Search Documents

By Thomas J. Peters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 17,320-acre portion of the 52,143-acre Little High Rock Canyon Wilderness Study Area (CA-020-913/NV-020-008) in order to evaluate its identified mineral resources. The study area is located in Humboldt and Washoe Counties, NV, about 42 miles north from Gerlach. Three areas of epithermal alteration, similar to alteration associated with disseminated gold deposits, were found in the study area. One of the areas occurs along a northeast-trending structural lineament. Southwest of the study area two gold prospects undergoing active exploration, as well JS a gold deposit being prepared for production, occur along the same lineament. The Bureau of Mines examination, however, did not find evidence for gold resources in the study area.

Jan 1, 1987

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the quantitative procedures that have been developed for the mine-specific analyses of accident/injury experience data are presented and their applications are demonstrated in a summary form through case study examples. The quantitative procedures will aid mine safety management personnel to develop focused accident prevention strategies including training, as well as to justify the investment in such proactive programs through cost-benefit analyses.

Jan 1, 1993

By W. H. Tomlinson

The fourteenth National First-Aid and Mine Rescue Contest we;; held at the State fairgrounds, Columbus, Ohio, October 2, 3, and 4, 1951. The meet, the first such event in 21 years, was under the auspices of the Bureau of Mines, United States Department of the Interior, and the Joseph A Holmes Safety Association and was sponsored by the National Coal Association, the United Mine Workers of America, and various State mine-inspection departments. The cooperating agencies that contributed to make the meet a success, in addition to the National Coal Association and the United Mine Workers of America, were the Kentucky Department of Mines and Minerals, Ohio Division of Mines, West Virginia Department of Mines, Pennsylvania Department of Mines, and the Columbus Convention Bureau. SUMMARY Fourteen teams from 6 States participated in the mine rescue contest, and 55 teams from 9 States competed in the first-aid contest. Only one of these teams entered as a combination team, that is, participating in both the mine rescue and first-aid contests. The States represented and the number of teams from each State are listed in table 1.

Jan 1, 1953

By David L. Shuck

This report was prepared for the Bureau of Mines to describe the current methods of design, construction, and development of wells for in situ leaching of uranium. The discussion includes the alternatives for well design drilling equipment and fluids, grout formulation and emplacement, well integrity testing and repair, and well development and stimulation. Current practice in these areas was determined through interviews with eight operators of commercial scale in situ facilities and is also discussed. Based on this information plus the authors' experience, recommendations are made regarding well design, construction, and development tor in situ leaching.

Jan 1, 1982

By G. C. Lammers

The object of this study was to determine the economic feasibility of hydraulically transporting Sandow (Tex.) lignite 100 miles and dewatering and thermally drying the transported lignite to a surface-dry condition. The most important factors involved in the feasibility of hydraulic transport, are the degradation incurred during transit, the length of the line, and the cost of alternative methods of shipment. In pipeline tests in which roughly 75 miles of hydraulic transport was simulated the percentage of minus-325-mesh solids increased from about 1 to 41 percent for both lignite and bituminous coal; in the micron sizes the coal fared considerably better than the lignite. Such degradation, even though it enhances flow through the pipe-line, severely aggravates the dewatering problem on lignite. Cost studies indicated that continuous vacuum filters offer the most economical means of dewatering minus-1/8-inch material. Surface moisture, if high, must be removed by relatively expensive thermal drying.

Jan 1, 1958

By D. Harry Chambers

The Bureau of Mines, through a memorandum of agreement with the Department of Defense, conducted research to recover silver from aircraft scrap. Silver was recovered by an electrolytic method from stainless steel honeycomb sections separated from the aircraft. These sections had been constructed by sandwiching a stainless steel honeycomb core between stainless steel sheets and then brazing the assembly with a silver alloy. Over 300 pounds of silver was used in the B-58 bomber, concentrated in certain honeycomb sections of the aircraft. Following shredding of the aircraft parts, an average of 95 percent (ranging 67 to 100 percent) of the silver was recovered in a single electro-refining step. After the electrorefined product was magnetically cleaned, purity of the recovered silver was greater than 99.3 percent.

Jan 1, 1980

By R. Pallini

The Franklin Research Center (FRO, a Division of The Franklin Institute was contracted by the U.S. Department of Energy to investigate the application of elastomeric materials for the purpose of smoothing loads on dragline thrust rollers. This report covers the design, fabrication, and demonstration of a portable- device for measuring roller circle track deviations and roller loadings. The results of this work are documented in this report. During December 1981, a field test group visited the Falkirk Mine, Underwood, North Dakota for the purpose of demonstrating the use of the designed and built device. The data collected indicates the practicality and usefulness of such a device for determining actual dragline roller circle roller loads, while the dragline is in service. The device was useful in determining roller load peaking that may be a contributing Factor in the premature failure of these thrust rollers. The device could be used for field evaluation of elastomeric cushioning materials used to eliminate these load peaks.

