Search Documents

By Noel N. Moebs

The Bureau of Mines measured surface subsidence above four small coal mine room-and-pillar sections in southwestern Pennsylvania, to obtain preliminary information on the magnitude and character of selected parameters, such as angle of draw and maximum subsidence, which are essential to the development of subsidence prediction methods. Data varied widely at the four sites; this is attributed to local geologic and mining conditions. Surface deformation at each site was of a magnitude normally associated with severe structural damage.

Jan 1, 1982

By W. K. Overbey

Knowledge of fracture systems in oil or gas reservoirs is essential to the efficiency of both primary and secondary production operations. A relationship was established between structural features of the surface and both natural and induced fractures in oil and gas reservoirs, thus providing a method of predicting the direction of rock fracture prior to field development and well completion. Correlations between the surface features and under-ground fractures resulted from analysis of joint strike measurements, bottom-hole impression packer surveys, photographs of hydraulically fractured wells, fracture data from oriented cores, in situ strain measurements from formation outcrops, and lineament analyses from aerial photographs. The mean orientation of surface fractures, lineaments, and stress field directions ranged from N 53° E to N 73° E, compared with an average orientation of N 63° E for the hydraulically induced fractures. Tectonic stress field was shown to influence the direction of hydraulically induced fractures. This report presents the details and application of techniques to obtain the orientation of the principal horizontal compressive stress field component and thus the direction of induced fractures.

Jan 1, 1971

By Anthony T. Lannacchione, Donald G. Puglio

The Bureau of Mines developed data on the methane content of the Hartshorne coalbed, Haskell and Le Flore Counties, Okla. The methane content is calculated to be between 1.1 and 1.5 trillion cubic feet, based on an estimate of total coal in place of 2.4 to 3.2 billion short tons. Methane increases with depth, but the rate of increase decreases with greater depths. Degasification in advance of mining is recommended for all mines operating at depths greater than 500 feet to reduce hazards and methane explosions, decrease mine ventilation costs, and conserve the natural gas that would be otherwise wasted.

Jan 1, 1979

By R. E. Head, Virgil Miller

"INTRODUCTIONRecent investigations at the Intermountain Experiment Station of the Bureau of Mines at Salt Lake City indicate that metallurgists have given little attention to the occurrence of jarosite minerals in the oxidized ores of lead and silver. These investigations have also emphasized the importance of knowing when these minerals occur in the oxidized ores, especially those containing lead, silver, and gold, as their presence is a material factor in selecting a suitable kind of treatment. Since the question of the occurrence of jarosites in oxidized ores has come to the attention of the Bureau of Mines, investigation has indicated that plumbojarosite and argentojarosite are quite common. These two minerals appear to be widely distributed and probably escaped recognition by persons who had attempted to treat certain oxidized lead ores in which the jarosite minerals represented a material portion of the metal content.Consideration of the physical characteristics of the jarosites also indicates that in many cases failure to treat some of the oxidized lead ores with success has been directly due to the fact that the greater portion of their lead and silver content was present as plumbojarosite and argentojarosite. The data and the description of these minerals given in the body of this paper indi¬cate that attempts to recover lead and silver from ores in which appreciable amounts of the metals occur as plumbojarosite and argentojaeosite would be unsuccessful if confined to gravity methods of concentration. There are un-doubtedly considerable tonnages of oxidized lead ores in the various mining regions of this and other countries, and it is quite probable that in some of these ores the metal content of lead and silver may be largely anglesite (lead sulphate) and cerussite (lead carbonate) but that they will also contain cerargyrite (silver chloride), argentojarosite, and plumbojarosite. The treatment of such ores therefore presents an important problem, since a product is discarded from ores from which the recoveries of lead and silver have been below 70 per cent which is probably too low-grade to warrant aftertreatment by any process now in use."

