Search Documents

Effective in the 1987 Minerals Yearbook, the following changes have been made: "Asphalt" has been deleted; "Greenland" is included in the "Potash" chapter; "Meerschaum" is included in the "Clays" chapter; and "Staurolite" is included in the "Abrasive Materials" chapter. QUARTZ CRYSTAL Cultured quartz crystal production increased significantly in 198?, following 2 years of reduced production. Consumption of domestic lascas as feedstock for cultured quartz crystal increased. Imports of lascas from Brazil also increased. Although no lascas was mined in the United States during the year, the domestic producer supplied material to consumers from company stockpiles. Specimen-quality natural quartz was very much in demand; quartz crystal for this application is discussed in the Gem Stone chapter.

Jan 1, 1989

By H. W. Frevert, A. C. Fieldner, S. H. Katz

"The Bureau of Mines, in its investigations of as masks for use in mines and allied industries tests masks that are voluntarily submitted by manufacturers for examination, and issues approval certificates for masks that meet the bureau's specifications. This paper describes the tests that were conducted on an ammonia gas mask by the Bureau of Mines, which successfully met all requirements and tests for ammonia, masks. The mask tested, known as the GMD ammonia gas mask, is manufactured by the Mine Safety Appliances Co., Pittsburgh, Pa. This ammonia gas mask, which forms a pocket over the face and allows breathing through the nose, consists of a face-piece with non-shatter eyeglasses; this is attached by means of a corrugated rubber tube to a canister supported on wearer's chest by a harness. The canister is green in color and is of tinplate construction. It was a disc valve at the bottom to prevent exhalation through the canister. The filling of the canister consists of a specially impregnated activated charcoal, about 750 c.c. in volume and weighing about 520 grunn. The material is supported above the check valve by a dome of wire screen covered with toweling. Above the granular material is a filter of absorbent cotton screens, and all materials are hold firmly in place by pressure from strong"

May 1, 1926

By D. J. Bauer

Liquid-liquid extraction techniques were investigated by the Federal Bureau of Mines for the fractionation of rare-earth solutions. Separatory funnel work using tri-n-butyl phosphate (TBP) for extracting ceric nitrate from solutions containing sulfate ion resulted in almost complete extraction. Similar tests using primary amines for splitting trivalent rare-earth pairs and fractions gave promising results. The ceric nitrate extraction procedure was scaled-up by use of pressure-bubbler equipment, a series of spray towers for extraction, washing, and stripping. In this case only 84 percent ceric nitrate extraction efficiency was achieved. This work was done using dilute sulfuric acid for stripping.

Jan 1, 1960

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Le Système International d'Unités (SI) Equivalents of Common United States Units Length 1 ft (foot) = 0.30480 m Mass 1 lbm (pound mass) = 0.45359 kg Force 1 lb (pound) = 4.4482 N Volume Flow Rate 1 cfm = 0.00047195 m3/s Mass Flow Rate 1 lbm/min = 0.00756 kg/s Pressure (wg at 20° C) 1 inch wg (water gage) = 248.36 N/m2 1 inch wg = 248.36 Pa Power 1 hp (horsepower) = 0.74570 kW Energy 1 ft-lb = 1.3558 J Torque 1 lb-inch = 0.11298 N-m

