Search Documents

By J. Jacob

Diamondiferous linear beaches in Mining Area No. 1 have been the mainstay of Namdeb?s diamond production for more than 80 years. Most of the onshore beaches have been mined out, but in recent years mining has been extended offshore into the surf zone through a process of beach accretion. A total of 61.6 million carats has been produced from the gravel beaches since their discovery in 1928, and Mining Area No. 1 is considered to have great remaining potential from areas currently submerged under water. To date, the surf zone has remained largely unexplored due to the consistently strong winds, currents, and large waves which make access to this area extremely difficult. This paper describes the processes used in developing a practical methodology for exploration of the surf zone in a domain extending approximately 22 km long in a northwest?southeast direction and 0.3 km wide in a perpendicular direction adjacent to the current Mining Area No 1. The vigorous surf zone poses multiple technical challenges in terms of obtaining geological and diamond information. In order to access the area for sampling, a jack-up walking probe drill platform (PDP) with a 5-inch diameter reverse-circulation drill has been developed to carry out exploration drilling in the dynamic surf zone. The hydraulically driven platform has eight legs, each of which is 18 m long. Four of the legs are in fixed positions on the fore and aft sides of the platform. The other four moveable legs are fitted to sliding frames attached to the port and starboard sides of the platform. The sets of fixed and moveable legs can be raised and lowered by hydraulically powered jacking stations. By alternately lifting and lowering the sets of fixed and moveable legs in conjunction with the frames moving back and forth horizontally, a walking action is performed by the PDP. The platform can walk at a speed of 10?15 m/h, depending on weather and footwall conditions. Optimization of sampling for diamondiferous gravel occurrence in Mining Area No.1 was undertaken through creation of a virtual orebody on which different sample configurations were tested. The input data for the construction of a virtual orebody comprises a set of drilling data, collected from recently accreted areas directly adjacent to the 22 km × 0.3 km target domain. The input drilling data covers only 34% of the domain, and for the purpose of this study, a single realization is deemed to be sufficient. The texture obtained from using only the drilling data to construct a simulation did not make geological sense; hence it was necessary to make use of analog data in order to improve the simulation. The first analog data used consists of the gully patterns found in the metasedimentary Precambrian bedrock footwall. Gullies are, in general, gravel filled and it is fair to assume that gully patterns form a subset of the total gravel occurrence. Total gravel occurrence includes marine terraces (governed by sealevel stands) above bedrock peaks, together with gravel within gullies below bedrock peaks. The second analog ?data? introduced is through the use of ?expert interpretation?. The indicator drilling data is interpreted by expert opinion and the 2-dimensional result is hand-sketched, digitized, and then pixelated. The pixelated data set is then used as input for variogram calculation. This study cannot provide a single definite optimization result as the nature of the data does not permit this. The use of different validation approaches (conditioning data, where available; expert interpretation; and gully pattern data), however, can give a very good indication of how to balance sampling effort with de-risking aspects related to geological continuity. Work undertaken by sampling the simulation will give an assessment of the relative probabilities of determining gravel occurrence in the study area. This study showed that a 50 m × 400 m cross-configuration will be a good initial sample spacing for highlighting areas where gravel may be absent, and further infill drilling may be required. The relative efficiency of a 50 m × 400 m cross off-set sampling configuration has been demonstrated using a trumpet curve versus sampling effort when using kriging as the estimation method. Keywords sampling configuration, marine diamonds, orebody simulation.