Apr 1, 1928

By Joseph V. Mather, E. H. McCleary

"INTRODUCTION Workmen are transported in shafts in various types of cages or skips, most of which were designed primarily for hoisting cars and materials. Therefore, in general the cages or skips are not completely enclosed, adequate and gates are not always provided, and at many mines signaling devices and telephones are re¬stricted to those at the various landings in the shafts.Shaft accidents are usually severe - frequently fatal - and as a rule such an accident is caused by failure to comply with company rules or by ignoring them.Sixty men were killed and 555 men were injured in shafts of the anthracite and bituminous coal mines of the United States during the 5-year period 1938-42. 4/ Many of these accidents could have been prevented by having properly enclosed cages and adequate locking devices on doors to prevent workmen from falling into the shafts.The officials of the Heidelberg Coal Co. contemplated utilizing an old coal-hoisting shaft as a man-hoisting shaft; however, it was their desire to avoid the use of the conventional cage and to try to provide a safer means of transporting men in the shaft. Investigations and studies made by the officials revealed that an elevator similar to those used in large buildings would be more economical in first cost, maintenance, and operating costs would be less, and it would be safer and more convenient for the workmen. Effective safety devices for such elevators have been developed to such a high degree that those properly installed seldom fail. The elevator or man cage finally chosen cannot be pulled above the top landing through mechanical or man failure; it stops automatically at each landing and cannot be moved while a door is open; when the cage leaves the landing the doors opening to the shaft are automatically locked by mechanical and electrically operated locks; electric lights, telephone communication, and push-bottom controls are available on the cage, and adequate safety switches and overspeed controls are provided."

Jun 1, 1947

By J. J. Bourquin, S. H. Katz

"Three types of respiratory apparatus namely, gas masks, hose masks, and self-contained oxygen-breathing apparatus - are now commonly used for protection from noxious gases, vapors, and smokes or ristes, but no particular type can be selected as best for all conditions. Many factors must be considered in connection with each situation, so that each must be considered as a problem in itself. Following are concise statements for comparing the types:Gas masks are the simplest and easiest to wear, also the least cumber-sore; but they protect only in comparatively low concentrations of noxious gases and should never be used where the air contains less than 16 per cent of oxygen. Special masks give protection from one gas or class of gases, but may give no protection against another gas or class of gases.Hose masks protect in any irrespirable atmosphere, but are somewhat cumbersome, the length of hose limiting the distance a wearer may go from fresh air. They are serviceable also where a supply of pure air moves with the wearer, as where a locomotive engineer in a smoky tunnel is using a hose mask supplied with air from the compressed air line of the locomotive. Hose masks consume no chemicals or materials and so are not limited in the time they may be used.Self-contained oxygen-breathing apparatus protect in any irrespirable atmosphere, but their weight is cumbersome, they can be used only by trained men, and frequent attention must be given them to maintain good working condition. On the other band they are the only safe means for exploring mines and other places filled with irrespirable gases in high concentrations."

Jun 1, 1923

Detect fires in or near mine shafts, isolate smoke filled areas, and remotely extinguish fire. Approach A system (of sensors, automatic alarms, an aboveground control console, remotely operated ventilation doors, and sprinklers) has been built from off the-shelf components, and fire, tested in two mines. How It Works The system uses three different kinds of sensors that can detect the heat or smoke of a fire and automatically actuate alarms. When the alarm sounds in the control center on the surface, water sprays in the mine shaft and shaft station areas can be remotely turned on to deluge both the inside and the outside of the mine shaft's wooden support structure. To protect miners from toxic fumes, smoke control doors can be closed or opened, either remotely from the control center or directly by miners using the manual or electrical actuators at the door locations. Man doors built into each ventilation door allow persons to pass without opening the main door.