Jan 1, 1977

By Thomas V. Falkie, R. Venkataramani

Hand portable truck axle scales were purchased from the Martin¬Decker Company, Santa Ana, California, for weighing the rubber-tired mine shuttle cars. The scales consisted of two hydraulic load-pads, measuring 4" thick, and 21" long by 13" wide at the pad surface and one totallizer-dial indicator unit. The development of a technique to install the scales effectively for shuttle car-weighing followed an evolutionary process. The setup which finally proved to be effective entailed countersinking and level¬ling the load pads in the floor on the shuttle car trackway such that the tops of the pads were three inches below the floor level. A plat¬form consisting of two braced side-by-side 3" x 8" lumber planks was made. The platform was placed across the load pads with six inches of overlap on each side to provide room for imperfect tracking of the shuttle car. Additionally, 3" x 8" lumber planks were imbedded across the runway immediately behind and ahead of the platform. These auxili¬ary planks were firmly braced into the floor by vertical posts or jacks set against the roof; the planks constituted a stable approach platform to enable the shuttle car to roll unimpeded onto the scale platform in either direction of travel. Figure 22 shows this arrangement in detail. The setup of the scales was done during non-production hours prior to the first working shift of the week. This task took seven to twelve hours with two men. During the actual weighing experiment, the following limitations were realized. 1. Delays will be introduced into the cycle of operations because the shuttle cars must be stopped and positioned on the platform. However, these delays can be held to a minimum, time wise, as the

Jan 1, 1972

By A. B. Cecala

A cooperative research effort was established between the Tilden Mining Company LC, the United Steelworkers of America, and the National Institute for Occupational Safety and Health to lower respirable dust levels in an iron ore grinding and concentrator plant. This cooperative effort involved three field studies to evaluate different techniques to lower respirable dust levels. The greatest impact on lowering respirable dust concentrations throughout this facility was achieved through ventilation changes. The most significant improvement was realized by changing the ventilation profile throughout the entire facility. The ventilation to this grinding and concentrator facility was provided by approximately 40 roof fans operating in either the intake or exhaust mode. The operation of these fans was significantly changed in an attempt to pro-vide more of a directional flow pattern throughout the facility, as well as to more closely balance the intake and exhaust air volume. This change accounted for a 31 pct reduction in respirable dust levels in the primary grinding area of the mill. Another successful modification was to improve the sealing of a reclaim tunnel to the outside and by barricading the access point from the reclaim tunnel to the concentrator plant. This minimized the dust liberated in the conveyor tunnels from traveling through the reclaim tunnel and into the plant. These two modifications illustrate the impact that improvements in ventilation can have on lowering respirable dust concentrations in iron ore processing facilities.

By Edward Thimons, William A. Hertbrink

The effect of wind speed upon aerosol penetration into an idealized enclosure was studied The idealized enclosure was a painted plywood box that was 1 2X1 2 XI meters in volume Two fans supplied 1 7 m3 /min of filtered air to this enclosure at a static pressure of 2 8 mm of water The enclosure had a 7 5 cm diameter vent port which was isolated from the air flow around the enclosure To simulate holes in real enclosures, three 16-cm diameter holes were drilled on the front and back sides of the enclosure This simulated enclosure was placed in a tunnel-like structure The air flow from an ultra-light air craft was directed at the front of the enclosure The air speeds were varied between 14 and 36 km/hr as measured by rotating vane anemometer Static pressure in the enclosure was measured with an electronic manometer Two optical particle counters measured the particle number concentration of particles between the 0 35 to 0 5 µm inside and outside of the enclosure Aerosol penetration into the enclosure was computed as the ratio of the aerosol concentration inside the enclosure to the concentration outside of the enclosure The enclosure static pressures measured increase from 2 8 to 3 4 mm of water (P=00001) Aerosol penetration into the enclosure increased linearly with air velocity above 20 km/hr Theoretically estimated penetrations were correlated with observed penetration into the simulated enclosure When simple linear regression was used to model the observed penetration as a function of the estimated penetration, the value of the slope was 0 69±0 12 and the P value for the regression model was less than 0 0001 These results indicate that enclosure static pressure needs to be higher than the wind's velocity pressure in order to minimize aerosol penetration into these enclosures