Jan 1, 2014

By I. Y. Motovilov, S. A. Telkov, M. B. Barmenshinova, Z. S. Abisheva

As a rule, removing waste rock at the beginning of the process improves the conditions for the flotation of minerals, and also reduces the operating costs of crushing, grinding and flotation. Lead-zinc ores in the Shalkiya deposit of the Republic of Kazakhstan are classified as difficult for enrichment, but taking into account their significant reserves, they are one of the main potential ores for the production of lead and zinc. Under industrial conditions, for processing ores of the Shalkiya deposit, a selective flotation concentration scheme with the production of lead and zinc concentrates is recommended. However, according to the recommended scheme, it is not possible to obtain high-quality concentrates of lead and zinc, with high metal recovery. The paper presents the results of studies of preliminary gravitational enrichment of lead-zinc ore in the Shalkiya deposit. Based on the fractional analysis for the particle size range of -40+8 mm, Henri- Reingard enrichment curves were constructed, separation density (2730 kg /m3) was established to isolate the light fraction with the lowest possible lead and zinc content, and gravity enrichment indices (0.7-0.71) were determined. It was found out that when using gravitational enrichment of the original large-sized ore in the Shalkiya deposit, tails are released at the beginning of the technological process with a yield of up to 20% with the extraction of silica up to 30%, calcite up to 11% and carbonaceous matter up to 12%. As a result of the studies, it was found that the beneficiation of crushed lump ore could be conducted in heavy suspensions. One of the positive aspects of the use of gravitational enrichment is the reduction of energy costs for grinding the heavy fraction, which was experimentally proved in this article. Keywords: Lead-zinc ores, Shalkiya deposit, fractional analysis, gravitational enrichment, floating fraction, sunken fraction, separation density

Jan 1, 2020

By S. O. Bada

Coal is a complex mixture of organic and mineral constituents and is the most abundant resource of fossil energy in the world. In recent years, significant research into dry coal beneficiation has gained much attention, primarily due to the need to improve grades and reduce the environmental contaminants in coal without the use of water, and to achieve this in as cost-effective manner as possible, relative to wet beneficiation processes. This paper seeks to review the application of various electrostatic separators with their process principles, to draw comparisons between different dry beneficiation techniques with specific emphasis on the tribo-electrostatic separation method, and finally to report the results of tribo electrostatic separation conducted on various South African coals. Previous research conducted on Indian, European and American coals has indicated that this technique is likely to lead to significant economic benefit through the reduction of ash content, NOx and more specifically Sox by separating out the liberated Fe-S-bearing minerals prior to utilization. The removal of the latter suite of minerals is also likely to significantly reduce or eliminate the emissions of associated trace elements, including mercury and arsenic. The research results reported in this paper indicate that the rotary tribo-electrostatic process has the potential for significant upgrading of high ash pulverized South African coal. The impact of various operational parameters was investigated and key factors established for the optimum recovery of low ash and low sulphur fine coal.

Jan 1, 2010

By M. Saghaeian, R. Hejazi, L. Hosseini, M. V. Sheikhzadeh

HPGR equipment has been well proven to be energy-efficient in the first stage of grinding in iron ore beneficiation plants. Numerous advantages of utilising HPGR grinding prior to ball mill grinding, such as reducing the power consumption in a ball mill through generation of micro-cracks, has been thoroughly studied. Less attention has been paid to efficiency of the HPGR circuit rather than the downstream ball mill circuit. In this study the HPGR circuit has been optimised through feed size reduction by crushing, and feed iron content upgrading by dry cobbing. This optimisation leads to better operation of the HPGR, and a smaller product size which is expected to result in a lower wear rate of ball mill liners and balls. It is also expected that the top size of the ball mill balls be reduced. Additionally, by reducing the feed size of HPGR from 30 mm to 15 mm, it is possible to achieve similar K80 of HPGR product in lowered pressure, i.e. 2.5 N.mm-2 instead of 3.5 N.mm-2 which translates to ease of operation. Similarly in a given roll pressure, smaller feed sizes result in higher specific throughput of ~10% which means higher production capacities. The results also reveal that this optimisation increases the concentrate weight recovery by about 10%. It also results in slight increases in the Fe grade of the product iron concentrate. Keywords: HPGR, HPGR circuit optimisation, crushing prior to HPGR, dry cobbing prior to HPGR, ease of operation, concentrate grade optimisation, weight recovery optimisation