Jan 1, 1977

By Ryron O. Pickard

"The Berkeley safety station of the U. S. Bureau of Mines was recently informed that a geologist was killed through entering an abandoned 90-foot exploratory shaft without making a preliminary test of the shaft atmosphere. He was one of a geological party which was investigating coal lands in California. The only light that he carried into the shaft was an electric flash light. After he had descended a short distance, one of his associates on the surface heard him exclaim, ""This place is full of gas, I am coming up"", He had no more than finished the remark when he was seen to lose his grip on the ladder and fall down the shaft. He was apparently weakened from impure air in the shaft, and could no longer suppers himself on the ladder. When his body was recovered, it was found that his neck had been broken by the fall.This is the ;second recent accident that has been called to the writer's attention where a life has been lost in abandoned exploratory workings; the other fatality being in Minnesota where a mining engineer was overcome while sampling a shallow pit in iron-ore formations. This engineer was on the bottom of the shallow pit and died before help could reach him. It was generally supposed that each of these deaths were due to poisonous gases, but the writer believes, after reviewing the information available, that death in both instances may have been directly caused by deficiency in oxygen.Frequently in the daily press there are items relative to lives being lost through cleaning out old wells, and as a general rule such accidents are also caused by impure atmospheres.In every abandoned shaft or pit, or in fact, any old working where the air has been stagnant for a considerable time, there is always danger of oxygen deficiency, as the oxygen which originally comprised one-fifth of the atmosphere may be appreciably replaced by gases that do not support life, usually by carbon dioxide (black damp) or methane (fire damp). Much valuable information on the subject of mine atmospheres, mine gases, and the effect of oxygen deficiency onthe human system is contained in Miners' Circular 14, ""Gases Found in Coal Mines"" by G.F. Burrell and F. M. Seibert; Technical Paper 122, ""Effects of Oxygen Deficincy on Small Animals and Men"", by G. A. Burrell and G. G. Oberfell; and ''Chit of Properties of Mine Gees"" by G. A. Burrell. These publications of the Bureau of Mines should be rent by all who are interested in the subject of this paper."

Nov 1, 1921

By C. B. Manula, R. L. Sanford, R. A. Rivell

A - Contains the coordinate pair information for deriving the co¬efficients of the 3rd degree polynomial which approximates the loading station equation. C(N) - Coefficients for third degree approximating polynomial. I - General DO LOOP variable. K - Position in BRANCH of next character. L - Format specification in DEFINE FILE statement. X - Uniform displacement for random uniform number. Y - Load increment At. AO-A3 - Coefficients of approximating polynomial for loading station equation. GR - Grade direction, or grade resistance. IQ - Counts quadruples of distance grade speed and end of route for determining total distance. IT - Intersection counter in XXXDEF. Il - Station number trip is leaving. Jl - Station number for trip destination. J2-J8 - Motor assignments and functions for given trip. KK - Location of starting grade and distance in DISTGR KK - Position of decimal point in real number. KZ - DO LOOP variable for motor assignment check. LL - Location of ending grade and distance in DISTGR. Ll - Position in IECB of station satisfied. L3 - Next available position for IECB sort. MM - Flag for printing the failure of sanding to overcome slippage. NN - Trip destination in MOTSER RR - Rolling Resistance. XK - Station level or type.

Jan 1, 1974

By Joseph C. Zelanko, Anthony T. Iannacchione

One of the most difficult and longstanding engineering problems associated with coal mining is the catastrophic failure phenomenon known as coal mine bursts (known in the United States as bumps). For more than 70 years, researchers and practitioners have attempted to determine whether this destruction observed underground is caused by stress conditions within the coal pillar or from distant seismic sources in the mine roof and floor strata. The role of confinement and the extent of failure in solid pillars and panels have also proven difficult to define. These are important issues, since control solutions need to be based on a fundamental understanding of the problem. Obsenations by U.S. Bureau of Mines researchers over the last decade have helped to clarify certain aspects of these issues. Microseismic sensors and geomechanic field measurements have located areas of excess energy release, identified stress conditions in coalbeds close to failure, and recorded the response of mine structures prone to bursts. In the present study, data available for a range of U.S. bursts were considered in an effort to evaluate both common and distinctive features. Although the attempt revealed little commonality, encouraging results were produced by categorizing coal bursts by source mechanisms. When a coal burst is thus categorized, differences in environmental factors-such as geology, stress fields, and mining methods-are highlighted, and viable control strategies are readily recognized.

By Kenneth O. Bennington

This investigation is part of the Bureau of Mines research effort directed at advancing mineral technology and minimizing energy requirements for extractive metallurgy. The emplacement of the primary minerals petalite (LiAlSi4010) and spodumene (LiAlSi206) in the lithium pegmatites is examined on the basis of their Gibbs energies of formation determined from lithium metastltcate and oxides, using a series of proposed reactions. The reaction between spodumene, quartz, and petalite (LiAlSi206 + 25i02 [=] LiAlSi4010) apparently does not take place in nature but may be proved experimentally.