Jan 1, 1999

By Roberta L. Hudak, Ellsworth R. Spencer, Eric R. Bauer, Adam K. Smith

The National Institute for Occupational Safety and Health (NIOSH) is conducting research with the objective of preventing hearing loss in the mining industry. Longwall mining is one sector that has received considerable attention. Studies involving the monitoring of worker noise exposures, characterizing equipment sound levels and dominant noise sources, evaluating engineering noise controls, analyzing hearing protection device (HPD) effectiveness, and testing of improved sound level monitoring techniques specifically for longwall mining systems, are being conducted. The research efforts revealed that stageloader operators are the most exposed longwall workers, with the discharge end being the noisiest location along the stageloader. In addition, the studies have shown that using stationary dosimeters, coupled with observational data of the cutting cycle and worker habits, has the potential for improved monitoring of the effectiveness of engineering noise controls. To address the ineffective use of soft foam earplugs, a simplified 3-step method was developed for inserting soft foam earplugs. Results indicate a 9 dB greater attenuation after training subjects on the 3-step method. Finally, muff type HPDs are being evaluated for effects of speech intelligibility in noise. The combined results of these studies illustrates that much can and has been done to prevent noise-induced hearing loss (NIHL) in the mining industry, especially with respect to longwall mining workers. This paper presents an overview of ongoing studies, a progress report of results, and the implications for reducing worker noise exposures and preventing NIHL in longwall mining workers.

By Powell. Alfred R.

"An investigation has been made of the applicability to a variety of coals, other than those from Illinois, of the Powell and Parr method of analysis for the forms of sulphur in coal.A complete study was made of the sulphur in the following coals:- Upper Freeport, Pa.; Pittsburgh seam, Pa.; Pocahontas No. 3, W, Va..; Letcher Co., Ky.; Morgan Co., Tenn.; and Cherokee Co., Kan.The method of analysis gave excellent results when applied to these coals. In the determination of pyrite, the iron-sulphur ratio checked in every case with the theoretical. After the extraction of the pyrite and sulphates, the remaining sulphur was proved to be organic in nature.This work indicated that sulphur exists in coal in three typical forms: - pyrite or marcasite, sulphates, and organic sulphur. A study of the changes which these forms undergo during coking has been made on a variety of coals, and the following five classes of reactions established.First. Complete decomposition of the pyrite and marcasite to ferrous sulphide, pyrrhotite, and hydrogen sulphide. This reaction begins at 300°C., is complete at 600 °C., and generally reaches its maximum between 400 and 500°C."

Mar 1, 1920

By Steven J. Page

Overexposure to airborne respirable crystalline silica dust can cause disabling or fatal respiratory disease, and mine worker exposure to silica dust continues to be an ongoing occupational health concern. Exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern. On surface coal mine drills, bailing air flushes the cuttings out of the drill hole. Conveyor belting material is typically used to fabricate a shroud around the drill deck in an effort to contain the drill dust so that it can be captured by a collector. Dust leakage from the drill shroud is usually the worst dust source problem on most drills. The focus of this work is drill shroud dust leakage and the relationships of various drill parameters on this leakage. Experimental data were obtained and used in combination with dimensional analysis to establish these relationships. In general, it is found that airborne respirable dust (ARD) concentrations vary in a direct relationship with shroud leakage area and in an inverse relationship with drill deck cross sectional area and shroud height. This work expands the testing and dimensional analysis previously reported for collector/bailing air flow ratios ranging from 2:1 to 4:1 to include ratios approaching 1:1. A semi empirical mathematical model has been developed and expanded to describe ARD generation on surface coal mine drills. Geometric parameters included are drill deck height and cross sectional area, shroud leakage associated with the deck shroud, and the operational parameters of bailing airflow and dust collector airflow. The relationships can be described by logarithmic functions and yield predictive ARD values, which fall in the range measured on operating drills for collector/bailing air flow ratios greater than 2. However, at values of collector/bailing air flow ratios of approximately 1.1, the amount of ARD shows minimal response, if any, to drill deck shroud improvements that do not result in near perfect seals. This is a condition that can occur in actual operation and is a substantially different result than previously expected and reported. Application of these results should provide mine operators with sufficient information to determine (1) the relative magnitude of their dust emissions, (2) where they should focus their efforts to reduce ARD emissions and (3) the improvement they could reasonably expect to achieve. Given that exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern, substantial reductions of airborne silica dust during drilling may be estimated and achieved through use of the analysis presented. Keywords: drill; dust; model; dimensional analysis

