Search Documents

By E. Chen, M. Barati, K. Coley

The reaction between carbon and slags is of significant importance in direct smelting of iron ores, EAF slag foaming and copper slag cleaning processes. This reaction is known to occur via gaseous intermediates and it is important to have fundamental data to understand the relative importance of each reaction step. In this study, the rate of CO2dissociation on different slag surfaces is measured using an isotope exchange technique. It was found that increasing iron oxide content up to 30 wt per cent does not have a significant effect on the rate constant while increasing from this limit, increases the rate constant dramatically. Activation energy of CO2dissociation on slags of unit basicity and different iron oxide contents is in the range of 180±40 kJ/mol. It is found that rate constant dependence on oxygen potential in the slag phase is increasing with iron oxide concentration. In the case of copper making slags, the influence of copper oxide is found to increase the magnitude of apparent rate constant, while decreasing the activation energy considerably. Key words: Gas-slag reaction, CO2dissociation, copper slag, kinetics, isotope exchange

Jan 1, 2004

By R. Altindag

In rock cutting mechanics, the effects of the rock and coal brittleness on the efficiency of cutting bits are examined by many researchers. There is no universally accepted brittleness concept as a measure of cutting efficiency. The effect of the brittleness on rock cutting has not been completely explained. The aim of this study is to correlate the relationships between Specific Energy (SE) and brittleness concepts. The applicability of various brittleness measurement methods for rock cutting efficiency has been investigated. In this study, the raw data derived from previous experimental studies were used, and the relationships between SE and brittleness concepts were investigated. The two previously used brittleness concepts, which are named as B1 (the ratio of compressive strength to tensile strength) and B2 (the ratio of compressive strength minus tensile strength to compressive strength plus tensile strength), and a new introduced brittleness concept named B3 (the area under line in relation to compressive strength and tensile strength) were evaluated in this study. The relations among these brittleness concepts for rock cutting efficiency were established using regression analysis. There is no correlation found between the SE values and the brittleness of B1and B2values. But, the SE is strongly correlated with the brittleness of B3. It was seen that the suggested brittleness of B3concept could be used as an indicator in rock cutting efficiency analysis.

Jan 1, 2003

By S. V. Rungan

Since 1994, South Africa has been the subject of international attention, especially in regard to its transformation initiatives, which aim to redress the post-apartheid imbalances. Mining, as a major employer and one of the major industries in South Africa, has been the focus of the government?s Black Economic Empowerment initiative with the introduction of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The historical background to South Africa?s transformation and the role of the mining industry are pivotal to an appreciation of certain aspects of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The issues around Black Economic Empowerment and the enabling of a smooth transition to the South African mining industry of the future are explored in this paper.

Jan 1, 2005

By X. Yu

Although many investigations of the deformation behaviour of rocks have been carried out, most of them are carried out in compression. In all rock engineering practice it is usually assumed that the deformation of rocks in tension is the same as that in compression. However, data from numerous researchers have shown that this assumption is not correct for some rocks. A new loading frame for testing rocks in compression and direct tension has recently been developed by the authors, with the capacity to conduct both compression and tensile tests on the same rock sample. The results obtained show that the ratios between the average Young?s modulus in compression (ECA) and in direct tension (ETA) are 1, 1.16, 2 and 6 respectively in four rock types tested. For Poisson?s ratios, analogous relations were obtained. It was observed that, in all cases, the tangent Young?s modulus intension reduces with an increase in the applied tensile stress, while the behaviour of Poisson?s ratio is similar, but shows greater variability. The difference between the Young?s modulus of rocks in tension and that in compression could lead, large errors in calculating induced stresses around underground openings, as well as in determining the Brazilian tensile strength of rocks. This may have a significant influence in rock engineering and therefore more investigation is necessary into the tensile deformation behaviour of rocks and its influence.

Jan 1, 2005

By R. Butcher

Mud rushes are hazardous occurrences that have occurred frequently in mines in South Africa, and have been the cause of numerous fatalities in the past. Mud rush incidents not associated with accidents are believed to be common occurrences that are not generally reported. Many such incidents are probably associated with the operation of chutes and box fronts. This paper describes the conditions necessary for mud rush occurrences, postulated mud rush mechanisms, and methods of combating the mud rush hazard.