Jan 1, 1982

Provide the mining industry with a method for determining the gas content of ore bodies and associated strata for use in mine planning, Approach Samples of various rock types are collected and tested to determine gas content in conjunction with sample size, the collection method (i.e. whether the sample was collected from a core sample or by hand) mine gas emission, and the geologic location from which the sample was taken, such as near a fault, outburst area, or other geologic anomaly. How It Works Two methods were developed by the Bureau of Mines to determine the gas contents of rock samples. The first method developed involved dissolving minerals to measure gas emission. This method, however, can only be used with soluble minerals. A second method, therefore, was developed for use with insoluble minerals. With this method, the sample is crushed in a ball mill. Although the dissolution method is faster and more accurate to use, the crushing method is also advantageous because its use can more closely approximate a mining situation; the sample is crushed as in mining and the amount of gas released relates to the amount of gas that would be released during a mining operation. The dissolution method is applied to soluble minerals, such as rock, salt, or trona, in a sealed chamber. Gases released during dissolution are collected for analysis by gas chromatography. One advantage in using the dissolution method is that the test apparatus is relatively inexpensive. In addition, test can be performed at any scale, from single crystal samples to a solution mining operation.

Jan 1, 1983

By Todd M. Ruff

The lack of visibility near earthmoving equipment resulted in six fatalities in U.S. surface mining operations during 2003. These accidents were the result of either a piece of equipment striking another vehicle or worker, or the equipment traveling over the edge of an embankment. Figure 1 is an example of a recent accident that resulted in serious injuries to one worker and fatal injuries to two others when a van parked in front of a haul truck. Two fatalities occurred in separate incidents when front-end loaders struck workers. Another two workers were killed when their equipment backed over the edge of a highwall or dump point [1]. There is clearly a need to provide better information to equipment operators regarding their surroundings. [ ] Researchers at the National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory, are working to reduce these accidents by developing systems that sense obstacles and changes in terrain near the equipment and provide this information to the operator. Many off-the-shelf proximity warning systems that were developed for automobiles, light trucks, and recreational vehicles were evaluated on off-highway dump trucks [2]. Many limitations were found with existing systems, including frequent false alarms, limited detection range, a lack of specific information on an obstacle (e.g., location, identity), difficulties in finding suitable mounting locations, and an inability to withstand the environment. These limitations have necessitated the development of new systems designed specifically for large, off-highway, earthmoving equipment. New off-the-shelf systems available for mining equipment include radar and tag-based detection systems. Prototype systems now being developed include a proximity warning system based on the Global Positioning System (GPS) and a computer-assisted stereovision system. Development of these new systems was accomplished by working with manufacturers to modify existing systems to meet the needs of surface mining and through cooperative research with organizations to develop completely new solutions. A typical proximity warning system consists of a sensor or antenna mounted on the equipment that detects the presence of obstacles and an alarm interface in the cab of the equipment. Some systems, as described in more detail below, also require that other vehicles and personnel on the ground be outfitted with electronic tags that transmit an “I’m here” signal back to the system (e.g., radio signal detection systems or GPS). Many types of proximity warning systems are on the market, but they are not all discussed in this paper. APPROACH In past work, engineers at NIOSH evaluated several off-the-shelf proximity warning technologies in order to verify their effectiveness on off-highway dump trucks [2]. Dump trucks were chosen because of the number and severity of accidents involving this type of equipment and because extensive blind areas around these trucks are typical. This experience allowed engineers to limit the number of systems chosen for long-term tests at mine sites to those systems showing