Jan 1, 2008

By M. Townsend, E. L. Petsonk, B. Fedders, M. Niggemeyer, H. Abrons, E. Daniloff, J. Griffin, K. Kinsley

In certain populations, nonspecific airway hyperreactivity (HR) is associated with increased respiratory symptoms and decreased lung function. We analyzed standardized pulmonary symptom questionnaires and pre-shift spirometry with methacholine inhalation challenge (Chatham, M. et al, Chest 82: 15) on 228 control workers (C) with no known exposure to occupational hazards, and 200 underground bituminous coal miners (M). M and c were similar in age, height, sex, and smoking status. HR (defined as >15% fall in FEVI after up to 5 vital capacity breaths of 25mg% methacholine) was found in 25% of M and 28% of C (NS). M showed higher% predicted FEVI (%PFEV) than c (M 107%, C 104%*). 28% of current smokers showed HR versus 22% of never smokers (NS). Current smokers showed reduced %PFEV but were not different from lifelong non-smokers regarding prevalence of HR. Subjects with HR showed reduced %PFEV, (HR 101%, not HR 107%*) but M and c with HR showed similar reductions. M had more dyspnea and chronic cough than c*. Hyperreactivity was associated with increased symptoms in controls but not miners. In our study, the prevalence of HR in coal miners was similar to nonminers, and did not explain miners' respiratory symptoms. * P < 0.05

Jan 1, 1989

This section contains a summary of our investigation of the soil conditions (type, porosity, moisture content, etc.) at the two sites (Lanse and Kato, Pennsylvania) selected for field testing of latex as a soil sealant. Other natural conditions such as rainfall, frostline, depth of the water table, etc., were also measured and recorded for possible later use in assessing the effect of the latex seal on the total environment. The numbered sites referred to throughout this report are shown on the maps of the Lanse and Kato sites (Figures 1 and 2). KA, RB and KC are positions at the Kato site - all other numbered positions refer to the Lanse site. Two other terms used throughout the report which should be explained are “horizon” and "profile". These are synonymous terms for soil layer, A horizon (or A profile) referring to topsoil and B horizon (or B profile) referring to subsoil. The properties that control the flow of water through the soil are of special interest because these will also govern the passage of a sealant into and through the soil. Normally the particle size distribution is a good measure of soil permeability, which is directly proportional to sand content and inversely proportional to silt and/or clay content. Tables I1 and I11 show the percentages of gravel or stones, sand, silt and clay of Lanse and Kato soil samples. According to the United States Department of Agriculture classification, the gravel is ,ignored and the residue separated into sand, silt, and clay fractions. Figures 4 and 5 indicate by means of the USDk soil texture triangle that the variability of composition of Lanse soil ranges from sandy loam in the creekbed to clay loam. The variation is even greater among soil samples from Kato. Porosity of soil, also known as percent voids, is another indication of how readily water will travel through soils. Soil density usually increases and porosity decreases with depth, and as expected, the porosity of the top soil at Kato, a forest, is exceptionally porous and open (see Table IV) The pore diameter and length of soil capillaries is extremely variable, and its distribution in the field is impossible to determine. In addition to the capillaries, soil also contains many macro cracks, crevices, and passages around stones and roots. All these affect the flow rate of water through soil. Poiseuille&apos;s law states that the rate of flow of a liquid through a narrow tube is proportional to the 4th power of the radius of the tube. Pore size normally decreases with depth and in soil containing appreciable amounts of silt and clay this is especially true. Thus, deeper soils should be less permeable and such was the case at Lanse and Kato.