Jan 1, 2020

By P. J. Le Roux

"Mining companies are under constant pressure to reduce their cost structures to sustain profitability. In mines using an open stoping mining method, dilution often has a significant effect on profitability. At Target mine in South Africa, dilution in some open stopes was found to exceed 10%, falls of ground being a major contributor to the problem. This dilution can reduce the recovered grade from 5.5 to 4.5 g/t, resulting in a potential loss of about R21 million per month based on a gold price of R240 000 per kilogram. In addition to the cost of dilution, the cost of damage to, or loss of, trackless equipment as a direct result of falls of ground in open stopes is significant. Other associated costs include transport, hoisting, secondary blasting, milling, and plant treatment of waste material. Stable open stopes are essential in order to reduce falls of ground. Back-analyses of stope instability at Target mine have indicated that conventional rock mass failure criteria are unsuitable for stope design. An alternative strain-based criterion has been developed, and has proved to be very successful, allowing the stability of open stopes to be calculated reliably. Since its implementation in 2010, dilution and equipment damage have decreased markedly, creating value for the mine. IntroductionMines that make use of an open stoping mining method aim to extract only the ore, leaving the waste behind. Many orebodies have well-defined boundaries between the ore and the waste rock. In such orebodies, the introduction of waste into the ore due to overbreak dilutes the grade. In massive disseminated orebodies, dilution is less problematic. Overblasting, falls of ground, or other causes may result in dilution. A study undertaken in Canada (Pakalnis et al., 1995) found that approximately 51% of all underground metal mines utilized open stoping mining methods and, from surveys conducted at these mines, open stoping operations experienced dilutions of up to 20%, and occasionally more. Dilution of this magnitude has a significant economic impact on any mining venture. Research carried out in Australia by Capes (2009) came to the same conclusion."

Jan 1, 2017

By R. T. Rudd

DISCUSSION R. T. RUDD I have the following comments on Mr Bosman's paper. Before giving the company permission to discharge neutralized mine drainage containing 1800 mg/l of dissolved solids into a public stream, my Department had to consider the matter from both the legal and the practical viewpoint.

Jan 4, 1974

By B. Oladipo, E. Govender-Opitz, T. V. Ojumu

Bioleaching, one of the several important processes of biohydrometallurgy is an accepted technique for the extraction of desired metals from sulphide ores. Although the mechanism is well understood, the slow metal extraction rate due to passivating layer and ferric ion precipitation, especially in a typical chalcopyrite leaching, impact negatively on the overall efficiency of the process. Iron precipitates are common in many biohydrometallurgical operations and these precipitates represent the exit route for undesired iron, alkali ions or sulphate ion from the processing circuit. While there have been reports on approaches to slow the formation of these precipitates by manipulation of various operating conditions such as pH, redox potential and temperature, the precipitates become highly significant over the long term in the continuous operation of bioleaching and may render heap impermeable. Although there is evidence supporting the nature of the passivation to be precipitates of iron, their scavenging mode of reducing extraction efficiency is still not well understood. This paper thus discusses iron precipitation in biohydrometallurgical processes, including its formation and significance on bioleach processes. The paper also details the associated passivating species identified with heap bioleaching of sulphide minerals and provides some insight into sorption mechanism that limits metal recovery in a typical bioleach operation. Keywords: Iron precipitation, bioleaching, chalcopyrite, passivation, jarosite, metal sorption

Jan 1, 2020

By N. Naude, R. Foisy, F. Bornman

Spiral separators have been widely accepted as one of the most flexible gravity separation devices for several decades. The International Journal of Mineral Processing, 84, pp. 118 – 132 mentioned that spirals are for treating material too coarse for flotation and too fine for dense-media separation. Powder Technology V 102, pp 244 – 252, 1999 stated that there exists a genuine need for extending the performance envelope of spirals – whether to treat finer or coarser material than the traditional size ranges. In recent times there has been an upsurge in interest, particularly in the development of newer fine gravity separators. Spiral separators for the recovery of ultra-fine particles have a unique profile, pitch and features to ensure efficient performance. The flow on the spiral trough must be controlled to minimise turbulence that will entrain fine particles in the outer section of the trough. The experimental test work showed a movement of mass from the outer region towards the centre column of the spiral, i.e., from the fine tailings band towards the concentrate. As recovery on the spiral trough is a function of mass yield and grade, the ultra-fine 7 spiral had a better recovery than the HX5. This makes the UF7 an ideal rougher spiral. Keywords: Ultra-fine particles, spiral, design, recovery