By 1928-05-01

"The carnotite ores of Colorado and Utah were the chief source of radium for many years. In the fall of 1922; news of the very rich deposits of radium ore discovered in the Belgian Congo caused almost complete cessation of domestic production. The Congo ore contains pitchblend and a number of alteration products, including the new minerals bequerelite, curite, kasolite, stasite, and dewindite. Reports indicate that a considerable amount of ore containing over 50 per cent U308 has been produced. It seemed certain that radium could be extracted from the Congo ore at a much lower cost than from the relatively low-grade carnotite; and in order to preserve their elaborate marketing organizations, the larger American producers made agreements with the Belgium syndicate to market the foreign product in this country. The price of radium has been held at $70 per milligram. Extraction of radium from carnotite by the usual methods does not appear to be profitable at that price. With one exception, all American firms ceased production after their accumulated stocks of ore had been treated. The United States Radium Co., which continued to treat carnotite for several years, has recently shut down its plant.Although there is probably a large profit derivable from the treatment of Congo ore, it is not likely that the Belgium Syndicate will meet sufficient competition to cause any reduction in the present quotations. It is not known how long the high-grade ore will last, but when exhausted the price of radium may be expected to advance. According to K. L. Kithil3 it is the opinion of interested parties that, so far as can be forseen, radium will in future years never again be obtained at the present low price.Carnotite contains the valuable element, vanadium, which is not present in the Congo ore. The recovery of-vanadium is an important factor in the cost of extracting radium from carnotite, and under favorable conditions carnotite can be profitably treated for the vanadium alone. Vanadifecous sandstones are found ranging all the way from roscoelite (vanadium mica), containing little or no uranium; to a high-uranium and low-vanadium carnotite. Ores containing 2 per cent or more U308 are classed as radium ore and are sold on the basis of the uranium content, which is proportional to the radium content. Only in exceptional cases have ores been evaluated on the basis of both the radium and vanadium contents, although the presence of vanadium has undoubtedly influenced the price of radium ore."

May 1, 1928

By Jon C. Volkwein

Dust concentrations inside and outside enclosed cabs on several types of mining machinery were measured by the Bureau of Mines. Results indicated that properly enclosed cabs can offer significant dust protection for machine operators. Recommendations for improvements in cab technologies were discussed.

Jan 1, 1979

Avoid accidents that can occur when applying belt dressing from an aerosol can, particularly when can pressure has dropped or when spraying against wind. Approach Use a garde-type sprayer. How It Works Commercially available garden-type sprayers can be used for applying conveyor belt dressing from 12 feet away, or more. Pressure is easily raised and maintained at about 50 psi. Most sprayers have a hand pump, but a battery-powered cordless model is also available. Garden-type sprayers are available in various sizes from 11/2 to 18 gallons, with the larger models wheel mounted. The 3-gallon model evaluated by the Bureau has a shoulder carrying strap, which gives additional safety advantages. Use of the strap frees both hands for climbing ladders or holding onto catwalk rails. When spraying, one hand can remain on a handhold to lessen the chances of touching a moving belt.

Jan 1, 1980

Develop methods of enhancing and measuring the high-temperature softening and melting properties of iron oxide pellets reduced under simulated blast furnace smelting conditions. Approach Add dolomite and Limestone flux and a low-cost organic binder, such as starch, carboxyl methylcellose (CMC), or waste papermill sludge, to the iron oxide concentrate to produce hematite (ferric oxide) pellets with superior high-temperature metallurgical properties. Simultaneous increases in softening temperature, gas permeability, and enhanced metallization rates are sought to improve blast furnace productivity and energy efficiency. Background In the past, bentonite, an inorganic binder, was the only additive (binder) used in the production of pellets made from iron ore concentrate. Research has shown that the reducibility of conventional (acid) pellets can be increased by the addition of flux or an organic binder. The increase in pellet reducibility results in less wustite in the center of the pellet at high temperatures, such as those obtained in the cohesive zone of the blast furnace.

Jan 1, 1990

By R. Unger, L. Mallett

The use of virtual reality (VR) technologies to train miners is an evolving area in research and development. In July 2006, representatives of 14 international organizations met to discuss current VR-related efforts and explore ways to employ VR in the future. This paper gives an overview of the various approaches presented at the meeting and discusses directions for future implementation. An example of a training package that teaches mine map-reading skills is presented. The meeting was the first step to building collaborations for furthering VR applications for mining. Planning has begun for a 2008 meeting open to broader participation. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