Jan 1, 1972

By Maria I. De Rosa

Coal mine fires pose a constant danger to the safety of miners and to their livelihood. Underground mine fires pose an added hazard because of the confined environment with remote exits. Enactment of safety regulations [30 CFR2 75 and 771 for under- ground coal mines and surface coal operations has greatly improved the safety of miners. However, mine fires and fire injuries remain serious hazards for all coal mining operations. This report analyzes mine fires and fire injuries for all U.S. coal mining categories (underground coal mines, surface of underground coal mines, surface coal mines, and coal preparation plants) during 1990-1999. Fires involving contractors are also included in the analysis. Similar analyses (for underground coal mines only) by the former U.S. Bureau of Mines (USBM) were reported by McDonald and Pornroy [I9801 and Pornroy and Carigiet [I9951 for 1950-1977 and 1978-1992, respectively. For comparison purposes, data for 1978-1 992 are mentioned in the "Underground Coal Mine Fires" section of this report. Detailed analyses of mobile equipment fires for all underground and surface coal and metal/nonmetal mining categories during 1990-1999 have recently been reported by NIOSH [De Rosa 20041. Risk rate values (fire and injury risk rates) for the 10-year period (1990-1999) and for five successive 2-year periods within the 10-year period are derived. Risk rate values for individual states for the 10-year period are also derived. Other variables by state and time period include employees&apos; working hours, lost workdays, and coal production (underground and surface coal mines only). The number of fire fatalities is reported by time period. Variables such as ignition source, method of detection and suppression, equipment involved, location, and burning material are reported by five 2-year periods only. Furthermore, the number of fire injuries per number of fires causing injuries and total fires has been analyzed by year, ignition source, equipment involved, and location. For comparison purposes, the major fire and fire injury findings for all coal mining categories have been reported. The data in this report were derived from "Injury Experience in Coal Mining" [MSHA 1991a, 1992,1993,1994a, 1995a, 1996, 1997, 1998b, 1999c, 20001, "Fire Accident Reports" [MSHA 199 1 b,c; 1994b; 1995b,c; 1998a,c,d,e,f; 1999a,b,d,e], MSHA "Fire Accident Abstracts" internal publications, and verbal communications with mine personnel. Mining companies are required by 30 CFR 50 to report to MSHA all fires that result in injuries and fires that are not extinguished within 30 min of discovery. A small number of fires lasting <30 min without injuries reported in the "Fire Accident Abstracts" have been included in this report. The analysis in this report will provide the National Institute for Occupational Safety and Health (NIOSH), the Mine Safety and Health Administration (MSHA), and the mining industry with a better understanding of the causes and hazards of mine fires and fire injuries. It will also form a basis for developing future fire research programs.

Jan 1, 2004

By L. C. Ilaley

The Buresa. ot Mines at its Pittsburgh Station conducted tests aa earl7 a.a 1911 looking into the satety of miniature electric bulba. The first teata were maie with bulbs euch as were being sold with the partly developed lamps then on the market. 'l'he.sa aarly teats demonstrated the da.nger of using minia.tu:re bulbs in explosive mine atmospheres unless the current that enet gized the glow!ng filament was in aome minner inter.N.ptecl if the glass surrounding the filanant should be broken.