Jan 1, 2005

By A. Hammel

This paper summarizes indigenous mining methods used to collectmetal ores in pre-colonial southern Africa, south of 15°S. These methods, for the purposes of discussion, are divided into sections inorder of increasing organizational complexity, from scavenging,which only required basic equipment and a relatively minimal division of labour, to underground mines, which necessitated complex planning to overcome obstacles such as the need for illumination and ventilation. Examples concerning the pre-colonial exploitation of iron, copper, tin, and gold have been taken from the archaeological literature. This review paper provides an introduction to the technology that was available to and used by miners in the past, illuminates some of the factors limiting their operations, and supports the claim to the indigenous nature of this activity

Jan 1, 2000

By K. Cybulski

In 2002 a coal dust explosions occurred in the Polish collieries “Jas-Mos” and “Rydultowy” in the Upper Silesia coal basin. In the “Jas-Mos” colliery the coal dust explosion was initiated in the face of gallery by explosives and causing ten death. The stone dust barrier extinguished the flame, stopped the explosion development and saved forty nine miners working in that area. In the “Rydultowy” colliery methane inflammation caused three deaths and seven serious burns and ignited the coal dust explosion. The coal dust explosion was stopped by stone dust barrier and did not cause any victims itself. This paper presents the investigation carried out by the Central Mining Institute Experimental Mine “Barbara” and shows that the stone dust barriers remain still a basic mean for suppression of coal dust explosion in mines. The investigation were aimed at determining the cause of explosion and circumstances that led to their propagation. The evaluation of the state of dust explosion hazard in the areas of accidents have been performed, and the range of flame estimated.

Jan 1, 2003

Council for 1999/2000 President J.R. Dixon President Elect M.H. Rogers Vice Presidents Senior Dr L.A. Cramer Junior A.A.B. Douglas Immediate Past President R.P. Mohring Honorary Treasurer J.A. Cruise Members of Council B.C. Alberts Dr N.A. Barcza N.J. Barkhuysen R.D. Beck M.J.P. Bierman Prof. A.N. Brown D. Cockcroft Dr M.B. Cortie Dr L.A. Cramer J.A. Cruise E.G. de Villiers J.R. Dixon A.A.B. Douglas F.M.G. Egerton J.P.W. Fisher C.E. Fivaz K.J.R. Ford Prof. G.A. Fourie R. Graham Dr R.G. Gürtunca Dr R.V.R. Handfield-Jones* M.C. Harris J.P. Hoffman H.E. James P.J. Knottenbelt R.P. Mohring H.G. Mosenthal G.Y. Nisbet N.M. O'Brien R.G.B. Pickering Prof. R.P. Plewman S.J. Ramokgopa Prof. R.E. Robinson M.H. Rogers D.A.J. Ross-Watt Prof. R.F. Sandenbergh Dr H. Scott-Russell C.B. Sheppard D.A.A. Smith Dr T.R. Stacey Dr O.K.H. Steffen D.J. van Niekerk J.C. Viljoen J.N. Wallington

Jan 1, 1999

Experimental studies on viscosity of titanium bearing slags have been reviewed and the assessed data were used in extending the capability of the structurally related viscosity model for silicate melts, developed by the present authors. Experimental data on ternary and higher order systems containing CaO, MgO, MnO, FeO, Al2O3, TiO2, Ti2O3, SiO2were assessed and used. The newly extended viscosity model represented the viscosity behaviour over broad temperature and composition ranges. The structural role played by TiO2and Ti2O3in silicate network structure is discussed with respect to their effect on viscosity of melts. Keywords: viscosity model, TiOx containing silicate melts, silicate network structure.

Jan 1, 2004

By G-L. Wu, S-W. Wu

"The hot deformation behaviour of Nb-Ti microalloyed high-strength steel was investigated. Hot compression tests were conducted in the temperature range 900 to 1100°C under strain rates of 0.1, 1, and 5 s-1. Dynamic recrystallization (DRX) occurs as the main flow softening mechanism at high temperature and low strain rate. The hot deformation activation energy was calculated to be about 404 699 J/mol. The constitutive equation was developed to describe the relationship between peak stress, strain rate, and deformation temperature. The characteristics of DRX at different deformation conditions were extracted from the stressstrain curves using the work hardening parameter. The Cingara-McQueen equation was developed to predict the flow curves up to the peak strain. The processing maps were obtained on the basis of a dynamic materials model. The results predict an instability region in the temperature range 1010 to 1100°C when the strain rate exceeds 0.78 s-1. IntroductionThe 700 MPa grade HSLA steel is widely used in engineering machinery, automotive beams, carriages, and axle tubes, etc. (Pan et al., 2017 ). Generally, such grades contain a moderately high amount of Mn (approx. 1.4% and above), and microalloying elements like Nb, Ti, V, and Mo to impart the desired strength and toughness through solid-solution strengthening, precipitation hardening, and grain refinement dislocation strengthening (Chen and Yu, 2012; Opiela, 2014). However, the production costs can be greatly reduced by replacing part of the Nb, V, or Mo with inexpensive Ti and adopting the compact strip production CSP process (Opiela, 2014; Chen et al., 2015). Furthermore, the microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient for achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Wu, Zhou, and Liu, 2017).In hot forming processes, the complex microstructural evolutions are often induced by multiplicative hot deformation mechanisms, such as work hardening (WH), dynamic recovery (DRV), and dynamic recrystallization (DRX) (Zhang et al., 2014; Liang et al., 2015). Dynamic softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by its corresponding microstructural evolution (Wu et al., 2010). During deformation in the DRX process, deformed grains are replaced with substructures and newly formed fine and uniformly distributed grains. This occurs only when a critical strain for the onset of DRX is reached, and at the same time, the minimum rate of energy dissipating is reached (Ferdowsi et al., 2014). DRV occurs at a high strain rate and low temperature, reducing the stored energy greatly and making DRX difficult (Liang et al., 2015). The microstructural changes during DRX are sensitive to the processing parameters, such as strain rate, deformation temperature, and strain (Zhang et al., 2014; Ferdowsi et al., 2014). Therefore, in order to optimize the hot processing parameters, it is important to understand the behaviour of hot deformation visà- vis control of microstructural evolution."