Jan 1, 1982

By Charles F. Jackson

Gold mining is a subject that not only appeals to the popular imagination but has vital importance to the world's economic structure. However, a discussion of the use of gold as a medium of exchange, and a basis for credit between nations and for monetary systems is not within the scope of this paper. The importance of gold in carrying on the commerce of the world, the present supply and rate of production, the probable trend of future production, the probable future requirements, and related subjects have recently received much attention from bankers and economists, and many articles on these subjects have been published. During slack periods of base-metal production due to falling prices, accompanied by scaling down of base-metal mining operations and often by the closing down of at least some mines, there usually result revival of interest in gold mining, search for previously undiscovered deposits, and reopening of some old gold mines.

Jan 1, 1932

By R. B. Anderson

SULFUR poisoning of iron catalysts in the Fischer-Tropsch synthesis was investigated at the Bureau of Mines, because synthesis gas produced from coal contains sulfur compounds. Tests of two typical iron catalysts with synthesis gas containing known concentrations of H2S were made to determine catalyst life as a function of sulfur concentration to ascertain the type of gas purification required. Fixed beds of activated steel turnings and a fused iron oxide catalyst were investigated in sulfur poisoning tests at 21.4 atmospheres with IH2+100 gas containing 6.9, 23, or 69 mg S as H2S per cubic meter (0.3, 1.0, and 3.0 gr per 100 cu. ft.). In tests of reduced catalysts at constant temperatures, more than 80 percent of the activity was lost when 0.5 mg S/g Fe was introduced. Poisoning of nitrided or carbided fused iron oxide catalysts to a given extent required more than twice as much sulfur than for the corresponding reduced catalyst. When the synthesis temperature was increased to compensate for loss in activity, tests of the fused iron oxide catalysts at constant productivity could be continued for 19 to 98 days. The tests were terminated by clogging of the reactor, presumably caused by carbon deposition. One objective of the present work was to determine if synthesis gas, purified by the Bureau of Mines' hot-potassium carbonate process for removing H2S, OOS, and CO2, is suitable for synthesis on iron catalysts. The sulfur content of the gas purified by tills process is in the range of concentrations used in the present work. In constant-productivity tests of nitrided fused iron oxide catalysts with synthesis gas containing 6.9 mg S/m3, catalyst lives are nearly long enough for serious consideration of tills mode of operation. However, factors relating to selectivity and stability of the catalyst indicate that this type of operation is impractical for a commercial process. On this basis additional gas purification, such as iron oxide boxes following a hot potassium carbonate scrubber, is desirable.

Jan 1, 1965

By William A. Beck

The Construction Aggregates Corp. operates a plant for processing sand and gravel from two deposits in Ottawa County, Mich. The bulk of the sand is obtained from a sand dune on the shore of Lake Michigan, and the gravel is dug from a glacial-drift deposit farther inland. Mining is done with draglines, and the material, both at the digging site and in the plant, is moved mainly by systems of conveyors. The Ferrysburg plant serves customers along the Great Lakes, which is unusual for a business normally local in character. Annual production exceeds 1-1/2 million tons of sand and gravel as concrete aggregate and 200,000 tons of core sand for foundry use.

Jan 1, 1962

By Robert M. Baker

This document details the method whereby Allen Corporation of America gathered and analyzed data and developed an annotated bibliography of metal and nonmetal mine fire reports (1950-1979). The primary objective of this program was to develop the annotated bibliography which included MSHA accident reports and periodicals. Two additional objectives were to gather data on non-reportable fires and to conduct statistical analyses on the data to delineate trends. Data was acquired from three major areas: periodicals, MSHA fire reports, and mine safety directors. Data was separated into reportable fires (at least ½ - hour duration or injury), non-reportable fires, and opinion data. The data was then analyzed by time trends, state, ore, ignition source, burning substance, location, equipment, detection, duration, injuries, fatalities, and successful extinguishing agent. The authors make a number of recommendations: (1) improved stationary electrical equipment design and fire protection, (2) improved design of mobile equipment to separate combustibles from ignition sources, (3) improved maintenance, (4) improved housekeeping, and (5) improved training. The document is divided into two volumes and an appendix. Volume I contains data acquisition procedures, data analysis procedures, and conclusions and recommendations. Volume II contains a chronological list of mine fires and fifteen indexes to assist the reader in locating fire incident report of interest. The Appendix contains the annotated bibliography of over 300 metal and nonmetal mine fire reports and journal articles and a list of non-reportable fires.