Jan 1, 2020

By X. Zhang, E. Li, Y. Xiao, Z. Yu, H. Han, J. Xie, J. Tian, W. Sun, K. Hong

In a pulp environment, the surface properties of magnesite and dolomite tend to be similar, due to the re-adsorption of dissolved calcium species, which makes the flotation separation difficult. In this paper, the chelating reagent EDTA is introduced to eliminate the adverse influence of the calcium species and to restore the selectivity of magnesite-dolomite separation using sodium hexametaphosphate (SHMP) as a depressant. Flotation experiments confirm that the recovery of magnesite improves significantly in the presence of EDTA. Zeta potential experiments confirm that the negatively charged EDTA4+ and HEDTA3+ species can form soluble and stable chelates with positively charged Ca2+ and Ca(OH)+ species preventing their adsorption on the magnesite surface. Adsorption measurements prove the addition of EDTA can decrease the adsorption of depressant SHMP on the magnesite surface. X-ray photoelectron spectroscopy (XPS) measurements further confirm the transformation from the surface of magnesite to dolomite in the presence of calcium ions, and the possible adsorption mechanism of EDTA and SHMP on the magnesite and dolomite surface. Key words: Magnesite; Dolomite; Surface dissolution; Flotation separation

Jan 1, 2020

By A. Tosun

Muckpile fragmentation formed by blasting depends on the specific charge factor, the discontinuities in the rock mass, and the rock strength. Determination of the discontinuity characteristics and rock strength is a long and difficult process. These two parameters are directly associated with the rock drilling speed. Therefore, it is the drilling speed of the machine used for the blast-hole, rather than the blasthole discontinuity characteristics and rock strength parameters, that is used in the prediction of muckpile fragmentation before blasting. Primarily, it has been suggested that the muckpile fragmentation values can be correctly determined by establishing correlations between the efficiency of the loader and muck pile fragmentation, since fragmentation is directly correlated with the former parameter. Subsequently, a correlation predicting the drilling speed of the drill machine was developed according to the discontinuity characteristics of the blasting surface and the rock strength. Finally, a correlation was developed predicting muckpile fragmentation according to the specific charge factor and the drilling speed of the drill machine The data was obtained by conducting blasting tests in two different limestone quarries.

Nov 30, 2022

By T. Nesane, S. S. Mnyakeni-Moleele, L. C. Murulana

The effectiveness of two synthesized ionic liquids, 1-(benzyloxy)-1-oxopropan-2-aminium 4-methylbenzenesulfonate (1-BOPAMS) and 4-(benzyloxy)-4-oxobutan-1-aminium 4-methylbenzenesulfonate (4-BOBAMS), were evaluated for mild steel corrosion inhibition in 1.0 M hydro-chloric acid solution, using electrochemical impedance spectroscopy (EIS), potentiodynamic polarization (PDP), and gravimetric techniques. Organic moieties responsible for the adsorption process on mild steel surface were investigated using Fourier transform infrared spectroscopy (FTIR). Gravimetric analysis revealed that the inhibition efficiency of 1-BOPAMS and 4-BOBAMS increased with concentration, with maximum inhibition values of 90.32% and 97.91%, respectively, at the highest concentration of the inhibitors. Gibbs free energy (ΔG°ads) values indicated a strong interaction between the mild steel surface and the molecules of the ionic liquids, and that the adsorption process was spontaneous. These values also show that the inhibitive nature of ionic liquids against mild steel corrosion is caused by a mixedtype of adsorption film formed on the steel surface. The Langmuir adsorption isotherm was used to describe the adsorption of ionic liquid molecules onto the mild steel surface. Polarization curves showed that 1-BOPAMS and 4-BOBAMS have a similar effect on both the anodic and cathodic half-reactions, indicating that they prevent the dissolution of mild steel through both physical and chemical process. Nyquist plots were defined by incomplete semicircle capacitive loops, showing that the charge transfer mechanism controls the corrosion of mild steel in acidic solution.