May 1, 2019

Council for 2003/2004 President T.R. Stacey President-elect F. M. G. Egerton Vice-presidents Senior W. H. van Niekerk Junior R.P.H. Willis Immediate Past-president S.J. Ramokgopa Honorary Treasurer J.A. Cruise

Jan 1, 2004

By J. P. Theron

Paper written on project work carried out in partial fulfilment of Phd.(Process Engineering) degree Process modelling is an essential element in the development of advanced (model-based) process control systems, accounting for up to 80% of the cost of development. Often, models based on historic process data are the only viable option when dealing with processes that cannot be modeled cost-effectively from first principles. Despite major advances that have recently been made in the field of nonlinear process modeling, some basic idea of the dynamic behaviour of a process system is important prior to system identification. While many process systems seem unlikely to be linear, the possible nonlinear aspects of their dynamics are not necessarily supported by the data. This may have significant implications for subsequent system identification or interpretation of the data. For example, it is quite possible that an underlying nonlinear deterministic signal may be obscured by a high degree of measurement or process noise, to the extent that it may be critical in the choice of model to fit to the data. The method of surrogate data analysis has recently been proposed as a means to classify the underlying dynamics of complex systems, and in this paper the use of Fourier transform surrogates to classify process systems is explored. Keywords: modelling, process control, simulation, surrogate data analysis, nonlinear systems.

Jan 1, 2004

By F. Sawyerr

A bubble population balance model is proposed for the prediction of Sauter mean bubble diameters in mechanical flotation cells. In the model, the flotation cell is treated as two separate, statistically homogeneous zones?the impeller zone, and the bulk tank zone. Balance functions for the rates of bubble breakage, coalescence, recirculation and inlet-outlet events are proposed based on classical chemical engineering research in two- and three-phase fluid mixing systems. An initial simulation of the population balance model shows trends in bubble size distributions comparable to measured distributions in industrial mechanical flotation cells.

Jan 1, 1998

By M. Suzuki, T. Shiomi, M. Nakada, K. Tsutsumi

Mold powder plays an important role in the continuous casting process for high quality steel production. It is well known that mold powder entrapment causes surface defects in steel sheet and the high viscosity of mold powder prevents the entrapment of mold powder in molten steel in ultra low carbon steel. This paper deals with the entrapment of mold powder caused by suction by Karman?s vortex in a laboratory experiment. At first the effect of the viscosity of oil and interfacial tension between water and oil was investigated in a water model experiment. Then hot model experiments were carried out by mold powder and molten steel. The amount of mold powder entrapment was affected by the viscosity and the interfacial tension between molten steel and mold powder. As a result, the following equation of the mold powder entrapment was obtained. m=1.06*107?-0.255?m-s-2.18 The amount of mold powder entrapment decreased when the viscosity and interfacial tension increased. But the effect of viscosity was larger than that of interfacial tension in the case of the industrial mold powder when the viscosity was under 0.5 Pa.s, interfacial tension was from 1200to 1300 mN/m.

Jan 1, 2004

By B. Samanta

A quality characteristic analysed through construction of the Shewhart control chart is required to be normally distributed. In mining applications, this assumption is often violated as many quality characteristics follow skewed or lognormal distribution. In this paper, two methods were investigated using a heuristic approach for setting up the control limits for a skewed population. Based on these approaches a Mode chart, and a Weighted Variance (WV) control charts were constructed. The performance of the proposed methods was compared with the normal based Shewhart method through a case study conducted in a surface mine supplying iron ore to a steel plant. A simulation study was also conducted to evaluate the effectiveness of the proposed methods over the Shewhart method. The study revealed that the Shewhart control charts generated more out of control alarms compared with the Mode and Weighted Variance control charts for a skewed population of Fe%. The simulation results also revealed that for extremely high skewed population, the WV control chart and Mode control chart provided higher probability of coverage than the Shewhart method; although the detection rate (probability of detection) of out of control condition for these methods was slightly reduced compared with Shewhart method.