Jun 1, 1922

Objective To develop a passive, inexpensive technique for monitoring explosion overpressures within sealed areas in underground coalmines. Background From 1994 to 2000, seven explosions of methane and/or coal dust occurred within the worked-out, sealed areas (gobs) of underground U.S. coal mines. These explosions, believed to have been started by lightning, destroyed many seals and caused much damage external to the sealed area. One gob explosion went undetected until the mine operator reopened the sealed area and discovered the damage. Fortunately, these gob explosions did not cause any fatalities or injuries. Because lightning occurs in just about all mining areas, several questions arise. Could gob gas explosions be occurring in other sealed areas and going undetected? If so, what is the magnitude of the resulting explosion overpressures? The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) undertook a study to identify and evaluate passive measuring devices to monitor and quantify the overpressures associated with such explosions. This work was done in parallel with full-scale explosion experiments for evaluating the strength characteristics of seals used for isolating areas in underground coal mines. Approach Evaluation studies were done in PRL&apos;s 20-liter explosion test chamber and in the full-scale Experimental Mine at Lake Lynn Laboratory to evaluate the response and accuracy of various commercially available automobile tire pressure gauges to overpressures generated from gas and dust explosions. The first series of tests was done in the 20-liter chamber, which is used to study the explosibility and inerting of fuel dusts and gases. Data from the tire pressure gauge tests were compared to the pressure-time data obtained from the 20-liter chamber &apos;s traditional electronic strain gauge pressure transducer recorded on a high-speed data acquisition system. To evaluate the tire pressure gauges, the valved inlet (tip) of the candidate pressure gauge was removed and the body of the gauge was cemented with epoxy into a 0.25-in pipe elbow and attached to the outside of the test chamber. A second series of tire gauge evaluation tests was done at Lake Lynn during explosion-resistance testing of seals used in underground coal mines. Full-scale seals (20 ft wide by 8 ft high)were constructed as one wall of a 2,000-ft3 chamber and exposed to a series of methane explosions. Average overpressures ranged from20 to 80 psi. The seals were built with various strength materials ranging from 7 to 48 in thick. The modified tire gauges are attached on the outside of the chamber to a 0.25-in NPT pipe that extends into the chamber (figure 1). The axis of the gauge is mounted at a right angle to the plane of the seal to minimize the coupling of any seal movement to the stem of the gauge that may cause inaccurate readings. The internal explosion pressure history is recorded with a strain gauge pressure transducer mounted inside the chamber. Methane is injected into the chamber, mixed with air, and ignited with an electric spark located at the geometric center of the chamber. Maximum explosion overpressures are recorded and compared with the tire gauge pressure.

Jun 1, 2001

To reduce air be respirable dust generated from emptying dry dust collectors on small truck-mounted drills used at surface coal mines.

Jan 1, 1995

By S. H. Katz, J. J. Bloomfield

In studies of mine and tunnel ventilation conducted by engineers of the Bureau of Mines , various smokes are used to determine flow of air , direction of the currents , and the rate of mixing . The instrument for generating streams of sulphur trioxide (SO ) smoke , shown in the drawing herewith, has been found helpful , convenient and practicable for such purposes ; it is also especially useful in some places where fire for generating smokes is not permissible . The apparatus consists simply of a glass tube containing fuming sulphuric acid on granular pumice stone , attached to a rubber syringe bulb . When a squeeze of the bulb blows air through the tube , a stream of dense white smoke evolves, which follows and makes visible the air currents . The tubes after preparation are hermetically sealed to prevent deterioration . When ready for use , they are easily broken open at a file scratch for the purpose on both tips , and inserted into a rubber nipple at the bulb . Sometimes it is of advantage to attach them to a longer rubber tube leading to the bulb . Tubes of the size shown (about 1/2 inch outside diameter by 5 inches long) are usually sufficient for the needs of a day . Thereafter they cease to fume because the acid absorbs moisture from the air and looses its effectiveness . Smaller sizes of tubes and larger have been made , but the size shown has proved most practicable . Immediately after a person has finished using a tube it should be buried or disposed of in a place where it will not be touched by shoes or clothing, or come in contact with wooden floors , furniture , or metals , because the acid , which will eventually leak from the tubes , is highly corrosive . -- Reports of Investigations , Department of the Interior , Bureau of Mines .

