements. (28th Feb., 1978). International futures conference A conference entitled 'The Road Ahead' is being organized by the 1820 Settlers National Monument Foundation to be held in Grahamstown from 3rd to 7th July, 1978. Conference of metallurgists The technical programme has been established for the 17th Annual Conference of Metallurgists sponsored by the Metallurgical Society of the Canadian Institute of Mining and Metallurgy. This year the Conference will be held in Montreal, Quebec, on 27th to 31st August, 1978, together with the 8th Hydrometallurgy Meeting.

Jan 1, 1978

By G. G. Rogers, A. Vna Der Linde, N. B. Strydom, W. H. Van Der Walt

Changes in the level of serum vitamin C in mineworkers by N. B. STRYDOM, M.Se., Ph.D. (Illinois) (Fellow), G. G. ROGERS, M.Se. (Pta) (Visitor), W. H. VAN DER WALT, B.Se. (Poteh.) (Visitor), and A. VAN DER LlNDE, B.Se. (O.F.S.) (Visitor) The levels of serum vitamin C in the blood of mineworkers were determined on the first and fifth days of the normal heat-acclimatization period (i.e., before and after exposure to heat) and again after I, 2, and 4 months of underground employment. Supplementary vitamin C was administered to the men during the heat-acclimatization period. Six groups of 20 men featured in the study and, except for one of the two 4-month groups, all the values were obtained after a full shift of underground work. It was found that adequate levels of serum vitamin C were maintained during the heat-acclimatization period, and the 250 mg of vitamin C given daily to each man must therefore be regarded as sufficient. The serum vitamin C decreased significantly with time of exposure to underground conditions, showing that the vitamin C utilized during heat stress is more than that provided in the men's diet. At the end of 4 months, not a single subject had more than 0,4 mg of serum vitamin C per 100 ml, most of them having only 0,3 mg per 100 ml; 90 per cent of the men had had more than 0,4 mg per 100 ml during the acclimatization period. It is therefore recommended that the mineworkers' diets should be supplemented with 100 to 200 mg of vitamin C per man per day.

Jan 5, 1977