Apr 1, 2021

1. New books Extractionmetallurgy'81. London, Institution of Mining and Metallurgy, 1981. 441 pp. $40. Structures and properties of engineering alloys, by W. F. Smith. London, McGraw-Hill, 1981. 512 pp. R89,65. Rock and mineral analysis, by W. M. Johnson and J. A. Maxwell (editors). 2nd ed. New York, Wiley, 1981. 424 pp. $40. Mining methods and equipment, by Mining Information Services. London, McGraw-Hill, 1981. 218 pp. International directory of acronyms in library, information and computer sciences, by P. M. Vaillancourt. New York, Bowker Publishing Co., 1980.516 pp. 2. New journals Trends in analytical chemistry (TRAC), Amsterdam, Elsevier, 12 issues per year. Subs. for Volume I (16 issues) D.H 95.50. Engineering management international, Amsterdam, Elsevier, 4 issues per year. V.S. $32.50, D.H. 70.00. 3. Mineral policy sector publications Mineral Bulletin MR 188. Vanadium: an imported mineral commodity. $3.60. Mineral Bulletin MR 190. Canadian mines: 1980 perspective. $3.00. Canadian mineral survey 1980, by the staff of Mineral Policy and Energy Sectors. $1.00. 4. NIM reports Report 2090 Observations made during the dig-out of a 48 MV A ferrochromium furnace. Report 2110 The investigation of a fracture on one side of a skip bridle in a mine shaft. Report 2111 Pilot-plant tests for the recovery of chromite and the noble metals from the UG-2 Reef at Maandagshoek. Report 2112 The behaviour of UG-2 chromite concentrates during smeUing. Report 2113 M uUivariable control of a milling circuit at East Driefontein Gold Mine. Report 2115 Estimation of material variation in powdered materials Report 2116 Optimum operation of a direct-reading spectrometer with excitation by a 5 kW inductively coupled plasma torch. Report 2121 Five robust indicators of central value. Report 2124 The direct determination, by differential pulse anodicstripping voUammetry at the thin mercury-film electrode,of cadmium, lead, and copper. Report 2127 The preparation of a reference material of South African zirconium concentrate from Richards Bay. Report 2128 The determination, by differential pulse anodic-stripping voltammetry at the thin mercury-film electrode, of cadmium and thallium in six NIMROC reference materials Report 2130 The organizing of conferences. Research grant The Board of Directors of International Precious Metals Institute in conjunction with Gemini Industries, Inc., a California-based refiner of precious metals, recently announced a Gemini Research Grant of $3000 will be awarded annually to a graduate student who is pursuing studies in metallurgy, chemical processes as it pertains to precious metals, or materials sciences, and who is performing or planning research studies in the precious metals. Accidents and diseases The Third International Colloquium for the Prevention of Occupational Accidents and Diseases in the Iron and Metal Industry is to be held on 15th and 16th June, 1982, in Palma de Mallorca, Spain.

Jan 1, 1981

By S. Stuurman

Inorganic acids such as sulphuric acid have found use together with certain reducing agents in leaching of copper-cobalt oxide ores. These reagents are not ideal due to the adverse effect the inorganic acids generally have on the environment and the high costs of the reducing agents. In this study a copper-cobalt oxide ore from the Central African Copperbelt was leached in two different environments; sulphuric acid in conjunction with hydrogen peroxide as a reducing agent and tartaric acid. The effects of acid concentration, reducing agent concentration, and temperature were independently determined for both leaching environments. The sulphuric acid concentration was varied between 0.4 M and 1.2 M and the concentration of hydrogen peroxide between 4.0 M and 6.5 M, while the tartaric acid concentration was varied between 0.15 M and 0.35 M. The temperature was varied between 20°C and 50°C. The results showed that the extraction of both copper and cobalt increased with sulphuric acid concentration, reaching a peak at approximately 0.8 M and then decreasing at higher acid concentrations. A similar increase and decrease in metal extraction was observed when the reducing agent was increased. In leaching with tartaric acid, the extraction of cobalt was much higher than that of copper, although extraction of both metals increased with acid concentration. Additions of small amounts of hydrogen peroxide were found to increase cobalt extraction in tartaric acid but had a minimal effect on copper. An increase in the solution temperature had a significant effect in the organic acid environment, with the effect on cobalt extraction being much more pronounced than on copper.