By E. D. Gardner

"The Bureau of Mines receives many inquiries concerning favorable areas in which to prospect for gold, procedure to be followed, equipment required, and allied subjects. This circular has been prepared for use in reply to these inquiries.Interest in gold mining and prospecting for gold remains steady. From time to time many people take to the field to search for new gold deposits. A large percentage of them have had no previous experience in prospecting for lode gold; this paper has been written with the hope that it might assist these newcomers.A majority of the metal mines in the United States have been discovered by qualified prospectors who were searching for valuable minerals at the time. Chance, however, always has played a large part in finding mineral deposits. Some of the discoveries of the past were made by men on other errands, such as rounding up burros or hunting game. Accidental discoveries of ore bodies have been made in building roads and trails and in excavating for mine struc¬tures. Evidence of ore has been brought to the surface by burrowing animals and by ants; gold found in the craws of fowl has led to discoveries of deposits. Important discoveries have been made by men who had no knowledge of rocks or minerals; on the other hand, many ore bodies have been found by experienced prospectors, sometimes after hundreds of untrained men had already passed over the ground.The prospector who carries on his work diligently and intelligently is of course more likely to be rewarded for his efforts than the lazy or unintelligent worker; nevertheless, it is obvious that if valuable deposits are not present at the place being prospected none will be found. Conscientious and painstaking efforts to trace gold to its source usually disclose nothing more valuable than some narrow, unworkable seams; however, many deposits that were developed into profitable mines were found by this method of prospecting. Although some prospectors have made several lucky strikes, many others have spent their working lives searching for gold without finding anything worth while. Probably only one prospector out of several thousand ever finds anything worth developing. Moreover, only 1 out of every 300 or 400 properties developed becomes a profitable mine.Prospecting was begun in the Western States in the fifties as the miners looked for the source of gold found in placers. The search for gold has been continuous since that time; the number of prospectors in the field at any one time, however, has varied greatly. Except in some desert regions, practicallyall of the placer fields now being worked were discovered by old timers; more-over, most of the important gold districts were found by early prospectors. Important discoveries of lode mines, however, have been made from time to time. Most of the area in the mining regions of the West has been searched many times by prospectors, and nearly all of the easily found deposits have been located, but it is reasonable to expect that new gold mines will continue to be found. Most of the future discoveries undoubtedly will be of deposits that do not outcrop. Prospecting for such deposits requires considerable digging.Several important discoveries were made in 1934. One of these, the Rogers-Gentry gold mine at the edge of Antelope Valley in Los Angeles County, Calif., was found by an experienced prospector on an old patented homestead a number of miles from the nearest producing mine. The initial discovery at this mine was an iron-stained, decomposed, silicous limestone outcrop, with no vein structure evident at the surface, near a small, barren quartz outcrop and a water seep. Another discovery, the Silver Queen gold mine, in the same general region and near Mojave, Calif., was found by an experienced miner on an open fraction 400 by 1,400 feet in size between two old properties that were thought to have been worked out years ago. The Silver Queen discovery was made as the result of finding a"

Feb 1, 1950

By R. V. Ramani, S. Shankar

"A convective dispersion model has been utilized to calculate the real-time airborne dust concentration in mine airways using re-entrainment as the only source term for airborne dust. It incorporates two important sources of re-entrainment in mines -- air velocity and movement of objects. The model has a sink term accounting for the deposition of particles along the airway. The model is solved using a finite difference scheme which is coded for computer. The computer model outputs airborne respirable and total dust concentrations along the airway as a function of time. The real-time and average gravimetric concentrations from several in-mine experiments were compared with the results from the simulation of the experimental conditions. This model can be used for estimating airborne dust entrainment due to air velocity, equipment movement, and persons walking. INTRODUCTIONEdwards and Ford (1988) developed a model for coal dust explosion suppression and utilized a predetermined value of threshold velocity for flowing air to pick up dust from floor. Depending on the strength of the removal forces, re-entrainment can increase the airborne dust concentration in mine airways. The most prevalent forces causing re-entrainment in mine airways are the drag and lift forces due to flowing air, and removal forces due to the movement of persons and vehicles. Shankar and Ramani (1991) have investigated the unique characteristics of the re-entrainment phenomenon in mine airways. Experiments on re-entrainment of coal dust particles were conducted in mine airways, and in a wind tunnel (Shankar and Ramani, 1994a, and 1994b). The results from the two experimental studies were found to compare well (Shankar and Ramani, 1995). There is no reported model to determine the airborne dust concentrations due to airflow or persons walking under conditions existing in mines. The present study is a part of a continuing research project in the Generic Mineral Technology Center for Respirable Dust on the spatial and temporal behavior of airborne dust in mine airways (Ramani, 1983)."

Dec 1, 1996