Jan 1, 1980

By H. A. Doerner

"During the year which has passed since the last progress report on reduction of zinc by natural gas,3 the laboratory experiments on this investigation have been completed. In this concluding report, the whole subject will be reviewed and additional data presented.Chemical ReactionsIn a thermodynamic study of zinc smelting, Maier 4 discussed the use of methane for reducing zinc oxide, and predicted equilibria at various temperatures for the sore important reactions. The study has been extended to include the following list.Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1) at equilibria would be substantially complete at or above 927°C. A subsequent papers described experimental verification of these predictions and gave data on reaction rates under various conditions.It methane is passed through a heated bed of zinc oxide at a low enough rate reactions (1), (3), and (4) reach an equilibrium which can be expressed by reaction (10). The equilibrium concentrations for the products of this reaction in the temperature range 900° to 1100°C. were calculated by applying the thermodynamic constants to the stoichiometric relations. 6 The results of these calculations are listed in table 1 and shown graphically in figures 1, A and B. These data have major importance, and experimental work has shown that they are subtantially correct."

Dec 1, 1934

By Candice Stevens

The Territory of Afars and Issas is to receive its independence from France on June 27, 1977. The Territory's economic income was based on entrepôt trade through the port of Djibouti and trans-shipment of goods on the Chemin de Fer Franco-Ethiopian (CFE) railroad. The Territorial budget was scheduled to in- crease from $32.6 million3 in 1976 to $36 million in 1977, despite severe shortfalls in 1976 stemming from inflation and a persistent balance-of-trade deficit. Subsidies from France continued to sustain the economy, and the French pledged to provide approximately $140 million in aid annually after independence. In 1976, financial agreements were concluded with a number of Arab oil-producing countries, including Saudi Arabia which granted $10 million toward development projects. The new Republic of Djibouti is scheduled to become the 49th member State of the Organization of African Unity (OAU) and the 21st member of the Arab League, and to receive aid from their financial institutions. The port of Djibouti and the CFE railroad constituted the Territory's main economic resources. Traffic at the port greatly

Jan 1, 1980

By Joseph Grumer

An instrumented spherical vessel has been used for many years to study laminar combustion waves. Concurrent measurements of flame speed and pressure-rise rates have led to evaluations of burning velocities, the pressure dependence of the burning velocity, and the expansion ratios of the gases passing through the combustion wave. For the most part, these studies have involved flames initially at atmospheric or subatmospheric pressure. The old spherical vessel used by the Bureau of Mines was not designed for use at elevated pressures. Moreover, being made of wrought iron, it was susceptible enough to corrosion to prohibit its use with many combustible mixtures that figure in industrial research. In mid-1956, under sponsorship of the Office of Naval Research, the Bureau undertook the development of a stainless steel spherical vessel capable of withstanding explosions of gaseous mixtures at initial pressures as high as 20 atm. and initial temperatures as high as 250° C. The design called for a double array (cross) of closely spaced small windows for observation of the flame as it traversed the vessel and a piezoelectric transducer to measure concurrently pressure-rise rates. Because no commercial contractor was willing to bid on the construction of such a vessel, it was built at the Bureau's Bruceton machine shop.7

Jan 1, 1961

By R. A. Friedel

THE IMPORTANCE of infrared and ultraviolet-visible spectrometry in studies of the structure of coal and similar substances is described. Special experimental techniques have been developed for these studies. Thin sections of coal are preferred, but halide pellets are easier to prepare. Information obtained from infrared spectra on chemical functional groups has been discussed; the importance of both intensities and wavelengths of absorption bands has been emphasized. Functional groups assigned include aliphatic and aromatic CH, methylene and methyl groups, hydrogen-bonded hydroxyls, hydrogen-bonded and chelated carbonyls, phenolic structures, minerals, and aromatic structures that are benzenoid or polynuclear. Infrared studies of structures of coal extracts, distillates, and reaction products of various processes, both chemical and physical, are discussed. Coallike infrared spectra of chars of model compounds have been utilized extensively in studies of coal structure. Ultraviolet-visible absorption spectra of coals show a lack of fine structure and low spectral intensities. These results have been applied to the questions of the chemical and physical structure of coal, particularly the question of polynuclear aromaticity of coals. The color of coal is also treated. The physical-chemical origin of the color of coal may be due to free radicals, as interesting correlations of ultraviolet-visible spectra with electron paramagnetic resonance have been obtained. The optical color of coal has been explained and simulation of the color changes observed in thin sections has been carried out, The spectra and structure of coal derivatives and other carbonaceous materials are also discussed. Possible sources of error in absorption spectral measurements are pointed out. Limited measurements of the ultraviolet-visible reflectance spectra of coal are described.