Jan 1, 2014

By M. Shaw, H. R. Heydenrych, A. E. Lewis, E. Glass, J. Chivavava

The removal of calcium from the retentates of reverse osmosis (RO) treated minewater is desirable since it allows the recovery of both additional potable water (through RO) and higher-purity salts (in downstream processing). This, in turn, reduces the need for costly and unsustainable evaporation ponds and enhances the economics and operability of potential zero-liquid discharge downstream processes, e.g. evaporative-, cooling- and eutectic freeze-crystallisation. For this study, a multi-component retentate high in sodium content was considered, typical of those emanating from minewater reclamation plants in Mpumalanga, South Africa. Four technologies were evaluated to remove calcium: gypsum precipitation by addition of lime; calcium carbonate precipitation by addition of soda-ash; heating crystallisation of calcium sulphate anhydrite; and cooling crystallisation of gypsum. Full processes were developed and simulated using electrolyte thermodynamics. Using the results of these simulations, capital- and operating costs, as well as revenues were calculated and used in economic comparisons of the processes. Sensitivities to key purchasing and selling prices were also investigated to understand the impact of changes in these variables. For the case of a low magnesium-to-sodium ratio in the feed, gypsum precipitation through lime addition was found to have the lowest operating and total annualised costs; but, if revenue could be derived from the sale of sodium sulphate, calcium carbonate precipitation through soda-ash addition was favoured. Keywords: Calcium removal, gypsum precipitation, calcium carbonate precipitation, heating crystallsation, cooling crystallisation, economic comparison

Jan 1, 2020

By R. o. Cretier, L. A. Cisternas, A. López-Valdivieso, F. Valdes, E. Gálvez, G. Gahona

The size of the particle plays an important role in the flotation of minerals. Comminution allows the release of valuable species and their subsequent recovery. Then, the degree of concentration and recovery will depend on the size of the particle. In this work, we investigated the flotation of coarse particles (-850 +150 μm) of copper ores when using the fluidized-bed separator (HydroFloat® cell) and compared it with the process of conventional flotation with medium size particle (-150 μm) (Metso cell) using seawater. The collector concentration was the main variable studied in terms of copper recovery. The results show that the flotation of coarse particles is feasible using seawater without frother

Jan 1, 2020

By G. Song, X. Liu

The global coal industry has changed significantly in recent years. In this paper we analyse the coal production and consumption, imports and exports, and coal prices in China and other major coal-producing countries during the past four decades. The analysis shows that global coal production and consumption have declined over the last three years, in striking contrast to the continuous growth for most of the past 35 years. Australia, Indonesia, and Russia have become the world’s major coal providers, while China, India, and the USA, and Germany are the major coal consumers. The world’s, and China‘s, coal industry can be classified into four stages of development: the stable growth phase, stable phase, rapid growth phase, and high-quality phase. Coal prices rose in the world’s four major coal markets in 2016 after four consecutive years of falling prices. The elimination of overcapacity and production-optimizing operations in China could assist in achieving a demand and supply balance.

Aug 8, 2024

By D. F. Malan, J. C. Esterhuyse

In this study we explore the use of a novel numerical modelling approach to study the effect of pillar reinforcement on pillar stability. Case studies in the literature indicate that tendons, strapping of the pillars, and shotcrete or thin spray-on liners are commonly used to reinforce pillars. No clear methodology exists to select the type of support or to design the capacity of the support required, however. This has led to ongoing collapses in some mines in spite of heavy support being used to reinforce unstable pillars. A limit equilibrium model with confinement on the edge of the pillar was used to simulate the interaction of the support with the failing pillar. The model correctly predicts that an increase in confinement will lead to a decrease in the extent of pillar failure. As the displacement discontinuity boundary element method allows for the efficient solution of largescale bord-and-pillar layouts, the effect of pillar confinement can now be studied on a mine-wide scale. Accurate calibration of the limit equilibrium model is, however, required before this method can be used for the design of effective pillar support.