Jul 1, 1923

By John Gross

In connection with some investigations being made at '!'he Ra.re uid Precious 1ets.ls Station of the U, S. Bu.rea.u of Mines, at Reno, Nev., on the precipitation of gol'i and silver from cyanide solutions, it wa.s sug­ gested tnat the use of acetylene for this purpose be investigated, A pa.tent was iss·.ied to Fre<!.erick W. Martin and Frederick Stl1.bbs in 1900 covering the precipitation of precious metals from cyanide solu­tions by acetylene, The acetylene used in the tests described below wa3 made f'rom a. corr.:nercial cal ci \'!Z:l carbid.e, A r..umber of exper:me11. +,s rezul ted in more or lP.ss ccmplete pree;p1tatien of silver, -but 1n no case was a11Y gold precipitated. As silver acetylide, obtained by precipitatir.g the silver from an ar:::ncni'i\.Ca.l so1ut1on of silver n,. tra.te by acetylene, is yellowish white, esn:, solu'.)le in cyanide and hlghly explosive, and the pr9cip1tate ob­tain£ frcvm the cy'31lide sclutions was black, not tlubla L., cyanide and not explooive, it 'Na.s deid-,d. to ir.·.restigate the na.tur.e of the slJ.ver pre­cipit.te !rem the cy;r:iide solu·t:i.i,ns, !n prepa;.•i::lg a lge (!\,wrttity ,:f the preci-pi tte 1 t. wa, fo·und that a.fter c,:.\i;:1 ete prEc"'.pi tat ion cf the eil ver the !IOl ution con ta.ined soluble eulphic.e • Thia p:!:'O'lided a el f!W "lt·d. a.ft er apr,ropri-9.te tests the preeipita.te VIO,I proved to 'be ailver sulphide.

Apr 1, 1922

By John R. Reeves

The principal oil aha.le in Indiana ie known as the New Al'baZ\Y shale. It 11 ot Devonian age, and ia usually correlated with, although not certainly of the 1ame age a,, the Antrim shale of northern Michiga.. the Ohio shale of Ohio, and the Chattanooga shale ot Kentucky. Termescae • a."ld Georgia. The nqtmal thickneaa of the formation 1n Indiana 1e a.bout 100 faet, ltbough 1n the region of its out­ cro;l the tall th!::kne,111 io rarely exposed because cf the general d:.p of the strata, which is 11 about 30 feet per mile to the west. With the exception ot thin local pha1e1, the entire thickness is oil shale,

Aug 1, 1922

By N. S. Dalal, N. Leelarasamee, V. Castranova, K. Van Dyke, V. Vallyathan

"INTRODCICTIONSilicosis is the chronic fibrosing disease of the lungs caused by the inhalation of crystalline silica. However, inhalation of crystalline silica, may induce three distinctly different disease patterns; i.e., chrome silicosis, accelerated silicosis, and acute silicosis. These three disease patterns differ in their pathologic characteristics, clinical symptoms, onset of disease, and mortality. Many studies in the past have focused on the elucidation of mechanisms involved in the development of chrome silicosis. We recently reported that freshly fractured silica has surface properties that could make it more reactive with lung tissue than aged silica, and that this unique reactivity of freshly fractured silica may be involved in the pathogenesis of acute silicosis (Dalal et al., 1986; Vallyathan et al., 1988; Shi et II., 1988). Because freshly fractured silica could contain some moieties in an ""excited state,"" due to the breakage of silicon oxygen bonds, we postulated that the de-excitation of these moieties could produce light which could be monitored by a luminescence measurement technique. In addition, if this ""excited state'' of silica could trigger a greater biologic response by phagocytic cells, this activation could be monitored by a chemiluminescence technique in the presence of appropriate enhancers.This investigation describes for the first time the use of luminescence in the study of freshly fractured silica and its properties. Enhanced biologic reactivity of the freshly fractured silica with alveolar macrophages was monitored by the chemiluminescence technique.MATERIALS AND METHODSNative silica was obtained from the dust bank of the GenericRespirable Dust Technology Center, Pennsylvania State University, State College, PA, and ground for 3~ min in an agate ball mill. It was then sieved through a 20 micron mesh filter and used within 1 O min as fresh silica or stored in glass bottles for aging. X-ray energy spectrometry and X-ray powder diffraction studies on representative samples were made to confirm the mineralogic purity. All the silica samples were found to be 99 % pure with minimal detectable conlamination by metal ions."

Jan 1, 1990