Jan 1, 1967

By F. W. Lee

List of GEOPHYSICAL ABSTRACTS

Jul 1, 1932

By W. M. Deaton

[The formation of gas hydrates in natural-gas pipe lines depends on temperature and pressure conditions in the lines as well as on the presence of condensed water. The operating pressure in a pipe line may be determined easily and usually is available from the records of operation, but the temperature seldom is known. In cooperation with the American Gas Association, the Bureau of Mines, in its investigation of gas hydrates, conducted a pipe-line-temperature survey and studied underground temperatures at depths at which pipe lines ordinarily are buried and the relationship of these temperatures to prevailing atmospheric conditions. A similar but more limited study of this type was, conducted by engineers of the Bureau of Mines a number of years ago.4/A summary of the earlier findings was included in a general report by the Bureau on the flow of natural gas through high-pressure transmission lines.5/ In the present study, data on temperature variations were obtained at several places widely separated geographically. This information should assist pipe-line engineers in designing and operating natural-gas pipe lines. In the pipe-line-temperature survey here resorted, a study was made along a 22-inch natural-gas pipe line: originating near Amarillo, Tex., and extending northwestward through New Mexico into Colorado (fig. 1). Some data also were collected along a 16-inch line extending southward from Amarillo. In the study of underground temperatures and their variation with atmospheric temperature, recording; equipment was installed at the]

Jan 1, 1941

By Joseph Gersic

MINFO has been developed to serve as a frontend for three databases created to store basic minerals information gathered during the minerals resource assessment conducted by U.S. Bureau of Mines(USBM) for the Malheur and Jordan resource areas of southeastern Oregon(MJRA). The primary database is the Minerals Location Inventory (MLI.DBF) which contains of information assembled from field work performed during this project, the USBM Minerals Availability System/Mineral Information Location System(MAS/MILS) database, the Oregon Department of Geology and Mineral lndustries(DOGAMT) Mineral Information Location(MILOC) database, and the U.S. (Geological Survey(USGS) Mineral Resource Database System(MRDS), In addition, assay results are contained in the geochemical database (ELEMENTS.DBF) and modified X-ray diffraction analysis information is contained in the minerals database (MINOR.M.DBF). MINFO includes four types of program modules: ? Enter/Edit Data was developed to allow the addition of new information and to encourage correction of errors by providing a convenient means of entering and editing data and a large degree of automatic checking and filtering of entries. ? ACAD/DBF Link links each site symbol posted on the map in the drawing file to a record in the database. This provides the user with the ability to use a mouse or other pointing device to graphically select a site for viewing and editing. Edits are performed directly in the database file, ? Reports contains 7 formats of data output for creating files for printing, transfer to other database formats, and exporting to other software packages such as spreadsheets and word processing programs. ? Maps includes 5 programs for creating AutoCAD script files which can be used to create maps of selected information in conjunction with AutoCAD. Mineral location mapping files derived from MLI.DBF can be created in 2 formats. Mapping files can be generated from each of the 2 sets of geochemical analyses contained in ELEMENTS.DBF. X-ray diffraction analyses can also be translated into instructions for creating and posting piecharts at sampling sites.

Jan 1, 1994

By Richard F. Hewlett

The purpose of this Bureau of Mines paper is to provide the mineral industry with current information on high-speed data processing and to illustrate how some of these techniques can be applied to the industry. The need for applying these techniques is generally recognized, but not much information is readily available on specific applications. This paper briefly describes high-speed data processing and reduction equipment in an effort to familiarize the reader with the functions of the equipment. A list and explanation of some of the possible applications of high-speed data processing for the mineral industry are included. A few of these applications are illustrated by the use of specific examples of existing computer programs or processing methods, including their calculation times and costs. Some of the programs cited herein were developed by the author at the University of Arizona for a Masters thesis in mining engineering. When a reference is made to a specific computer, the reference is given to make the information that is being presented as factual as possible; most of the manufacturer's equipment that is mentioned in the references was available at the University of Arizona, and no specific endorsement of that manufacturer is intended.

Jan 1, 1962

By James J. Scott

Eleven workshops were held in various locations throughout the country in an attempt to reach the many diverse groups working in various mineral commodity areas and special ties. These meetings were held between March 1, 1974 and June 25, 1975. They were held under the auspices of the Bureau of Mines Contract to the University of Missouri-Rolla which was designed to help define Bureau research and development priorities. At each workshop a summary of current Bureau research and development was presented and the attendees were asked to present their ideas on what Research and Development programs should be undertaken to meet their needs locally. Participants included representatives of federal and state agencies, educational institutions, mining companies, equipment companies and other interested parties. The workshops covered under this report include lead mining in Missouri, limestone mining, coal mining both surface and underground in the midwest and in the Rocky Mountain area, iron mining in Minnesota, two top management meetings on institutional problems and, finally, a special two-day meeting on roof control.

Jan 1, 1977