Jan 1, 2004

By P. K. Sahoo, C. R. Ray, S. S. Rao

This paper deals with various factors affecting the strength of chromite briquettes which plays a vital role in the smelting of charge chrome / ferro chrome production. Appropriate briquetting parameters like molasses and lime binder level, molasses quality, particle size distribution and segment condition etc. are essential to guarantee quality briquettes in the successful use of briquette and chromite ore fines. In developing a technology for briquetting of chromite ores, it is important not only to study the grain size characteristics of the chrome ore fines but also to make an informed choice of the type and quality of the binder and the condition for producing a physically and chemically competent green and cured briquette. This paper also describes the effect of strength of briquettes on various parameters of charge chrome production as the use of quality briquettes in the production of high carbon ferrochrome alloys has a number of operational, metallurgical and economic advantages. It is also a requirement for submerged arc furnace operation that the charge be adequately porous to allow gaseous products of the reduction reaction to escape from the furnace charge burden without hindrance. Otherwise, furnace material would erupt causing electrodes and furnace other equipments damage and risking the safety of the work force. The briquette, because it replaces lumpy charge but has an advantage of smaller size, allows for an uniform and porous charge so that the ascending gaseous products can escape freely. Finally this paper deals with furnace operational results with varying proportion of briquettes having same strength.

Jan 1, 2007

By D. François-Bongarçon

When it comes to sampling theory, a bad sampler is a bad sampler, no matter what, and a sampler is either bad or good. It also is of critical economic importance to tell and understand the difference, especially in a metallurgical plant. In this paper, the grand principles of Sampling Theory are first recalled, then the most popular types of sample cutters for plants are critically reviewed. It is concluded that the industry has a lot of progresses to make in that direction, although improvements usually pay for themselves very quickly.

Jan 1, 2002

In recent years several mine researchers have studied the optimization of cutoff grade with the purpose of maximizing Net Present Value (NPV). The best and most popular one is the Lane algorithm. Based upon the Lane algorithm it is possible to calculate the optimum cutoff grade for mine, mill, and refinery capacities for single metal deposits with variable grades. The Lane algorithm cannot be used in multiple metal deposits. The reason is that, while in single metal deposits six points are possible candidates for the optimum cutoff grade, in multiple metal deposits an infinite number points are possible candidates for the optimum cutoff grades and objective function evaluation of these infinite points is impossible. In this study the Golden Section search method was used to calculate optimum cutoff grades of multiple metal deposits for the same conditions as Lane assumed in single metal deposits. Based on this method, grade-tonnage distribution uncertainty space of problem is guessed. In the next step, by selecting test points in uncertainty space and evaluating the objective function at these points, a part of uncertainty space will be eliminated. The procedure is then repeated until the uncertainty space has been sufficiently reduced to ensure that the optimum cutoff grades have been located to the required accuracy. Key words: Optimum cutoff grades, Optimization, Net Present Value (NPV), Golden Section search method

Jan 1, 2003

By M. Le Roux

Fine coal (-500 µm) is notoriously difficult to dewater. It is not uncommon for a dewatered product to have a moisture content as high as 30 per cent after vacuum filtration. This poses several handling and financial problems to such an extent that a lot of fine coal is discarded onto slurry waste ponds. A novel way of dewatering fine coal was developed at North-West University. It entails deliberately damaging the filter cake during dewatering to allow for an increased flow of air through the cake at the expense of the applied pressure differential. This method resulted in an average improvement in final cake moisture of between 3 per cent and 5 percent when executed in the laboratory under controlled conditions. A device was designed that could be fitted onto existing belt filters that would damage the filter cake as it passes by. This device was tested on a vacuum belt filter installation at a coal beneficiation operation in the Waterberg coal field in South Africa. The results showed a 3 per cent reduction in final moisture of the cake, proving the validity of the method at full industrial scale.

Jan 1, 2012

By H. J. Ilgner

The paper reviews the results to date of an integrated research programme currently being conducted by CSIR Mining Technology, aimed at impacting significantly on concentrated mining with face advance rates of up to 20 times faster than presently achieved. Consideration is given to the interplay between innovative technologies for continuous non-explosive mining or rock comminution underground and lateral hydraulic transportation in cross cuts, haulages and eventually hydro hoisting. Novel technologies for underground comminution of reef and development waste and an innovative pumping system suitable for the hydraulic transportation of coarse comminuted rock are reviewed. Emphasis is placed on South African gold mine reef and waste samples comminuted by electric shock wave comminution technology. The innovative TORE® pump system appears to be well suited for the successful hydraulic transportation of rock, produced by electric shock wave comminution, at solids concentrations between 45 % and 67 % by mass.

Jan 1, 1997