May 3, 2023

By A. McQuillan, N. Bar

Geotechnical engineers are routinely tasked with advising suitable stand-off distances below highrisk sections of slopes in open-pit mines that are identified to have potential to deform or collapse. Accurate prediction of failed material runout can mean the difference between continuous safe mining and unwanted high-potential incidents that result in loss of production, equipment damage, injury, or loss of life. This paper updates previous empirical relationships presented by the authors for estimating the volume and runout distance of excavated slope failures, in an open-pit mine operation, using slope geometry as the primary predictor. Cases are sourced from varying slope geometries (fall heights up to 385 m, slope angles up to 80°) and a range of commodities (iron ore, coal, nickel, gold, copper, boron, and limestone), excavated in sedimentary, banded-sedimentary, epithermal, and copper-porphyry deposits, across all six inhabited continents. Analysis of these cases identified positive correlations between slope height and runout distance, and slope height and failed material volume. In general, negative correlations were identified between Fahrböschung angle and slope height, and Fahrböschung angle and failed material volume; however, significant scatter is observed in these datasets. A definitive relationship could not be derived comparing Fahrböschung angle with failed material runout. Slope angle was also found to be a poor indicator of runout. Of the parameters analysed, slope height (i.e., fall height) was found to be the simplest and best predictor of runout distance. This paper presents new charts for predicting failed material runout distance for rock slopes. Relationships are defined for structurally and rock-mass driven slope failure mechanisms at average, 75%, and 95% prediction intervals

Jul 10, 2024

By K. H. Zhang, Y. P. Gao, J. Q. Zhao, Q. Li, J. C. Ma

Compared with sinusoidal oscillation, non-sinusoidal oscillation enhances the ability to control waveform and meets different oscillation requirements by adding an independent parameter, which is the key technology for high-efficiency continuous casting. A new waveform of mould non-sinusoidal oscillation is proposed in this paper, that is, a velocity waveform that is composed only of straight lines and parabolas, which not only has good dynamic characteristics, but also further enhances the feature of non-sinusoidal oscillation. Compared with sinusoidal oscillation, the negative strip time is reduced by 15.9%, the maximum negative strip velocity difference is increased by 38.3%, and the maximum positive strip velocity difference is decreased by 27.8%. The formulas of oscillation process parameters can be clearly deduced, and the isoplethic curves of oscillation process parameters when multi-parameter simultaneously changes are drawn. The negative strip time decreases as the modification ratio, frequency, and casting speed increase, but increases as stroke increases. In order to maintain the stability of negative strip time, an oscillation synchronous control model for optimising oscillation basic parameters was developed. Through practical application, the mean oscillation mark depths decreased by 10.1 μm and the flux consumption is increased from 0.37 kg/t to 0.45 kg/t in the non-sinusoidal oscillation model, which meets the requirements of normal production.

Oct 24, 2025

By J. Gilliland

The Grootegeluk coal-beneficiation plant was erected in the Waterberg coalfield, near Ellisras in the Transvaal, to supply Iscor's steelworks with a predetermined tonnage of coking coal in accordance with strict quality requirements. This plant has to handle a high tonnage of raw coal, which is not easy to beneficiate, in order to produce 1,82 X IQ6t of coal. Extensive tests were conducted on borehole cores and a mass sample of coal obtained from the area. These tests were carried out on a laboratory and pilot-plant scale, and were aimed at the establishment of the most effective beneficiation methods and the choice of suitable equipment. This led to the completion of a full set of design and manufacturing drawings that resulted in the project approach . described in this paper.

Jan 1, 1982